| Age | Commit message (Collapse) | Author |
|---|
|
It is currently impossible to enable ipv6 forwarding on a per-interface
basis like in ipv4. To enable forwarding on an ipv6 interface we need to
enable it on all interfaces and disable it on the other interfaces using
a netfilter rule. This is especially cumbersome if you have lots of
interfaces and only want to enable forwarding on a few. According to the
sysctl docs [0] the `net.ipv6.conf.all.forwarding` enables forwarding
for all interfaces, while the interface-specific
`net.ipv6.conf.<interface>.forwarding` configures the interface
Host/Router configuration.
Introduce a new sysctl flag `force_forwarding`, which can be set on every
interface. The ip6_forwarding function will then check if the global
forwarding flag OR the force_forwarding flag is active and forward the
packet.
To preserve backwards-compatibility reset the flag (on all interfaces)
to 0 if the net.ipv6.conf.all.forwarding flag is set to 0.
Add a short selftest that checks if a packet gets forwarded with and
without `force_forwarding`.
[0]: https://www.kernel.org/doc/Documentation/networking/ip-sysctl.txt
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Gabriel Goller <g.goller@proxmox.com>
Link: https://patch.msgid.link/20250722081847.132632-1-g.goller@proxmox.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Gemalto Cinterion PLS83-W modem (cdc_ether) is emitting confusing link
up and down events when the WWAN interface is activated on the modem-side.
Interrupt URBs will in consecutive polls grab:
* Link Connected
* Link Disconnected
* Link Connected
Where the last Connected is then a stable link state.
When the system is under load this may cause the unlink_urbs() work in
__handle_link_change() to not complete before the next usbnet_link_change()
call turns the carrier on again, allowing rx_submit() to queue new SKBs.
In that event the URB queue is filled faster than it can drain, ending up
in a RCU stall:
rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 0-.... } 33108 jiffies s: 201 root: 0x1/.
rcu: blocking rcu_node structures (internal RCU debug):
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
Call trace:
arch_local_irq_enable+0x4/0x8
local_bh_enable+0x18/0x20
__netdev_alloc_skb+0x18c/0x1cc
rx_submit+0x68/0x1f8 [usbnet]
rx_alloc_submit+0x4c/0x74 [usbnet]
usbnet_bh+0x1d8/0x218 [usbnet]
usbnet_bh_tasklet+0x10/0x18 [usbnet]
tasklet_action_common+0xa8/0x110
tasklet_action+0x2c/0x34
handle_softirqs+0x2cc/0x3a0
__do_softirq+0x10/0x18
____do_softirq+0xc/0x14
call_on_irq_stack+0x24/0x34
do_softirq_own_stack+0x18/0x20
__irq_exit_rcu+0xa8/0xb8
irq_exit_rcu+0xc/0x30
el1_interrupt+0x34/0x48
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x68/0x6c
_raw_spin_unlock_irqrestore+0x38/0x48
xhci_urb_dequeue+0x1ac/0x45c [xhci_hcd]
unlink1+0xd4/0xdc [usbcore]
usb_hcd_unlink_urb+0x70/0xb0 [usbcore]
usb_unlink_urb+0x24/0x44 [usbcore]
unlink_urbs.constprop.0.isra.0+0x64/0xa8 [usbnet]
__handle_link_change+0x34/0x70 [usbnet]
usbnet_deferred_kevent+0x1c0/0x320 [usbnet]
process_scheduled_works+0x2d0/0x48c
worker_thread+0x150/0x1dc
kthread+0xd8/0xe8
ret_from_fork+0x10/0x20
Get around the problem by delaying the carrier on to the scheduled work.
This needs a new flag to keep track of the necessary action.
The carrier ok check cannot be removed as it remains required for the
LINK_RESET event flow.
Fixes: 4b49f58fff00 ("usbnet: handle link change")
Cc: stable@vger.kernel.org
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://patch.msgid.link/20250723102526.1305339-1-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This stems from a time when sets and nft_dynset resided in different kernel
modules. We can replace this with a direct call.
We could even remove both ->update and ->delete, given its only
supported by rhashtable, but on the off-chance we'll see runtime
add/delete for other types or a new set type keep that as-is for now.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Return the extension pointer instead of passing it as a function
argument to be filled in by the callee.
As-is, whenever false is returned, the extension pointer is not used.
For all set types, when true is returned, the extension pointer was set
to the matching element.
Only exception: nft_set_bitmap doesn't support extensions.
Return a pointer to a static const empty element extension container.
return false -> return NULL
return true -> return the elements' extension pointer.
This saves one function argument.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Introduce NFNL_HOOK_TYPE_NFT_FLOWTABLE to distinguish flowtable hooks
from base chain ones. Nested attributes are shared with the old NFTABLES
hook info type since they fit apart from their misleading name.
Old nftables in user space will ignore this new hook type and thus
continue to print flowtable hooks just like before, e.g.:
| family netdev {
| hook ingress device test0 {
| 0000000000 nf_flow_offload_ip_hook [nf_flow_table]
| }
| }
With this patch in place and support for the new hook info type, output
becomes more useful:
| family netdev {
| hook ingress device test0 {
| 0000000000 flowtable ip mytable myft [nf_flow_table]
| }
| }
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since commit 9e539c5b6d9c ("netfilter: nf_tables: disable expression
reduction infra") this is unused.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since commit 2173c519d5e9 ("audit: normalize NETFILTER_PKT")
these are unused, so can be removed.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When no logger is registered, nf_conntrack_log_invalid fails to log invalid
packets, leaving users unaware of actual invalid traffic. Improve this by
loading nf_log_syslog, similar to how 'iptables -I FORWARD 1 -m conntrack
--ctstate INVALID -j LOG' triggers it.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Zi Li <zi.li@linux.dev>
Signed-off-by: Lance Yang <lance.yang@linux.dev>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since nobody has used these EXT4_MB_HINT flags for ages,
let's remove them.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Link: https://patch.msgid.link/20250714130327.1830534-7-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The field 'reacting' in struct rv_monitor is set but never used. Delete it.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/a6c16f845d2f1a09c4d0934ab83f3cb14478a71d.1753378331.git.namcao@linutronix.de
Reviewed-by: Gabriele Monaco <gmonaco@redhat.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
rv_reactor has a reference counter to ensure it is not removed while
monitors are still using it.
