| Age | Commit message (Collapse) | Author |
|---|
|
The vblank waits in intel_tv_detect_type() are timing out for some
reason. This is a regression caused removing seemingly useless vblank
waits from the modeset seqeuence in:
commit 56ef52cad5e37fca89638e4bad598a994ecc3d9f
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu May 8 19:23:15 2014 +0300
drm/i915: Kill vblank waits after pipe enable on gmch platforms
So it turns out they weren't all entirely useless. Apparently the pipe
has to go through one full frame before we enable the TV port. Add a
vblank wait to intel_enable_tv() to make sure that happens.
Another approach was attempted by placing the vblank wait just after
enabling the port. The theory behind that attempt was that we need to
let the port stay enabled for one full frame before disabling it again
during load detection. But that didn't work, and we definitely must
have the vblank wait before enabling the port.
Cc: stable@vger.kernel.org
Cc: Alan Bartlett <ajb@elrepo.org>
Tested-by: Alan Bartlett <ajb@elrepo.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79311
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If a memory block is not aligned to PAGE_SIZE, its base address must be
rounded up, not down, and its size must be reduced.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Simply swap of_alias and of_chosen initialization so
that of_alias ends up read first. This must be done
because it is accessed couple of lines below when
trying to initialize the of_stdout using the alias
based legacy method.
[Fixes a752ee5 - tty: Update hypervisor tty drivers to
use core stdout parsing code]
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
[glikely: Don't move the 'if (!of_aliases)' test]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
This patch add a document that explains how the selftest test data is
dynamically attached into the live device tree irrespective of the
machine's architecture.
Signed-off-by: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
This patch is to the fix the recent runtime bug in kernel reported by
<fengguang.wu@intel.com>. The bug was exposed by commit b951f9dc,
"Enabling OF selftest to run without machine's devicetree" and is
exposed when CONFIG_OF_SELFTEST is enabled and CONFIG_SYSFS is
disabled.
Mail Subject: [OF test] BUG: unable to handle kernel NULL pointer
dereference at 00000038
Tested on x86 and arm architecture
Signed-off-by: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
The comments above of_console_check() say that it will return TRUE if it
registers a preferred console, but add_preferred_console() uses a
0-equals-success convention, so this leaves of_console_check() with an
inconsistent policy for its return values.
Fortunately, nobody was actually checking the return value of
of_console_check(), so this isn't significant at the moment.
But let's match the comments, so we're doing what we say.
Fixes: 3482f2c52b77 ('of: Create of_console_check() for selecting a console specified in /chosen')
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Running igt, I was encountering the invalid TLB bug on my 845g, despite
that it was using the CS workaround. Examining the w/a buffer in the
error state, showed that the copy from the user batch into the
workaround itself was suffering from the invalid TLB bug (the first
cacheline was broken with the first two words reversed). Time to try a
fresh approach. This extends the workaround to write into each page of
our scratch buffer in order to overflow the TLB and evict the invalid
entries. This could be refined to only do so after we update the GTT,
but for simplicity, we do it before each batch.
I suspect this supersedes our current workaround, but for safety keep
doing both.
v2: The magic number shall be 2.
This doesn't conclusively prove that it is the mythical TLB bug we've
been trying to workaround for so long, that it requires touching a number
of pages to prevent the corruption indicates to me that it is TLB
related, but the corruption (the reversed cacheline) is more subtle than
a TLB bug, where we would expect it to read the wrong page entirely.
Oh well, it prevents a reliable hang for me and so probably for others
as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The value64 parameter is an u64 point that used to transfer the value
for write to CMOS, or used to return the value that's read from CMOS.
The value64 is an u64 point, so don't need get address again. It causes
acpi_cmos_rtc_space_handler always return 0 to reader and didn't write
expected value to CMOS.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The macro "REGMAP_ALLOW_WRITE_DEBUGFS" can be used to enable write
support on the registers file in the debugfs. The mode of the file is
fixed to 0400 so it is not possible to write the file ever.
