| Age | Commit message (Collapse) | Author |
|---|
|
The riscv privileged specification mandates to flush the TLB whenever a
page directory is modified, so add that to tlb_flush().
Fixes: c5e9b2c2ae82 ("riscv: Improve tlb_flush()")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Link: https://lore.kernel.org/r/20240128120405.25876-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
If KUnit is built as a module, and it's unloaded, the kunit_bus is not
unregistered. This causes an error if it's then re-loaded later, as we
try to re-register the bus.
Unregister the bus and root_device on shutdown, if it looks valid.
In addition, be more specific about the value of kunit_bus_device. It
is:
- a valid struct device* if the kunit_bus initialised correctly.
- an ERR_PTR if it failed to initialise.
- NULL before initialisation and after shutdown.
Fixes: d03c720e03bd ("kunit: Add APIs for managing devices")
Signed-off-by: David Gow <davidgow@google.com>
Reviewed-by: Rae Moar <rmoar@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
If we are bus manager and the bus has inconsistent gap counts, send a
bus reset immediately instead of trying to read the root node's config
ROM first. Otherwise, we could spend a lot of time trying to read the
config ROM but never succeeding.
This eliminates a 50+ second delay before the FireWire bus is usable after
a newly connected device is powered on in certain circumstances.
The delay occurs if a gap count inconsistency occurs, we are not the root
node, and we become bus manager. One scenario that causes this is with a TI
XIO2213B OHCI, the first time a Sony DSR-25 is powered on after being
connected to the FireWire cable. In this configuration, the Linux box will
not receive the initial PHY configuration packet sent by the DSR-25 as IRM,
resulting in the DSR-25 having a gap count of 44 while the Linux box has a
gap count of 63.
FireWire devices have a gap count parameter, which is set to 63 on power-up
and can be changed with a PHY configuration packet. This determines the
duration of the subaction and arbitration gaps. For reliable communication,
all nodes on a FireWire bus must have the same gap count.
A node may have zero or more of the following roles: root node, bus manager
(BM), isochronous resource manager (IRM), and cycle master. Unless a root
node was forced with a PHY configuration packet, any node might become root
node after a bus reset. Only the root node can become cycle master. If the
root node is not cycle master capable, the BM or IRM should force a change
of root node.
After a bus reset, each node sends a self-ID packet, which contains its
current gap count. A single bus reset does not change the gap count, but
two bus resets in a row will set the gap count to 63. Because a consistent
gap count is required for reliable communication, IEEE 1394a-2000 requires
that the bus manager generate a bus reset if it detects that the gap count
is inconsistent.
When the gap count is inconsistent, build_tree() will notice this after the
self identification process. It will set card->gap_count to the invalid
value 0. If we become bus master, this will force bm_work() to send a bus
reset when it performs gap count optimization.
After a bus reset, there is no bus manager. We will almost always try to
become bus manager. Once we become bus manager, we will first determine
whether the root node is cycle master capable. Then, we will determine if
the gap count should be changed. If either the root node or the gap count
should be changed, we will generate a bus reset.
To determine if the root node is cycle master capable, we read its
configuration ROM. bm_work() will wait until we have finished trying to
read the configuration ROM.
However, an inconsistent gap count can make this take a long time.
read_config_rom() will read the first few quadlets from the config ROM. Due
to the gap count inconsistency, eventually one of the reads will time out.
When read_config_rom() fails, fw_device_init() calls it again until
MAX_RETRIES is reached. This takes 50+ seconds.
Once we give up trying to read the configuration ROM, bm_work() will wake
up, assume that the root node is not cycle master capable, and do a bus
reset. Hopefully, this will resolve the gap count inconsistency.
This change makes bm_work() check for an inconsistent gap count before
waiting for the root node's configuration ROM. If the gap count is
inconsistent, bm_work() will immediately do a bus reset. This eliminates
the 50+ second delay and rapidly brings the bus to a working state.
I considered that if the gap count is inconsistent, a PHY configuration
packet might not be successful, so it could be desirable to skip the PHY
configuration packet before the bus reset in this case. However, IEEE
1394a-2000 and IEEE 1394-2008 say that the bus manager may transmit a PHY
configuration packet before a bus reset when correcting a gap count error.
Since the standard endorses this, I decided it's safe to retain the PHY
configuration packet transmission.
Normally, after a topology change, we will reset the bus a maximum of 5
times to change the root node and perform gap count optimization. However,
if there is a gap count inconsistency, we must always generate a bus reset.
Otherwise the gap count inconsistency will persist and communication will
be unreliable. For that reason, if there is a gap count inconstency, we
generate a bus reset even if we already reached the 5 reset limit.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Reference: https://sourceforge.net/p/linux1394/mailman/message/58727806/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
Drop dirty_log_page_splitting_test's assertion that the number of 4KiB
pages remains the same across dirty logging being enabled and disabled, as
the test doesn't guarantee that mappings outside of the memslots being
dirty logged are stable, e.g. KVM's mappings for code and pages in
memslot0 can be zapped by things like NUMA balancing.
To preserve the spirit of the check, assert that (a) the number of 4KiB
pages after splitting is _at least_ the number of 4KiB pages across all
memslots under test, and (b) the number of hugepages before splitting adds
up to the number of pages across all memslots under test. (b) is a little
tenuous as it relies on memslot0 being incompatible with transparent
hugepages, but that holds true for now as selftests explicitly madvise()
MADV_NOHUGEPAGE for memslot0 (__vm_create() unconditionally specifies the
backing type as VM_MEM_SRC_ANONYMOUS).