However, this is futile, as __exit functions are not expected to fail and
will proceed normally despite rv_unregister_reactor() returning an error.
At the moment, reactors do not support being built as modules, therefore
they are never removed and the reference counters are not necessary.
If we support building RV reactors as modules in the future, kernel
module's centralized facilities such as try_module_get(), module_put() or
MODULE_SOFTDEP should be used instead of this custom implementation.
Remove this reference counter.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/bb946398436a5e17fb0f5b842ef3313c02291852.1753378331.git.namcao@linutronix.de
Reviewed-by: Gabriele Monaco <gmonaco@redhat.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Each struct rv_reactor has a unique struct rv_reactor_def associated with
it. struct rv_reactor is statically allocated, while struct rv_reactor_def
is dynamically allocated.
This makes the code more complicated than it should be:
- Lookup is required to get the associated rv_reactor_def from rv_reactor
- Dynamic memory allocation is required for rv_reactor_def. This is
harder to get right compared to static memory. For instance, there is
an existing mistake: rv_unregister_reactor() does not free the memory
allocated by rv_register_reactor(). This is fortunately not a real
memory leak problem as rv_unregister_reactor() is never called.
Simplify and merge rv_reactor_def into rv_reactor.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/71cb91c86cd40df5b8c492b788787f2a73c3eaa3.1753378331.git.namcao@linutronix.de
Reviewed-by: Gabriele Monaco <gmonaco@redhat.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Each struct rv_monitor has a unique struct rv_monitor_def associated with
it. struct rv_monitor is statically allocated, while struct rv_monitor_def
is dynamically allocated.
This makes the code more complicated than it should be:
- Lookup is required to get the associated rv_monitor_def from rv_monitor
- Dynamic memory allocation is required for rv_monitor_def. This is
harder to get right compared to static memory. For instance, there is
an existing mistake: rv_unregister_monitor() does not free the memory
allocated by rv_register_monitor(). This is fortunately not a real
memory leak problem, as rv_unregister_monitor() is never called.
Simplify and merge rv_monitor_def into rv_monitor.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/194449c00f87945c207aab4c96920c75796a4f53.1753378331.git.namcao@linutronix.de
Reviewed-by: Gabriele Monaco <gmonaco@redhat.com>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The events hugepage_set_pmd, hugepage_set_pud, hugepage_update_pmd and
hugepage_update_pud are only called when CONFIG_PPC_BOOK3S_64 is defined.
As each event can take up to 5K regardless if they are used or not, it's
best not to define them when they are not used. Add #ifdef around these
events when they are not used.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/20250612101259.0ad43e48@batman.local.home
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Document that using the MMIO helpers will automatically enable the
'fast_io' parameter. This makes the used locking scheme more transparent
and avoids superfluous setting of this parameter in drivers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://patch.msgid.link/20250725110337.4303-2-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"11 hotfixes. 9 are cc:stable and the remainder address post-6.15
issues or aren't considered necessary for -stable kernels.
7 are for MM"
* tag 'mm-hotfixes-stable-2025-07-24-18-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
sprintf.h requires stdarg.h
resource: fix false warning in __request_region()
mm/damon/core: commit damos_quota_goal->nid
kasan: use vmalloc_dump_obj() for vmalloc error reports
mm/ksm: fix -Wsometimes-uninitialized from clang-21 in advisor_mode_show()
mm: update MAINTAINERS entry for HMM
nilfs2: reject invalid file types when reading inodes
selftests/mm: fix split_huge_page_test for folio_split() tests
mailmap: add entry for Senozhatsky
mm/zsmalloc: do not pass __GFP_MOVABLE if CONFIG_COMPACTION=n
mm/vmscan: fix hwpoisoned large folio handling in shrink_folio_list
|
|
All callers have been converted to use filemap_grab_folio().
Link: https://lkml.kernel.org/r/20250721204619.163883-1-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Batch ptep_modify_prot_start/commit in preparation for optimizing
mprotect, implementing them as a simple loop over the corresponding single
pte helpers. Architecture may override these helpers.
Link: https://lkml.kernel.org/r/20250718090244.21092-4-dev.jain@arm.com
Signed-off-by: Dev Jain <dev.jain@arm.com>
Reviewed-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Barry Song <baohua@kernel.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: David Hildenbrand <david@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jann Horn <jannh@google.com>
Cc: Joey Gouly <joey.gouly@arm.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Lance Yang <ioworker0@gmail.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Cc: Yang Shi <yang@os.amperecomputing.com>
Cc: Yicong Yang <yangyicong@hisilicon.com>
Cc: Zhenhua Huang <quic_zhenhuah@quicinc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
With maple_tree supporting vma tree traversal under RCU and per-vma locks,
/proc/pid/maps can be read while holding individual vma locks instead of
locking the entire address space.
A completely lockless approach (walking vma tree under RCU) would be quite
complex with the main issue being get_vma_name() using callbacks which
might not work correctly with a stable vma copy, requiring original
(unstable) vma - see special_mapping_name() for example.
When per-vma lock acquisition fails, we take the mmap_lock for reading,
lock the vma, release the mmap_lock and continue. This fallback to mmap
read lock guarantees the reader to make forward progress even during lock
contention. This will interfere with the writer but for a very short time
while we are acquiring the per-vma lock and only when there was contention
on the vma reader is interested in.
We shouldn't see a repeated fallback to mmap read locks in practice, as
this require a very unlikely series of lock contentions (for instance due
to repeated vma split operations). However even if this did somehow
happen, we would still progress.
