| Age | Commit message (Collapse) | Author |
|---|
|
- support for Touch Bars on x86 MacBook Pros (Kerem Karabay)
|
|
- fix for behavior of the hid-mcp2221 driver for !CONFIG_IIO cases
(Heiko Schocher)
|
|
- support for Wake-on-touch in intel-thc (Even Xu)
- support for "Input max input size control" and "Input interrupt delay"
I2C features in order to improve compatibility of THC devices with
legacy HIDI2C touch devices (Even Xu)
|
|
- hardening of HID core parser against conversion to 0 bits in s32ton()
by buggy/malicious devices (Alan Stern)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD changes:
- Apart from a binding conversion to yaml, only minor changes/small
fixes have been merged.
Raw NAND changes:
- Minor fixes for various controller drivers like DMA mapping checks,
better timing derivations or bitflip statistics.
- some Hynix NAND flashes were not supporting read-retries, so don't
even try to do it
SPI NAND changes:
- In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
- Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
SPI NOR changes:
- A notable changes is the fix for exiting 4-byte addressing on
Infineon SEMPER flashes. These flashes do not support the standard
EX4B opcode (E9h), and use a vendor-specific opcode (B8h) instead.
- There is also a fix for unlocking flashes that are write-protected
at power-on. This was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all()"
* tag 'mtd/for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (26 commits)
mtd: spinand: winbond: Add comment about the maximum frequency
mtd: spinand: winbond: Enable high-speed modes on w35n0xjw
mtd: spinand: winbond: Enable high-speed modes on w25n0xjw
mtd: spinand: Add a ->configure_chip() hook
mtd: spinand: Add a frequency field to all READ_FROM_CACHE variants
mtd: spinand: Fix macro alignment
spi: spi-mem: Take into account the actual maximum frequency
spi: spi-mem: Use picoseconds for calculating the op durations
mtd: rawnand: atmel: set pmecc data setup time
mtd: spinand: propagate spinand_wait() errors from spinand_write_page()
mtd: rawnand: fsmc: Add missing check after DMA map
mtd: rawnand: rockchip: Add missing check after DMA map
mtd: rawnand: hynix: don't try read-retry on SLC NANDs
mtd: rawnand: atmel: Fix dma_mapping_error() address
mtd: nand: brcmnand: fix mtd corrected bits stat
mtd: rawnand: renesas: Add missing check after DMA map
mtd: spinand: gigadevice: Add support for GD5F1GM9 chips
mtd: nand: brcmnand: replace manual string choices with standard helpers
mtd: map: Don't use "proxy" headers
mtd: spi-nor: Fix spi_nor_try_unlock_all()
...
|
|
- avoid setting up battery timer for Apple and Magicmouse devices without
battery (Aditya Garg)
|
|
- fix for potential NULL pointer dereference in hid-apple that could be caused
by malicious device with APPLE_MAGIC_BACKLIGHT quirk present triggering
overflow in data field (Qasim Ijaz)
- third party trackpart support for MacBookPro15,1 (Aditya Garg)
- Apple Magic Keyboard A311[89] USB-C support (Aditya Garg, Grigorii Sokolik)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is the usual collection of primarily clk driver updates.
The big part of the diff is all the new Qualcomm clk drivers added for
a few SoCs they're working on. The other two vendors with significant
work this cycle are Renesas and Amlogic. Renesas adds a bunch of clks
to existing drivers and supports some new SoCs while Amlogic is
starting a significant refactoring to simplify their code.
The core framework gained a pair of helpers to get the 'struct device'
or 'struct device_node' associated with a 'struct clk_hw'. Some
associated KUnit tests were added for these simple helpers as well.
Beyond that core change there are lots of little fixes throughout the
clk drivers for the stuff we see every day, wrong clk driver data that
affects tree topology or supported frequencies, etc. They're not found
until the clks are actually used by some consumer device driver.
New Drivers:
- Global, display, gpu, video, camera, tcsr, and rpmh clock
controller for the Qualcomm Milos SoC
- Camera, display, GPU, and video clock controllers for Qualcomm
QCS615
- Video clock controller driver for Qualcomm SM6350
- Camera clock controller driver for Qualcomm SC8180X
- I3C clocks and resets on Renesas RZ/G3E
- Expanded Serial Peripheral Interface (xSPI) clocks and resets on
Renesas RZ/V2H(P) and RZ/V2N
- SPI (RSPI) clocks and resets on Renesas RZ/V2H(P)
- SDHI and I2C clocks on Renesas RZ/T2H and RZ/N2H
- Ethernet clocks and resets on Renesas RZ/G3E
- Initial support for the Renesas RZ/T2H (R9A09G077) and RZ/N2H
(R9A09G087) SoCs
- Ethernet clocks and resets on Renesas RZ/V2H and RZ/V2N
- Timer, I2C, watchdog, GPU, and USB2.0 clocks and resets on Renesas
RZ/V2N
Updates:
- Support atomic PWMs in the PWM clk driver
- clk_hw_get_dev() and clk_hw_get_of_node() helpers
- Replace round_rate() with determine_rate() in various clk drivers
- Convert clk DT bindings to DT schema format for DT validation
- Various clk driver cleanups and refactorings from static analysis
tools and possibly real humans
- A lot of little fixes here and there to things like clk tree
topology, missing frequencies, flagging clks as critical, etc"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (216 commits)
clk: clocking-wizard: Fix the round rate handling for versal
clk: Fix typos
clk: spacemit: ccu_pll: fix error return value in recalc_rate callback
clk: tegra: periph: Make tegra_clk_periph_ops static
clk: tegra: periph: Fix error handling and resolve unsigned compare warning
clk: imx: scu: convert from round_rate() to determine_rate()
clk: imx: pllv4: convert from round_rate() to determine_rate()
clk: imx: pllv3: convert from round_rate() to determine_rate()
clk: imx: pllv2: convert from round_rate() to determine_rate()
clk: imx: pll14xx: convert from round_rate() to determine_rate()
clk: imx: pfd: convert from round_rate() to determine_rate()
clk: imx: frac-pll: convert from round_rate() to determine_rate()
clk: imx: fracn-gppll: convert from round_rate() to determine_rate()
clk: imx: fixup-div: convert from round_rate() to determine_rate()
clk: imx: cpu: convert from round_rate() to determine_rate()
clk: imx: busy: convert from round_rate() to determine_rate()
clk: imx: composite-93: remove round_rate() in favor of determine_rate()
clk: imx: composite-8m: remove round_rate() in favor of determine_rate()
clk: qcom: Remove redundant pm_runtime_mark_last_busy() calls
clk: imx: Remove redundant pm_runtime_mark_last_busy() calls
...