Reported-by: Yi Lai <yi1.lai@intel.com>
Reported-by: Tao Su <tao1.su@linux.intel.com>
Reviewed-by: Tao Su <tao1.su@linux.intel.com>
Link: https://lore.kernel.org/r/20240131222728.4100079-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
When finishing the final iteration of dirty_log_test testcase, set
host_quit _before_ the final "continue" so that the vCPU worker doesn't
run an extra iteration, and delete the hack-a-fix of an extra "continue"
from the dirty ring testcase. This fixes a bug where the extra post to
sem_vcpu_cont may not be consumed, which results in failures in subsequent
runs of the testcases. The bug likely was missed during development as
x86 supports only a single "guest mode", i.e. there aren't any subsequent
testcases after the dirty ring test, because for_each_guest_mode() only
runs a single iteration.
For the regular dirty log testcases, letting the vCPU run one extra
iteration is a non-issue as the vCPU worker waits on sem_vcpu_cont if and
only if the worker is explicitly told to stop (vcpu_sync_stop_requested).
But for the dirty ring test, which needs to periodically stop the vCPU to
reap the dirty ring, letting the vCPU resume the guest _after_ the last
iteration means the vCPU will get stuck without an extra "continue".
However, blindly firing off an post to sem_vcpu_cont isn't guaranteed to
be consumed, e.g. if the vCPU worker sees host_quit==true before resuming
the guest. This results in a dangling sem_vcpu_cont, which leads to
subsequent iterations getting out of sync, as the vCPU worker will
continue on before the main task is ready for it to resume the guest,
leading to a variety of asserts, e.g.
==== Test Assertion Failure ====
dirty_log_test.c:384: dirty_ring_vcpu_ring_full
pid=14854 tid=14854 errno=22 - Invalid argument
1 0x00000000004033eb: dirty_ring_collect_dirty_pages at dirty_log_test.c:384
2 0x0000000000402d27: log_mode_collect_dirty_pages at dirty_log_test.c:505
3 (inlined by) run_test at dirty_log_test.c:802
4 0x0000000000403dc7: for_each_guest_mode at guest_modes.c:100
5 0x0000000000401dff: main at dirty_log_test.c:941 (discriminator 3)
6 0x0000ffff9be173c7: ?? ??:0
7 0x0000ffff9be1749f: ?? ??:0
8 0x000000000040206f: _start at ??:?
Didn't continue vcpu even without ring full
Alternatively, the test could simply reset the semaphores before each
testcase, but papering over hacks with more hacks usually ends in tears.
Reported-by: Shaoqin Huang <shahuang@redhat.com>
Fixes: 84292e565951 ("KVM: selftests: Add dirty ring buffer test")
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Link: https://lore.kernel.org/r/20240202231831.354848-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The detection of dirty-throttled tasks in blk-wbt has been subtly broken
since its beginning in 2016. Namely if we are doing cgroup writeback and
the throttled task is not in the root cgroup, balance_dirty_pages() will
set dirty_sleep for the non-root bdi_writeback structure. However
blk-wbt checks dirty_sleep only in the root cgroup bdi_writeback
structure. Thus detection of recently throttled tasks is not working in
this case (we noticed this when we switched to cgroup v2 and suddently
writeback was slow).
Since blk-wbt has no easy way to get to proper bdi_writeback and
furthermore its intention has always been to work on the whole device
rather than on individual cgroups, just move the dirty_sleep timestamp
from bdi_writeback to backing_dev_info. That fixes the checking for
recently throttled task and saves memory for everybody as a bonus.
CC: stable@vger.kernel.org
Fixes: b57d74aff9ab ("writeback: track if we're sleeping on progress in balance_dirty_pages()")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240123175826.21452-1-jack@suse.cz
[axboe: fixup indentation errors]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
commit dfad37051ade ("remap_range: move permission hooks out of
do_clone_file_range()") moved the permission hooks from
do_clone_file_range() out to its caller vfs_clone_file_range(),
but left all the fast sanity checks in do_clone_file_range().
This makes the expensive security hooks be called in situations
that they would not have been called before (e.g. fs does not support
clone).
The only reason for the do_clone_file_range() helper was that overlayfs
did not use to be able to call vfs_clone_file_range() from copy up
context with sb_writers lock held. However, since commit c63e56a4a652
("ovl: do not open/llseek lower file with upper sb_writers held"),
overlayfs just uses an open coded version of vfs_clone_file_range().
Merge_clone_file_range() into vfs_clone_file_range(), restoring the
original order of checks as it was before the regressing commit and adapt
the overlayfs code to call vfs_clone_file_range() before the permission
hooks that were added by commit ca7ab482401c ("ovl: add permission hooks
outside of do_splice_direct()").
Note that in the merge of do_clone_file_range(), the file_start_write()
context was reduced to cover ->remap_file_range() without holding it
over the permission hooks, which was the reason for doing the regressing
commit in the first place.
Reported-and-tested-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202401312229.eddeb9a6-oliver.sang@intel.com
Fixes: dfad37051ade ("remap_range: move permission hooks out of do_clone_file_range()")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/r/20240202102258.1582671-1-amir73il@gmail.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
If a input device is opened before hid_hw_start is called, events may
not be received from the hardware. In the case of USB-backed devices,
for example, the hid_hw_start function is responsible for filling in
the URB which is submitted when the input device is opened. If a device
is opened prematurely, polling will never start because the device will
not have been in the correct state to send the URB.