One case requiring special handling is when a vma changes between the time
it was found and the time it got locked. A problematic case would be if a
vma got shrunk so that its vm_start moved higher in the address space and
a new vma was installed at the beginning:
reader found: |--------VMA A--------|
VMA is modified: |-VMA B-|----VMA A----|
reader locks modified VMA A
reader reports VMA A: | gap |----VMA A----|
This would result in reporting a gap in the address space that does not
exist. To prevent this we retry the lookup after locking the vma, however
we do that only when we identify a gap and detect that the address space
was changed after we found the vma.
This change is designed to reduce mmap_lock contention and prevent a
process reading /proc/pid/maps files (often a low priority task, such as
monitoring/data collection services) from blocking address space updates.
Note that this change has a userspace visible disadvantage: it allows for
sub-page data tearing as opposed to the previous mechanism where data
tearing could happen only between pages of generated output data. Since
current userspace considers data tearing between pages to be acceptable,
we assume is will be able to handle sub-page data tearing as well.
Link: https://lkml.kernel.org/r/20250719182854.3166724-7-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: David Hildenbrand <david@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jeongjun Park <aha310510@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Kalesh Singh <kaleshsingh@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: "Paul E . McKenney" <paulmck@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Cc: T.J. Mercier <tjmercier@google.com>
Cc: Ye Bin <yebin10@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
This commit refactors __dump_page() into snapshot_page().
snapshot_page() tries to take a faithful snapshot of a page and its folio
representation. The snapshot is returned in the struct page_snapshot
parameter along with additional flags that are best retrieved at snapshot
creation time to reduce race windows.
This function is intended to be used by callers that need a stable
representation of a struct page and struct folio so that pointers or page
information doesn't change while working on a page.
The idea and original implementation of snapshot_page() comes from Matthew
Wilcox with suggestions for improvements from David Hildenbrand. All bugs
and misconceptions are mine.
[luizcap@redhat.com: fix set_ps_flags() commentary]
Link: https://lkml.kernel.org/r/d5c75701-b353-4536-a306-187fab0655b3@redhat.com
Link: https://lkml.kernel.org/r/637a03a05cb2e3df88f84ff9e9f9642374ef813a.1752499009.git.luizcap@redhat.com
Signed-off-by: Luiz Capitulino <luizcap@redhat.com>
Reviewed-by: Shivank Garg <shivankg@amd.com>
Tested-by: Harry Yoo <harry.yoo@oracle.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: SeongJae Park <sj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "mm: introduce snapshot_page()", v3.
This series introduces snapshot_page(), a helper function that can be used
to create a snapshot of a struct page and its associated struct folio.
This function is intended to help callers with a consistent view of a a
folio while reducing the chance of encountering partially updated or
inconsistent state, such as during folio splitting which could lead to
crashes and BUG_ON()s being triggered.
This patch (of 4):
Let's avoid working with the PMD when not required. If
vm_normal_page_pmd() would be called on something that is not a present
pmd, it would already be a bug (pfn possibly garbage).
While at it, let's support passing in any pfn covered by the huge zero
folio by masking off PFN bits -- which should be rather cheap.
Link: https://lkml.kernel.org/r/cover.1752499009.git.luizcap@redhat.com
Link: https://lkml.kernel.org/r/4940826e99f0c709a7cf7beb94f53288320aea5a.1752499009.git.luizcap@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Luiz Capitulino <luizcap@redhat.com>
Reviewed-by: Shivank Garg <shivankg@amd.com>
Tested-by: Harry Yoo <harry.yoo@oracle.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: SeongJae Park <sj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
memcg->socket_pressure is initialised with jiffies when the memcg is
created.
Once vmpressure detects that the cgroup is under memory pressure, the
field is updated with jiffies + HZ to signal the fact to the socket layer
and suppress memory allocation for one second.
Otherwise, the field is not updated.
mem_cgroup_under_socket_pressure() uses time_before() to check if jiffies
is less than memcg->socket_pressure, and this has a bug on 32-bit kernel.
if (time_before(jiffies, memcg->socket_pressure))
return true;
As time_before() casts the final result to long, the acceptable delta
between two timestamps is 2 ^ (BITS_PER_LONG - 1).
On 32-bit kernel with CONFIG_HZ=1000, this is about 24 days.
>>> (2 ** 31) / 1000 / 60 / 60 / 24
24.855134814814818
Once 24 days have passed since the last update of socket_pressure,
mem_cgroup_under_socket_pressure() starts to lie until the next 24 days
pass.
We don't need to worry about this on 64-bit machines unless they serve for
300 million years.
>>> (2 ** 63) / 1000 / 60 / 60 / 24 / 365
292471208.6775361
Let's convert memcg->socket_pressure to u64.
Performance teting:
I don't have a real 32-bit machine so this is a result on QEMU, but
with/without the u64 jiffie patch, the time spent in
mem_cgroup_under_socket_pressure() was 1~5us and I didn't see any
measurable delta.
no patch applied:
iperf3 273 [000] 137.296248:
probe:mem_cgroup_under_socket_pressure: (c13660d0)
c13660d1 mem_cgroup_under_socket_pressure+0x1
([kernel.kallsyms])
iperf3 273 [000] 137.296249:
probe:mem_cgroup_under_socket_pressure__return: (c13660d0 <- c1d8fd7f)
iperf3 273 [000] 137.296251:
probe:mem_cgroup_under_socket_pressure: (c13660d0)
c13660d1 mem_cgroup_under_socket_pressure+0x1
([kernel.kallsyms])
iperf3 273 [000] 137.296253:
probe:mem_cgroup_under_socket_pressure__return: (c13660d0 <- c1d8fd7f)
u64 jiffies patch applied:
iperf3 308 [001] 330.669370:
probe:mem_cgroup_under_socket_pressure: (c12ddba0)
c12ddba1 mem_cgroup_under_socket_pressure+0x1
([kernel.kallsyms])
iperf3 308 [001] 330.669371:
probe:mem_cgroup_under_socket_pressure__return: (c12ddba0 <- c1ce98bf)
iperf3 308 [001] 330.669382:
probe:mem_cgroup_under_socket_pressure: (c12ddba0)
c12ddba1 mem_cgroup_under_socket_pressure+0x1
([kernel.kallsyms])
iperf3 308 [001] 330.669384:
probe:mem_cgroup_under_socket_pressure__return: (c12ddba0 <- c1ce98bf)
So the u64 approach is good enough.