This patch fixes the mode by setting it to the correct value depending
on the macro.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In
https://bugzilla.kernel.org/show_bug.cgi?id=84031,
the submitter said that disabling power saving helped,
do just that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
smps_mode is used uninitialized in a debug statement in AP
mode, so always initialize it.
While at it, fix a typo.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The latter is meant for software implementation of power
save and is not per-virtual interface. Since our driver
supports multiple virtual interfaces, we need to use
vif->bss_conf.dtim_period.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Using the LQ table which is initially set according to
the rssi could lead to EAPOLs being sent in high legacy
rates like 54mbps.
It's better to avoid sending EAPOLs in high rates as it reduces
the chances of a successful 4-Way handshake.
Avoid this and treat them like other mgmt frames which would
initially get sent at the basic rate.
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When mac80211 requests multiple BSS config changes, as for example
while associating, we ignore power management and QoS changes and
only apply them later. Fix that by removing the "else" and making
the conditions independent.
Also move it after (potential) beacon filter enablement to have
that already enabled when going into power management code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The chip is able to transmit up to 22dBm, so set
the constant appropriately.
CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This code was broken on big endian systems. Sparse didn't
catch the bug since the firmware command was not tagged as
little endian.
Fix the bug for big endian systems and tag the field in the
firmware command to prevent such issues in the future.
Cc: stable@vger.kernel.org [3.14+]
Fixes: 1f3b0ff8ec ("iwlwifi: mvm: Add Smart FIFO support")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
In commit cad3f08c (iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when
forced_assoc_off is set) the code to set the MAC_FILTER_IN_BEACON flag
was accidentally moved to the main block of the if statement, while it
should be in the else block instead. Move it to the right place.
Fixes: cad3f08c23de ("iwlwifi: mvm: enable MAC_FILTER_IN_BEACON when forced_assoc_off is set")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The variable 'u32 mode' exists twice, the latter shadowing
the former - remove the latter since there's no need for
two variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
A bunch of warnings fire on some ->irq_postinstall hooks since those
can enable interrupts (e.g. rps interrupts). And then our ordering
self-checks fire and complain.
To fix that set the tracking boolen before enabling the irqs with
drm_irq_install. Quoting the discussion with Jesse why that's safe:
On Tue, Aug 26, 2014 at 11:18 PM, Jesse Barnes <jbarnes@virtuousgeek.org> wrote:
> Yes, it might work, but if you look through the history, we set this
> field carefully; first to true in the irq_init code, then to false only
> after the irq_install completes. So I think your fragility arguments
> apply to this change too.
Well we've done it in 4 commits or so, but currently we have:
- Set irqs_disabled to true early in driver load to make sure checks
that. That's done in irq_init, which is totally not the function that
enables interrupts, only the function that initializes all the vtables
and similar things. We actually have a fairly sane naming scheme
nowadays (not fully consistent ofc): _init is sw setup,
_enable/_hw_init is the actual hw setup. That is done in
95f25beddba2ec9510b249740bacc11eca70cf75
- Set irqs_disabled to false right after the irqs are actually
enabled. This is done in ed2e6df18935beb3d63613c50103bf9757b2aa85
So my change should only move the flag change over the ->preinstall
and ->postinstall hooks. I've done a little audit and didn't spot
anything amiss. Furthermore the runtime pm setup already clears
irqs_disabled _before_ calling these two hooks.
This regression has been introduced in
commit ed2e6df18935beb3d63613c50103bf9757b2aa85
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Jun 20 09:39:36 2014 -0700
drm/i915: clear pm._irqs_disabled field after installing IRQs
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # gm45, ilk
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
In
commit 1f83fee08d625f8d0130f9fe5ef7b17c2e022f3c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Nov 15 17:17:22 2012 +0100
drm/i915: clear up wedged transitions
I've accidentally inverted the EIO/wedged handling in the fault
handler: We want to return the EIO as a SIGBUS only if it's not
because of the gpu having died, to prevent userspace from unduly
dying.