Because the wacom driver registers its input devices before calling
hid_hw_start, there is a window of time where a device can be opened
and end up in an inoperable state. Some ARM-based Chromebooks in particular
reliably trigger this bug.
This commit splits the wacom_register_inputs function into two pieces.
One which is responsible for setting up the allocated inputs (and runs
prior to hid_hw_start so that devices are ready for any input events
they may end up receiving) and another which only registers the devices
(and runs after hid_hw_start to ensure devices can be immediately opened
without issue). Note that the functions to initialize the LEDs and remotes
are also moved after hid_hw_start to maintain their own dependency chains.
Fixes: 7704ac937345 ("HID: wacom: implement generic HID handling for pen generic devices")
Cc: stable@vger.kernel.org # v3.18+
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
Since commit 680ee411a98e ("HID: logitech-hidpp: Fix connect event race")
the following messages appear in the kernel log from time to time:
logitech-hidpp-device 0003:046D:408A.0005: HID++ 4.5 device connected.
logitech-hidpp-device 0003:046D:408A.0005: HID++ 4.5 device connected.
logitech-hidpp-device 0003:046D:4051.0006: Disconnected
logitech-hidpp-device 0003:046D:408A.0005: Disconnected
As discussed, print the first per-device "device connected" message
at info level, demoting subsequent messages to debug level. Also,
demote the "Disconnected message" to debug level unconditionally.
Link: https://lore.kernel.org/lkml/3277085.44csPzL39Z@natalenko.name/
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fix for v6.8-rc4
This includes one USB4/Thunderbolt fix for v6.8-rc4:
- Correct the CNS (CM TBT3 Not Supported) bit setting for USB4
routers.
This has been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix setting the CNS bit in ROUTER_CS_5
|
|
Emil reports:
After updating Linux on an i.MX28 board, serial communication over
AUART broke. When I TX from the board and measure on the TX pin, it
seems like the HW fifo is not emptied before the transmission is
stopped.
MXS performs weird things with stop_tx(). The driver makes it
conditional on uart_tx_stopped().
So the driver needs special handling. Pass the brand new UART_TX_NOSTOP
to uart_port_tx_flags() and handle the stop on its own.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Emil Kronborg <emil.kronborg@protonmail.com>
Cc: stable <stable@kernel.org>
Fixes: 2d141e683e9a ("tty: serial: use uart_port_tx() helper")
Closes: https://lore.kernel.org/all/miwgbnvy3hjpnricubg76ytpn7xoceehwahupy25bubbduu23s@om2lptpa26xw/
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240201105557.28043-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
And an enum with a flag: UART_TX_NOSTOP. To NOT call
__port->ops->stop_tx() when the circular buffer is empty. mxs-uart needs
this (see the next patch).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: stable <stable@kernel.org>
Tested-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240201105557.28043-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I was reviewing this code again and I realized I made a mistake here.
It should have been > instead of >=. The subtract ensures that we
don't go out of bounds. My patch meant that we don't read the last
chunk of the buffer.
Fixes: 86ee55e9bc7f ("serial: 8250_pci1xxxx: fix off by one in pci1xxxx_process_read_data()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/bd6fb361-bbb9-427d-90e8-a5df4de76221@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DDPP is copied from Synopsys Data book:
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The macro name should be XGMAC_DPP_DISABLE.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240203053133.1129236-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add DRM_IVPU_JOB_STATUS_ABORTED to indicate that the job was aborted
by the driver due to e.g. TDR or user context MMU faults.
This will help UMD and tests distinguish if job was aborted by the FW
or the driver.
Signed-off-by: Grzegorz Trzebiatowski <grzegorz.trzebiatowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126122804.2169129-8-jacek.lawrynowicz@linux.intel.com
|
|
This parameter was never used by the 40xx FW.
Signed-off-by: Krystian Pradzynski <krystian.pradzynski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126122804.2169129-7-jacek.lawrynowicz@linux.intel.com
|
|
All recent 40xx firmware already supports D0i3 entry message and this
WA is no longer needed.
Signed-off-by: Krystian Pradzynski <krystian.pradzynski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126122804.2169129-6-jacek.lawrynowicz@linux.intel.com
|
|
NPU does not require this delay regardless of the generation.
All generations are integrated into the SOC.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126122804.2169129-4-jacek.lawrynowicz@linux.intel.com
|
|
Do not use kernel CIRC_SPACE and CIRC_CNT that
incorrectly return space of a queue when wrap bit was set.
Use correct implementation that compares producer, consumer and
wrap bit values.
Without this fix it was possible to lose events in case when event
queue was full.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126122804.2169129-3-jacek.lawrynowicz@linux.intel.com
|
|
Set AW_SNOOP_OVERRIDE bit in VPU_37/40XX_HOST_IF_TCU_PTW_OVERRIDES
to force snooping for MMU write accesses (setting event queue events).
MMU event queue buffer is the only buffer written by MMU and
mapped as write-back which break cache coherency. Force write
transactions to be snooped solving the problem.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240126122804.2169129-2-jacek.lawrynowicz@linux.intel.com
|
|
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO read-only state. This allows users with GPIOs that
never sleepbeing called in atomic context.