|
|
- add support for operating modes (Basavaraj Natikar)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Updated chip support in existing drivers:
- ina238: Support for INA228
- pmbus/tps53679: Support for TPS53685
- pmbus/adp1050: Support for adp1051, adp1055 and ltp8800
- corsair-psu: Support for HX1200i Series 2025
- pmbus/isl68137: Support for RAA229621
- asus-ec-sensors: Support for ProArt X870E-CREATOR WIFI and
Other notable changes:
- adt7475: Support for #pwm-cells = <3>
- amc6821: Cooling device support
- emc2305: Support for PWM frequency, polarity and output
- Add missing compatible entries to various devicetree bindings
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (34 commits)
dt-bindings: hwmon: Replace bouncing Alexandru Tachici emails
hwmon: (ina238) Add support for INA228
dt-bindings: Add INA228 to ina2xx devicetree bindings
hwmon: (ina238) Fix inconsistent whitespace
dt-bindings: hwmon: adt7475: Allow and recommend #pwm-cells = <3>
hwmon: (adt7475) Implement support for #pwm-cells = <3>
hwmon: (pmbus/tps53679) Add support for TPS53685
dt-bindings: trivial: Add tps53685 support
hwmon: (pmbus/adp1050) Add regulator support for ltp8800
hwmon: (pmbus/adp1050) Add support for adp1051, adp1055 and ltp8800
dt-bindings: hwmon: pmbus/adp1050: Add adp1051, adp1055 and ltp8800
hwmon: (max31827) use sysfs_emit() in temp1_resolution_show()
hwmon: (ltc4282) convert from round_rate() to determine_rate()
hwmon: (corsair-psu) add support for HX1200i Series 2025
dt-bindings: hwmon: pmbus: ti,ucd90320: Add missing compatibles
dt-bindings: hwmon: maxim,max20730: Add maxim,max20710 compatible
dt-bindings: hwmon: lltc,ltc2978: Add lltc,ltc713 compatible
dt-bindings: hwmon: ti,lm87: Add adi,adm1024 compatible
dt-bindings: hwmon: national,lm90: Add missing Dallas max6654 and onsemi nct72, nct214, and nct218
hwmon: (w83627ehf) make the read-only arrays 'bit' static const
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"Two fixes for the mediatek and the imx-tpm driver. Both are old
(v4.12-rc1 and v5.2-rc1 respectively).
The mediatek issue is that both period and duty_cycle were configured
to higher values than requested. For most applications the period part
is no tragedy, but a PWM that is configured for duty_cycle = 0 should
really emit a constant inactive signal. That was noticed by an LED not
being completely off in this case (two commits for one fix: a
preparatory one and the actual fix in the second one).
For the imx-tpm PWM driver the fixed issue is that the first period is
quite a bit too long under some circumstances. So it might take up to
UINT32_MAX << 7 clock ticks until the PWM starts toggling. With an
assumed input clock rate of 166 MHz (completely made up) that's 55
minutes"
* tag 'pwm/for-6.17-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: imx-tpm: Reset counter if CMOD is 0
pwm: mediatek: Fix duty and period setting
pwm: mediatek: Handle hardware enable and clock enable separately
|
|
In the merge 260f6f4fda93 ("Merge tag 'drm-next-2025-07-30' of
https://gitlab.freedesktop.org/drm/kernel"), the formatting in the
conflict resolution doesn't match what `make rustfmt` wants to make it.
Fix it up appropriately.
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- v4l2 core:
- sub-device framework routing improvements
- NV12M tiled variants added to v4l2_format_info
- some fixes at control handler freeing logic
- fixed H264 SEPARATE_COLOUR_PLANE check
- new staging driver: Intel IPU7 PCI
- Rockchip video decoder driver got promoted from staging
- iris: added HEVC/VP9 encoder/decoder support
- vsp1: driver has gained Renesas VSPX support
- uvc:
- switched to vb2 ioctl helpers
- added MSXU 1.5 metadata support
- atomisp: GC0310 sensor driver cleanups in preparation for moving it
out of staging
- Lots of cleanup, fixes and improvements
* tag 'media/v6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (310 commits)
media: rkvdec: Unstage the driver
media: rkvdec: Remove TODO file
media: dt-bindings: rockchip: Add RK3576 Video Decoder bindings
media: dt-bindings: rockchip: Document RK3588 Video Decoder bindings
media: amphion: Support dmabuf and v4l2 buffer without binding
media: verisilicon: postproc: 4K support
media: v4l2: Add support for NV12M tiled variants to v4l2_format_info()
media: uvcvideo: Use a count variable for meta_formats instead of 0 terminating
media: uvcvideo: Auto-set UVC_QUIRK_MSXU_META
media: uvcvideo: Introduce V4L2_META_FMT_UVC_MSXU_1_5
media: uvcvideo: Introduce dev->meta_formats
media: Documentation: Add note about UVCH length field
media: uvcvideo: Do not mark valid metadata as invalid
media: uvcvideo: uvc_v4l2_unlocked_ioctl: Invert PM logic
media: core: export v4l2_translate_cmd
media: uvcvideo: Turn on the camera if V4L2_EVENT_SUB_FL_SEND_INITIAL
media: uvcvideo: Remove stream->is_streaming field
media: uvcvideo: Split uvc_stop_streaming()
media: uvcvideo: Handle locks in uvc_queue_return_buffers
media: uvcvideo: Use vb2 ioctl and fop helpers
...
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-fixes-6.17-2025-07-31:
amdgpu:
- DSC divide by 0 fix
- clang fix
- DC debugfs fix
- Userq fixes
- Avoid extra evict-restore with KFD
- Backlight fix
- Documentation fix
- RAS fix
- Add new kicker handling
- DSC fix for DCN 3.1.4
- PSR fix
- Atomic fix
- DC reset fixes
- DCN 3.0.1 fix
- MMHUB client mapping fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250731191916.255648-1-alexander.deucher@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Ira Weiny:
"Header file cleanups. Specifically use specific headers rather than
just kernel.h in libnvdimm.h to reduce header file usage.
The second patch is a fix to CXL but is going through my tree as a
libnvdimm patch caused the issue"
* tag 'libnvdimm-for-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
cxl: Include range.h in cxl.h
libnvdimm: Don't use "proxy" headers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd
Pull iommufd updates from Jason Gunthorpe:
"This broadly brings the assigned HW command queue support to iommufd.
This feature is used to improve SVA performance in VMs by avoiding
paravirtualization traps during SVA invalidations.
Along the way I think some of the core logic is in a much better state
to support future driver backed features.
Summary:
- IOMMU HW now has features to directly assign HW command queues to a
guest VM. In this mode the command queue operates on a limited set
of invalidation commands that are suitable for improving guest
invalidation performance and easy for the HW to virtualize.
This brings the generic infrastructure to allow IOMMU drivers to
expose such command queues through the iommufd uAPI, mmap the
doorbell pages, and get the guest physical range for the command
queue ring itself.
- An implementation for the NVIDIA SMMUv3 extension "cmdqv" is built
on the new iommufd command queue features. It works with the
existing SMMU driver support for cmdqv in guest VMs.
- Many precursor cleanups and improvements to support the above
cleanly, changes to the general ioctl and object helpers, driver
support for VDEVICE, and mmap pgoff cookie infrastructure.
- Sequence VDEVICE destruction to always happen before VFIO device
destruction. When using the above type features, and also in future
confidential compute, the internal virtual device representation
becomes linked to HW or CC TSM configuration and objects. If a VFIO
device is removed from iommufd those HW objects should also be
cleaned up to prevent a sort of UAF. This became important now that
we have HW backing the VDEVICE.
