| Age | Commit message (Collapse) | Author |
|---|
|
The current behavior of IP defragmentation is inconsistent:
- some overlapping/wrong length fragments are dropped without
affecting the queue;
- most overlapping fragments cause the whole frag queue to be dropped.
This patch brings consistency: if a bad fragment is detected,
the whole frag queue is dropped. Two major benefits:
- fail fast: corrupted frag queues are cleared immediately, instead of
by timeout;
- testing of overlapping fragments is now much easier: any kind of
random fragment length mutation now leads to the frag queue being
discarded (IP packet dropped); before this patch, some overlaps were
"corrected", with tests not seeing expected packet drops.
Note that in one case (see "if (end&7)" conditional) the current
behavior is preserved as there are concerns that this could be
legitimate padding.
Signed-off-by: Peter Oskolkov <posk@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since [gs]et_settings ethtool_ops callbacks have been deprecated in
February 2016, all in tree NIC drivers have been converted to provide
[gs]et_link_ksettings() and out of tree drivers have had enough time to do
the same.
Drop get_settings() and set_settings() and implement both ETHTOOL_[GS]SET
and ETHTOOL_[GS]LINKSETTINGS only using [gs]et_link_ksettings().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtnl_unregister_all(PF_INET6) gets called from inet6_init in cases when
no handler has been registered for PF_INET6 yet, for example if
ip6_mr_init() fails. Abort and avoid a NULL pointer deref in that case.
Example of panic (triggered by faking a failure of
register_pernet_subsys):
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
[...]
RIP: 0010:rtnl_unregister_all+0x17e/0x2a0
[...]
Call Trace:
? rtnetlink_net_init+0x250/0x250
? sock_unregister+0x103/0x160
? kernel_getsockopt+0x200/0x200
inet6_init+0x197/0x20d
Fixes: e2fddf5e96df ("[IPV6]: Make af_inet6 to check ip6_route_init return value.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6d0bfe226116 ("net: ipv6: Add IPv6 support to the ping socket.")
contains an error in the cleanup path of inet6_init(): when
proto_register(&pingv6_prot, 1) fails, we try to unregister
&pingv6_prot. When rawv6_init() fails, we skip unregistering
&pingv6_prot.
Example of panic (triggered by faking a failure of
proto_register(&pingv6_prot, 1)):
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
[...]
RIP: 0010:__list_del_entry_valid+0x79/0x160
[...]
Call Trace:
proto_unregister+0xbb/0x550
? trace_preempt_on+0x6f0/0x6f0
? sock_no_shutdown+0x10/0x10
inet6_init+0x153/0x1b8
Fixes: 6d0bfe226116 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 15e668070a64 ("ipv6: reorder icmpv6_init() and ip6_mr_init()")
moved the cleanup label for ipmr_fail, but should have changed the
contents of the cleanup labels as well. Now we can end up cleaning up
icmpv6 even though it hasn't been initialized (jump to icmp_fail or
ipmr_fail).
Simply undo things in the reverse order of their initialization.
Example of panic (triggered by faking a failure of icmpv6_init):
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
[...]
RIP: 0010:__list_del_entry_valid+0x79/0x160
[...]