Implement the same mechanism as in commit 52af318c93e97 ("mmc: Allow
non-sleeping GPIO cd").
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240206083912.2543142-1-alexander.stein@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
by BIOS
Driver shall switch clock source from DLL clock to
OPE clock when power off card to ensure that card
can be identified with OPE clock by BIOS.
Signed-off-by: Fred Ai <fred.ai@bayhubtech.com>
Fixes:4be33cf18703 ("mmc: sdhci-pci-o2micro: Improve card input timing at SDR104/HS200 mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240203102908.4683-1-fredaibayhubtech@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
These functions are either used in only one file and can just be
made static or need an #include statement to avoid a warning:
arch/powerpc/platforms/85xx/mpc8536_ds.c:30:13: error: no previous prototype for 'mpc8536_ds_pic_init' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/p1010rdb.c:27:13: error: no previous prototype for 'p1010_rdb_pic_init' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/p1022_ds.c:373:6: error: no previous prototype for 'p1022ds_set_pixel_clock' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/p1022_ds.c:422:1: error: no previous prototype for 'p1022ds_valid_monitor_port' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/p1022_ds.c:435:13: error: no previous prototype for 'p1022_ds_pic_init' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/p1022_rdk.c:43:6: error: no previous prototype for 'p1022rdk_set_pixel_clock' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/p1022_rdk.c:92:1: error: no previous prototype for 'p1022rdk_valid_monitor_port' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/p1022_rdk.c:99:13: error: no previous prototype for 'p1022_rdk_pic_init' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/socrates_fpga_pic.c:273:13: error: no previous prototype for 'socrates_fpga_pic_init' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/xes_mpc85xx.c:40:13: error: no previous prototype for 'xes_mpc85xx_pic_init' [-Werror=missing-prototypes]
arch/powerpc/platforms/85xx/mvme2500.c:24:13: error: no previous prototype for 'mvme2500_pic_init' [-Werror=missing-prototypes]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240123125148.2004648-2-arnd@kernel.org
|
|
ppc64_book3e_allmodconfig has one more driver that triggeres a
few missing-prototypes warnings:
arch/powerpc/sysdev/udbg_memcons.c:44:6: error: no previous prototype for 'memcons_putc' [-Werror=missing-prototypes]
arch/powerpc/sysdev/udbg_memcons.c:57:5: error: no previous prototype for 'memcons_getc_poll' [-Werror=missing-prototypes]
arch/powerpc/sysdev/udbg_memcons.c:80:5: error: no previous prototype for 'memcons_getc' [-Werror=missing-prototypes]
Mark all these function static as there are no other users.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240123125148.2004648-1-arnd@kernel.org
|
|
The hrtimers migration on CPU-down hotplug process has been moved
earlier, before the CPU actually goes to die. This leaves a small window
of opportunity to queue an hrtimer in a blind spot, leaving it ignored.
For example a practical case has been reported with RCU waking up a
SCHED_FIFO task right before the CPUHP_AP_IDLE_DEAD stage, queuing that
way a sched/rt timer to the local offline CPU.
Make sure such situations never go unnoticed and warn when that happens.
Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier")
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240129235646.3171983-4-boqun.feng@gmail.com
|
|
The laptop requires a quirk ID to enable its internal microphone. Add
it to the DMI quirk table.
Reported-by: Stanislav Petrov <stanislav.i.petrov@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216925
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240205214853.2689-1-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Selftests here check not only that connect()/accept() for
TCP-AO/TCP-MD5/non-signed-TCP combinations do/don't establish
connections, but also counters: those are per-AO-key, per-socket and
per-netns.
The counters are checked on the server's side, as the server listener
has TCP-AO/TCP-MD5/no keys for different peers. All tests run in
the same namespaces with the same veth pair, created in test_init().
After close() in both client and server, the sides go through
the regular FIN/ACK + FIN/ACK sequence, which goes in the background.
If the selftest has already started a new testing scenario, read
per-netns counters - it may fail in the end iff it doesn't expect
the TCPAOGood per-netns counters go up during the test.
Let's just kill both TCP-AO sides - that will avoid any asynchronous
background TCP-AO segments going to either sides.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/all/20240201132153.4d68f45e@kernel.org/T/#u
Fixes: 6f0c472a6815 ("selftests/net: Add TCP-AO + TCP-MD5 + no sign listen socket tests")
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20240202-unsigned-md5-netns-counters-v1-1-8b90c37c0566@arista.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
After commit a9ef277488cf ("x86/kvm: Fix SEV check in
sev_map_percpu_data()"), there is a build error when building
x86_64_defconfig with GCOV using LLVM:
ld.lld: error: undefined symbol: cc_vendor
>>> referenced by kvm.c
>>> arch/x86/kernel/kvm.o:(kvm_smp_prepare_boot_cpu) in archive vmlinux.a
which corresponds to
if (cc_vendor != CC_VENDOR_AMD ||
!cc_platform_has(CC_ATTR_GUEST_MEM_ENCRYPT))
return;
Without GCOV, clang is able to eliminate the use of cc_vendor because
cc_platform_has() evaluates to false when CONFIG_ARCH_HAS_CC_PLATFORM is
not set, meaning that if statement will be true no matter what value
cc_vendor has.
With GCOV, the instrumentation keeps the use of cc_vendor around for
code coverage purposes but cc_vendor is only declared, not defined,
without CONFIG_ARCH_HAS_CC_PLATFORM, leading to the build error above.
