| Age | Commit message (Collapse) | Author |
|---|
|
The user would be confused while facing a error commit without
any error report.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494596-7090-1-git-send-email-mark.yao@rock-chips.com
|
|
VOP pitch register is word align, need align to word.
VOP_WIN0_VIR:
bit[31:16] win0_vir_stride_uv
Number of words of Win0 uv Virtual width
bit[15:0] win0_vir_width
Number of words of Win0 yrgb Virtual width
ARGB888 : win0_vir_width
RGB888 : (win0_vir_width*3/4) + (win0_vir_width%3)
RGB565 : ceil(win0_vir_width/2)
YUV : ceil(win0_vir_width/4)
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494591-7034-1-git-send-email-mark.yao@rock-chips.com
|
|
fixup the scale calculation formula on the case
src_height == (dst_height/2).
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494586-6984-1-git-send-email-mark.yao@rock-chips.com
|
|
Iommu would get page fault with following path:
vop_disable:
1, disable all windows and set vop config done
2, vop enter to standy, all windows not works, but their registers
are not clean, when you read window's enable bit, may found the
window is enable.
vop_enable:
1, memcpy(vop->regsbak, vop->regs, len)
save current vop registers to vop->regsbak, then you can found
window is enable on regsbak.
2, VOP_WIN_SET(vop, win, gate, 1);
force enable window gate, but gate and enable are on same
hardware register, then window enable bit rewrite to vop hardware.
3, vop power on, and vop might try to scan destroyed buffer,
then iommu get page fault.
Move windows disable after vop regsbak restore, then vop regsbak mechanism
would keep tracing the modify, everything would be safe.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494582-6934-1-git-send-email-mark.yao@rock-chips.com
|
|
If the decrementer wraps again and de-asserts the decrementer
exception while hard-disabled, __check_irq_replay() has a test to
notice the wrap when interrupts are re-enabled.
The decrementer check must be done when clearing the PACA_IRQ_HARD_DIS
flag, not when the PACA_IRQ_DEC flag is tested. Previously this worked
because the decrementer interrupt was always the first one checked
after clearing the hard disable flag, but HMI check was moved ahead of
that, which introduced this bug.
This can cause a missed decrementer interrupt if we soft-disable
interrupts then take an HMI which is recorded in irq_happened, then
hard-disable interrupts for > 4s to wrap the decrementer.
Fixes: e0e0d6b7390b ("powerpc/64: Replay hypervisor maintenance interrupt first")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
POWER9 DD2 PMU can stop after a state-loss idle in some conditions.
A solution is to set then clear MMCRA[60] after wake from state-loss
idle. MMCRA[60] is a non-architected bit, see the user manual for
details.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
into drm-fixes
Just a few small fixes for 4.13.
* 'drm-fixes-4.13' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Use list_del_init in amdgpu_mn_unregister
drm/amdgpu: Fix undue fallthroughs in golden registers initialization
drm/amdgpu: fix header on gfx9 clear state
|
|
Neal Cardwell says:
====================
tcp: fix xmit timer rearming to avoid stalls
This patch series is a bug fix for a TCP loss recovery performance bug
reported independently in recent netdev threads:
(i) July 26, 2017: netdev thread "TCP fast retransmit issues"
(ii) July 26, 2017: netdev thread:
"[PATCH V2 net-next] TLP: Don't reschedule PTO when there's one
outstanding TLP retransmission"
Many thanks to Klavs Klavsen and Mao Wenan for the detailed reports,
traces, and packetdrill test cases, which enabled us to root-cause
this issue and verify the fix.
- v1 -> v2:
- In patch 2/3, changed an unclear comment in the pre-existing code
in tcp_schedule_loss_probe() to be more clear (thanks to Eric Dumazet
for suggesting we improve this).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a TCP loss recovery performance bug raised recently on the netdev
list, in two threads:
(i) July 26, 2017: netdev thread "TCP fast retransmit issues"
(ii) July 26, 2017: netdev thread:
"[PATCH V2 net-next] TLP: Don't reschedule PTO when there's one
outstanding TLP retransmission"
The basic problem is that incoming TCP packets that did not indicate
forward progress could cause the xmit timer (TLP or RTO) to be rearmed
and pushed back in time. In certain corner cases this could result in
the following problems noted in these threads:
- Repeated ACKs coming in with bogus SACKs corrupted by middleboxes
could cause TCP to repeatedly schedule TLPs forever. We kept
sending TLPs after every ~200ms, which elicited bogus SACKs, which
caused more TLPs, ad infinitum; we never fired an RTO to fill in
the holes.
- Incoming data segments could, in some cases, cause us to reschedule
our RTO or TLP timer further out in time, for no good reason. This
could cause repeated inbound data to result in stalls in outbound
data, in the presence of packet loss.