In my defence the comment right above is completely misleading, so fix
both.
v2: Drop the WARN_ON, it's not actually a bug to e.g. receive an -EIO
when swap-in fails.
v3: Don't remove too much ... oops.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
During release of the GEM object we hold the struct_mutex. As the
object may be holding onto the last reference for the task->mm,
calling mmput() may trigger exit_mmap() which close the vma
which will call drm_gem_vm_close() and attempt to reacquire
the struct_mutex. In order to avoid that recursion, we have
to defer the mmput() until after we drop the struct_mutex,
i.e. we need to schedule a worker to do the clean up. A further issue
spotted by Tvrtko was caused when we took a GTT mmapping of a userptr
buffer object. In that case, we would never call mmput as the object
would be cyclically referenced by the GTT mmapping and not freed upon
process exit - keeping the entire process mm alive after the process
task was reaped. The fix employed is to replace the mm_users/mmput()
reference handling to mm_count/mmdrop() for the shared i915_mm_struct.
INFO: task test_surfaces:1632 blocked for more than 120 seconds.
Tainted: GF O 3.14.5+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
test_surfaces D 0000000000000000 0 1632 1590 0x00000082
ffff88014914baa8 0000000000000046 0000000000000000 ffff88014914a010
0000000000012c40 0000000000012c40 ffff8800a0058210 ffff88014784b010
ffff88014914a010 ffff880037b1c820 ffff8800a0058210 ffff880037b1c824
Call Trace:
[<ffffffff81582499>] schedule+0x29/0x70
[<ffffffff815825fe>] schedule_preempt_disabled+0xe/0x10
[<ffffffff81583b93>] __mutex_lock_slowpath+0x183/0x220
[<ffffffff81583c53>] mutex_lock+0x23/0x40
[<ffffffffa005c2a3>] drm_gem_vm_close+0x33/0x70 [drm]
[<ffffffff8115a483>] remove_vma+0x33/0x70
[<ffffffff8115a5dc>] exit_mmap+0x11c/0x170
[<ffffffff8104d6eb>] mmput+0x6b/0x100
[<ffffffffa00f44b9>] i915_gem_userptr_release+0x89/0xc0 [i915]
[<ffffffffa00e6706>] i915_gem_free_object+0x126/0x250 [i915]
[<ffffffffa005c06a>] drm_gem_object_free+0x2a/0x40 [drm]
[<ffffffffa005cc32>] drm_gem_object_handle_unreference_unlocked+0xe2/0x120 [drm]
[<ffffffffa005ccd4>] drm_gem_object_release_handle+0x64/0x90 [drm]
[<ffffffff8127ffeb>] idr_for_each+0xab/0x100
[<ffffffffa005cc70>] ? drm_gem_object_handle_unreference_unlocked+0x120/0x120 [drm]
[<ffffffff81583c46>] ? mutex_lock+0x16/0x40
[<ffffffffa005c354>] drm_gem_release+0x24/0x40 [drm]
[<ffffffffa005b82b>] drm_release+0x3fb/0x480 [drm]
[<ffffffff8118d482>] __fput+0xb2/0x260
[<ffffffff8118d6de>] ____fput+0xe/0x10
[<ffffffff8106f27f>] task_work_run+0x8f/0xf0
[<ffffffff81052228>] do_exit+0x1a8/0x480
[<ffffffff81052551>] do_group_exit+0x51/0xc0
[<ffffffff810525d7>] SyS_exit_group+0x17/0x20
[<ffffffff8158e092>] system_call_fastpath+0x16/0x1b
v2: Incorporate feedback from Tvrtko and remove the unnessary mm
referencing when creating the i915_mm_struct and improve some of the
function names and comments.