Provide a macro definition of cc_vendor when CONFIG_ARCH_HAS_CC_PLATFORM
is not set with a value of CC_VENDOR_NONE, so that the first condition
can always be evaluated/eliminated at compile time, avoiding the build
error altogether. This is very similar to the situation prior to
commit da86eb961184 ("x86/coco: Get rid of accessor functions").
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Message-Id: <20240202-provide-cc_vendor-without-arch_has_cc_platform-v1-1-09ad5f2a3099@kernel.org>
Fixes: a9ef277488cf ("x86/kvm: Fix SEV check in sev_map_percpu_data()", 2024-01-31)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
syzbot reported the following general protection fault [1]:
general protection fault, probably for non-canonical address 0xdffffc0000000010: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000080-0x0000000000000087]
...
RIP: 0010:tipc_udp_is_known_peer+0x9c/0x250 net/tipc/udp_media.c:291
...
Call Trace:
<TASK>
tipc_udp_nl_bearer_add+0x212/0x2f0 net/tipc/udp_media.c:646
tipc_nl_bearer_add+0x21e/0x360 net/tipc/bearer.c:1089
genl_family_rcv_msg_doit+0x1fc/0x2e0 net/netlink/genetlink.c:972
genl_family_rcv_msg net/netlink/genetlink.c:1052 [inline]
genl_rcv_msg+0x561/0x800 net/netlink/genetlink.c:1067
netlink_rcv_skb+0x16b/0x440 net/netlink/af_netlink.c:2544
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1076
netlink_unicast_kernel net/netlink/af_netlink.c:1341 [inline]
netlink_unicast+0x53b/0x810 net/netlink/af_netlink.c:1367
netlink_sendmsg+0x8b7/0xd70 net/netlink/af_netlink.c:1909
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
____sys_sendmsg+0x6ac/0x940 net/socket.c:2584
___sys_sendmsg+0x135/0x1d0 net/socket.c:2638
__sys_sendmsg+0x117/0x1e0 net/socket.c:2667
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
The cause of this issue is that when tipc_nl_bearer_add() is called with
the TIPC_NLA_BEARER_UDP_OPTS attribute, tipc_udp_nl_bearer_add() is called
even if the bearer is not UDP.
tipc_udp_is_known_peer() called by tipc_udp_nl_bearer_add() assumes that
the media_ptr field of the tipc_bearer has an udp_bearer type object, so
the function goes crazy for non-UDP bearers.
This patch fixes the issue by checking the bearer type before calling
tipc_udp_nl_bearer_add() in tipc_nl_bearer_add().
Fixes: ef20cd4dd163 ("tipc: introduce UDP replicast")
Reported-and-tested-by: syzbot+5142b87a9abc510e14fa@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=5142b87a9abc510e14fa [1]
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Link: https://lore.kernel.org/r/20240131152310.4089541-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Pull bcachefs fixes from Kent Overstreet:
"Two serious ones here that we'll want to backport to stable: a fix for
a race in the thread_with_file code, and another locking fixup in the
subvolume deletion path"
* tag 'bcachefs-2024-02-05' of https://evilpiepirate.org/git/bcachefs:
bcachefs: time_stats: Check for last_event == 0 when updating freq stats
bcachefs: install fd later to avoid race with close
bcachefs: unlock parent dir if entry is not found in subvolume deletion
bcachefs: Fix build on parisc by avoiding __multi3()
|
|
The vDSO executes in userspace, so the kernel's UBSAN should not
instrument it. Solves these kind of build errors:
loongarch64-linux-ld: arch/loongarch/vdso/vgettimeofday.o: in function `vdso_shift_ns':
lib/vdso/gettimeofday.c:23:(.text+0x3f8): undefined reference to `__ubsan_handle_shift_out_of_bounds'
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401310530.lZHCj1Zl-lkp@intel.com/
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: WANG Xuerui <kernel@xen0n.name>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Fangrui Song <maskray@google.com>
Cc: loongarch@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The earlycon parameter is based on fixmap, and fixmap addresses are not
supposed to be shadowed by KASAN. So return the kasan_early_shadow_page
in kasan_mem_to_shadow() if the input address is above FIXADDR_START.
Otherwise earlycon cannot work after kasan_init().
Cc: stable@vger.kernel.org
Fixes: 5aa4ac64e6add3e ("LoongArch: Add KASAN (Kernel Address Sanitizer) support")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
With default config, the value of NR_CPUS is 64. When HW platform has
more then 64 cpus, system will crash on these platforms. MAX_CORE_PIC
is the maximum cpu number in MADT table (max physical number) which can
exceed the supported maximum cpu number (NR_CPUS, max logical number),
but kernel should not crash. Kernel should boot cpus with NR_CPUS, let
the remainder cpus stay in BIOS.
The potential crash reason is that the array acpi_core_pic[NR_CPUS] can
be overflowed when parsing MADT table, and it is obvious that CORE_PIC
should be corresponding to physical core rather than logical core, so it
is better to define the array as acpi_core_pic[MAX_CORE_PIC].
With the patch, system can boot up 64 vcpus with qemu parameter -smp 128,
otherwise system will crash with the following message.