This commit fixes these bugs by changing the TLP and RTO ACK
processing to:
(a) Only reschedule the xmit timer once per ACK.
(b) Only reschedule the xmit timer if tcp_clean_rtx_queue() deems the
ACK indicates sufficient forward progress (a packet was
cumulatively ACKed, or we got a SACK for a packet that was sent
before the most recent retransmit of the write queue head).
This brings us back into closer compliance with the RFCs, since, as
the comment for tcp_rearm_rto() notes, we should only restart the RTO
timer after forward progress on the connection. Previously we were
restarting the xmit timer even in these cases where there was no
forward progress.
As a side benefit, this commit simplifies and speeds up the TCP timer
arming logic. We had been calling inet_csk_reset_xmit_timer() three
times on normal ACKs that cumulatively acknowledged some data:
1) Once near the top of tcp_ack() to switch from TLP timer to RTO:
if (icsk->icsk_pending == ICSK_TIME_LOSS_PROBE)
tcp_rearm_rto(sk);
2) Once in tcp_clean_rtx_queue(), to update the RTO:
if (flag & FLAG_ACKED) {
tcp_rearm_rto(sk);
3) Once in tcp_ack() after tcp_fastretrans_alert() to switch from RTO
to TLP:
if (icsk->icsk_pending == ICSK_TIME_RETRANS)
tcp_schedule_loss_probe(sk);
This commit, by only rescheduling the xmit timer once per ACK,
simplifies the code and reduces CPU overhead.
This commit was tested in an A/B test with Google web server
traffic. SNMP stats and request latency metrics were within noise
levels, substantiating that for normal web traffic patterns this is a
rare issue. This commit was also tested with packetdrill tests to
verify that it fixes the timer behavior in the corner cases discussed
in the netdev threads mentioned above.
This patch is a bug fix patch intended to be queued for -stable
relases.
Fixes: 6ba8a3b19e76 ("tcp: Tail loss probe (TLP)")
Reported-by: Klavs Klavsen <kl@vsen.dk>
Reported-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Have tcp_schedule_loss_probe() base the TLP scheduling decision based
on when the RTO *should* fire. This is to enable the upcoming xmit
timer fix in this series, where tcp_schedule_loss_probe() cannot
assume that the last timer installed was an RTO timer (because we are
no longer doing the "rearm RTO, rearm RTO, rearm TLP" dance on every
ACK). So tcp_schedule_loss_probe() must independently figure out when
an RTO would want to fire.
In the new TLP implementation following in this series, we cannot
assume that icsk_timeout was set based on an RTO; after processing a
cumulative ACK the icsk_timeout we see can be from a previous TLP or
RTO. So we need to independently recalculate the RTO time (instead of
reading it out of icsk_timeout). Removing this dependency on the
nature of icsk_timeout makes things a little easier to reason about
anyway.
Note that the old and new code should be equivalent, since they are
both saying: "if the RTO is in the future, but at an earlier time than
the normal TLP time, then set the TLP timer to fire when the RTO would
have fired".
Fixes: 6ba8a3b19e76 ("tcp: Tail loss probe (TLP)")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pure refactor. This helper will be required in the xmit timer fix
later in the patch series. (Because the TLP logic will want to make
this calculation.)
Fixes: 6ba8a3b19e76 ("tcp: Tail loss probe (TLP)")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull VFIO fixes from Alex Williamson:
- SPAPR/EEH config build fix (Murilo Opsfelder Araujo)
- Fix possible device lock deadlock (Alex Williamson)
- Correctly size integrated endpoint PCIe capabilities (Alex
Williamson)
* tag 'vfio-v4.13-rc4' of git://github.com/awilliam/linux-vfio:
vfio/pci: Fix handling of RC integrated endpoint PCIe capability size
vfio/pci: Use pci_try_reset_function() on initial open
include/linux/vfio.h: Guard powerpc-specific functions with CONFIG_VFIO_SPAPR_EEH
|
|
The function acpi_dev_get_resources() is completely generic and
can be used to parse resource objects that are not necessarily
coming from the _CRS method but also from other objects eg _DMA
that have the same _CRS resource format.
Create an acpi_dev_get_resources() helper, internal to the ACPI
resources parsing compilation unit, __acpi_dev_get_resources(),
that takes a const char* parameter to detect which ACPI method should be
called to retrieve the resources list and make acpi_dev_get_resources()
call it with a method name _CRS leaving the API behaviour unchanged.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
After commit c2ed1880fd61 ("net: ipv6: check route protocol when
deleting routes"), ipv6 route checks rt protocol when trying to
remove a rt entry.