- Fix one syzkaller found error related to math overflows during iova
allocation"
* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd: (57 commits)
iommu/arm-smmu-v3: Replace vsmmu_size/type with get_viommu_size
iommu/arm-smmu-v3: Do not bother impl_ops if IOMMU_VIOMMU_TYPE_ARM_SMMUV3
iommufd: Rename some shortterm-related identifiers
iommufd/selftest: Add coverage for vdevice tombstone
iommufd/selftest: Explicitly skip tests for inapplicable variant
iommufd/vdevice: Remove struct device reference from struct vdevice
iommufd: Destroy vdevice on idevice destroy
iommufd: Add a pre_destroy() op for objects
iommufd: Add iommufd_object_tombstone_user() helper
iommufd/viommu: Roll back to use iommufd_object_alloc() for vdevice
iommufd/selftest: Test reserved regions near ULONG_MAX
iommufd: Prevent ALIGN() overflow
iommu/tegra241-cmdqv: import IOMMUFD module namespace
iommufd: Do not allow _iommufd_object_alloc_ucmd if abort op is set
iommu/tegra241-cmdqv: Add IOMMU_VEVENTQ_TYPE_TEGRA241_CMDQV support
iommu/tegra241-cmdqv: Add user-space use support
iommu/tegra241-cmdqv: Do not statically map LVCMDQs
iommu/tegra241-cmdqv: Simplify deinit flow in tegra241_cmdqv_remove_vintf()
iommu/tegra241-cmdqv: Use request_threaded_irq
iommu/arm-smmu-v3-iommufd: Add hw_info to impl_ops
...
|
|
Pull rdma updates from Jason Gunthorpe:
- Various minor code cleanups and fixes for hns, iser, cxgb4, hfi1,
rxe, erdma, mana_ib
- Prefetch supprot for rxe ODP
- Remove memory window support from hns as new device FW is no longer
support it
- Remove qib, it is very old and obsolete now, Cornelis wishes to
restructure the hfi1/qib shared layer
- Fix a race in destroying CQs where we can still end up with work
running because the work is cancled before the driver stops
triggering it
- Improve interaction with namespaces:
* Follow the devlink namespace for newly spawned RDMA devices
* Create iopoib net devces in the parent IB device's namespace
* Allow CAP_NET_RAW checks to pass in user namespaces
- A new flow control scheme for IB MADs to try and avoid queue
overflows in the network
- Fix 2G message sizes in bnxt_re
- Optimize mkey layout for mlx5 DMABUF
- New "DMA Handle" concept to allow controlling PCI TPH and steering
tags
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (71 commits)
RDMA/siw: Change maintainer email address
RDMA/mana_ib: add support of multiple ports
RDMA/mlx5: Refactor optional counters steering code
RDMA/mlx5: Add DMAH support for reg_user_mr/reg_user_dmabuf_mr
IB: Extend UVERBS_METHOD_REG_MR to get DMAH
RDMA/mlx5: Add DMAH object support
RDMA/core: Introduce a DMAH object and its alloc/free APIs
IB/core: Add UVERBS_METHOD_REG_MR on the MR object
net/mlx5: Add support for device steering tag
net/mlx5: Expose IFC bits for TPH
PCI/TPH: Expose pcie_tph_get_st_table_size()
RDMA/mlx5: Fix incorrect MKEY masking
RDMA/mlx5: Fix returned type from _mlx5r_umr_zap_mkey()
RDMA/mlx5: remove redundant check on err on return expression
RDMA/mana_ib: add additional port counters
RDMA/mana_ib: Fix DSCP value in modify QP
RDMA/efa: Add CQ with external memory support
RDMA/core: Add umem "is_contiguous" and "start_dma_addr" helpers
RDMA/uverbs: Add a common way to create CQ with umem
RDMA/mlx5: Optimize DMABUF mkey page size
...
|
|
Pull SCSI updates from James Bottomley:
"Smaller set of driver updates than usual (ufs, lpfc, mpi3mr).
The rest (including the core file changes) are doc updates and some
minor bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (49 commits)
scsi: libiscsi: Initialize iscsi_conn->dd_data only if memory is allocated
scsi: scsi_transport_fc: Add comments to describe added 'rport' parameter
scsi: bfa: Double-free fix
scsi: isci: Fix dma_unmap_sg() nents value
scsi: mvsas: Fix dma_unmap_sg() nents value
scsi: elx: efct: Fix dma_unmap_sg() nents value
scsi: scsi_transport_fc: Change to use per-rport devloss_work_q
scsi: ufs: exynos: Fix programming of HCI_UTRL_NEXUS_TYPE
scsi: core: Fix kernel doc for scsi_track_queue_full()
scsi: ibmvscsi_tgt: Fix dma_unmap_sg() nents value
scsi: ibmvscsi_tgt: Fix typo in comment
scsi: mpi3mr: Update driver version to 8.14.0.5.50
scsi: mpi3mr: Serialize admin queue BAR writes on 32-bit systems
scsi: mpi3mr: Drop unnecessary volatile from __iomem pointers
scsi: mpi3mr: Fix race between config read submit and interrupt completion
scsi: ufs: ufs-qcom: Enable QUnipro Internal Clock Gating
scsi: ufs: core: Add ufshcd_dme_rmw() to modify DME attributes
scsi: ufs: ufs-qcom: Update esi_vec_mask for HW major version >= 6
scsi: core: Use scsi_cmd_priv() instead of open-coding it
scsi: qla2xxx: Remove firmware URL
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Improvements & Fixes:
- A fix for QCOM Flash to prevent incorrect register access when the
driver is re-bound. This is solved by duplicating a static register
array during the probe function, which prevents register addresses
from being miscalculated after multiple binds
- The LP50xx driver now correctly handles the 'reg' property in
device tree child nodes to ensure the multi_index is set correctly.
This prevents issues where LEDs could be controlled incorrectly if
the device tree nodes were processed in a different order. An error
is returned if the reg property is missing or out of range
- Add a Kconfig dependency on between TPS6131x and
V4L2_FLASH_LED_CLASS to prevent a build failure when the driver is
built-in and the V4L2 flash infrastructure is a loadable module
- Fix a potential buffer overflow warning in PCA955x reported by
older GCC versions by using a more precise format specifier when
creating the default LED label.
Cleanups & Refactoring:
- Correct the MAINTAINERS file entry for the TPS6131X flash LED
driver to point to the correct device tree binding file name
- Fix a comment in the Flash Class for the flash_timeout setter to
"flash timeout" from "flash duration" for accuracy
- The of_led_get() function is no longer exported as it has no users
outside of its own module.
Removals:
- Revert the commit to configure LED blink intervals for hardware
offload in the Netdev Trigger. This change was found to break
existing PHY drivers by putting their LEDs into a permanent,
unconditional blinking state.
