| Age | Commit message (Collapse) | Author |
|---|
|
Rather than depend on the default pinmuxes, explicitly describe the
pinmux
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230601183151.1000157-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Using a phandle makes it clear which UART we are choosing without needing
to resolve through an alias first.
Especially useful for boards like the TI J721s2-EVM where the alias is
"serial2" but it actually resolves to the 8th UART instance(main_uart8).
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230601184933.358731-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
As the binding for "current-speed" states, this should only be used
when the baud rate of an attached device cannot be detected. This is
the case for our attached on-board USB-to-UART converter used for
early kernel console. For all other unconnected/disabled ports this
can be configured in userspace later, DT is not the place for device
configuration, especially when there are already standard ways to
set serial baud in userspace.
Remove setting baud for all disabled serial ports and move setting
it for the couple enabled ports down into the board files.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230601184933.358731-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add pinmux required to bring out the i2c and gpios on 40 pin RPi
expansion header on AM69 SK board.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-9-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-8-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add wakeup and MCU uart. This allows the device tree usage in
bootloader and firmwares that can configure the same appropriately.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable networking for NFS and basic networking functionality.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: 635fb18ba008 ("arch: arm64: dts: Add support for AM69 Starter Kit")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable wakeup_i2c and use un-used pinmux. While at it, describe the
board detection eeprom present on the board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add wakeup and MCU uart. This allows the device tree usage in
bootloader and firmwares that can configure the same appropriately.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The wkup_pmx register region in j784s4 has multiple non-addressable
regions, hence the existing wkup_pmx region is split as follows to
avoid the non-addressable regions. The pinctrl node offsets are
also corrected as per the newly split wkup_pmx* nodes.
wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
wkup_pmx1 -> 11 pins (WKUP_PADCONFIG 14 - 24)
wkup_pmx2 -> 72 pins (WKUP_PADCONFIG 26 - 97)
wkup_pmx3 -> 1 pin (WKUP_PADCONFIG 100)
Fixes: 4664ebd8346a ("arm64: dts: ti: Add initial support for J784S4 SoC")
Signed-off-by: Thejasvi Konduru <t-konduru@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230503083143.32369-1-t-konduru@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5
SPL attempting to reuse the same definition in the common board
detection logic as it looks for the first i2c instance as the bus on
which to detect the eeprom to understand the board variant involved.
Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0
and potentially space for mcu_i2c instances in the gap for follow on
patches.
Fixes: e20a06aca5c9 ("arm64: dts: ti: Add support for J784S4 EVM board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230602214937.2349545-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
MAIN_PLL0 has a flag set in DM (Device Manager) that removes it's
capability to re-initialise clock frequencies. CPTS and RGMII has
MAIN_PLL3 as their parent which does not have this flag. While RGMII
needs this reinitialisation to default frequency to be able to get
250MHz with its divider, CPTS can not get its required 200MHz with its
divider. Thus, move CPTS clock parent on J721S2 from MAIN_PLL3_HSDIV1 to
MAIN_PLL0_HSDIV6.
(Note: even GTC will be moved from MAIN_PLL3 to MAIN_PLL0 in U-Boot side
for the same reason)
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20230605110443.84568-1-n-francis@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add support for eMMC card connected to main sdhci0 instance.
Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230605174551.160262-1-sabiya.d@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-15-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-14-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-13-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-12-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-11-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-10-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle
and cell arguments easier to catch. Fix the outliers to be consistent
with the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-9-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
array
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle
and cell arguments easier to catch. Fix the outliers to be consistent
with the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-8-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle
and cell arguments easier to catch. Fix the outliers to be consistent
with the rest of the usage.
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
eeprom node
Move the eeprom WP GPIO mux configuration to be part of the eeprom node
instead of the I2C node.
Cc: Robert Nelson <robertcnelson@gmail.com>
Suggested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Move the GPIO mux configuration needed for camera module to work to the
GPIO node instead of the I2C node.
Camera nodes are maintained as overlay files, but the common mux is
always needed to ensure that camera probes fine and ensuring the mux
is configured as part of the GPIO module allows for the multiple
overlay files to be simpler.
Cc: Robert Nelson <robertcnelson@gmail.com>
Suggested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
phandles array
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
When referring to array of phandles, using <> to separate the array
entries is better notation as it makes potential errors with phandle and
cell arguments easier to catch. Fix the outliers to be consistent with
the rest of the usage.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230606182220.3661956-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
There are timer IO pads in the MCU domain, and in the MAIN domain.
These pads can be muxed for the related timers.
The details of the multiplexing can be found in the register
documentation and Technical Reference Manual[1].