[ 0.000000] CPU 0 Unable to handle kernel paging request at virtual address 0000420000004259, era == 90000000037a5f0c, ra == 90000000037a46ec
[ 0.000000] Oops[#1]:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 6.8.0-rc2+ #192
[ 0.000000] Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022
[ 0.000000] pc 90000000037a5f0c ra 90000000037a46ec tp 9000000003c90000 sp 9000000003c93d60
[ 0.000000] a0 0000000000000019 a1 9000000003d93bc0 a2 0000000000000000 a3 9000000003c93bd8
[ 0.000000] a4 9000000003c93a74 a5 9000000083c93a67 a6 9000000003c938f0 a7 0000000000000005
[ 0.000000] t0 0000420000004201 t1 0000000000000000 t2 0000000000000001 t3 0000000000000001
[ 0.000000] t4 0000000000000003 t5 0000000000000000 t6 0000000000000030 t7 0000000000000063
[ 0.000000] t8 0000000000000014 u0 ffffffffffffffff s9 0000000000000000 s0 9000000003caee98
[ 0.000000] s1 90000000041b0480 s2 9000000003c93da0 s3 9000000003c93d98 s4 9000000003c93d90
[ 0.000000] s5 9000000003caa000 s6 000000000a7fd000 s7 000000000f556b60 s8 000000000e0a4330
[ 0.000000] ra: 90000000037a46ec platform_init+0x214/0x250
[ 0.000000] ERA: 90000000037a5f0c efi_runtime_init+0x30/0x94
[ 0.000000] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
[ 0.000000] PRMD: 00000000 (PPLV0 -PIE -PWE)
[ 0.000000] EUEN: 00000000 (-FPE -SXE -ASXE -BTE)
[ 0.000000] ECFG: 00070800 (LIE=11 VS=7)
[ 0.000000] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
[ 0.000000] BADV: 0000420000004259
[ 0.000000] PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
[ 0.000000] Modules linked in:
[ 0.000000] Process swapper (pid: 0, threadinfo=(____ptrval____), task=(____ptrval____))
[ 0.000000] Stack : 9000000003c93a14 9000000003800898 90000000041844f8 90000000037a46ec
[ 0.000000] 000000000a7fd000 0000000008290000 0000000000000000 0000000000000000
[ 0.000000] 0000000000000000 0000000000000000 00000000019d8000 000000000f556b60
[ 0.000000] 000000000a7fd000 000000000f556b08 9000000003ca7700 9000000003800000
[ 0.000000] 9000000003c93e50 9000000003800898 9000000003800108 90000000037a484c
[ 0.000000] 000000000e0a4330 000000000f556b60 000000000a7fd000 000000000f556b08
[ 0.000000] 9000000003ca7700 9000000004184000 0000000000200000 000000000e02b018
[ 0.000000] 000000000a7fd000 90000000037a0790 9000000003800108 0000000000000000
[ 0.000000] 0000000000000000 000000000e0a4330 000000000f556b60 000000000a7fd000
[ 0.000000] 000000000f556b08 000000000eaae298 000000000eaa5040 0000000000200000
[ 0.000000] ...
[ 0.000000] Call Trace:
[ 0.000000] [<90000000037a5f0c>] efi_runtime_init+0x30/0x94
[ 0.000000] [<90000000037a46ec>] platform_init+0x214/0x250
[ 0.000000] [<90000000037a484c>] setup_arch+0x124/0x45c
[ 0.000000] [<90000000037a0790>] start_kernel+0x90/0x670
[ 0.000000] [<900000000378b0d8>] kernel_entry+0xd8/0xdc
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
LoongArch missed the refactoring made by commit 282a181b1a0d ("seccomp:
Move config option SECCOMP to arch/Kconfig") because LoongArch was not
mainlined at that time.
The 'depends on PROC_FS' statement is stale as described in that commit.
Select HAVE_ARCH_SECCOMP, and remove the duplicated config entry.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
ARCH_ENABLE_THP_MIGRATION is supposed to be selected by arch Kconfig.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Rather then loop over entities until one with a ready job is found,
re-queue the run job worker when drm_sched_entity_pop_job() returns NULL.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Fixes: 66dbd9004a55 ("drm/sched: Drain all entities in DRM sched run job worker")
Reviewed-by: Luben Tuikov <ltuikov89@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240130030413.2031009-1-matthew.brost@intel.com
|
|
workqueue_apply_unbound_cpumask()"
This reverts commit ca10d851b9ad0338c19e8e3089e24d565ebfffd7.
The commit allowed workqueue_apply_unbound_cpumask() to clear __WQ_ORDERED
on now removed implicitly ordered workqueues. This was incorrect in that
system-wide config change shouldn't break ordering properties of all
workqueues. The reason why apply_workqueue_attrs() path was allowed to do so
was because it was targeting the specific workqueue - either the workqueue
had WQ_SYSFS set or the workqueue user specifically tried to change
max_active, both of which indicate that the workqueue doesn't need to be
ordered.
The implicitly ordered workqueue promotion was removed by the previous
commit 3bc1e711c26b ("workqueue: Don't implicitly make UNBOUND workqueues w/
@max_active==1 ordered"). However, it didn't update this path and broke
build. Let's revert the commit which was incorrect in the first place which
also fixes build.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 3bc1e711c26b ("workqueue: Don't implicitly make UNBOUND workqueues w/ @max_active==1 ordered")
Fixes: ca10d851b9ad ("workqueue: Override implicit ordered attribute in workqueue_apply_unbound_cpumask()")
Cc: stable@vger.kernel.org # v6.6+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
If ufshcd_err_handler() is called in a suspend/resume situation,
ufs_release() can be called twice and active_reqs end up going negative.