It introduced a side effect causing 'ip -6 route flush cache' not
to work well. When flushing caches with iproute, all route caches
get dumped from kernel then removed one by one by sending DELROUTE
requests to kernel for each cache.
The thing is iproute sends the request with the cache whose proto
is set with RTPROT_REDIRECT by rt6_fill_node() when kernel dumps
it. But in kernel the rt_cache protocol is still 0, which causes
the cache not to be matched and removed.
So the real reason is rt6i_protocol in the route is not set when
it is allocated. As David Ahern's suggestion, this patch is to
set rt6i_protocol properly in the route when it is installed and
remove the codes setting rtm_protocol according to rt6i_flags in
rt6_fill_node.
This is also an improvement to keep rt6i_protocol consistent with
rtm_protocol.
Fixes: c2ed1880fd61 ("net: ipv6: check route protocol when deleting routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge misc fixes from Andrew Morton:
"15 fixes"
[ This does not merge the "fortify: use WARN instead of BUG for now"
patch, which needs a bit of extra work to build cleanly with all
configurations. Arnd is on it. - Linus ]
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
ocfs2: don't clear SGID when inheriting ACLs
mm: allow page_cache_get_speculative in interrupt context
userfaultfd: non-cooperative: flush event_wqh at release time
ipc: add missing container_of()s for randstruct
cpuset: fix a deadlock due to incomplete patching of cpusets_enabled()
userfaultfd_zeropage: return -ENOSPC in case mm has gone
mm: take memory hotplug lock within numa_zonelist_order_handler()
mm/page_io.c: fix oops during block io poll in swapin path
zram: do not free pool->size_class
kthread: fix documentation build warning
kasan: avoid -Wmaybe-uninitialized warning
userfaultfd: non-cooperative: notify about unmap of destination during mremap
mm, mprotect: flush TLB if potentially racing with a parallel reclaim leaving stale TLB entries
pid: kill pidhash_size in pidhash_init()
mm/hugetlb.c: __get_user_pages ignores certain follow_hugetlb_page errors
|
|
ACPICA commit 50f61636543a55d143c792a4814da7700a7fafc2
Version 20170728.
Link: https://github.com/acpica/acpica/commit/50f61636
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit f3300640c63df138d133740b54e2c0a1befa4086
This reverts commit c8eac10178b387f9eb1935694e509d4518da77bb.
Link: https://github.com/acpica/acpica/commit/f3300640
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit af661c00afac7aa481a961fa48c6540a99ad64a6
The _DMA object contains a resource template, this change
adds support for the walk resources function so that ACPI
devices containing a _DMA object can actually parse it to
detect DMA ranges for the respective bus.
Link: https://github.com/acpica/acpica/commit/af661c00
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit ea9152daaec30760fa4c25285998f58233ec0db5
This exception is only meaningful with an associated error message.
Link: https://github.com/acpica/acpica/commit/ea9152da
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 0c08790c56fdf0dc081ae869495a09d8c4230854
This change defers the resolution of package elements that
are named references until after the entire namespace has been
loaded from the definition block. This allows such references
to be in fact forward references for both module level code
and control methods.
Link: https://github.com/acpica/acpica/commit/0c08790c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 916993dbcd45b46e01f6c9b8337a01513f5d8dcc
Properly resolve alias objects for display.
General cleanup of related output.
Link: https://github.com/acpica/acpica/commit/916993db
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 719d0bdd48e3e8e7a62a86c04922b9f41da6def0
Provide common creation code for the Alias operator. All objects
are now handled the same, with the only exception being the
Method() operator. It has a special internal Alias type.
Link: https://github.com/acpica/acpica/commit/719d0bdd
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit a7c6d65a5dab20b1e191c197e09af337fc54b341
/WX turns warning into fatal erros for MSVC builds. We need /WX- during
EDK2 porting to allow agile development.
Now it is time to enable /WX and some explicit type conversion cleanups
are required for enabling /WX. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/a7c6d65a
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 343fc31840d40c06001f3b170ee5bcdfd3c7f3e0
ACPI spec allows to configure different 32-bit/64-bit table addresses for
DSDT and FACS. And for FACS, it's meaningful to dump both of them as they
are used to support different suspend protocols.
While:
1. on Linux, only 1 instance is supported for DSDT/FACS; and
2. on EFI, the code in osl_get_table() is buggy with special table instances,
causing endless file dump for such tables (reported by Shao Ming in link
#2).
This patch adds DSDT/FACS instance support for Linux/EFI acpidump. Fixed by
Lv Zheng.