Call Trace:
? lock_release+0x8a0/0x8a0
unregister_pernet_operations+0xd4/0x560
? ops_free_list+0x480/0x480
? down_write+0x91/0x130
? unregister_pernet_subsys+0x15/0x30
? down_read+0x1b0/0x1b0
? up_read+0x110/0x110
? kmem_cache_create_usercopy+0x1b4/0x240
unregister_pernet_subsys+0x1d/0x30
icmpv6_cleanup+0x1d/0x30
inet6_init+0x1b5/0x23f
Fixes: 15e668070a64 ("ipv6: reorder icmpv6_init() and ip6_mr_init()")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in the (rare) case of failure in nla_nest_start(), missing NULL checks in
tcf_pedit_key_ex_dump() can make the following command
# tc action add action pedit ex munge ip ttl set 64
dereference a NULL pointer:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 800000007d1cd067 P4D 800000007d1cd067 PUD 7acd3067 PMD 0
Oops: 0002 [#1] SMP PTI
CPU: 0 PID: 3336 Comm: tc Tainted: G E 4.18.0.pedit+ #425
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:tcf_pedit_dump+0x19d/0x358 [act_pedit]
Code: be 02 00 00 00 48 89 df 66 89 44 24 20 e8 9b b1 fd e0 85 c0 75 46 8b 83 c8 00 00 00 49 83 c5 08 48 03 83 d0 00 00 00 4d 39 f5 <66> 89 04 25 00 00 00 00 0f 84 81 01 00 00 41 8b 45 00 48 8d 4c 24
RSP: 0018:ffffb5d4004478a8 EFLAGS: 00010246
RAX: ffff8880fcda2070 RBX: ffff8880fadd2900 RCX: 0000000000000000
RDX: 0000000000000002 RSI: ffffb5d4004478ca RDI: ffff8880fcda206e
RBP: ffff8880fb9cb900 R08: 0000000000000008 R09: ffff8880fcda206e
R10: ffff8880fadd2900 R11: 0000000000000000 R12: ffff8880fd26cf40
R13: ffff8880fc957430 R14: ffff8880fc957430 R15: ffff8880fb9cb988
FS: 00007f75a537a740(0000) GS:ffff8880fda00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 000000007a2fa005 CR4: 00000000001606f0
Call Trace:
? __nla_reserve+0x38/0x50
tcf_action_dump_1+0xd2/0x130
tcf_action_dump+0x6a/0xf0
tca_get_fill.constprop.31+0xa3/0x120
tcf_action_add+0xd1/0x170
tc_ctl_action+0x137/0x150
rtnetlink_rcv_msg+0x263/0x2d0
? _cond_resched+0x15/0x40
? rtnl_calcit.isra.30+0x110/0x110
netlink_rcv_skb+0x4d/0x130
netlink_unicast+0x1a3/0x250
netlink_sendmsg+0x2ae/0x3a0
sock_sendmsg+0x36/0x40
___sys_sendmsg+0x26f/0x2d0
? do_wp_page+0x8e/0x5f0
? handle_pte_fault+0x6c3/0xf50
? __handle_mm_fault+0x38e/0x520
? __sys_sendmsg+0x5e/0xa0
__sys_sendmsg+0x5e/0xa0
do_syscall_64+0x5b/0x180
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f75a4583ba0
Code: c3 48 8b 05 f2 62 2c 00 f7 db 64 89 18 48 83 cb ff eb dd 0f 1f 80 00 00 00 00 83 3d fd c3 2c 00 00 75 10 b8 2e 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 ae cc 00 00 48 89 04 24
RSP: 002b:00007fff60ee7418 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007fff60ee7540 RCX: 00007f75a4583ba0
RDX: 0000000000000000 RSI: 00007fff60ee7490 RDI: 0000000000000003
RBP: 000000005b842d3e R08: 0000000000000002 R09: 0000000000000000
R10: 00007fff60ee6ea0 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fff60ee7554 R14: 0000000000000001 R15: 000000000066c100
Modules linked in: act_pedit(E) ip6table_filter ip6_tables iptable_filter binfmt_misc crct10dif_pclmul ext4 crc32_pclmul mbcache ghash_clmulni_intel jbd2 pcbc snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd snd_timer cryptd glue_helper snd joydev pcspkr soundcore virtio_balloon i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi virtio_net net_failover virtio_blk virtio_console failover qxl crc32c_intel drm_kms_helper syscopyarea serio_raw sysfillrect sysimgblt fb_sys_fops ttm drm ata_piix virtio_pci libata virtio_ring i2c_core virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_pedit]
CR2: 0000000000000000
Like it's done for other TC actions, give up dumping pedit rules and return
an error if nla_nest_start() returns NULL.