These are similar to J721e/J7200, but have different mux capabilities.
[1] http://www.ti.com/lit/zip/spruj52
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230531213215.602395-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
There are 20 general purpose timers on j784s4 that can be used for
things like PWM using pwm-omap-dmtimer driver. There are also
additional ten timers in the MCU domain which are meant for MCU
firmware usage and hence marked reserved by default.
Though the count is similar to J721e/J7200/j721s2, the device IDs
and clocks used in j784s4 are different with the option of certain
clocks having options of additional clock muxes. Since there is very
minimal reuse, it is cleaner to integrate as part of SoC files itself.
The defaults are configured for clocking the timers from system
clock(HFOSC0).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230531213215.602395-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
There are timer IO pads in the MCU domain, and in the MAIN domain. These
pads can be muxed for the related timers.
The details of the multiplexing can be found in the register
documentation and Technical Reference Manual[1].
These are similar to J721e/J7200, but have different mux capabilities.
[1] https://www.ti.com/lit/zip/spruj28
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230531213215.602395-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
There are 20 general purpose timers on j721s2 that can be used for
things like PWM using pwm-omap-dmtimer driver. There are also
additional ten timers in the MCU domain which are meant for MCU
firmware usage and hence marked reserved by default.
Though the count is similar to J721e/J7200, the device IDs and clocks
used in j721s2 are different with the option of certain clocks having
options of additional clock muxes. Since there is very minimal reuse,
it is cleaner to integrate as part of SoC files itself. The defaults
are configured for clocking the timers from system clock(HFOSC0).
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230531213215.602395-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
There are timer IO pads in the MCU domain, and in the MAIN domain. These
pads can be muxed for the related timers.
There are timer IO control registers for input and output. The registers
for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control
the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and
CTRLMMR_MCU_TIMERIO*_CTRL the output.
The multiplexing is documented in Technical Reference Manual[1] under
"Timer IO Muxing Control Registers" and "Timer IO Muxing Control
Registers", and the "Timers Overview" chapters.
We do not expose the cascade_en bit due to the racy usage of
independent 32 bit registers in-line with the timer instantiation in
the device tree. The MCU timer controls are also marked as reserved for
usage by the MCU firmware.
[1] http://www.ti.com/lit/pdf/spruil1
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230531213215.602395-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
There are 20 general purpose timers on j721e that can be used for
things like PWM using pwm-omap-dmtimer driver. There are also
additional ten timers in the MCU domain which are meant for MCU
firmware usage and hence marked reserved by default.
The odd numbered timers have the option of being cascaded to even
timers to create a 64 bit non-atomic counter which is racy in simple
usage, hence the clock muxes are explicitly setup to individual 32 bit
counters driven off system crystal (HFOSC) as default.
These instantiation differs from J7200 and other SoCs with the device
IDs and clocks involved for muxing.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230531213215.602395-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Security Management Subsystem(SMS) has it's own unique secure
proxy as part of Security Accelerator (SA3) module. This is used
for communicating with ROM and for special usecases such as HSM
operations. In addition MCU island has it's own secure proxy for
usecases involving the MCU micro controllers. These are in addition
to the one in the main domain DMSS subsystem that is used for general
purpose communication.
Describe the nodes for use with bootloaders and firmware that require
these communication paths which uses interrupts to corresponding micro
controller interrupt controller. Mark the node as disabled since these
instances do not have interrupts routed to the main processor by
default for a complete description of the node.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230530165900.47502-8-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Security Management Subsystem(SMS) has it's own unique secure
proxy as part of Security Accelerator (SA3) module. This is used
for communicating with ROM and for special usecases such as HSM
operations. In addition MCU island has it's own secure proxy for
usecases involving the MCU micro controllers. These are in addition
to the one in the main domain DMSS subsystem that is used for general
purpose communication.
Describe the nodes for use with bootloaders and firmware that require
these communication paths which uses interrupts to corresponding micro
controller interrupt controller. Mark the node as disabled since these
instances do not have interrupts routed to the main processor by
default for a complete description of the node.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230530165900.47502-7-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
MCU domain has it's own secure proxy for communicating with ROM and
for R5 micro controller firmware operations. This is in addition to
the one in the main domain NAVSS subsystem that is used for general
purpose communication.
Describe the node for use with bootloaders and firmware that require
this communication path which uses interrupts to corresponding micro
controller interrupt controller. Mark the node as disabled since this
instance does not have interrupts routed to the main processor by
default for a complete description of the node.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230530165900.47502-6-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
MCU domain has it's own secure proxy for communicating with ROM and
for R5 micro controller firmware operations. This is in addition to
the one in the main domain NAVSS subsystem that is used for general
purpose communication.