Link: https://lkml.kernel.org/r/20250717194645.1096500-1-kuniyu@google.com
Fixes: 8e8ae645249b ("mm: memcontrol: hook up vmpressure to socket pressure")
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Shakeel Butt <shakeel.butt@linux.dev>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <ncardwell@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
There are no longer any callers of hugetlb_free_pgd_range().
Link: https://lkml.kernel.org/r/20250716012611.10369-4-anthony.yznaga@oracle.com
Signed-off-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Oscar Salvador <osalvador@suse.de>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Alexandre Ghiti <alexghiti@rivosinc.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: David Hildenbrand <david@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Right now it appears that the code is relying upon the returned
destination address having bits outside PAGE_MASK to indicate whether an
error value is specified, and decrementing the increased refcount on the
uffd ctx if so.
This is not a safe means of determining an error value, so instead, be
specific. It makes far more sense to do so in a dedicated error path, so
add mremap_userfaultfd_fail() for this purpose and use this when an error
arises.
A vm_userfaultfd_ctx is not established until we are at the point where
mremap_userfaultfd_prep() is invoked in copy_vma_and_data(), so this is a
no-op until this happens.
That is - uffd remap notification only occurs if the VMA is actually moved
- at which point a UFFD_EVENT_REMAP event is raised.
No errors can occur after this point currently, though it's certainly not
guaranteed this will always remain the case, and we mustn't rely on this.
However, the reason for needing to handle this case is that, when an error
arises on a VMA move at the point of adjusting page tables, we revert this
operation, and propagate the error.
At this point, it is not correct to raise a uffd remap event, and we must
handle it.
This refactoring makes it abundantly clear what we are doing.
We assume vrm->new_addr is always valid, which a prior change made the
case even for mremap() invocations which don't move the VMA, however given
no uffd context would be set up in this case it's immaterial to this
change anyway.
No functional change intended.
Link: https://lkml.kernel.org/r/a70e8a1f7bce9f43d1431065b414e0f212297297.1752770784.git.lorenzo.stoakes@oracle.com
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jann Horn <jannh@google.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Dropping a lock, just to demand it again for an afterthought, cannot be
good if contended: convert lru_note_cost() to lru_note_cost_unlock_irq().
[hughd@google.com: delete unneeded comment]
Link: https://lkml.kernel.org/r/dbf9352a-1ed9-a021-c0c7-9309ac73e174@google.com
Link: https://lkml.kernel.org/r/21100102-51b6-79d5-03db-1bb7f97fa94c@google.com
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Roman Gushchin <roman.gushchin@linux.dev>
Tested-by: Roman Gushchin <roman.gushchin@linux.dev>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Cc: David Hildenbrand <david@redhat.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Instead of using '0' and '1' for napi threaded state use an enum with
'disabled' and 'enabled' states.
Tested:
./tools/testing/selftests/net/nl_netdev.py
TAP version 13
1..7
ok 1 nl_netdev.empty_check
ok 2 nl_netdev.lo_check
ok 3 nl_netdev.page_pool_check
ok 4 nl_netdev.napi_list_check
ok 5 nl_netdev.dev_set_threaded
ok 6 nl_netdev.napi_set_threaded
ok 7 nl_netdev.nsim_rxq_reset_down
# Totals: pass:7 fail:0 xfail:0 xpass:0 skip:0 error:0
Signed-off-by: Samiullah Khawaja <skhawaja@google.com>
Link: https://patch.msgid.link/20250723013031.2911384-4-skhawaja@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prepare for adding an enum type for NAPI threaded states by adding
netif_threaded_enable API. De-export the existing netif_set_threaded API
and only use it internally. Update existing drivers to use
netif_threaded_enable instead of the de-exported netif_set_threaded.
Note that dev_set_threaded used by mt76 debugfs file is unchanged.
Signed-off-by: Samiullah Khawaja <skhawaja@google.com>
Link: https://patch.msgid.link/20250723013031.2911384-3-skhawaja@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move multiple copies of same code snippet doing `gro_flush` and
`gro_normal_list` into separate helper function.