Link: https://github.com/acpica/acpica/commit/343fc318
Link: https://bugs.acpica.org/show_bug.cgi?id=1407 [#1]
Link: https://github.com/acpica/acpica/issues/285 [#2]
Reported-by: Shao Ming <smbest163@163.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 01b8f5a2350b9cc329cd8402ac8faec36fc501f5
In order to build ACPICA EFI tools with EDK-II on Windows, 64-bit
multiply/shift supports are also required to be implemented. Otherwise,
MSVC complains:
acpidump.lib(utstrtoul64.obj) : error LNK2001: unresolved external symbol __allmul
acpidump.lib(uthex.obj) : error LNK2001: unresolved external symbol __aullshr
Note:
1. This patch also splits _EDK2_EFI from _GNU_EFI as they might have
different math64 supports.
2. Support of gcc math64 is not included in this patch.
3. Support of EDK2 arch independent math64 is done via linking to base_lib.
This patch fixes this issue. Reported by Shao Ming, fixed by Lv Zheng.
For Linux kernel, this patch is a functional no-op.
Link: https://github.com/acpica/acpica/commit/01b8f5a2
Tested-by: "Shao, Ming" <smbest163@163.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 43ff22215f0fcd8ca80abec5712a07d2cc9a801d
acpi.h inclusion order need to be changed to build EDK-II ports of
acpidump on Windows as va_list is used before it's definition in that
environment. As we only need to ensure order of acenv.h/acenvex.h to
be pre/post ACPICA type definitions, inclusion order is changed to make
MSVC builds happy. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/43ff2221
Signed-off-by: "Shao, Ming" <smbest163@163.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Shao Ming <smbest163@163.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit d586c29a026a6172c1113df4d75fd6d764196e77
Describe 2nd byte of the end_tag resource descriptor.
Link: https://github.com/acpica/acpica/commit/d586c29a
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 8b7fa979ef81469e70f501f582466a265d6f595b
Was emitting an internal namestring without converting it to
the external format.
Link: https://github.com/acpica/acpica/commit/8b7fa979
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 5ad4f0b7bf9e7ba175bd320cf7950f3b38799ff3
ACPI 6.2 adds support for the Software Delegated Exception Interface,
which is described by "Software Delegated Exception Interface (SDEI)"
ARM DEN0054A.
Add the necessary types in the ACPICA header files and support for
compiling/decompiling the table.
Link: https://github.com/acpica/acpica/commit/5ad4f0b7
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit cf27b3c98883d2a15d932016792fcb8272ace96d
The following commit introduces definition of access width to ACPICA.
Commit: 2bece49394872d36bbc5767fd643deac05920c55
Subject: ACPI: SPCR: Use access width to determine mmio usage
Actually the access bit width can be calculated via access width. It
would be better to define a macro calculating bit width rather than
defining fixed values. This patch thus cleans up the definitions to
reduce divergences.
Link: https://github.com/acpica/acpica/commit/cf27b3c9
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
MacBooks and MacBook Pros introduced since 2015 return empty _CRS data
for SPI slaves, causing device initialization to fail. Most of the
information that would normally be conveyed via _CRS is available
through ACPI device properties instead, so take advantage of them.
The meaning and appropriate usage of the device properties was reverse
engineered by Ronald Tschalär and carried over from these commits
authored by him:
https://github.com/cb22/macbook12-spi-driver/commit/9a416d699ef4
https://github.com/cb22/macbook12-spi-driver/commit/0c34936ed9a1
According to Ronald, the device properties have the following meaning:
spiSclkPeriod /* period in ns */
spiWordSize /* in number of bits */
spiBitOrder /* 1 = MSB_FIRST, 0 = LSB_FIRST */
spiSPO /* clock polarity: 0 = low, 1 = high */
spiSPH /* clock phase: 0 = first, 1 = second */
spiCSDelay /* delay between cs and receive on reads in 10 us */
resetA2RUsec /* active-to-receive delay? */
resetRecUsec /* receive delay? */
Reported-by: Leif Liddy <leif.liddy@gmail.com>
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
SPI and I2C slaves are enumerated by their respective parents rather
than the ACPI core. They are recognized by presence of _CRS resources,
which however are missing on Macs. Check for presence of device
properties instead.
Reported-and-tested-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
While the rest of the world has standardized on _DSD as the way to store
device properties in AML (introduced with ACPI 5.1 in 2014), Apple has
been using a custom _DSM to achieve the same for much longer (ever since
they switched from DeviceTree-based PowerPC to Intel in 2005, verified
with MacOS X 10.4.11).
The theory of operation on macOS is as follows: AppleACPIPlatform.kext
invokes mergeEFIproperties() and mergeDSMproperties() for each device to
merge properties conveyed by EFI drivers as well as properties stored in
AML into the I/O Kit registry from which they can be retrieved by
drivers. We've been supporting EFI properties since commit 58c5475aba67
("x86/efi: Retrieve and assign Apple device properties"). The present
commit adds support for _DSM properties, thereby completing our support
for Apple device properties. The _DSM properties are made available
under the primary fwnode, the EFI properties under the secondary fwnode.