Fixes: 71d0ed7079df ("net/act_pedit: Support using offset relative to the conventional network headers")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a use-after-free in tipc_group_fill_sock_diag(),
where tipc_group_fill_sock_diag() still reads tsk->group meanwhile
tipc_group_delete() just deletes it in tipc_release().
tipc_nl_sk_walk() aims to lock this sock when walking each sock
in the hash table to close race conditions with sock changes like
this one, by acquiring tsk->sk.sk_lock.slock spinlock, unfortunately
this doesn't work at all. All non-BH call path should take
lock_sock() instead to make it work.
tipc_nl_sk_walk() brutally iterates with raw rht_for_each_entry_rcu()
where RCU read lock is required, this is the reason why lock_sock()
can't be taken on this path. This could be resolved by switching to
rhashtable iterator API's, where taking a sleepable lock is possible.
Also, the iterator API's are friendly for restartable calls like
diag dump, the last position is remembered behind the scence,
all we need to do here is saving the iterator into cb->args[].
I tested this with parallel tipc diag dump and thousands of tipc
socket creation and release, no crash or memory leak.
Reported-by: syzbot+b9c8f3ab2994b7cd1625@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rhashtable_walk_exit() must be paired with rhashtable_walk_enter().
Fixes: 40f9f4397060 ("tipc: Fix tipc_sk_reinit race conditions")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the commit d6990976af7c ("vti6: fix PMTU caching and reporting
on xmit") '!skb->ignore_df' check was always true because the function
skb_scrub_packet() was called before it, resetting ignore_df to zero.
In the commit, skb_scrub_packet() was moved below, and now this check
can be false for the packet, e.g. when sending it in the two fragments,
this prevents successful PMTU updates in such case. The next attempts
to send the packet lead to the same tx error. Moreover, vti6 initial
MTU value relies on PMTU adjustments.
This issue can be reproduced with the following LTP test script:
udp_ipsec_vti.sh -6 -p ah -m tunnel -s 2000
Fixes: ccd740cbc6e0 ("vti6: Add pmtu handling to vti6_xmit.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the xdp_umem_get_{data,dma} functions to include/net/xdp_sock.h,
so that the upcoming zero-copy implementation in the Ethernet drivers
can utilize them.
Also, supply some dummy function implementations for
CONFIG_XDP_SOCKETS=n configs.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Export __xdp_rxq_info_unreg_mem_model as xdp_rxq_info_unreg_mem_model,
so it can be used from netdev drivers. Also, add additional checks for
the memory type.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This commit adds proper MEM_TYPE_ZERO_COPY support for
convert_to_xdp_frame. Converting a MEM_TYPE_ZERO_COPY xdp_buff to an
xdp_frame is done by transforming the MEM_TYPE_ZERO_COPY buffer into a
MEM_TYPE_PAGE_ORDER0 frame. This is costly, and in the future it might
make sense to implement a more sophisticated thread-safe alloc/free
scheme for MEM_TYPE_ZERO_COPY, so that no allocation and copy is
required in the fast-path.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When we perform the sg shift repair for the scatterlist ring, we
currently start out at i = first_sg + 1. However, this is not
correct since the first_sg could point to the sge sitting at slot
MAX_SKB_FRAGS - 1, and a subsequent i = MAX_SKB_FRAGS will access
the scatterlist ring (sg) out of bounds. Add the sk_msg_iter_var()
helper for iterating through the ring, and apply the same rule
for advancing to the next ring element as we do elsewhere. Later
work will use this helper also in other places.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
If first_sg and last_sg wraps around in the scatterlist ring, then we
need to account for that in the shift as well. E.g. crafting such msgs
where this is the case leads to a hang as shift becomes negative. E.g.
consider the following scenario:
first_sg := 14 |=> shift := -12 msg->sg_start := 10
last_sg := 3 | msg->sg_end := 5
round 1: i := 15, move_from := 3, sg[15] := sg[ 3]
round 2: i := 0, move_from := -12, sg[ 0] := sg[-12]
round 3: i := 1, move_from := -11, sg[ 1] := sg[-11]
round 4: i := 2, move_from := -10, sg[ 2] := sg[-10]
[...]
round 13: i := 11, move_from := -1, sg[ 2] := sg[ -1]
round 14: i := 12, move_from := 0, sg[ 2] := sg[ 0]
round 15: i := 13, move_from := 1, sg[ 2] := sg[ 1]
round 16: i := 14, move_from := 2, sg[ 2] := sg[ 2]
round 17: i := 15, move_from := 3, sg[ 2] := sg[ 3]
[...]