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Test-case: igt/gem_userptr_blits/process-exit*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: "Gong, Zhipeng" <zhipeng.gong@intel.com>
Cc: Jacek Danecki <jacek.danecki@intel.com>
Cc: "Ursulin, Tvrtko" <tvrtko.ursulin@intel.com>
Reviewed-by: "Ursulin, Tvrtko" <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org # hold off until 3.17 ships for additional testing
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"This pull request includes Alban's patch to disallow '\n' in cgroup
names.
Two other patches from Li to fix a possible oops when cgroup
destruction races against other file operations and one from Vivek to
fix a unified hierarchy devel behavior"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: check cgroup liveliness before unbreaking kernfs
cgroup: delay the clearing of cgrp->kn->priv
cgroup: Display legacy cgroup files on default hierarchy
cgroup: reject cgroup names with '\n'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fixes from Tejun Heo:
"One patch to fix a failure path in the alloc path. The bug is
dangerous but probably not too likely to actually trigger in the wild
given that there hasn't been any report yet.
The other two are low impact fixes"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: free percpu allocation info for uniprocessor system
percpu: perform tlb flush after pcpu_map_pages() failure
percpu: fix pcpu_alloc_pages() failure path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Two patches are to add PCI IDs for ICH9 and all others are device
specific fixes. Nothing too interesting"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_xgene: Fix the link down in first attempt for the APM X-Gene SoC AHCI SATA host controller driver.
ahci_xgene: Skip the PHY and clock initialization if already configured by the firmware.
ahci: add pcid for Marvel 0x9182 controller
ata: Disabling the async PM for JMicron chip 363/361
ata_piix: Add Device IDs for Intel 9 Series PCH
ahci: Add Device IDs for Intel 9 Series PCH
ata: ahci_tegra: Read calibration fuse
|
|
Pull networking fixes from David Miller:
1) Fix skb leak in mac802154, from Martin Townsend
2) Use select not depends on NF_NAT for NFT_NAT, from Pablo Neira
Ayuso
3) Fix union initializer bogosity in vxlan, from Gerhard Stenzel
4) Fix RX checksum configuration in stmmac driver, from Giuseppe
CAVALLARO
5) Fix TSO with non-accelerated VLANs in e1000, e1000e, bna, ehea,
i40e, i40evf, mvneta, and qlge, from Vlad Yasevich
6) Fix capability checks in phy_init_eee(), from Giuseppe CAVALLARO
7) Try high order allocations more sanely for SKBs, specifically if a
high order allocation fails, fall back directly to zero order pages
rather than iterating down one order at a time. From Eric Dumazet
8) Fix a memory leak in openvswitch, from Li RongQing
9) amd-xgbe initializes wrong spinlock, from Thomas Lendacky
10) RTNL locking was busted in setsockopt for anycast and multicast, fix
from Sabrina Dubroca
11) Fix peer address refcount leak in ipv6, from Nicolas Dichtel
12) DocBook typo fixes, from Masanari Iida
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
ipv6: restore the behavior of ipv6_sock_ac_drop()
amd-xgbe: Enable interrupts for all management counters
amd-xgbe: Treat certain counter registers as 64 bit
greth: moved TX ring cleaning to NAPI rx poll func
cnic : Cleanup CONFIG_IPV6 & VLAN check
net: treewide: Fix typo found in DocBook/networking.xml
bnx2x: Fix link problems for 1G SFP RJ45 module
3c59x: avoid panic in boomerang_start_xmit when finding page address:
netfilter: add explicit Kconfig for NETFILTER_XT_NAT
ipv6: use addrconf_get_prefix_route() to remove peer addr
ipv6: fix a refcnt leak with peer addr
net-timestamp: only report sw timestamp if reporting bit is set
drivers/net/fddi/skfp/h/skfbi.h: Remove useless PCI_BASE_2ND macros
l2tp: fix race while getting PMTU on PPP pseudo-wire
ipv6: fix rtnl locking in setsockopt for anycast and multicast
VMXNET3: Check for map error in vmxnet3_set_mc
openvswitch: distinguish between the dropped and consumed skb
amd-xgbe: Fix initialization of the wrong spin lock
openvswitch: fix a memory leak
netfilter: fix missing dependencies in NETFILTER_XT_TARGET_LOG
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-05
Please pull this batch of fixes intended for the 3.17 stream...