Device Tree Bindings Updates:
- Update the binding for LP50xx to document that the child reg
property is the index within the LED bank. The example was also
updated to use correct values
- Update the JNCP5623 binding to add 0x39 as a valid I2C address, as
it is used by the NCP5623C variant"
* tag 'leds-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds:
dt-bindings: leds: ncp5623: Add 0x39 as a valid I2C address
Revert "leds: trigger: netdev: Configure LED blink interval for HW offload"
leds: pca955x: Avoid potential overflow when filling default_label (take 2)
leds: Unexport of_led_get()
leds: tps6131x: Add V4L2_FLASH_LED_CLASS dependency
dt-bindings: leds: lp50xx: Document child reg, fix example
leds: leds-lp50xx: Handle reg to get correct multi_index
leds: led-class-flash:: Fix flash_timeout comment
MAINTAINERS: Adjust file entry in TPS6131X FLASH LED DRIVER
leds: flash: leds-qcom-flash: Fix registry access after re-bind
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Support & Features:
- Add extensive support for the Analog Devices ADP5589 I/O expander,
including core MFD, GPIO, PWM, and a new keypad matrix input
driver. This also adds support for handling various events
including GPI, keypad, reset and unlock ev ents
- Add support for the TI TPS652G1 PMIC, a stripped-down version of
the TPS65224, including core MFD, PFSM, pinctrl, and GPIO support
- Add support for the Apple Silicon System Management Controller
(SMC), including the core MFD driver which handles the RTKit-based
protocol, a new GPIO driver for PMU GPIOs, and a new
reboot/power-off driver.
Improvements & Fixes:
- Dynamically add ADP5585 sub-devices based on device tree properties
- Move ADP5585 oscillator control from the child PWM driver to the
main MFD driver to better handle shared resources
- Add support for a hardware reset pin and VDD regulator to the
ADP5585 driver
- Update the TPS65219 MFD cell's GPIO compatible string for the
TPS65214 to reflect hardware capabilities correctly
- Separate the ChromeOS EC charge-control probing from the USB-PD
subsystem, allowing it to probe independently based on the
dedicated EC_FEATURE_CHARGER
- Fix an interrupt naming typo in the MT6370 driver
- Fix RK806 PMIC reset behavior by allowing the reset mode to be
customized via a new device tree property
- Fix AXP20X regulator cell ID conflicts for secondary PMICs on
boards without an IRQ line connected
- Fix MT6397 keypad sub-device creation to use specific names instead
of a generic one, ensuring correct driver binding
- Fix a build warning in the stm32-timers driver by adding a missing
include for export.h.
Cleanups & Refactoring:
- Refactor the ADP5585 driver to simplify how regmap defaults are
handled, making it easier to add new chip variants
- Introduce per-chip register map structures for the ADP5585/ADP5589
family to handle differences between the devices
- Convert several drivers to use dev_fwnode() instead of
of_fwnode_handle()
- Make various static structures const in the cs40l50, rohm-bd71828,
tps65219, and twl6040 drivers
- Remove redundant pm_runtime_mark_last_busy() calls from several
drivers
- Alphabetize Kconfig entries for Cirrus Logic and Maxim drivers
- Remove unused fields from the 'tps65219' struct
- Update several MFD-related headers to follow the 'Include What You
Use' (IWYU) principle.
Removals:
- Remove the old, platform-data-based adp5589-keys input driver,
which is now superseded by the new MFD-based adp5585-keys driver
- Remove the unused twl6030_mmc_card_detect() functions and
associated header declarations
- Remove the now unused pcf50633/core.h header file
- Remove the fsl,imx8qxp-csr device tree binding, which was being
used incorrectly.
Device Tree Bindings Updates:
- Add support for the Analog Devices ADP5589 I/O expander to the
adi,adp5585.yaml binding
- Add new properties to the adi,adp5585.yaml binding for input
events, including keypad pins, unlock events, and reset events
- Add a reset-gpios property to the adi,adp5585.yaml binding
- Add the TI TPS652G1 PMIC to the ti,tps6594.yaml binding
- Add new bindings for the Apple Mac System Management Controller
(SMC) and its sub-devices: apple,smc.yaml, apple,smc-gpio.yaml, and
apple,smc-reboot.yaml
- Convert the Freescale MXS LRADC binding (mxs-lradc) to YAML schema
format
- Convert and combine the NXP LPC1850 CREG, DMAMUX, and USB OTG PHY
bindings into a single YAML schema file
- Convert the TI TPS65910 binding to YAML schema format
- Add a comment to the samsung,s2mps11.yaml binding to clarify the
use of 'oneOf' for interrupt properties
- Add the rockchip,reset-mode property to the rockchip,rk806.yaml
binding to allow customization of the PMIC's reset behavior"
* tag 'mfd-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (28 commits)
mfd: dt-bindings: Convert TPS65910 to DT schema
mfd: Minor Cirrus/Maxim Kconfig order fixes
mfd: Remove redundant pm_runtime_mark_last_busy() calls
mfd: mt6397: Do not use generic name for keypad sub-devices
mfd: axp20x: Set explicit ID for regulator cell if no IRQ line is present
mfd: mt6370: Fix the interrupt naming typo
mfd: rk8xx-core: Allow to customize RK806 reset mode
dt-bindings: mfd: rk806: Allow to customize PMIC reset mode
mfd: syscon: atmel-smc: Don't use "proxy" headers
mfd: madera: Don't use "proxy" headers
mfd: wm8350-core: Don't use "proxy" headers
dt-bindings: mfd: samsung,s2mps11: Add comment about interrupts properties
mfd: davinci_voicecodec: Don't use "proxy" headers
mfd: pcf50633: Remove the header file core.h
mfd: tps65219: Remove another unused field from 'struct tps65219'
mfd: tps65219: Remove an unused field from 'struct tps65219'
mfd: tps65219: Constify struct regmap_irq_sub_irq_map and tps65219_chip_data
mfd: rohm-bd71828: Constify some structures
dt-bindings: mfd: fsl,imx8qxp-csr: Remove binding documentation
mfd: axp20x: Set explicit ID for AXP313 regulator
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- DT updates for ralink, mobileye and atheros/qualcomm
- Clean up of mc146818 usage
- Speed up delay calibration for CPS
- Other cleanups and fixes
* tag 'mips_6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (50 commits)
MIPS: Don't use %pK through printk
MIPS: Update Joshua Kinard's e-mail address
MIPS: mobileye: dts: eyeq5,eyeq6h: rename the emmc controller
MIPS: mm: tlb-r4k: Uniquify TLB entries on init
MIPS: SGI-IP27: Delete an unnecessary check before kfree() in hub_domain_free()
mips/malta,loongson2ef: use generic mc146818_get_time function
mips: remove redundant macro mc146818_decode_year
mips/mach-rm: remove custom mc146818rtc.h file
mips: remove unused function mc146818_set_rtc_mmss
MIPS: CPS: Optimise delay CPU calibration for SMP
MIPS: CPS: Improve mips_cps_first_online_in_cluster()
MIPS: disable MMID when not supported by the hardware
MIPS: eyeq5_defconfig: add I2C subsystem, driver and temp sensor driver
MIPS: eyeq5_defconfig: add GPIO subsystem & driver
MIPS: mobileye: eyeq5: add two GPIO bank nodes
MIPS: mobileye: eyeq5: add evaluation board I2C temp sensor
MIPS: mobileye: eyeq5: add 5 I2C controller nodes
MIPS: eyeq5_defconfig: Update for v6.16-rc1
MIPS: vpe-mt: add missing prototypes for vpe_{alloc,start,stop,free}
mips: boot: use 'targets' instead of extra-y in Makefile
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBIFS:
- No longer use write_cache_pages()
UBI:
- Remove an unused function"
* tag 'ubifs-for-linus-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: stop using write_cache_pages
mtd: ubi: Remove unused ubi_flush
|
|
* Raw NAND changes:
Various controller drivers received minor fixes like DMA mapping checks,
better timing derivations or bitflip statistics.