So for devices which possess both property types, they can all be
elegantly accessed with the uniform API in <linux/property.h>.
Until recently we had no need to support _DSM properties, they contained
only uninteresting garbage. The situation has changed with MacBooks and
MacBook Pros introduced since 2015: Their keyboard is attached with SPI
instead of USB and the _CRS data which is necessary to initialize the
spi driver only contains valid information if OSPM responds "false" to
_OSI("Darwin"). If OSPM responds "true", _CRS is empty and the spi
driver fails to initialize. The rationale is very simple, Apple only
cares about macOS and Windows: On Windows, _CRS contains valid data,
whereas on macOS it is empty. Instead, macOS gleans the necessary data
from the _DSM properties.
Since Linux deliberately defaults to responding "true" to _OSI("Darwin"),
we need to emulate macOS' behaviour by initializing the spi driver with
data returned by the _DSM.
An out-of-tree driver for the SPI keyboard exists which currently binds
to the ACPI device, invokes the _DSM, parses the returned package and
instantiates an SPI device with the data gleaned from the _DSM:
https://github.com/cb22/macbook12-spi-driver/commit/9a416d699ef4
https://github.com/cb22/macbook12-spi-driver/commit/0c34936ed9a1
By adding support for Apple's _DSM properties in generic ACPI code, the
out-of-tree driver will be able to register as a regular SPI driver,
significantly reducing its amount of code and improving its chances to
be mainlined.
The SPI keyboard will not be the only user of this commit: E.g. on the
MacBook8,1, the UART-attached Bluetooth device likewise returns empty
_CRS data if OSPM returns "true" to _OSI("Darwin").
The _DSM returns a Package whose format unfortunately deviates slightly
from the _DSD spec: The properties are marshalled up in a single Package
as alternating key/value elements, unlike _DSD which stores them as a
Package of 2-element Packages. The present commit therefore converts
the Package to _DSD format and the ACPI core can then treat the data as
if Apple would follow the standard.
Well, except for one small annoyance: The properties returned by the
_DSM only ever have one of two types, Integer or Buffer. The former is
retrievable as usual with device_property_read_u64(), but the latter is
not part of the _DSD spec and it is not possible to retrieve Buffer
properties with the device_property_read_*() functions due to the type
checking performed in drivers/acpi/property.c. It is however possible
to retrieve them with acpi_dev_get_property(). Apple is using the
Buffer type somewhat sloppily to store null-terminated strings but also
integers. The real data type is not distinguishable by the ACPI core
and the onus is on the caller to use the contents of the Buffer in an
appropriate way.
In case Apple moves to _DSD in the future, this commit first checks for
_DSD and falls back to _DSM only if _DSD is not found.
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fabricated devices such as LNXPWRBN lack a handle, causing evaluation
of _CCA and _DSD to always fail with AE_BAD_PARAMETER. While that is
merely a (negligible) waste of processing power, evaluating a _DSM for
them (such as Apple's device properties _DSM which we're about to add)
results in an ugly error:
ACPI: \: failed to evaluate _DSM (0x1001)
Avoid by not evaluating _DSD and the upcoming _DSM for devices without
handle.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We're about to amend ACPI bus scan with DMI checks whether we're running
on a Mac to support Apple device properties in AML. The DMI checks are
performed for every single device, adding overhead for everything x86
that isn't Apple, which is the majority. Rafael and Andy therefore
request to perform the DMI match only once and cache the result.
Outside of ACPI various other Apple DMI checks exist and it seems
reasonable to use the cached value there as well. Rafael, Andy and
Darren suggest performing the DMI check in arch code and making it
available with a header in include/linux/platform_data/x86/.
To this end, add early_platform_quirks() to arch/x86/kernel/quirks.c
to perform the DMI check and invoke it from setup_arch(). Switch over
all existing Apple DMI checks, thereby fixing two deficiencies:
* They are now #defined to false on non-x86 arches and can thus be
optimized away if they're located in cross-arch code.
* Some of them only match "Apple Inc." but not "Apple Computer, Inc.",
which is used by BIOSes released between January 2006 (when the first
x86 Macs started shipping) and January 2007 (when the company name
changed upon introduction of the iPhone).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Suggested-by: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two issues in the ACPI SoC drivers (Intel LPSS and AMD APD),
a crash in the PCC mailbox initialization code and a WDAT watchdog
initialization failure.
Specifics:
- Fix a device ID of Hisilicon Hip07/08 in the ACPI APD (AMD SoC)
driver (Hanjun Guo).
- Fix list corruption (introduced during the 4.11 cycle) in the ACPI
LPSS (Intel SoC) driver (Hans de Goede).