This is because ufshcd_err_handling_prepare() and
ufshcd_err_handling_unprepare() both call ufshcd_release().
Remove superfluous call to ufshcd_release().
Signed-off-by: SEO HOYOUNG <hy50.seo@samsung.com>
Link: https://lore.kernel.org/r/20240122083324.11797-1-hy50.seo@samsung.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When task_tag >= 32 (in MCQ mode) and sizeof(unsigned int) == 4, 1U <<
task_tag will out of bounds for a u32 mask. Fix this up to prevent
SHIFT_ISSUE (bitwise shifts that are out of bounds for their data type).
[name:debug_monitors&]Unexpected kernel BRK exception at EL1
[name:traps&]Internal error: BRK handler: 00000000f2005514 [#1] PREEMPT SMP
[name:mediatek_cpufreq_hw&]cpufreq stop DVFS log done
[name:mrdump&]Kernel Offset: 0x1ba5800000 from 0xffffffc008000000
[name:mrdump&]PHYS_OFFSET: 0x80000000
[name:mrdump&]pstate: 22400005 (nzCv daif +PAN -UAO)
[name:mrdump&]pc : [0xffffffdbaf52bb2c] ufshcd_clear_cmd+0x280/0x288
[name:mrdump&]lr : [0xffffffdbaf52a774] ufshcd_wait_for_dev_cmd+0x3e4/0x82c
[name:mrdump&]sp : ffffffc0081471b0
<snip>
Workqueue: ufs_eh_wq_0 ufshcd_err_handler
Call trace:
dump_backtrace+0xf8/0x144
show_stack+0x18/0x24
dump_stack_lvl+0x78/0x9c
dump_stack+0x18/0x44
mrdump_common_die+0x254/0x480 [mrdump]
ipanic_die+0x20/0x30 [mrdump]
notify_die+0x15c/0x204
die+0x10c/0x5f8
arm64_notify_die+0x74/0x13c
do_debug_exception+0x164/0x26c
el1_dbg+0x64/0x80
el1h_64_sync_handler+0x3c/0x90
el1h_64_sync+0x68/0x6c
ufshcd_clear_cmd+0x280/0x288
ufshcd_wait_for_dev_cmd+0x3e4/0x82c
ufshcd_exec_dev_cmd+0x5bc/0x9ac
ufshcd_verify_dev_init+0x84/0x1c8
ufshcd_probe_hba+0x724/0x1ce0
ufshcd_host_reset_and_restore+0x260/0x574
ufshcd_reset_and_restore+0x138/0xbd0
ufshcd_err_handler+0x1218/0x2f28
process_one_work+0x5fc/0x1140
worker_thread+0x7d8/0xe20
kthread+0x25c/0x468
ret_from_fork+0x10/0x20
Signed-off-by: Alice Chao <alice.chao@mediatek.com>
Link: https://lore.kernel.org/r/20240205104905.24929-1-alice.chao@mediatek.com
Reviewed-by: Stanley Jhu <chu.stanley@gmail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
LUNs going into "failed ready running" state observed on >1T and on even
numbers of size (2T, 4T, 6T, 8T and 10T). The issue occurs when DIF is
enabled at the host.
The kernel logs:
Cannot setup S/G List for HBAIO segs 1/1 SGL 512 SCSI 256: 3 0
The host lpfc driver is failing to setup scatter/gather list (protection
data) for the I/Os.
The return type lpfc_bg_setup_sgl()/lpfc_bg_setup_sgl_prot() causes the
compiler to remove the most significant bit. Use an unsigned type instead.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[dwagner: added commit message]
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Link: https://lore.kernel.org/r/20231220162658.12392-1-dwagner@suse.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 4373534a9850 ("scsi: core: Move scsi_host_busy() out of host lock
for waking up EH handler") intended to fix a hard lockup issue triggered by
EH. The core idea was to move scsi_host_busy() out of the host lock when
processing individual commands for EH. However, a suggested style change
inadvertently caused scsi_host_busy() to remain under the host lock. Fix
this by calling scsi_host_busy() outside the lock.
Fixes: 4373534a9850 ("scsi: core: Move scsi_host_busy() out of host lock for waking up EH handler")
Cc: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20240203024521.2006455-1-ming.lei@redhat.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 6abe9c1386e5 ("KVM: X86: Move ignore_msrs handling upper the
stack") changed the 'ignore_msrs' handling, including sanitizing return
values to the caller. This was fine until commit 12bc2132b15e ("KVM:
X86: Do the same ignore_msrs check for feature msrs") which allowed
non-existing feature MSRs to be ignored, i.e. to not generate an error
on the ioctl() level. It even tried to preserve the sanitization of the
return value. However, the logic is flawed, as '*data' will be
overwritten again with the uninitialized stack value of msr.data.
Fix this by simplifying the logic and always initializing msr.data,
vanishing the need for an additional error exit path.
Fixes: 12bc2132b15e ("KVM: X86: Do the same ignore_msrs check for feature msrs")
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Link: https://lore.kernel.org/r/20240203124522.592778-2-minipli@grsecurity.net
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Copy cck and ofdm separately in order to avoid __read_overflow2_field
warning.