This means we will loop forever and never hit the msg->sg_end condition
to break out of the loop. When we see that the ring wraps around, then
the shift should be MAX_SKB_FRAGS - first_sg + last_sg - 1. Meaning,
the remainder slots from the tail of the ring and the head until last_sg
combined.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In the current code, msg->data is set as sg_virt(&sg[i]) + start - offset
and msg->data_end relative to it as msg->data + bytes. Using iterator i
to point to the updated starting scatterlist element holds true for some
cases, however not for all where we'd end up pointing out of bounds. It
is /correct/ for these ones:
1) When first finding the starting scatterlist element (sge) where we
find that the page is already privately owned by the msg and where
the requested bytes and headroom fit into the sge's length.
However, it's /incorrect/ for the following ones:
2) After we made the requested area private and updated the newly allocated
page into first_sg slot of the scatterlist ring; when we find that no
shift repair of the ring is needed where we bail out updating msg->data
and msg->data_end. At that point i will point to last_sg, which in this
case is the next elem of first_sg in the ring. The sge at that point
might as well be invalid (e.g. i == msg->sg_end), which we use for
setting the range of sg_virt(&sg[i]). The correct one would have been
first_sg.
3) Similar as in 2) but when we find that a shift repair of the ring is
needed. In this case we fix up all sges and stop once we've reached the
end. In this case i will point to will point to the new msg->sg_end,
and the sge at that point will be invalid. Again here the requested
range sits in first_sg.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This converts the recvmmsg() system call in all its variations to use
'timespec64' internally for its timeout, and have a __kernel_timespec64
argument in the native entry point. This lets us change the type to use
64-bit time_t at a later point while using the 32-bit compat system call
emulation for existing user space.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Using a private template is problematic:
1. We can't assign both a zone and a timeout policy
(zone assigns a conntrack template, so we hit problem 1)
2. Using a template needs to take care of ct refcount, else we'll
eventually free the private template due to ->use underflow.
This patch reworks template policy to instead work with existing conntrack.
As long as such conntrack has not yet been placed into the hash table
(unconfirmed) we can still add the timeout extension.
The only caveat is that we now need to update/correct ct->timeout to
reflect the initial/new state, otherwise the conntrack entry retains the
default 'new' timeout.
Side effect of this change is that setting the policy must
now occur from chains that are evaluated *after* the conntrack lookup
has taken place.
No released kernel contains the timeout policy feature yet, so this change
should be ok.
Changes since v2:
- don't handle 'ct is confirmed case'
- after previous patch, no need to special-case tcp/dccp/sctp timeout
anymore
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
tcp, sctp and dccp trackers re-use the userspace ctnetlink states
to index their timeout arrays, which means timeout[0] is never
used. Copy the 'new' state (syn-sent, dccp-request, ..) to 0 as well
so external users can simply read it off timeouts[0] without need to
differentiate dccp/sctp/tcp and udp/icmp/gre/generic.
The alternative is to map all array accesses to 'i - 1', but that
is a much more intrusive change.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When building building AMSDU from non-linear SKB, we hit a
kernel panic when trying to push the padding to the tail.
Instead, put the padding at the head of the next subframe.
This also fixes the A-MSDU subframes to not have the padding
accounted in the length field and not have pad at all for
the last subframe, both required by the spec.