- Fix PCC mailbox handling code crash during initialization when PCCT
is not present and PCC channel 0 is requested (Hoan Tran).
- Fix a WDAT watchdog initialization issue causing platform device
creation to fail due to partially overlapping address ranges in
resources (Ryan Kennedy)"
* tag 'acpi-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: APD: Fix HID for Hisilicon Hip07/08
mailbox: pcc: Fix crash when request PCC channel 0
ACPI / watchdog: Fix init failure with overlapping register regions
ACPI / LPSS: Only call pwm_add_table() for the first PWM controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two cpufreq issues, one introduced recently and one related
to recent changes, fix cpufreq documentation, fix up recently added
code in the Thunderbolt driver and update runtime PM framework
documentation.
Specifics:
- Fix the handling of the scaling_cur_freq cpufreq policy attribute
on x86 systems with the MPERF/APERF registers present to make it
behave more as expected after recent changes (Rafael Wysocki).
- Drop a leftover callback from the intel_pstate driver which also
prevents the cpuinfo_cur_freq cpufreq policy attribute from being
incorrectly exposed when intel_pstate works in the active mode
(Rafael Wysocki).
- Add a missing piece describing the cpuinfo_cur_freq policy
attribute to cpufreq documentation (Rafael Wysocki).
- Fix up a recently added part of the Thunderbolt driver to avoid
aborting system suspends if its mailbox commands time out (Rafael
Wysocki).
- Update device runtime PM framework documentation to reflect the
current behavior of the code (Johan Hovold)"
* tag 'pm-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thunderbolt: icm: Ignore mailbox errors in icm_suspend()
cpufreq: x86: Make scaling_cur_freq behave more as expected
PM / runtime: Document new pm_runtime_set_suspended() constraint
cpufreq: docs: Add missing cpuinfo_cur_freq description
cpufreq: intel_pstate: Drop ->get from intel_pstate structure
|
|
* acpi-soc:
ACPI: APD: Fix HID for Hisilicon Hip07/08
ACPI / LPSS: Only call pwm_add_table() for the first PWM controller
* acpi-wdat:
ACPI / watchdog: Fix init failure with overlapping register regions
* acpi-cppc:
mailbox: pcc: Fix crash when request PCC channel 0
|
|
* pm-core:
PM / runtime: Document new pm_runtime_set_suspended() constraint
* pm-misc:
thunderbolt: icm: Ignore mailbox errors in icm_suspend()
|
|
* pm-cpufreq-x86:
cpufreq: x86: Make scaling_cur_freq behave more as expected
* pm-cpufreq-docs:
cpufreq: docs: Add missing cpuinfo_cur_freq description
* intel_pstate:
cpufreq: intel_pstate: Drop ->get from intel_pstate structure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.13-rc4
Here are some new device ids for v4.13-rc4.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
syzkaller was able to trigger a divide by 0 in TCP stack [1]
Issue here is that keepalive timer needs to be updated to not attempt
to send a probe if the connection setup was deferred using
TCP_FASTOPEN_CONNECT socket option added in linux-4.11
[1]
divide error: 0000 [#1] SMP
CPU: 18 PID: 0 Comm: swapper/18 Not tainted
task: ffff986f62f4b040 ti: ffff986f62fa2000 task.ti: ffff986f62fa2000
RIP: 0010:[<ffffffff8409cc0d>] [<ffffffff8409cc0d>] __tcp_select_window+0x8d/0x160
Call Trace:
<IRQ>
[<ffffffff8409d951>] tcp_transmit_skb+0x11/0x20
[<ffffffff8409da21>] tcp_xmit_probe_skb+0xc1/0xe0
[<ffffffff840a0ee8>] tcp_write_wakeup+0x68/0x160
[<ffffffff840a151b>] tcp_keepalive_timer+0x17b/0x230
[<ffffffff83b3f799>] call_timer_fn+0x39/0xf0
[<ffffffff83b40797>] run_timer_softirq+0x1d7/0x280
[<ffffffff83a04ddb>] __do_softirq+0xcb/0x257
[<ffffffff83ae03ac>] irq_exit+0x9c/0xb0
[<ffffffff83a04c1a>] smp_apic_timer_interrupt+0x6a/0x80
[<ffffffff83a03eaf>] apic_timer_interrupt+0x7f/0x90
<EOI>
[<ffffffff83fed2ea>] ? cpuidle_enter_state+0x13a/0x3b0
[<ffffffff83fed2cd>] ? cpuidle_enter_state+0x11d/0x3b0
Tested:
Following packetdrill no longer crashes the kernel
`echo 0 >/proc/sys/net/ipv4/tcp_timestamps`