Signed-off-by: Samiullah Khawaja <skhawaja@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250723013031.2911384-2-skhawaja@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
core:
- hci_sync: fix double free in 'hci_discovery_filter_clear()'
- hci_event: Mask data status from LE ext adv reports
- hci_devcd_dump: fix out-of-bounds via dev_coredumpv
- ISO: add socket option to report packet seqnum via CMSG
- hci_event: Add support for handling LE BIG Sync Lost event
- ISO: Support SCM_TIMESTAMPING for ISO TS
- hci_core: Add PA_LINK to distinguish BIG sync and PA sync connections
- hci_sock: Reset cookie to zero in hci_sock_free_cookie()
drivers:
- btusb: Add new VID/PID 0489/e14e for MT7925
- btusb: Add a new VID/PID 2c7c/7009 for MT7925
- btusb: Add RTL8852BE device 0x13d3:0x3618
- btusb: Add support for variant of RTL8851BE (USB ID 13d3:3601)
- btusb: Add USB ID 3625:010b for TP-LINK Archer TX10UB Nano
- btusb: QCA: Support downloading custom-made firmwares
- btusb: Add one more ID 0x28de:0x1401 for Qualcomm WCN6855
- nxp: add support for supply and reset
- btnxpuart: Add support for 4M baudrate
- btnxpuart: Correct the Independent Reset handling after FW dump
- btnxpuart: Add uevents for FW dump and FW download complete
- btintel: Define a macro for Intel Reset vendor command
- btintel_pcie: Support Function level reset
- btintel_pcie: Add support for device 0x4d76
- btintel_pcie: Make driver wait for alive interrupt
- btintel_pcie: Fix Alive Context State Handling
- hci_qca: Enable ISO data packet RX
* tag 'for-net-next-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (42 commits)
Bluetooth: Add PA_LINK to distinguish BIG sync and PA sync connections
Bluetooth: hci_event: Mask data status from LE ext adv reports
Bluetooth: btintel_pcie: Fix Alive Context State Handling
Bluetooth: btintel_pcie: Make driver wait for alive interrupt
Bluetooth: hci_devcd_dump: fix out-of-bounds via dev_coredumpv
Bluetooth: hci_sync: fix double free in 'hci_discovery_filter_clear()'
Bluetooth: btusb: Add one more ID 0x28de:0x1401 for Qualcomm WCN6855
Bluetooth: btusb: Sort WCN6855 device IDs by VID and PID
Bluetooth: btusb: QCA: Support downloading custom-made firmwares
Bluetooth: btnxpuart: Add uevents for FW dump and FW download complete
Bluetooth: btnxpuart: Correct the Independent Reset handling after FW dump
Bluetooth: ISO: Support SCM_TIMESTAMPING for ISO TS
Bluetooth: ISO: add socket option to report packet seqnum via CMSG
Bluetooth: btintel: Define a macro for Intel Reset vendor command
Bluetooth: Fix typos in comments
Bluetooth: RFCOMM: Fix typos in comments
Bluetooth: aosp: Fix typo in comment
Bluetooth: hci_bcm4377: Fix typo in comment
Bluetooth: btrtl: Fix typo in comment
Bluetooth: btmtk: Fix typo in log string
...
====================
Link: https://patch.msgid.link/20250723190233.166823-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In file included from drivers/crypto/intel/qat/qat_common/adf_pm_dbgfs_utils.c:4:
include/linux/sprintf.h:11:54: error: unknown type name 'va_list'
11 | __printf(2, 0) int vsprintf(char *buf, const char *, va_list);
| ^~~~~~~
include/linux/sprintf.h:1:1: note: 'va_list' is defined in header '<stdarg.h>'; this is probably fixable by adding '#include <stdarg.h>'
Link: https://lkml.kernel.org/r/20250721173754.42865913@canb.auug.org.au
Fixes: 39ced19b9e60 ("lib/vsprintf: split out sprintf() and friends")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andriy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Another wireless update:
- rtw89:
- STA+P2P concurrency
- support for USB devices RTL8851BU/RTL8852BU
- ath9k: OF support
- ath12k:
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- iwlwifi: some FIPS interoperability
- brcm80211: support SDIO 43751 device
- rt2x00: better DT/OF support
- cfg80211/mac80211:
- improved S1G support
- beacon monitor for MLO
* tag 'wireless-next-2025-07-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (199 commits)
ssb: use new GPIO line value setter callbacks for the second GPIO chip
wifi: Fix typos
wifi: brcmsmac: Use str_true_false() helper
wifi: brcmfmac: fix EXTSAE WPA3 connection failure due to AUTH TX failure
wifi: brcm80211: Remove yet more unused functions
wifi: brcm80211: Remove more unused functions
wifi: brcm80211: Remove unused functions
wifi: iwlwifi: Revert "wifi: iwlwifi: remove support of several iwl_ppag_table_cmd versions"
wifi: iwlwifi: check validity of the FW API range
wifi: iwlwifi: don't export symbols that we shouldn't
wifi: iwlwifi: mld: use spec link id and not FW link id
wifi: iwlwifi: mld: decode EOF bit for AMPDUs
wifi: iwlwifi: Remove support for rx OMI bandwidth reduction
wifi: iwlwifi: stop supporting iwl_omi_send_status_notif ver 1
wifi: iwlwifi: remove SC2F firmware support
wifi: iwlwifi: mvm: Remove NAN support
wifi: iwlwifi: mld: avoid outdated reorder buffer head_sn
wifi: iwlwifi: mvm: avoid outdated reorder buffer head_sn
wifi: iwlwifi: disable certain features for fips_enabled
wifi: iwlwifi: mld: support channel survey collection for ACS scans
...
====================
Link: https://patch.msgid.link/20250724100349.21564-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
GCC appears to have kind of fragile inlining heuristics, in the
sense that it can change whether or not it inlines something based on
optimizations. It looks like the kcov instrumentation being added (or in
this case, removed) from a function changes the optimization results,
and some functions marked "inline" are _not_ inlined. In that case,
we end up with __init code calling a function not marked __init, and we
get the build warnings I'm trying to eliminate in the coming patch that
adds __no_sanitize_coverage to __init functions:
WARNING: modpost: vmlinux: section mismatch in reference: xbc_exit+0x8 (section: .text.unlikely) -> _xbc_exit (section: .init.text)
WARNING: modpost: vmlinux: section mismatch in reference: real_mode_size_needed+0x15 (section: .text.unlikely) -> real_mode_blob_end (section: .init.data)
WARNING: modpost: vmlinux: section mismatch in reference: __set_percpu_decrypted+0x16 (section: .text.unlikely) -> early_set_memory_decrypted (section: .init.text)
WARNING: modpost: vmlinux: section mismatch in reference: memblock_alloc_from+0x26 (section: .text.unlikely) -> memblock_alloc_try_nid (section: .init.text)
WARNING: modpost: vmlinux: section mismatch in reference: acpi_arch_set_root_pointer+0xc (section: .text.unlikely) -> x86_init (section: .init.data)
WARNING: modpost: vmlinux: section mismatch in reference: acpi_arch_get_root_pointer+0x8 (section: .text.unlikely) -> x86_init (section: .init.data)
WARNING: modpost: vmlinux: section mismatch in reference: efi_config_table_is_usable+0x16 (section: .text.unlikely) -> xen_efi_config_table_is_usable (section: .init.text)
This problem is somewhat fragile (though using either __always_inline
or __init will deterministically solve it), but we've tripped over
this before with GCC and the solution has usually been to just use
__always_inline and move on.
For x86 this means forcing several functions to be inline with
__always_inline.
Link: https://lore.kernel.org/r/20250724055029.3623499-2-kees@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
Add doorbell support with the help of three new registers:
PCIE_ENDPOINT_TEST_DB_BAR, PCIE_ENDPOINT_TEST_DB_ADDR, and
PCIE_ENDPOINT_TEST_DB_DATA.