Fixes: 6e0456b54545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Reviewed-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
IEEE 802.11-2016 14.10.8.3 HWMP sequence numbering says:
If it is a target mesh STA, it shall update its own HWMP SN to
maximum (current HWMP SN, target HWMP SN in the PREQ element) + 1
immediately before it generates a PREP element in response to a
PREQ element.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Modify the API to include all ACK frames in average ACK
signal strength reporting, not just ACKs for data frames.
Make exposing the data conditional on implementing the
extended feature flag.
This is how it was really implemented in mac80211, update
the code there to use the new defines and clean up some of
the setting code.
Keep nl80211.h source compatibility by keeping the old names.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[rewrite commit log, change compatibility to be old=new
instead of the other way around, update kernel-doc,
roll in mac80211 changes, make mac80211 depend on valid
bit instead of HW flag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The current mac80211 WDS (4-address mode) can be used to cover most of the
Multi-AP requirements for Data frames per the WFA Multi-AP Specification v1.0.
When configuring AP/STA interfaces in 4-address mode, they are able to function
as fronthaul AP/backhaul STA of Multi-AP device complying below
Tx, Rx requirements except one missing STA Rx requirement added by this patch.
Multi-AP specification section 14.1 describes the following requirements:
Transmitter requirements
------------------------
1. Fronthaul AP
i) When DA!=RA of backhaul STA, must use 4-address format
ii) When DA==RA of backhaul STA, shall use either 3-address
or 4-address format with RA updated with STA MAC
(mac80211 support 4-address format via AP/VLAN interface)
2. Backhaul STA
i) When SA!=TA of backhaul STA, must use 4-address format
ii) When SA==TA of backhaul STA, shall use either 3-address
or 4-address format with RA updated with AP MAC
(mac80211 support 4-address format via use_4addr)
Receiver requirements
---------------------
1. Fronthaul AP
i) When SA!=TA of backhaul STA, must support receiving 4-address
format frames
ii) When SA==TA of backhaul STA, must support receiving both
3-address and 4-address format frames
(mac80211 support both 3-addr & 4-addr via AP/VLAN interface)
2. Backhaul STA
i) When DA!=RA of backhaul STA, must support receiving 4-address
format frames
ii) When DA==RA of backhaul STA, must support receiving both
3-address and 4-address format frames
(mac80211 support only receiving 4-address format via
use_4addr)
This patch addresses the above Rx requirement (ii) for backhaul STA to receive
unicast (DA==RA) 3-address frames in addition to 4-address frames.
The current design doesn't accept 3-address frames when configured in 4-address
mode (use_4addr). Hence add a check to allow 3-address frames when DA==RA of
backhaul STA (adhering to Table 9-26 of IEEE Std 802.11™-2016).
This case was tested with a bridged station interface when associated with
a non-mac80211 based vendor AP implementation using 3-address frames for WDS.
STA was able to support the Multi-AP Rx requirement when DA==RA. No issues,
no loops seen when tested with mac80211 based AP as well.
Verified and confirmed all other Tx and Rx requirements of AP and STA for
Multi-AP respectively. They all work using the current mac80211-WDS design.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the "offload" attribute is used to create an IPsec SA
and the .xdo_dev_state_add() fails, the SA creation fails.
However, if the "offload" attribute is used on a device that
doesn't offer it, the attribute is quietly ignored and the SA
is created without an offload.
Along the same line of that second case, it would be good to
have a way for the device to refuse to offload an SA without
failing the whole SA creation. This patch adds that feature
by allowing the driver to return -EOPNOTSUPP as a signal that
the SA may be fine, it just can't be offloaded.
This allows the user a little more flexibility in requesting
offloads and not needing to know every detail at all times about
each specific NIC when trying to create SAs.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
The pointer 'esph' is defined but is never used hence it is redundant
and canbe removed.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Fixes the following sparse warning:
net/xfrm/xfrm_interface.c:745:12: warning:
symbol 'xfrmi_get_link_net' was not declared. Should it be static?