It has also been discovered that some Hynix NAND flashes were not
supporting read-retries, which is not properly supported.
* SPI NAND changes:
In order to support high-speed modes, certain chips need extra
configuration like adding more dummy cycles. This is now possible,
especially on Winbond chips.
Aside from that, Gigadevice gets support for a new chip (GD5F1GM9).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SPI NOR changes for 6.17
Notable changes:
- Fix exiting 4-byte addressing on Infineon SEMPER flashes. These
flashes do not support the standard EX4B opcode (E9h), and use a
vendor-specific opcode (B8h) instead.
- Fix unlocking of flashes that are write-protected at power-on. This
was caused by using an uninitialized mtd_info in
spi_nor_try_unlock_all().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Allow hash drivers without fallbacks (e.g., hardware key)
Algorithms:
- Add hmac hardware key support (phmac) on s390
- Re-enable sha384 in FIPS mode
- Disable sha1 in FIPS mode
- Convert zstd to acomp
Drivers:
- Lower priority of qat skcipher and aead
- Convert aspeed to partial block API
- Add iMX8QXP support in caam
- Add rate limiting support for GEN6 devices in qat
- Enable telemetry for GEN6 devices in qat
- Implement full backlog mode for hisilicon/sec2"
* tag 'v6.17-p1' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (116 commits)
crypto: keembay - Use min() to simplify ocs_create_linked_list_from_sg()
crypto: hisilicon/hpre - fix dma unmap sequence
crypto: qat - make adf_dev_autoreset() static
crypto: ccp - reduce stack usage in ccp_run_aes_gcm_cmd
crypto: qat - refactor ring-related debug functions
crypto: qat - fix seq_file position update in adf_ring_next()
crypto: qat - fix DMA direction for compression on GEN2 devices
crypto: jitter - replace ARRAY_SIZE definition with header include
crypto: engine - remove {prepare,unprepare}_crypt_hardware callbacks
crypto: engine - remove request batching support
crypto: qat - flush misc workqueue during device shutdown
crypto: qat - enable rate limiting feature for GEN6 devices
crypto: qat - add compression slice count for rate limiting
crypto: qat - add get_svc_slice_cnt() in device data structure
crypto: qat - add adf_rl_get_num_svc_aes() in rate limiting
crypto: qat - relocate service related functions
crypto: qat - consolidate service enums
crypto: qat - add decompression service for rate limiting
crypto: qat - validate service in rate limiting sysfs api
crypto: hisilicon/sec2 - implement full backlog mode for sec
...
|
|
Resolve conflicts with i.MX95 changes 88768d6f8c13 ("clk:
imx95-blk-ctl: Rename lvds and displaymix csr blk") in clk-imx
and aacc875a448d ("clk: imx: Fix an out-of-bounds access in
dispmix_csr_clk_dev_data") in clk-fixes.
* clk-fixes:
clk: sunxi-ng: v3s: Fix TCON clock parents
clk: sunxi-ng: v3s: Fix CSI1 MCLK clock name
clk: sunxi-ng: v3s: Fix CSI SCLK clock name
dt-bindings: clock: mediatek: Add #reset-cells property for MT8188
clk: imx: Fix an out-of-bounds access in dispmix_csr_clk_dev_data
clk: scmi: Handle case where child clocks are initialized before their parents
clk: sunxi-ng: a523: Mark MBUS clock as critical
|
|
dm-thin obviously can pass through inline crypto support.
Signed-off-by: LongPing Wei <weilongping@oppo.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
In commit 4cc96131afce ("dm: move request-based code out to dm-rq.[hc]")
we have a note: "DM targets should _never_ include dm-core.h!". And it
is not used in any DM targets except dm-raid now, so let's remove it
from dm-raid for consistency, also use special helpers instead of
accessing dm_table and mapper_device fields directly. This change is
merely a cleanup and should not affect functionality.
Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Reviewed-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
There's no need to call need_resched() because cond_resched() will do
nothing if need_resched() returns false.
Reviewed-by: Matthew Sakai <msakai@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Fix Smatch-detected error:
drivers/md/dm-zoned-target.c:1073 dmz_iterate_devices()
error: uninitialized symbol 'r'.
Smatch detects a possible use of the uninitialized variable 'r' in
dmz_iterate_devices() because if dmz->nr_ddevs is zero, the loop is
skipped and 'r' is returned without being set, leading to undefined
behavior.
Initialize 'r' to 0 before the loop. This ensures that if there are no
devices to iterate over, the function still returns a defined value.
Signed-off-by: Purva Yeshi <purvayeshi550@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
The support for asynchronous hashes in dm-verity has outlived its
usefulness. It adds significant code complexity and opportunity for
bugs. I don't know of anyone using it in practice. (The original
submitter of the code possibly was, but that was 8 years ago.) Data I
recently collected for en/decryption shows that using off-CPU crypto
"accelerators" is consistently much slower than the CPU
(https://lore.kernel.org/r/20250704070322.20692-1-ebiggers@kernel.org/),
even on CPUs that lack dedicated cryptographic instructions. Similar
results are likely to be seen for hashing.
I already removed support for asynchronous hashes from fsverity two
years ago, and no one ever complained.
Moreover, neither dm-verity, fsverity, nor fscrypt has ever actually
used the asynchronous crypto algorithms in a truly asynchronous manner.
The lack of interest in such optimizations provides further evidence
that it's only the CPU-based crypto that actually matters.
Historically, it's also been common for people to forget to enable the
optimized SHA-256 code, which could contribute to an off-CPU crypto
engine being perceived as more useful than it really is. In 6.16 I
fixed that: the optimized SHA-256 code is now enabled by default.
Therefore, let's drop the support for asynchronous hashes in dm-verity.
Tested with verity-compat-test.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Pull drm updates from Dave Airlie:
"Highlights:
- Intel xe enable Panthor Lake, started adding WildCat Lake
- amdgpu has a bunch of reset improvments along with the usual IP
updates
- msm got VM_BIND support which is important for vulkan sparse memory
- more drm_panic users
- gpusvm common code to handle a bunch of core SVM work outside
drivers.