The testcase works by triggering the doorbell in Endpoint by writing the
value from PCI_ENDPOINT_TEST_DB_DATA register to the address provided by
PCI_ENDPOINT_TEST_DB_OFFSET register of the BAR indicated by the
PCIE_ENDPOINT_TEST_DB_BAR register and waiting for the completion status
from the Endpoint.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[mani: removed one spurious change and reworded the commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250710-ep-msi-v21-7-57683fc7fb25@nxp.com
|
|
alignment
Add pci_epf_align_inbound_addr() to align the inbound addresses according
to PCI BAR alignment requirements. The aligned base address and offset are
returned via 'base' and 'off' parameters.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[mani: reworded kernel-doc and commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250710-ep-msi-v21-5-57683fc7fb25@nxp.com
|
|
Implement the doorbell feature by mapping the EP's MSI interrupt controller
message address to a dedicated BAR.
The EPF driver should pass the actual message data to be written to the
message address by the host through implementation-specific logic.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[mani: minor code cleanups and reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: fix kernel-doc]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250710-ep-msi-v21-3-57683fc7fb25@nxp.com
|
|
ubi_flush() was added in 2012 as part of
commit 62f384552b67 ("UBI: modify ubi_wl_flush function to clear work queue
for a lnum")
but has remained unused.
(It's friend ubi_wl_flush() is still used)
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc8).
Conflicts:
drivers/net/ethernet/microsoft/mana/gdma_main.c
9669ddda18fb ("net: mana: Fix warnings for missing export.h header inclusion")
755391121038 ("net: mana: Allocate MSI-X vectors dynamically")
https://lore.kernel.org/20250711130752.23023d98@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/ti/icssg/icssg_prueth.h
6e86fb73de0f ("net: ti: icssg-prueth: Fix buffer allocation for ICSSG")
ffe8a4909176 ("net: ti: icssg-prueth: Read firmware-names from device tree")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new module for common handling of Admin Queue related logic.
Start by a helper for error to string conversion. This lives inside
libie/, but is a separate module what follows our logic of splitting
into topical modules, to avoid pulling in not needed stuff, and have
better organization in general.
Olek suggested how to better solve the error to string conversion.
It will be used in follow-up patches in ice, i40e and iavf.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use libie_aq_desc instead of i40e_aq_desc. Do needed changes to allow
clean build.
Get version descriptor is a little less detailed on i40e. To not mess up
with shifting or union inside libie desc use get version descriptor from
i40e.
Move additional caps for i40e to libie.
Fix RCT in declaration that is using libie_aq_desc;
Use libie_aq_raw() wherever it can be used.
The libie aq error is extended, cover it in ice driver just to clean
build. In next patches the libie code for that will be used in each
of intel driver.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use libie_aq_desc instead of ixgbe_aci_desc. Do needed changes to allow
clean build.
Move additional caps used in ixgbe to libie.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The descriptor structure is the same in ice, ixgbe and i40e. Move it to
common libie header to use it across different driver.
Leave device specific adminq commands in separate folders. This lead to
a change that need to be done in filling/getting descriptor:
- previous: struct specific_desc *cmd;
cmd = &desc.params.specific_desc;
- now: struct specific_desc *cmd;
cmd = libie_aq_raw(&desc);
Do this changes across the driver to allow clean build. The casting only
have to be done in case of specific descriptors, for generic one union
can still be used.
Changes beside code moving:
- change ICE_ prefix to LIBIE_ prefix (ice_ and libie_ too)
- remove shift variables not otherwise needed (in libie_aq_flags)
- fill/get descriptor data based on desc.params.raw whenever the
descriptor isn't defined in libie
- move defines from the libie_aq_sth structure outside
- add libie_aq_raw helper and use it instead of explicit casting
Reviewed by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Two important arm64 fixes ahead of the 6.16 release.
The first fixes a regression introduced during the merge window where
the KVM UUID (which is used to advertise KVM-specific hypercalls for
things like time synchronisation in the guest) was corrupted thanks to
an endianness bug introduced when converting the code to use the
UUID_INIT() helper.
The second fixes a stack-pointer corruption issue during
context-switch which has been observed in the wild when taking a
pseudo-NMI with shadow call stack enabled.
Summary:
- Fix broken UUID value for the KVM/arm64 hypervisor SMCCC interface
- Fix stack corruption on context-switch, primarily seen on (but not
limited to) configurations with both pNMI and SCS enabled"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/entry: Mask DAIF in cpu_switch_to(), call_on_irq_stack()
arm64: kvm, smccc: Fix vendor uuid
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can and xfrm.
The TI regression notified last week is actually on our net-next tree,
it does not affect 6.16.
We are investigating a virtio regression which is quite hard to
reproduce - currently only our CI sporadically hits it. Hopefully it
should not be critical, and I'm not sure that an additional week would
be enough to solve it.