Fixes: f203b76d7809 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
While recently going over bpf_msg_pull_data(), I noticed three
issues which are fixed in here:
1) When we attempt to find the first scatterlist element (sge)
for the start offset, we add len to the offset before we check
for start < offset + len, whereas it should come after when
we iterate to the next sge to accumulate the offsets. For
example, given a start offset of 12 with a sge length of 8
for the first sge in the list would lead us to determine this
sge as the first sge thinking it covers first 16 bytes where
start is located, whereas start sits in subsequent sges so
we would end up pulling in the wrong data.
2) After figuring out the starting sge, we have a short-cut test
in !msg->sg_copy[i] && bytes <= len. This checks whether it's
not needed to make the page at the sge private where we can
just exit by updating msg->data and msg->data_end. However,
the length test is not fully correct. bytes <= len checks
whether the requested bytes (end - start offsets) fit into the
sge's length. The part that is missing is that start must not
be sge length aligned. Meaning, the start offset into the sge
needs to be accounted as well on top of the requested bytes
as otherwise we can access the sge out of bounds. For example
the sge could have length of 8, our requested bytes could have
length of 8, but at a start offset of 4, so we also would need
to pull in 4 bytes of the next sge, when we jump to the out
label we do set msg->data to sg_virt(&sg[i]) + start - offset
and msg->data_end to msg->data + bytes which would be oob.
3) The subsequent bytes < copy test for finding the last sge has
the same issue as in point 2) but also it tests for less than
rather than less or equal to. Meaning if the sge length is of
8 and requested bytes of 8 while having the start aligned with
the sge, we would unnecessarily go and pull in the next sge as
well to make it private.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
There are no more users left of the p9_idpool; delete it.
Link: http://lkml.kernel.org/r/20180711210225.19730-7-willy@infradead.org
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
|
|
Replace the custom batch allocation with a slab. Use an IDR to store
pointers to the active requests instead of an array. We don't try to
handle P9_NOTAG specially; the IDR will happily shrink all the way back
once the TVERSION call has completed.
Link: http://lkml.kernel.org/r/20180711210225.19730-6-willy@infradead.org
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
|
|
p9stat_free is more of a cleanup function than a 'free' function as it
only frees the content of the struct; there are chances of use-after-free
if it is improperly used (e.g. p9stat_free called twice as it used to be
possible to)
Clearing dangling pointers makes the function idempotent and safer to use.
Link: http://lkml.kernel.org/r/1535410108-20650-2-git-send-email-asmadeus@codewreck.org
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Reported-by: syzbot+d4252148d198410b864f@syzkaller.appspotmail.com
|
|
freq_reg_info expects to get the frequency in kHz. Instead we
accidently pass it in MHz. Thus, currently the function always
return ERR rule. Fix that.
Fixes: 50f32718e125 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[fix kHz/MHz in commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
TXOP (also known as Channel Occupancy Time) is u16 and should be
added using nla_put_u16 instead of u8, fix that.
Fixes: 50f32718e125 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The current support in the 60GHz band is for channels 1-4.
Add support for channels 5 and 6.
This requires enlarging ieee80211_channel.center_freq from u16 to u32.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes, it is required to stop the transmissions momentarily and
resume it later; stopping the txqs becomes very critical in scenarios where
the packet transmission has to be ceased completely. For example, during
the hardware restart, during off channel operations,
when initiating CSA(upon detecting a radar on the DFS channel), etc.
The TX queue stop/start logic in mac80211 works well in stopping the TX
when drivers make use of netdev queues, i.e, when Qdiscs in network layer
take care of traffic scheduling. Since the devices implementing
wake_tx_queue can run without Qdiscs, packets will be handed to mac80211
directly without queueing them in the netdev queues.
Also, mac80211 does not invoke any of the
netif_stop_*/netif_wake_* APIs if wake_tx_queue is implemented.
Since the queues are not stopped in this case, transmissions can continue
and this will impact negatively on the operation of the wireless device.
For example,
During hardware restart, we stop the netdev queues so that packets are
not sent to the driver. Since ath10k implements wake_tx_queue,
TX queues will not be stopped and packets might reach the hardware while
it is restarting; this can make hardware unresponsive and the only
possible option for recovery is to reboot the entire system.