Detail summary:
Changes outside drm subdirectory:
- 'shrink_shmem_memory()' for better shmem/hibernate interaction
- Rust support infrastructure:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
- mtd driver for Intel GPU non-volatile storage
- i2c designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support"
* tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel: (1479 commits)
drm/tidss: oldi: convert to devm_drm_bridge_alloc() API
drm/tidss: encoder: convert to devm_drm_bridge_alloc()
drm/amdgpu: move reset support type checks into the caller
drm/amdgpu/sdma7: re-emit unprocessed state on ring reset
drm/amdgpu/sdma6: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5.2: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5: re-emit unprocessed state on ring reset
drm/amdgpu/gfx12: re-emit unprocessed state on ring reset
drm/amdgpu/gfx11: re-emit unprocessed state on ring reset
drm/amdgpu/gfx10: re-emit unprocessed state on ring reset
drm/amdgpu/gfx9.4.3: re-emit unprocessed state on kcq reset
drm/amdgpu/gfx9: re-emit unprocessed state on kcq reset
drm/amdgpu: Add WARN_ON to the resource clear function
drm/amd/pm: Use cached metrics data on SMUv13.0.6
drm/amd/pm: Use cached data for min/max clocks
gpu: nova-core: fix bounds check in PmuLookupTableEntry::new
drm/amdgpu: Replace HQD terminology with slots naming
drm/amdgpu: Add user queue instance count in HW IP info
drm/amd/amdgpu: Add helper functions for isp buffers
drm/amd/amdgpu: Initialize swnode for ISP MFD device
...
|
|
LKP found a random config which failed to build because IO accessors
were not defined:
In file included from drivers/i3c/master.c:21:
drivers/i3c/internals.h: In function 'i3c_writel_fifo':
>> drivers/i3c/internals.h:35:9: error: implicit declaration of function 'writesl' [-Werror=implicit-function-declaration]
Add the proper header to where the IO accessors are used.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507150208.BZDzzJ5E-lkp@intel.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250717120046.9022-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Host driver for GICv5, the next generation interrupt controller for
arm64, including support for interrupt routing, MSIs, interrupt
translation and wired interrupts
- Use FEAT_GCIE_LEGACY on GICv5 systems to virtualize GICv3 VMs on
GICv5 hardware, leveraging the legacy VGIC interface
- Userspace control of the 'nASSGIcap' GICv3 feature, allowing
userspace to disable support for SGIs w/o an active state on
hardware that previously advertised it unconditionally
- Map supporting endpoints with cacheable memory attributes on
systems with FEAT_S2FWB and DIC where KVM no longer needs to
perform cache maintenance on the address range
- Nested support for FEAT_RAS and FEAT_DoubleFault2, allowing the
guest hypervisor to inject external aborts into an L2 VM and take
traps of masked external aborts to the hypervisor
- Convert more system register sanitization to the config-driven
implementation
- Fixes to the visibility of EL2 registers, namely making VGICv3
system registers accessible through the VGIC device instead of the
ONE_REG vCPU ioctls
- Various cleanups and minor fixes
LoongArch:
- Add stat information for in-kernel irqchip
- Add tracepoints for CPUCFG and CSR emulation exits
- Enhance in-kernel irqchip emulation
- Various cleanups
RISC-V:
- Enable ring-based dirty memory tracking
- Improve perf kvm stat to report interrupt events
- Delegate illegal instruction trap to VS-mode
- MMU improvements related to upcoming nested virtualization
s390x
- Fixes
x86:
- Add CONFIG_KVM_IOAPIC for x86 to allow disabling support for I/O
APIC, PIC, and PIT emulation at compile time
- Share device posted IRQ code between SVM and VMX and harden it
against bugs and runtime errors
- Use vcpu_idx, not vcpu_id, for GA log tag/metadata, to make lookups
O(1) instead of O(n)
- For MMIO stale data mitigation, track whether or not a vCPU has
access to (host) MMIO based on whether the page tables have MMIO
pfns mapped; using VFIO is prone to false negatives
- Rework the MSR interception code so that the SVM and VMX APIs are
more or less identical
- Recalculate all MSR intercepts from scratch on MSR filter changes,
instead of maintaining shadow bitmaps
- Advertise support for LKGS (Load Kernel GS base), a new instruction
that's loosely related to FRED, but is supported and enumerated
independently
- Fix a user-triggerable WARN that syzkaller found by setting the
vCPU in INIT_RECEIVED state (aka wait-for-SIPI), and then putting
the vCPU into VMX Root Mode (post-VMXON). Trying to detect every
possible path leading to architecturally forbidden states is hard
and even risks breaking userspace (if it goes from valid to valid
state but passes through invalid states), so just wait until
KVM_RUN to detect that the vCPU state isn't allowed
- Add KVM_X86_DISABLE_EXITS_APERFMPERF to allow disabling
interception of APERF/MPERF reads, so that a "properly" configured
VM can access APERF/MPERF. This has many caveats (APERF/MPERF
cannot be zeroed on vCPU creation or saved/restored on suspend and
resume, or preserved over thread migration let alone VM migration)
but can be useful whenever you're interested in letting Linux
guests see the effective physical CPU frequency in /proc/cpuinfo
- Reject KVM_SET_TSC_KHZ for vm file descriptors if vCPUs have been
created, as there's no known use case for changing the default
frequency for other VM types and it goes counter to the very reason
why the ioctl was added to the vm file descriptor. And also, there
would be no way to make it work for confidential VMs with a
"secure" TSC, so kill two birds with one stone
- Dynamically allocation the shadow MMU's hashed page list, and defer
allocating the hashed list until it's actually needed (the TDP MMU
doesn't use the list)
- Extract many of KVM's helpers for accessing architectural local
APIC state to common x86 so that they can be shared by guest-side
code for Secure AVIC
- Various cleanups and fixes
x86 (Intel):
- Preserve the host's DEBUGCTL.FREEZE_IN_SMM when running the guest.