Current release - fix to a fix:
- sched: sch_qfq: avoid sleeping in atomic context in qfq_delete_class
Previous releases - regressions:
- xfrm:
- set transport header to fix UDP GRO handling
- delete x->tunnel as we delete x
- eth:
- mlx5: fix memory leak in cmd_exec()
- i40e: when removing VF MAC filters, avoid losing PF-set MAC
- gve: fix stuck TX queue for DQ queue format
Previous releases - always broken:
- can: fix NULL pointer deref of struct can_priv::do_set_mode
- eth:
- ice: fix a null pointer dereference in ice_copy_and_init_pkg()
- ism: fix concurrency management in ism_cmd()
- dpaa2: fix device reference count leak in MAC endpoint handling
- icssg-prueth: fix buffer allocation for ICSSG
Misc:
- selftests: mptcp: increase code coverage"
* tag 'net-6.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (34 commits)
net: hns3: default enable tx bounce buffer when smmu enabled
net: hns3: fixed vf get max channels bug
net: hns3: disable interrupt when ptp init failed
net: hns3: fix concurrent setting vlan filter issue
s390/ism: fix concurrency management in ism_cmd()
selftests: drv-net: wait for iperf client to stop sending
MAINTAINERS: Add in6.h to MAINTAINERS
selftests: netfilter: tone-down conntrack clash test
can: netlink: can_changelink(): fix NULL pointer deref of struct can_priv::do_set_mode
net/sched: sch_qfq: Avoid triggering might_sleep in atomic context in qfq_delete_class
gve: Fix stuck TX queue for DQ queue format
net: appletalk: Fix use-after-free in AARP proxy probe
net: bcmasp: Restore programming of TX map vector register
selftests: mptcp: connect: also cover checksum
selftests: mptcp: connect: also cover alt modes
e1000e: ignore uninitialized checksum word on tgp
e1000e: disregard NVM checksum on tgp when valid checksum bit is not set
ice: Fix a null pointer dereference in ice_copy_and_init_pkg()
i40e: When removing VF MAC filters, only check PF-set MAC
i40e: report VF tx_dropped with tx_errors instead of tx_discards
...
|
|
* for-next/feat_mte_store_only:
: MTE feature to restrict tag checking to store only operations
kselftest/arm64/mte: Add MTE_STORE_ONLY testcases
kselftest/arm64/mte: Preparation for mte store only test
kselftest/arm64/abi: Add MTE_STORE_ONLY feature hwcap test
KVM: arm64: Expose MTE_STORE_ONLY feature to guest
arm64/hwcaps: Add MTE_STORE_ONLY hwcaps
arm64/kernel: Support store-only mte tag check
prctl: Introduce PR_MTE_STORE_ONLY
arm64/cpufeature: Add MTE_STORE_ONLY feature
|
|
'for-next/misc', 'for-next/acpi', 'for-next/debug-entry', 'for-next/feat_mte_tagged_far', 'for-next/kselftest', 'for-next/mdscr-cleanup' and 'for-next/vmap-stack', remote-tracking branch 'arm64/for-next/perf' into for-next/core
* arm64/for-next/perf: (23 commits)
drivers/perf: hisi: Support PMUs with no interrupt
drivers/perf: hisi: Relax the event number check of v2 PMUs
drivers/perf: hisi: Add support for HiSilicon SLLC v3 PMU driver
drivers/perf: hisi: Use ACPI driver_data to retrieve SLLC PMU information
drivers/perf: hisi: Add support for HiSilicon DDRC v3 PMU driver
drivers/perf: hisi: Simplify the probe process for each DDRC version
perf/arm-ni: Support sharing IRQs within an NI instance
perf/arm-ni: Consolidate CPU affinity handling
perf/cxlpmu: Fix typos in cxl_pmu.c comments and documentation
perf/cxlpmu: Remove unintended newline from IRQ name format string
perf/cxlpmu: Fix devm_kcalloc() argument order in cxl_pmu_probe()
perf: arm_spe: Relax period restriction
perf: arm_pmuv3: Add support for the Branch Record Buffer Extension (BRBE)
KVM: arm64: nvhe: Disable branch generation in nVHE guests
arm64: Handle BRBE booting requirements
arm64/sysreg: Add BRBE registers and fields
perf/arm: Add missing .suppress_bind_attrs
perf/arm-cmn: Reduce stack usage during discovery
perf: imx9_perf: make the read-only array mask static const
perf/arm-cmn: Broaden module description for wider interconnect support
...
* for-next/livepatch:
: Support for HAVE_LIVEPATCH on arm64
arm64: Kconfig: Keep selects somewhat alphabetically ordered
arm64: Implement HAVE_LIVEPATCH
arm64: stacktrace: Implement arch_stack_walk_reliable()
arm64: stacktrace: Check kretprobe_find_ret_addr() return value
arm64/module: Use text-poke API for late relocations.