// Cache warmup: send a Fast Open cookie request
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 fcntl(3, F_SETFL, O_RDWR|O_NONBLOCK) = 0
+0 setsockopt(3, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0
+0 connect(3, ..., ...) = -1 EINPROGRESS (Operation is now in progress)
+0 > S 0:0(0) <mss 1460,nop,nop,sackOK,nop,wscale 8,FO,nop,nop>
+.01 < S. 123:123(0) ack 1 win 14600 <mss 1460,nop,nop,sackOK,nop,wscale 6,FO abcd1234,nop,nop>
+0 > . 1:1(0) ack 1
+0 close(3) = 0
+0 > F. 1:1(0) ack 1
+0 < F. 1:1(0) ack 2 win 92
+0 > . 2:2(0) ack 2
+0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4
+0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0
+0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0
+0 setsockopt(4, SOL_SOCKET, SO_KEEPALIVE, [1], 4) = 0
+.01 connect(4, ..., ...) = 0
+0 setsockopt(4, SOL_TCP, TCP_KEEPIDLE, [5], 4) = 0
+10 close(4) = 0
`echo 1 >/proc/sys/net/ipv4/tcp_timestamps`
Fixes: 19f6d3f3c842 ("net/tcp-fastopen: Add new API support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Wunderlich says:
====================
Here is a batman-adv bugfix:
- fix TT sync flag inconsistency problems, which can lead to excess packets,
by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.13-rc4
Another fix for isochronous transfers on dwc3. This time around, we're
making sure that we use correct PIDs in all transfer sizes.
MSM PHY driver got a fix for the use of devm_regulator_bulk_get() API
which will avoid kernel crashes.
Renesas DRD driver got 3 fixes: a fix on giveback, a fix for proper
controller programming and the removal of set-but-never-used variable.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
KVM/ARM Fixes for v4.13-rc4
- Yet another race with VM destruction plugged
- A set of small vgic fixes
|
|
Commit 8fba54aebbdf ("fuse: direct-io: don't dirty ITER_BVEC pages") fixes
the ITER_BVEC page deadlock for direct io in fuse by checking in
fuse_direct_io(), whether the page is a bvec page or not, before locking
it. However, this check is missed when the "async_dio" mount option is
enabled. In this case, set_page_dirty_lock() is called from the req->end
callback in request_end(), when the fuse thread is returning from userspace
to respond to the read request. This will cause the same deadlock because
the bvec condition is not checked in this path.
Here is the stack of the deadlocked thread, while returning from userspace:
[13706.656686] INFO: task glusterfs:3006 blocked for more than 120 seconds.
[13706.657808] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables
this message.
[13706.658788] glusterfs D ffffffff816c80f0 0 3006 1
0x00000080
[13706.658797] ffff8800d6713a58 0000000000000086 ffff8800d9ad7000
ffff8800d9ad5400
[13706.658799] ffff88011ffd5cc0 ffff8800d6710008 ffff88011fd176c0
7fffffffffffffff
[13706.658801] 0000000000000002 ffffffff816c80f0 ffff8800d6713a78
ffffffff816c790e
[13706.658803] Call Trace:
[13706.658809] [<ffffffff816c80f0>] ? bit_wait_io_timeout+0x80/0x80
[13706.658811] [<ffffffff816c790e>] schedule+0x3e/0x90
[13706.658813] [<ffffffff816ca7e5>] schedule_timeout+0x1b5/0x210
[13706.658816] [<ffffffff81073ffb>] ? gup_pud_range+0x1db/0x1f0
[13706.658817] [<ffffffff810668fe>] ? kvm_clock_read+0x1e/0x20
[13706.658819] [<ffffffff81066909>] ? kvm_clock_get_cycles+0x9/0x10
[13706.658822] [<ffffffff810f5792>] ? ktime_get+0x52/0xc0
[13706.658824] [<ffffffff816c6f04>] io_schedule_timeout+0xa4/0x110
[13706.658826] [<ffffffff816c8126>] bit_wait_io+0x36/0x50
[13706.658828] [<ffffffff816c7d06>] __wait_on_bit_lock+0x76/0xb0
[13706.658831] [<ffffffffa0545636>] ? lock_request+0x46/0x70 [fuse]
[13706.658834] [<ffffffff8118800a>] __lock_page+0xaa/0xb0
[13706.658836] [<ffffffff810c8500>] ? wake_atomic_t_function+0x40/0x40
[13706.658838] [<ffffffff81194d08>] set_page_dirty_lock+0x58/0x60
[13706.658841] [<ffffffffa054d968>] fuse_release_user_pages+0x58/0x70 [fuse]
[13706.658844] [<ffffffffa0551430>] ? fuse_aio_complete+0x190/0x190 [fuse]
[13706.658847] [<ffffffffa0551459>] fuse_aio_complete_req+0x29/0x90 [fuse]