Failure to honor FREEZE_IN_SMM can leak host state into guests
- Explicitly check vmcs12.GUEST_DEBUGCTL on nested VM-Enter to
prevent L1 from running L2 with features that KVM doesn't support,
e.g. BTF
x86 (AMD):
- WARN and reject loading kvm-amd.ko instead of panicking the kernel
if the nested SVM MSRPM offsets tracker can't handle an MSR (which
is pretty much a static condition and therefore should never
happen, but still)
- Fix a variety of flaws and bugs in the AVIC device posted IRQ code
- Inhibit AVIC if a vCPU's ID is too big (relative to what hardware
supports) instead of rejecting vCPU creation
- Extend enable_ipiv module param support to SVM, by simply leaving
IsRunning clear in the vCPU's physical ID table entry
- Disable IPI virtualization, via enable_ipiv, if the CPU is affected
by erratum #1235, to allow (safely) enabling AVIC on such CPUs
- Request GA Log interrupts if and only if the target vCPU is
blocking, i.e. only if KVM needs a notification in order to wake
the vCPU
- Intercept SPEC_CTRL on AMD if the MSR shouldn't exist according to
the vCPU's CPUID model
- Accept any SNP policy that is accepted by the firmware with respect
to SMT and single-socket restrictions. An incompatible policy
doesn't put the kernel at risk in any way, so there's no reason for
KVM to care
- Drop a superfluous WBINVD (on all CPUs!) when destroying a VM and
use WBNOINVD instead of WBINVD when possible for SEV cache
maintenance
- When reclaiming memory from an SEV guest, only do cache flushes on
CPUs that have ever run a vCPU for the guest, i.e. don't flush the
caches for CPUs that can't possibly have cache lines with dirty,
encrypted data
Generic:
- Rework irqbypass to track/match producers and consumers via an
xarray instead of a linked list. Using a linked list leads to
O(n^2) insertion times, which is hugely problematic for use cases
that create large numbers of VMs. Such use cases typically don't
actually use irqbypass, but eliminating the pointless registration
is a future problem to solve as it likely requires new uAPI
- Track irqbypass's "token" as "struct eventfd_ctx *" instead of a
"void *", to avoid making a simple concept unnecessarily difficult
to understand
- Decouple device posted IRQs from VFIO device assignment, as binding
a VM to a VFIO group is not a requirement for enabling device
posted IRQs
- Clean up and document/comment the irqfd assignment code
- Disallow binding multiple irqfds to an eventfd with a priority
waiter, i.e. ensure an eventfd is bound to at most one irqfd
through the entire host, and add a selftest to verify eventfd:irqfd
bindings are globally unique
- Add a tracepoint for KVM_SET_MEMORY_ATTRIBUTES to help debug issues
related to private <=> shared memory conversions
- Drop guest_memfd's .getattr() implementation as the VFS layer will
call generic_fillattr() if inode_operations.getattr is NULL
- Fix issues with dirty ring harvesting where KVM doesn't bound the
processing of entries in any way, which allows userspace to keep
KVM in a tight loop indefinitely
- Kill off kvm_arch_{start,end}_assignment() and x86's associated
tracking, now that KVM no longer uses assigned_device_count as a
heuristic for either irqbypass usage or MDS mitigation
Selftests:
- Fix a comment typo
- Verify KVM is loaded when getting any KVM module param so that
attempting to run a selftest without kvm.ko loaded results in a
SKIP message about KVM not being loaded/enabled (versus some random
parameter not existing)
- Skip tests that hit EACCES when attempting to access a file, and
print a "Root required?" help message. In most cases, the test just
needs to be run with elevated permissions"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (340 commits)
Documentation: KVM: Use unordered list for pre-init VGIC registers
RISC-V: KVM: Avoid re-acquiring memslot in kvm_riscv_gstage_map()
RISC-V: KVM: Use find_vma_intersection() to search for intersecting VMAs
RISC-V: perf/kvm: Add reporting of interrupt events
RISC-V: KVM: Enable ring-based dirty memory tracking
RISC-V: KVM: Fix inclusion of Smnpm in the guest ISA bitmap
RISC-V: KVM: Delegate illegal instruction fault to VS mode
RISC-V: KVM: Pass VMID as parameter to kvm_riscv_hfence_xyz() APIs
RISC-V: KVM: Factor-out g-stage page table management
RISC-V: KVM: Add vmid field to struct kvm_riscv_hfence
RISC-V: KVM: Introduce struct kvm_gstage_mapping
RISC-V: KVM: Factor-out MMU related declarations into separate headers
RISC-V: KVM: Use ncsr_xyz() in kvm_riscv_vcpu_trap_redirect()
RISC-V: KVM: Implement kvm_arch_flush_remote_tlbs_range()
RISC-V: KVM: Don't flush TLB when PTE is unchanged
RISC-V: KVM: Replace KVM_REQ_HFENCE_GVMA_VMID_ALL with KVM_REQ_TLB_FLUSH
RISC-V: KVM: Rename and move kvm_riscv_local_tlb_sanitize()
RISC-V: KVM: Drop the return value of kvm_riscv_vcpu_aia_init()
RISC-V: KVM: Check kvm_riscv_vcpu_alloc_vector_context() return value
KVM: arm64: selftests: Add FEAT_RAS EL2 registers to get-reg-list
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- fix for a UAF in the xen gntdev-dmabuf driver
- fix in the xen netfront driver avoiding spurious interrupts
- fix in the gntdev driver avoiding a large stack allocation
- cleanup removing some dead code
- build warning fix
- cleanup of the sysfs code in the xen-pciback driver
* tag 'for-linus-6.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/netfront: Fix TX response spurious interrupts
xen/gntdev: remove struct gntdev_copy_batch from stack
xen: fix UAF in dmabuf_exp_from_pages()
xen: Remove some deadcode (x)
xen-pciback: Replace scnprintf() with sysfs_emit_at()
xen/xenbus: fix W=1 build warning in xenbus_va_dev_error function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracepoint cleanup from Steven Rostedt:
"Remove or hide unused tracepoints
Tracepoints take up memory (around 5K per tracepoint) even when they
are unused. Changes are being made to detect when a tracepoint is
defined but unused and a warning is shown at build. But those changes
are not yet ready for inclusion.
- Fix some of the unused tracepoints that it detected
Some tracepoints were removed and others were hidden by config
settings to match the config settings of where they are
instantiated. Some tracepoints were moved into architecture
specific code as only one architecture used them.
- Call the ftrace_test_filter tracepoint in an unreachable if
statement
The ftrace_test_filter tracepoint which is defined when ftrace
selftests are configured and is used to test the filter logic, but
the tracepoint is not actually called. It is put into an if
statement to not have it get compiled out, but also not warn for
not being used"
* tag 'trace-unused-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: sched: Hide numa events under CONFIG_NUMA_BALANCING
powerpc/thp: tracing: Hide hugepage events under CONFIG_PPC_BOOK3S_64
tracing: Call trace_ftrace_test_filter() for the event
tracing: arm: arm64: Hide trace events ipi_raise, ipi_entry and ipi_exit
binder: Remove unused binder lock events
PM: tracing: Hide power_domain_target event under ARCH_OMAP2PLUS
PM: tracing: Hide device_pm_callback events under PM_SLEEP
PM: tracing: Hide psci_domain_idle events under ARM_PSCI_CPUIDLE
PM: cpufreq: powernv/tracing: Move powernv_throttle trace event
alarmtimer: Hide alarmtimer_suspend event when RTC_CLASS is not configured
tracing, AER: Hide PCIe AER event when PCIEAER is not configured
|
|
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704075417.3218742-1-sakari.ailus@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250704075416.3218647-1-sakari.ailus@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In a private write transfer, the driver pre-fills the FIFO to work around
the FIFO_EMPTY quirk. However, if an IBIWON event occurs, the hardware
emits a NACK and the driver initiates a retry. During the retry, driver
attempts to pre-fill the FIFO again if there is remaining data, but since
the FIFO is already full, this leads to data loss.
Check available space in FIFO to prevent overflow.
Fixes: 4008a74e0f9b ("i3c: master: svc: Fix npcm845 FIFO empty issue")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Link: https://lore.kernel.org/r/20250730003719.1825593-1-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add a basic driver for the I3C controller found in Renesas RZ/G3S and
G3E SoCs. Support I3C pure busses (tested with two targets) and mixed
busses (two I3C devices plus various I2C targets). DAA and communication
with temperature sensors worked reliably at various speeds.