* for-next/user-contig-bbml2:
: Optimise the TLBI when folding/unfolding contigous PTEs on hardware with BBML2 and no TLB conflict aborts
arm64/mm: Elide tlbi in contpte_convert() under BBML2
iommu/arm: Add BBM Level 2 smmu feature
arm64: Add BBM Level 2 cpu feature
arm64: cpufeature: Introduce MATCH_ALL_EARLY_CPUS capability type
* for-next/misc:
: Miscellaneous arm64 patches
arm64/gcs: task_gcs_el0_enable() should use passed task
arm64: signal: Remove ISB when resetting POR_EL0
arm64/mm: Drop redundant addr increment in set_huge_pte_at()
arm64: Mark kernel as tainted on SAE and SError panic
arm64/gcs: Don't call gcs_free() when releasing task_struct
arm64: fix unnecessary rebuilding when CONFIG_DEBUG_EFI=y
arm64/mm: Optimize loop to reduce redundant operations of contpte_ptep_get
arm64: pi: use 'targets' instead of extra-y in Makefile
* for-next/acpi:
: Various ACPI arm64 changes
ACPI: Suppress misleading SPCR console message when SPCR table is absent
ACPI: Return -ENODEV from acpi_parse_spcr() when SPCR support is disabled
* for-next/debug-entry:
: Simplify the debug exception entry path
arm64: debug: remove debug exception registration infrastructure
arm64: debug: split bkpt32 exception entry
arm64: debug: split brk64 exception entry
arm64: debug: split hardware watchpoint exception entry
arm64: debug: split single stepping exception entry
arm64: debug: refactor reinstall_suspended_bps()
arm64: debug: split hardware breakpoint exception entry
arm64: entry: Add entry and exit functions for debug exceptions
arm64: debug: remove break/step handler registration infrastructure
arm64: debug: call step handlers statically
arm64: debug: call software breakpoint handlers statically
arm64: refactor aarch32_break_handler()
arm64: debug: clean up single_step_handler logic
* for-next/feat_mte_tagged_far:
: Support for reporting the non-address bits during a synchronous MTE tag check fault
kselftest/arm64/mte: Add mtefar tests on check_mmap_options
kselftest/arm64/mte: Refactor check_mmap_option test
kselftest/arm64/mte: Add verification for address tag in signal handler
kselftest/arm64/mte: Add address tag related macro and function
kselftest/arm64/mte: Check MTE_FAR feature is supported
kselftest/arm64/mte: Register mte signal handler with SA_EXPOSE_TAGBITS
kselftest/arm64: Add MTE_FAR hwcap test
KVM: arm64: Expose FEAT_MTE_TAGGED_FAR feature to guest
arm64: Report address tag when FEAT_MTE_TAGGED_FAR is supported
arm64/cpufeature: Add FEAT_MTE_TAGGED_FAR feature
* for-next/kselftest:
: Kselftest updates for arm64
kselftest/arm64: Handle attempts to disable SM on SME only systems
kselftest/arm64: Fix SVE write data generation for SME only systems
kselftest/arm64: Test SME on SME only systems in fp-ptrace
kselftest/arm64: Test FPSIMD format data writes via NT_ARM_SVE in fp-ptrace
kselftest/arm64: Allow sve-ptrace to run on SME only systems
kselftest/arm4: Provide local defines for AT_HWCAP3
kselftest/arm64: Specify SVE data when testing VL set in sve-ptrace
kselftest/arm64: Fix test for streaming FPSIMD write in sve-ptrace
kselftest/arm64: Fix check for setting new VLs in sve-ptrace
kselftest/arm64: Convert tpidr2 test to use kselftest.h
* for-next/mdscr-cleanup:
: Drop redundant DBG_MDSCR_* macros
KVM: selftests: Change MDSCR_EL1 register holding variables as uint64_t
arm64/debug: Drop redundant DBG_MDSCR_* macros
* for-next/vmap-stack:
: Force VMAP_STACK on arm64
arm64: remove CONFIG_VMAP_STACK checks from entry code
arm64: remove CONFIG_VMAP_STACK checks from SDEI stack handling
arm64: remove CONFIG_VMAP_STACK checks from stacktrace overflow logic
arm64: remove CONFIG_VMAP_STACK conditionals from traps overflow stack
arm64: remove CONFIG_VMAP_STACK conditionals from irq stack setup
arm64: Remove CONFIG_VMAP_STACK conditionals from THREAD_SHIFT and THREAD_ALIGN
arm64: efi: Remove CONFIG_VMAP_STACK check
arm64: Mandate VMAP_STACK
arm64: efi: Fix KASAN false positive for EFI runtime stack
arm64/ptrace: Fix stack-out-of-bounds read in regs_get_kernel_stack_nth()
arm64/gcs: Don't call gcs_free() during flush_gcs()
arm64: Restrict pagetable teardown to avoid false warning
docs: arm64: Fix ICC_SRE_EL2 register typo in booting.rst
|
|
The traditional interfaces are only used on a small number of ancient
boards. Make these optional now so they can be disabled by default.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20250722153634.3683927-1-arnd@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.17
There's a few new drivers here and quite a lot of cleanup work from
Morimoto-san but generally this has been quite a quiet release,
resulting in a fairly small diffstat. Highlights include:
- Refactoring of the Kconfig menus to be hopefully more consistant and
easier to navigate.
- Refactoring of the DAPM code, mainly hiding functionality that
doesn't need to be exposed to drivers.
- Removal of the unused upstream weak paths DAPM functionality.
- Further work on the generic handling for SoundWire SDCA devices.
- Cleanups of our usage of the PM autosuspend functions, this pulls in
some PM core changes on a shared tag.
- Support for AMD ACP7.2 and SoundWire on ACP 7.1, Fairphone 4 & 5,
various Intel systems, Qualcomm QCS8275, Richtek RTQ9124 and TI TAS5753.
|
|
Many of the DisCo properties that specify Control values have an
additional variant that specifies a separate value for each Control
Number. Add support for these.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250718135432.1048566-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into gpio/for-next
Immutable branch between MFD, GPIO, Power and SoC due for the v6.17 merge window
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2025-07-23
1) Premption fixes for xfrm_state_find.
From Sabrina Dubroca.
2) Initialize offload path also for SW IPsec GRO. This fixes a
performance regression on SW IPsec offload.
From Leon Romanovsky.
3) Fix IPsec UDP GRO for IKE packets.
From Tobias Brunner,
4) Fix transport header setting for IPcomp after decompressing.
From Fernando Fernandez Mancera.
5) Fix use-after-free when xfrmi_changelink tries to change
collect_md for a xfrm interface.
From Eyal Birger .
6) Delete the special IPcomp x->tunnel state along with the state x
to avoid refcount problems.
From Sabrina Dubroca.
Please pull or let me know if there are problems.
* tag 'ipsec-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
Revert "xfrm: destroy xfrm_state synchronously on net exit path"
xfrm: delete x->tunnel as we delete x
xfrm: interface: fix use-after-free after changing collect_md xfrm interface
xfrm: ipcomp: adjust transport header after decompressing
xfrm: Set transport header to fix UDP GRO handling
xfrm: always initialize offload path
xfrm: state: use a consistent pcpu_id in xfrm_state_find
xfrm: state: initialize state_ptrs earlier in xfrm_state_find
====================
Link: https://patch.msgid.link/20250723075417.3432644-1-steffen.klassert@secunet.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