Fixes: f75e4779d215 ("wifi: mt76: mt7996: add txpower setting support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240203132446.54790-1-nbd@nbd.name
|
|
Function nvkm_gsp_radix3_sg() uses nvkm_gsp_mem objects to allocate the
radix3 tables, but it unnecessarily creates those objects manually
instead of using the standard nvkm_gsp_mem_ctor() function like the
rest of the code does.
Signed-off-by: Timur Tabi <ttabi@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202230608.1981026-2-ttabi@nvidia.com
|
|
Nouveau manages GSP-RM DMA buffers with nvkm_gsp_mem objects. Several of
these buffers are never dealloced. Some of them can be deallocated
right after GSP-RM is initialized, but the rest need to stay until the
driver unloads.
Also futher bullet-proof these objects by poisoning the buffer and
clearing the nvkm_gsp_mem object when it is deallocated. Poisoning
the buffer should trigger an error (or crash) from GSP-RM if it tries
to access the buffer after we've deallocated it, because we were wrong
about when it is safe to deallocate.
Finally, change the mem->size field to a size_t because that's the same
type that dma_alloc_coherent expects.
Cc: <stable@vger.kernel.org> # v6.7
Fixes: 176fdcbddfd2 ("drm/nouveau/gsp/r535: add support for booting GSP-RM")
Signed-off-by: Timur Tabi <ttabi@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202230608.1981026-1-ttabi@nvidia.com
|
|
Timur pointed this out before, and it just slipped my mind,
but this might help some things work better, around pcie power
management.
Cc: <stable@vger.kernel.org> # v6.7
Fixes: 8d55b0a940bb ("nouveau/gsp: add some basic registry entries.")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240130032643.2498315-1-airlied@gmail.com
|
|
The example for PCI devices has some addressing errors. 'reg' is written
as if the parent bus is PCI, but the default bus for examples is 1
address and size cell. 'ranges' is defining config space with a
size of 0. Generally, config space should not be defined in
'ranges', only PCI memory and I/O spaces. Fix these issues by updating
the values with made-up, but valid values.
This was uncovered with recent dtschema changes.
Link: https://lore.kernel.org/r/20240122173514.935742-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
A recent change to check_for_locks() changed it to take ->flc_lock while
holding ->fi_lock. This creates a lock inversion (reported by lockdep)
because there is a case where ->fi_lock is taken while holding
->flc_lock.
->flc_lock is held across ->fl_lmops callbacks, and
nfsd_break_deleg_cb() is one of those and does take ->fi_lock. However
it doesn't need to.
Prior to v4.17-rc1~110^2~22 ("nfsd: create a separate lease for each
delegation") nfsd_break_deleg_cb() would walk the ->fi_delegations list
and so needed the lock. Since then it doesn't walk the list and doesn't
need the lock.
Two actions are performed under the lock. One is to call
nfsd_break_one_deleg which calls nfsd4_run_cb(). These doesn't act on
the nfs4_file at all, so don't need the lock.
The other is to set ->fi_had_conflict which is in the nfs4_file.
This field is only ever set here (except when initialised to false)
so there is no possible problem will multiple threads racing when
setting it.
The field is tested twice in nfs4_set_delegation(). The first test does
not hold a lock and is documented as an opportunistic optimisation, so
it doesn't impose any need to hold ->fi_lock while setting
->fi_had_conflict.
The second test in nfs4_set_delegation() *is* make under ->fi_lock, so
removing the locking when ->fi_had_conflict is set could make a change.
The change could only be interesting if ->fi_had_conflict tested as
false even though nfsd_break_one_deleg() ran before ->fi_lock was
unlocked. i.e. while hash_delegation_locked() was running.
As hash_delegation_lock() doesn't interact in any way with nfs4_run_cb()
there can be no importance to this interaction.
So this patch removes the locking from nfsd_break_one_deleg() and moves
the final test on ->fi_had_conflict out of the locked region to make it
clear that locking isn't important to the test. It is still tested
*after* vfs_setlease() has succeeded. This might be significant and as
vfs_setlease() takes ->flc_lock, and nfsd_break_one_deleg() is called
under ->flc_lock this "after" is a true ordering provided by a spinlock.
Fixes: edcf9725150e ("nfsd: fix RELEASE_LOCKOWNER")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
For DMA mode, the bus width of the DMA is equal to the size of data
word, so burst length should be configured as bits per word.
For CPU mode, because of the spi transfer len is in byte, so calculate
the total number of words according to spi transfer len and bits per
word, burst length should be configured as total data bits.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Fixes: e9b220aeacf1 ("spi: spi-imx: correctly configure burst length when using dma")
Fixes: 5f66db08cbd3 ("spi: imx: Take in account bits per word instead of assuming 8-bits")
Link: https://lore.kernel.org/r/20240204091912.36488-1-carlos.song@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The tascodec_init() of the snd-soc-tas2781-comlib module is called from
snd-soc-tas2781-i2c and snd-hda-scodec-tas2781-i2c modules. It calls
request_firmware_nowait() with parameter THIS_MODULE and a cont/callback
from the latter modules.
The latter modules can be removed while their callbacks are running,
resulting in a general protection failure.
Add module parameter to tascodec_init() so request_firmware_nowait() can
be called with the module of the callback.
Fixes: ef3bcde75d06 ("ASoC: tas2781: Add tas2781 driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/118dad922cef50525e5aab09badef2fa0eb796e5.1707076603.git.soyer@irl.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
|