Describe the node for use with bootloaders and firmware that require
this communication path which uses interrupts to corresponding micro
controller interrupt controller. Mark the node as disabled since this
instance does not have interrupts routed to the main processor by
default for a complete description of the node.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230530165900.47502-5-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
MCU domain has it's own secure proxy for communicating with ROM and
for R5 micro controller firmware operations. This is in addition to
the one in the main domain NAVSS subsystem that is used for general
purpose communication.
Describe the node for use with bootloaders and firmware that require
this communication path which uses interrupts to corresponding micro
controller interrupt controller. Mark the node as disabled since this
instance does not have interrupts routed to the main processor by
default for a complete description of the node.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230530165900.47502-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Security Management Subsystem(SMS) has it's own unique secure
proxy as part of Security Accelerator (SA3) module. This is used
for communicating with ROM and for special usecases such as HSM
operations. This is in addition to the one in the main domain DMSS
subsystem that is used for general purpose communication.
Describe the node for use with bootloaders and firmware that require
this communication path which uses interrupts to corresponding micro
controller interrupt controller. Mark the node as disabled since this
instance does not have interrupts routed to the main processor by
default for a complete description of the node.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230530165900.47502-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Security Management Subsystem(SMS) has it's own unique secure
proxy as part of Security Accelerator (SA3) module. This is used
for communicating with ROM and for special usecases such as HSM
operations. This is in addition to the one in the main domain DMSS
subsystem that is used for general purpose communication.
Describe the node for use with bootloaders and firmware that require
this communication path which uses interrupts to corresponding micro
controller interrupt controller. Mark the node as disabled since this
instance does not have interrupts routed to the main processor by
default for a complete description of the node.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
[nm@ti.com: Update commit message, minor updates]
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230530165900.47502-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Just use "rtc" as the nodename to better match with the bindings.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230607132043.3932726-4-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
ti,otap-del-sel has been deprecated in favor of ti,otap-del-sel-legacy.
Drop the duplicate and misleading ti,otap-del-sel property.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230607132043.3932726-3-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
s/mcan/can to stay in sync with bindings conventions.
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20230607132043.3932726-2-nm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Describe OSPI flash partition information through device tree, this
helps to remove passing partition information through the mtdparts
commandline parameter which requires maintaining the partition
information in a string format. AM64 SK and EVM has a S28 64 MiB OSPI
flash with sector size of 256 KiB thus the size of the smallest partition
is chosen as 256 KiB, the partition names and offsets are chosen according
to the corresponding name and offsets in bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513141712.27346-6-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Describe OSPI flash partition information through device tree, this
helps to remove passing partition information through the mtdparts
commandline parameter which requires maintaining the partition
information in a string format. AM654 baseboard has a MT35XU512ABA
64 MiB OSPI flash with sector size of 128 KiB thus the size of the
smallest partition is chosen as 128 KiB, the partition names and
offsets are chosen according to the corresponding name and offsets
in bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513141712.27346-5-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Describe OSPI and Hyperflash partition information through device tree,
this helps to remove passing partition information through the mtdparts
commandline parameter which requires maintaining the partition information
in a string format. J7200 SoM has a S28 64 MiB OSPI flash with sector size
of 256 KiB thus the size of the smallest partition is chosen as 256 KiB,
the SoM also has a 64 MiB Hyperflash present on it, the partition names
and offsets are chosen according to the corresponding name and offsets
in bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513141712.27346-4-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Describe OSPI flash partition information through device tree, this
helps to remove passing partition information through the mtdparts
commandline parameter which requires maintaining the partition
information in a string format. J721E SK has a S28 64 MiB OSPI flash
with sector size of 256 KiB thus the size of the smallest partition is
chosen as 256 KiB, the partition names and offsets are chosen according
to the corresponding name and offsets in bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513141712.27346-3-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Describe OSPI and QSPI flash partition information through device tree,
this helps to remove passing partition information through the mtdparts
commandline parameter which requires maintaining the partition information
in a string format. J721E SoM has a MT35 64 MiB OSPI flash and MT25 64 MiB
QSPI flash both with sector size of 128 KiB thus the size of the smallest
partition is chosen as 128KiB, the partition names and offsets are chosen
according to the corresponding name and offsets in bootloader.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230513141712.27346-2-vaishnav.a@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
J784S4 has S28HS512T OSPI flash connected to OSPI0 and MT25QU512A QSPI
flash connected to OSPI1, enable support for the same. Also describe
the partition information according to the offsets in the bootloader.
Co-developed-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20230504080305.38986-3-a-nandan@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