There is another problem to this, it is observed that the packets
were sent on the DFS channel for a prolonged duration after radar
detection impacting the channel closing time.
We can still invoke netif stop/wake APIs when wake_tx_queue is implemented
but this could lead to packet drops in network layer; adding stop/start
logic for software TXQs in mac80211 instead makes more sense; the change
proposed adds the same in mac80211.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When REGULATORY_COUNTRY_IE_IGNORE is set, __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().
After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().
To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.
Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This came about while trying to determine if there would be any pattern
match on contid, a new audit container identifier internal variable.
This was the only one.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
I changed the way mac80211 updates the PM state of the peer.
I forgot that we could also have multicast frames from the
peer and that those frame should of course not change the
PM state of the peer: A peer goes to power save when it
needs to scan, but it won't send the broadcast Probe Request
with the PM bit set.
This made us mark the peer as awake when it wasn't and then
Intel's firmware would fail to transmit because the peer is
asleep according to its database. The driver warned about
this and it looked like this:
WARNING: CPU: 0 PID: 184 at /usr/src/linux-4.16.14/drivers/net/wireless/intel/iwlwifi/mvm/tx.c:1369 iwl_mvm_rx_tx_cmd+0x53b/0x860
CPU: 0 PID: 184 Comm: irq/124-iwlwifi Not tainted 4.16.14 #1
RIP: 0010:iwl_mvm_rx_tx_cmd+0x53b/0x860
Call Trace:
iwl_pcie_rx_handle+0x220/0x880
iwl_pcie_irq_handler+0x6c9/0xa20
? irq_forced_thread_fn+0x60/0x60
? irq_thread_dtor+0x90/0x90
The relevant code that spits the WARNING is:
case TX_STATUS_FAIL_DEST_PS:
/* the FW should have stopped the queue and not
* return this status
*/
WARN_ON(1);
info->flags |= IEEE80211_TX_STAT_TX_FILTERED;
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199967.
Fixes: 9fef65443388 ("mac80211: always update the PM state of a peer on MGMT / DATA frames")
Cc: <stable@vger.kernel.org> #4.16+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make wmm_rule be part of the reg_rule structure. This simplifies the
code a lot at the cost of having bigger memory usage. However in most
cases we have only few reg_rule's and when we do have many like in
iwlwifi we do not save memory as it allocates a separate wmm_rule for
each channel anyway.
This also fixes a bug reported in various places where somewhere the
pointers were corrupted and we ended up doing a null-dereference.
Fixes: 230ebaa189af ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[rephrase commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mod mask for VHT capabilities intends to say that you can override
the number of STBC receive streams, and it does, but only by accident.
The IEEE80211_VHT_CAP_RXSTBC_X aren't bits to be set, but values (albeit
left-shifted). ORing the bits together gets the right answer, but we
should use the _MASK macro here instead.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Building the newly introduced BPF_PROG_TYPE_SK_REUSEPORT leads to
a compile time error when building with clang:
net/core/filter.o: In function `sk_reuseport_convert_ctx_access':
../net/core/filter.c:7284: undefined reference to `__compiletime_assert_7284'
It seems that clang has issues resolving hweight_long at compile
time. Since SK_FL_PROTO_MASK is a constant, we can use the interface
for known constant arguments which works fine with clang.
Fixes: 2dbb9b9e6df6 ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
In IPv4, the newly introduced rdma_read_gids is used to read the SGID/DGID
for the connection which returns GID correctly for RoCE transport as well.
In IPv6, rdma_read_gids is also used. The following are why rdma_read_gids
is introduced.
rdma_addr_get_dgid() for RoCE for client side connections returns MAC
address, instead of DGID.
rdma_addr_get_sgid() for RoCE doesn't return correct SGID for IPv6 and
when more than one IP address is assigned to the netdevice.