Missing features such as IBI, HotJoin, and target mode will be added
incrementally.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250724094146.6443-5-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Align existing defines to follow the consistent pattern:
I3C_BUS_<PARAM>_<MAX|MIN|TYP>_<UNIT>. Prepare the codebase for adding
new parameters and help avoid duplication.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250724094146.6443-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The two clocks, driver is getting, are not being disabled/re-enabled
during runtime of the device. Eliminate one variable in state struct,
all error paths and a lot of code from probe() and remove() by using
devm_clk_get_enabled().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250713152411.74917-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Sphinx reports indentation warning on i3c_device_do_priv_xfers() return
value list:
Documentation/driver-api/i3c/device-driver-api:9: ./drivers/i3c/device.c:31: ERROR: Unexpected indentation. [docutils]
Format the list as bullet list to fix the warning.
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250702040424.18577-1-bagasdotme@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use common inline i3c_writel_fifo()/i3c_readl_fifo() methods to
simplify code since the FIFO of controller is a 32bit width.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-3-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use common inline i3c_writel_fifo()/i3c_readl_fifo() methods to
simplify code since the FIFO of controller is a 32bit width.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-2-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The I3C abstraction expects u8 buffers, but some controllers operate with
a 32-bit bus width FIFO and cannot flag valid bytes individually. To avoid
reading or writing outside the buffer bounds, use 32-bit accesses where
possible and apply memcpy for any remaining bytes
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Suggested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-1-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
CSC is not accessible by VF drivers, so disable its support flag on VF
to prevent further initialization attempts.
Fixes: e02cea83d32d ("drm/xe/gsc: add Battlemage support")
Signed-off-by: Lukasz Laguna <lukasz.laguna@intel.com>
Cc: Alexander Usyskin <alexander.usyskin@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://lore.kernel.org/r/20250729123437.5933-1-lukasz.laguna@intel.com
(cherry picked from commit 552dbba1caaf0cb40ce961806d757615e26ec668)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Will Deacon:
"Core:
- Remove the 'pgsize_bitmap' member from 'struct iommu_ops'
- Convert the x86 drivers over to msi_create_parent_irq_domain()
AMD-Vi:
- Add support for examining driver/device internals via debugfs
- Add support for "HATDis" to disable host translation when it is not
supported
- Add support for limiting the maximum host translation level based
on EFR[HATS]
Apple DART:
- Don't enable as built-in by default when ARCH_APPLE is selected
Arm SMMU:
- Devicetree bindings update for the Qualcomm SMMU in the "Milos" SoC
- Support for Qualcomm SM6115 MDSS parts
- Disable PRR on Qualcomm SM8250 as using these bits causes the
hypervisor to explode
Intel VT-d:
- Reorganize Intel VT-d to be ready for iommupt
- Optimize iotlb_sync_map for non-caching/non-RWBF modes
- Fix missed PASID in dev TLB invalidation in cache_tag_flush_all()
Mediatek:
- Fix build warnings when W=1
Samsung Exynos:
- Add support for reserved memory regions specified by the bootloader
TI OMAP:
- Use syscon_regmap_lookup_by_phandle_args() instead of parsing the
node manually
Misc:
- Cleanups and minor fixes across the board"
* tag 'iommu-updates-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (48 commits)
iommu/vt-d: Fix UAF on sva unbind with pending IOPFs
iommu/vt-d: Make iotlb_sync_map a static property of dmar_domain
dt-bindings: arm-smmu: Remove sdm845-cheza specific entry
iommu/amd: Fix geometry.aperture_end for V2 tables
iommu/amd: Wrap debugfs ABI testing symbols snippets in literal code blocks
iommu/amd: Add documentation for AMD IOMMU debugfs support
iommu/amd: Add debugfs support to dump IRT Table
iommu/amd: Add debugfs support to dump device table
iommu/amd: Add support for device id user input
iommu/amd: Add debugfs support to dump IOMMU command buffer
iommu/amd: Add debugfs support to dump IOMMU Capability registers
iommu/amd: Add debugfs support to dump IOMMU MMIO registers
iommu/amd: Refactor AMD IOMMU debugfs initial setup
dt-bindings: arm-smmu: document the support on Milos
iommu/exynos: add support for reserved regions
iommu/arm-smmu: disable PRR on SM8250
iommu/arm-smmu-v3: Revert vmaster in the error path
iommu/io-pgtable-arm: Remove unused macro iopte_prot
iommu/arm-smmu-qcom: Add SM6115 MDSS compatible
iommu/qcom: Fix pgsize_bitmap
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Pull bpf updates from Alexei Starovoitov:
- Remove usermode driver (UMD) framework (Thomas Weißschuh)
- Introduce Strongly Connected Component (SCC) in the verifier to
detect loops and refine register liveness (Eduard Zingerman)
- Allow 'void *' cast using bpf_rdonly_cast() and corresponding
'__arg_untrusted' for global function parameters (Eduard Zingerman)
- Improve precision for BPF_ADD and BPF_SUB operations in the verifier
(Harishankar Vishwanathan)
- Teach the verifier that constant pointer to a map cannot be NULL
(Ihor Solodrai)
- Introduce BPF streams for error reporting of various conditions
detected by BPF runtime (Kumar Kartikeya Dwivedi)
- Teach the verifier to insert runtime speculation barrier (lfence on
x86) to mitigate speculative execution instead of rejecting the
programs (Luis Gerhorst)
- Various improvements for 'veristat' (Mykyta Yatsenko)
- For CONFIG_DEBUG_KERNEL config warn on internal verifier errors to
improve bug detection by syzbot (Paul Chaignon)
- Support BPF private stack on arm64 (Puranjay Mohan)
- Introduce bpf_cgroup_read_xattr() kfunc to read xattr of cgroup's
node (Song Liu)
- Introduce kfuncs for read-only string opreations (Viktor Malik)
- Implement show_fdinfo() for bpf_links (Tao Chen)
- Reduce verifier's stack consumption (Yonghong Song)
- Implement mprog API for cgroup-bpf programs (Yonghong Song)
* tag 'bpf-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (192 commits)
selftests/bpf: Migrate fexit_noreturns case into tracing_failure test suite
selftests/bpf: Add selftest for attaching tracing programs to functions in deny list
bpf: Add log for attaching tracing programs to functions in deny list
bpf: Show precise rejected function when attaching fexit/fmod_ret to __noreturn functions
bpf: Fix various typos in verifier.c comments
bpf: Add third round of bounds deduction
selftests/bpf: Test invariants on JSLT crossing sign
selftests/bpf: Test cross-sign 64bits range refinement
selftests/bpf: Update reg_bound range refinement logic
bpf: Improve bounds when s64 crosses sign boundary
bpf: Simplify bounds refinement from s32
selftests/bpf: Enable private stack tests for arm64
bpf, arm64: JIT support for private stack
bpf: Move bpf_jit_get_prog_name() to core.c
bpf, arm64: Fix fp initialization for exception boundary
umd: Remove usermode driver framework
bpf/preload: Don't select USERMODE_DRIVER
selftests/bpf: Fix test dynptr/test_dynptr_memset_xdp_chunks failure
selftests/bpf: Fix test dynptr/test_dynptr_copy_xdp failure
selftests/bpf: Increase xdp data size for arm64 64K page size
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
|