For the mac80211 bits, Johannes says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
For the iwlwifi bits, Emmanuel says:
"I revert a patch that disabled CTS to self in dvm because users
reported issues. The revert is CCed to stable since the offending
patch was sent to stable too. I also bump the firmware API versions
since a new firmware is coming up. On top of that, Marcel fixes a
bug I introduced while fixing a bug in our Kconfig file."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible that the interface is already gone after joining
the list of anycast on this interface as we don't hold a refcount
for the device, in this case we are safe to ignore the error.
What's more important, for API compatibility we should not
change this behavior for applications even if it were correct.
Fixes: commit a9ed4a2986e13011 ("ipv6: fix rtnl locking in setsockopt for anycast and multicast")
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
new link for - How to piss off a Linux kernel subsystem maintainer
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The NFS/RDMA Kconfig symbol was split into separate options for client
and server in commit 2e8c12e1b765 ("xprtrdma: add separate Kconfig
options for NFSoRDMA client and server support").
Update the documentation to reflect this split.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "J. Bruce Fields" <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
hpfall.c was renamed to freefall.c in 3.16, but this file still refer to
hpfall.c instead of freefall.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The example code provided with the i2c device interface documentation
won't compile since it uses the reserved word "register" to name a
variable.
The compiler fails with this error message:
error: expected identifier or '(' before '=' token
__u8 register = 0x20; /* Device register to access */
^
Rename the variable "register" to simply "reg" in the example code.
Another couple of typos has been fixed as well.
[Change "! =" to "!=".]
Signed-off-by: Jose Alarcon Roldan <jose.alarcon.roldan@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Despite the fact that these functions have been around for years, they
are little used (only 15 uses in 13 files at the preseht time) even
though many other files use work-arounds to achieve the same result.
By documenting them, hopefully they will become more widely used.
Signed-off-by: Rob Jones <rob.jones@codethink.co.uk>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These changes fix the argument to the kcalloc
@n: number of elements.
@size: element size.
@flags: the type of memory to allocate (see kmalloc).
void *kcalloc(size_t n, size_t size, gfp_t flags)
Fixes: 3c5445ce3a0c (cpufreq: OPP: Avoid sleeping while atomic)
Signed-off-by: Anand Moon <moon.linux@yahoo.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the previous makefile 2 modules were generated for CONFIG_NFC_ST21NFCA
(st21nfca.ko and st21nfca_dep.ko). Merge both of them into st21nfca_hci.ko
and fix a potential depmod dependency cycle, similar to the one we saw
on st21nfcb:
depmod: WARNING: found 6 modules in dependency cycles!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/st21nfcb.ko
in dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/ndlc.ko
in dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/rfkill/rfkill.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nfc.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nci/nci.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/lib/crc-ccitt.ko in
dependency cycle!
./scripts/depmod.sh: line 57: 23387 Segmentation fault (core
dumped) "$DEPMOD" "$@" "$KERNELRELEASE" $SYMBOL_PREFIX
make: *** [_modinst_post] Error 139
Reported-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This fix issue reported here:
https://lists.01.org/pipermail/linux-nfc/2014-September/002871.html
depmod: WARNING: found 6 modules in dependency cycles!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/st21nfcb.ko
in dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/drivers/nfc/st21nfcb/ndlc.ko
in dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/rfkill/rfkill.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nfc.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/net/nfc/nci/nci.ko in
dependency cycle!
depmod: WARNING:
/lib/modules/3.17.0-rc3-00002-g7505cea/kernel/lib/crc-ccitt.ko in
dependency cycle!