[13706.658849] [<ffffffffa05471e9>] request_end+0xd9/0x190 [fuse]
[13706.658852] [<ffffffffa0549126>] fuse_dev_do_write+0x336/0x490 [fuse]
[13706.658854] [<ffffffffa054963e>] fuse_dev_write+0x6e/0xa0 [fuse]
[13706.658857] [<ffffffff812a9ef3>] ? security_file_permission+0x23/0x90
[13706.658859] [<ffffffff81205300>] do_iter_readv_writev+0x60/0x90
[13706.658862] [<ffffffffa05495d0>] ? fuse_dev_splice_write+0x350/0x350
[fuse]
[13706.658863] [<ffffffff812062a1>] do_readv_writev+0x171/0x1f0
[13706.658866] [<ffffffff810b3d00>] ? try_to_wake_up+0x210/0x210
[13706.658868] [<ffffffff81206361>] vfs_writev+0x41/0x50
[13706.658870] [<ffffffff81206496>] SyS_writev+0x56/0xf0
[13706.658872] [<ffffffff810257a1>] ? syscall_trace_leave+0xf1/0x160
[13706.658874] [<ffffffff816cbb2e>] system_call_fastpath+0x12/0x71
Fix this by making should_dirty a fuse_io_priv parameter that can be
checked in fuse_aio_complete_req().
Reported-by: Tiger Yang <tiger.yang@oracle.com>
Signed-off-by: Ashish Samant <ashish.samant@oracle.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
There is a small chance that the compiler could generate separate loads
for the dist->propbaser which could be modified from another CPU. As we
want to make sure we atomically update the entire value, and don't race
with other updates, guarantee that the cmpxchg operation compares
against the original value.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
------------[ cut here ]------------
WARNING: CPU: 5 PID: 2288 at arch/x86/kvm/vmx.c:11124 nested_vmx_vmexit+0xd64/0xd70 [kvm_intel]
CPU: 5 PID: 2288 Comm: qemu-system-x86 Not tainted 4.13.0-rc2+ #7
RIP: 0010:nested_vmx_vmexit+0xd64/0xd70 [kvm_intel]
Call Trace:
vmx_check_nested_events+0x131/0x1f0 [kvm_intel]
? vmx_check_nested_events+0x131/0x1f0 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x5dd/0x1be0 [kvm]
? vmx_vcpu_load+0x1be/0x220 [kvm_intel]
? kvm_arch_vcpu_load+0x62/0x230 [kvm]
kvm_vcpu_ioctl+0x340/0x700 [kvm]
? kvm_vcpu_ioctl+0x340/0x700 [kvm]
? __fget+0xfc/0x210
do_vfs_ioctl+0xa4/0x6a0
? __fget+0x11d/0x210
SyS_ioctl+0x79/0x90
do_syscall_64+0x8f/0x750
? trace_hardirqs_on_thunk+0x1a/0x1c
entry_SYSCALL64_slow_path+0x25/0x25
This can be reproduced by booting L1 guest w/ 'noapic' grub parameter, which
means that tells the kernel to not make use of any IOAPICs that may be present
in the system.
Actually external_intr variable in nested_vmx_vmexit() is the req_int_win
variable passed from vcpu_enter_guest() which means that the L0's userspace
requests an irq window. I observed the scenario (!kvm_cpu_has_interrupt(vcpu) &&
L0's userspace reqeusts an irq window) is true, so there is no interrupt which
L1 requires to inject to L2, we should not attempt to emualte "Acknowledge
interrupt on exit" for the irq window requirement in this scenario.
This patch fixes it by not attempt to emulate "Acknowledge interrupt on exit"
if there is no L1 requirement to inject an interrupt to L2.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
[Added code comment to make it obvious that the behavior is not correct.
We should do a userspace exit with open interrupt window instead of the
nested VM exit. This patch still improves the behavior, so it was
accepted as a (temporary) workaround.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
The commit b8b9c974afee ("usb: renesas_usbhs: gadget: disable all eps
when the driver stops") causes the unused-but-set-variable warning.
But, if the usbhsg_ep_disable() will return non-zero value, udc/core.c
doesn't clear the ep->enabled flag. So, this driver should not return
non-zero value, if the pipe is zero because this means the pipe is
already disabled. Otherwise, the ep->enabled flag is never cleared
when the usbhsg_ep_disable() is called by the renesas_usbhs driver first.
Fixes: b8b9c974afee ("usb: renesas_usbhs: gadget: disable all eps when the driver stops")
Fixes: 11432050f070 ("usb: renesas_usbhs: gadget: fix NULL pointer dereference in ep_disable()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