So the transport agnostic rdma_read_gids() API is provided by rdma_cm
module.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 52638f71fcff ("dsa: Move gpio reset into switch driver")
moved the GPIO handling into the switch drivers but forgot
to remove the GPIO header includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function tipc_dest_push, the 32bit variables 'node' and 'port'
are stored separately in uppper and lower part of 64bit 'value'.
Then this value is assigned to dst->value which is a union like:
union
{
struct {
u32 port;
u32 node;
};
u64 value;
}
This works on little-endian machines like x86 but fails on big-endian
machines.
The fix remove the 'value' stack parameter and even the 'value'
member of the union in tipc_dest, assign the 'node' and 'port' member
directly with the input parameter to avoid the endian issue.
Fixes: a80ae5306a73 ("tipc: improve destination linked list")
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When chain 0 was implicitly created, removal of non-existent filter from
chain 0 gave -ENOENT. Once chain 0 became non-implicit, the same call is
giving -EINVAL. Fix this by returning -ENOENT in that case.
Reported-by: Roman Mashak <mrv@mojatatu.com>
Fixes: f71e0ca4db18 ("net: sched: Avoid implicit chain 0 creation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead "Cannot find" say "Cannot create".
Fixes: c35a4acc2985 ("net: sched: cls_api: handle generic cls errors")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After erspan_ver is introudced, if erspan_ver is not set in iproute, its
value will be left 0 by default. Since Commit 02f99df1875c ("erspan: fix
invalid erspan version."), it has broken the traffic due to the version
check in erspan_xmit if users are not aware of 'erspan_ver' param, like
using an old version of iproute.
To fix this compatibility problem, it sets erspan_ver to 1 by default
when adding an erspan dev in erspan_setup. Note that we can't do it in
ipgre_netlink_parms, as this function is also used by ipgre_changelink.
Fixes: 02f99df1875c ("erspan: fix invalid erspan version.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After changing rhashtable_walk_start to return void, start_fail would
never be set other value than 0, and the checking for start_fail is
pointless, so remove it.
Fixes: 97a6ec4ac021 ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Marcelo noticed, in sctp_transport_get_next, it is iterating over
transports but then also accessing the association directly, without
checking any refcnts before that, which can cause an use-after-free
Read.
So fix it by holding transport before accessing the association. With
that, sctp_transport_hold calls can be removed in the later places.
Fixes: 626d16f50f39 ("sctp: export some apis or variables for sctp_diag and reuse some for proc")
Reported-by: syzbot+fe62a0c9aa6a85c6de16@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks.
2) Better fix for AB-BA deadlock in packet scheduler code, from Cong
Wang.
3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel
Borkmann.
4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent
attackers using it as a side-channel. From Eric Dumazet.
5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva.
6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin
Liu.
7) hns and hns3 bug fixes from Huazhong Tan.
8) Fix RIF leak in mlxsw driver, from Ido Schimmel.
9) iova range check fix in vhost, from Jason Wang.
10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend.
11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng.
12) Memory exposure in TCA_U32_SEL handling, from Kees Cook.
13) TCP BBR congestion control fixes from Kevin Yang.
14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger.
15) qed driver fixes from Tomer Tayar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: sched: Fix memory exposure from short TCA_U32_SEL
qed: fix spelling mistake "comparsion" -> "comparison"
vhost: correctly check the iova range when waking virtqueue
qlge: Fix netdev features configuration.
net: macb: do not disable MDIO bus at open/close time
Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
net: macb: Fix regression breaking non-MDIO fixed-link PHYs
mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
i40e: fix condition of WARN_ONCE for stat strings
i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled
ixgbe: fix driver behaviour after issuing VFLR
ixgbe: Prevent unsupported configurations with XDP
ixgbe: Replace GFP_ATOMIC with GFP_KERNEL
igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback()
igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init()
igb: Use an advanced ctx descriptor for launchtime
e1000: ensure to free old tx/rx rings in set_ringparam()
e1000: check on netif_running() before calling e1000_up()
ixgb: use dma_zalloc_coherent instead of allocator/memset
ice: Trivial formatting fixes
...
|