./scripts/depmod.sh: line 57: 23387 Segmentation fault (core
dumped) "$DEPMOD" "$@" "$KERNELRELEASE" $SYMBOL_PREFIX
make: *** [_modinst_post] Error 139
Reported-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI sysfs, ACPI video, suspend test),
ACPI cpuidle deadlock fix, missing runtime validation of ACPI _DSD
output, a fix and a new CPU ID for the RAPL driver, new blacklist
entry for the ACPI EC driver and a couple of trivial cleanups
(intel_pstate and generic PM domains).
Specifics:
- Fix for recently broken test_suspend= command line argument (Rafael
Wysocki).
- Fixes for regressions related to the ACPI video driver caused by
switching the default to native backlight handling in 3.16 from
Hans de Goede.
- Fix for a sysfs attribute of ACPI device objects that returns stale
values sometimes due to the fact that they are cached instead of
executing the appropriate method (_SUN) every time (broken in
3.14). From Yasuaki Ishimatsu.
- Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock in the
ACPI processor driver from Jiri Kosina.
- Runtime output validation for the ACPI _DSD device configuration
object missing from the support for it that has been introduced
recently. From Mika Westerberg.
- Fix for an unuseful and misleading RAPL (Running Average Power
Limit) domain detection message in the RAPL driver from Jacob Pan.
- New Intel Haswell CPU ID for the RAPL driver from Jason Baron.
- New Clevo W350etq blacklist entry for the ACPI EC driver from Lan
Tianyu.
- Cleanup for the intel_pstate driver and the core generic PM domains
code from Gabriele Mazzotta and Geert Uytterhoeven"
* tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
cpufreq: intel_pstate: Remove unneeded variable
powercap / RAPL: change domain detection message
powercap / RAPL: add support for CPU model 0x3f
PM / domains: Make generic_pm_domain.name const
PM / sleep: Fix test_suspend= command line option
ACPI / EC: Add msi quirk for Clevo W350etq
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull filesystem fixes from Al Viro:
"Several bugfixes (all of them -stable fodder).
Alexey's one deals with double mutex_lock() in UFS (apparently, nobody
has tried to test "ufs: sb mutex merge + mutex_destroy" on something
like file creation/removal on ufs). Mine deal with two kinds of
umount bugs, in umount propagation and in handling of automounted
submounts, both resulting in bogus transient EBUSY from umount"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: fix deadlocks introduced by sb mutex merge
fix EBUSY on umount() from MNT_SHRINKABLE
get rid of propagate_umount() mistakenly treating slaves as busy.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU fix from Ingo Molnar:
"A boot hang fix for the offloaded callback RCU model (RCU_NOCB_CPU=y
&& (TREE_CPU=y || TREE_PREEMPT_RC)) in certain bootup scenarios"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make nocb leader kthreads process pending callbacks after spawning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Three fixlets from the timer departement:
- Update the timekeeper before updating vsyscall and pvclock. This
fixes the kvm-clock regression reported by Chris and Paolo.
- Use the proper irq work interface from NMI. This fixes the
regression reported by Catalin and Dave.
- Clarify the compat_nanosleep error handling mechanism to avoid
future confusion"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Update timekeeper before updating vsyscall and pvclock
compat: nanosleep: Clarify error handling
nohz: Restore NMI safe local irq work for local nohz kick
|
|
Commit 0244756edc4b ("ufs: sb mutex merge + mutex_destroy") introduces
deadlocks in ufs_new_inode() and ufs_free_inode().
Most callers of that functions acqure the mutex by themselves and
ufs_{new,free}_inode() do that via lock_ufs(),
i.e we have an unavoidable double lock.
The patch proposes to resolve the issue by making sure that
ufs_{new,free}_inode() are not called with the mutex held.
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull kvm fixes from Paolo Bonzini:
"A smattering of bug fixes across most architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
powerpc/kvm/cma: Fix panic introduces by signed shift operation
KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
KVM: s390/mm: Fix storage key corruption during swapping
arm/arm64: KVM: Complete WFI/WFE instructions
ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
KVM: s390/mm: try a cow on read only pages for key ops
KVM: s390: Fix user triggerable bug in dead code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"Another round of fixes from arm-soc land, which are mostly DT fixes
for:
- OMAP: handful of DT fixes devices on newly supported hardware
- davinci: fix 2nd EDMA channel
- ux500: extend previous pinctrl fix to another board
- at91: clock registration fixes, compatibility string precision
And one more fix for event cleanup in drivers/bus/arm-ccn"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Move event cleanup routine
ARM: at91/dt: rm9200: fix usb clock definition
ARM: at91: rm9200: fix clock registration
ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
ARM: dts: dra7-evm: Add vtt regulator support
ARM: dts: dra7-evm: Fix spi1 mux documentation
ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am4372: fix USB regs size
ARM: dts: am437x-gp: switch i2c0 to 100KHz
ARM: dts: dra7-evm: Fix 8th NAND partition's name
ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
ARM: ux500: disable msp2 node on Snowball
ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
ARM: dts: set 'ti,set-rate-parent' for dpll4_m5x2 clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"The fixes all address recently discovered data corruption issues.
The original Direct IO issue was discovered by Chris Mason @ Facebook
on a production workload which mixed buffered reads with direct reads
and writes IO to the same file. The fix for that exposed other issues
with page invalidation (exposed by millions of fsx operations) failing
due to dirty buffers beyond EOF.
Finally, the collapse_range code could also cause problems due to
racing writeback changing the extent map while it was being shifted
around. The commits for that problem are simple mitigation fixes that
prevent the problem from occuring. A more robust fix for 3.18 that
addresses the underlying problem is currently being worked on by
Brian.
Summary of fixes:
- a direct IO read/buffered read data corruption
- the associated fallout from the DIO data corruption fix
- collapse range bugs that are potential data corruption issues"
* tag 'xfs-for-linus-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: trim eofblocks before collapse range
xfs: xfs_file_collapse_range is delalloc challenged
xfs: don't log inode unless extent shift makes extent modifications
xfs: use ranged writeback and invalidation for direct IO
xfs: don't zero partial page cache pages during O_DIRECT writes
xfs: don't zero partial page cache pages during O_DIRECT writes
xfs: don't dirty buffers beyond EOF
|
|
Pull mtd fixes from Brian Norris:
"Two trivial MTD updates for 3.17-rc4:
- a tiny comment tweak, to kill a bunch of DocBook warnings added
during the merge window
- a small fixup to the OTP routines' error handling"
* tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd:
mtd: nand: fix DocBook warnings on nand_sdr_timings doc
mtd: cfi_cmdset_0002: check return code for get_chip()
|
|
I moved from ST Microelectronics and the email-id no longer
exists. Update email-id to personal one,
Signed-off-by: Rajeev Kumar <rajeevkumar.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The update_walltime() code works on the shadow timekeeper to make the
seqcount protected region as short as possible. But that update to the
shadow timekeeper does not update all timekeeper fields because it's
sufficient to do that once before it becomes life. One of these fields
is tkr.base_mono. That stays stale in the shadow timekeeper unless an
operation happens which copies the real timekeeper to the shadow.
The update function is called after the update calls to vsyscall and
pvclock. While not correct, it did not cause any problems because none
of the invoked update functions used base_mono.
commit cbcf2dd3b3d4 (x86: kvm: Make kvm_get_time_and_clockread()
nanoseconds based) changed that in the kvm pvclock update function, so
the stale mono_base value got used and caused kvm-clock to malfunction.
Put the update where it belongs and fix the issue.
Reported-by: Chris J Arges <chris.j.arges@canonical.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1409050000570.3333@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The error handling in compat_sys_nanosleep() is correct, but
completely non obvious. Document it and restrict it to the
-ERESTART_RESTARTBLOCK return value for clarity.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver fixes 2014-09-05
The following series of patches includes fixes to the driver.
- Proper access to 64 bit management counter registers
- Enable all management counter registers to generate an interrupt when
the counter threshold is reached
This patch series is based on net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.
Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
