| Age | Commit message (Collapse) | Author |
|---|
|
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, pass the link mode bit in use.
In Spectrum-1, simply pass the bit that is set to '1' from PTYS register.
In Spectrum-2, pass the first link mode bit in the mask of the used
link mode.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when auto negotiation is set to off, the user can force a
specific speed or both speed and duplex. The user cannot influence the
number of lanes that will be forced.
Add support for setting speed along with lanes so one would be able
to choose how many lanes will be forced.
When lanes parameter is passed from user space, choose the link mode
that its actual width equals to it.
Otherwise, the default link mode will be the one that supports the width
of the port.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when a speed can be supported by different number of lanes,
the supported link modes bitmask contains only link modes with a single
number of lanes.
This was done in order to prevent auto negotiation on number of
lanes after 50G-1-lane and 100G-2-lanes link modes were introduced.
For example, if a port's max width is 4, only link modes with 4 lanes
will be presented as supported by that port, so 100G is always achieved by
4 lanes of 25G.
After the previous patches that allow selection of the number of lanes,
auto negotiation on number of lanes becomes practical.
Remove that filtering of the maximum number of lanes supported link modes,
so indeed all the supported and advertised link modes will be shown.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, ethtool does not expose how many lanes are used when the
link is up.
After adding a possibility to advertise or force a specific number of
lanes, the lanes in use value can be either the maximum width of the port
or below.
Extend ethtool to expose the number of lanes currently in use for
drivers that support it.
For example:
$ ethtool -s swp1 speed 100000 lanes 4
$ ethtool -s swp2 speed 100000 lanes 4
$ ip link set swp1 up
$ ip link set swp2 up
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE Backplane ]
Supported link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
50000baseKR/Full
50000baseSR/Full
50000baseCR/Full
50000baseLR_ER_FR/Full
50000baseDR/Full
100000baseKR2/Full
100000baseSR2/Full
100000baseCR2/Full
100000baseLR2_ER2_FR2/Full
100000baseDR2/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseT/Full
10000baseT/Full
1000baseKX/Full
1000baseKX/Full
10000baseKR/Full
10000baseR_FEC
40000baseKR4/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseKR/Full
25000baseSR/Full
50000baseCR2/Full
50000baseKR2/Full
100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
50000baseSR2/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
200000baseKR4/Full
200000baseSR4/Full
200000baseLR4_ER4_FR4/Full
200000baseDR4/Full
200000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Advertised link modes: 100000baseKR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 100000Mb/s
Lanes: 4
Duplex: Full
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, get the link mode bit in use, and derive each of the parameters
from it in ethtool.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, when auto negotiation is on, the user can advertise all the
linkmodes which correspond to a specific speed, but does not have a
similar selector for the number of lanes. This is significant when a
specific speed can be achieved using different number of lanes. For
example, 2x50 or 4x25.
Add 'ETHTOOL_A_LINKMODES_LANES' attribute and expand 'struct
ethtool_link_settings' with lanes field in order to implement a new
lanes-selector that will enable the user to advertise a specific number
of lanes as well.
When auto negotiation is off, lanes parameter can be forced only if the
driver supports it. Add a capability bit in 'struct ethtool_ops' that
allows ethtool know if the driver can handle the lanes parameter when
auto negotiation is off, so if it does not, an error message will be
returned when trying to set lanes.
Example:
$ ethtool -s swp1 lanes 4
$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
25000baseCR/Full
25000baseSR/Full
50000baseCR2/Full
100000baseSR4/Full
100000baseCR4/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Link detected: no
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a new function for input validations to be called before
rtnl_lock() and move the master slave validation to that function.
This would be a cleanup for next patch that would add another validation
to the new function.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
* drm/bridge/lontium-lt9611uxc: EDID fixes; Don't handle hotplug
events in IRQ handler
* drm/ttm: Use _GFP_NOWARN for huge pages
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YBlHU4sc/5GHpXpg@linux-uq9g
|
|
The bridge emits VLAN filtering events and quite a few others via
switchdev with orig_dev = br->dev. After the blamed commit, these events
started getting ignored.
The point of the patch was to not offload switchdev objects for ports
that didn't go through dsa_port_bridge_join, because the configuration
is unsupported:
- ports that offload a bonding/team interface go through
dsa_port_bridge_join when that bonding/team interface is later bridged
with another switch port or LAG
- ports that don't offload LAG don't get notified of the bridge that is
on top of that LAG.
Sadly, a check is missing, which is that the orig_dev is equal to the
bridge device. This check is compatible with the original intention,
because ports that don't offload bridging because they use a software
LAG don't have dp->bridge_dev set.
On a semi-related note, we should not offload switchdev objects or
populate dp->bridge_dev if the driver doesn't implement .port_bridge_join
either. However there is no regression associated with that, so it can
be done separately.
Fixes: 5696c8aedfcc ("net: dsa: Don't offload port attributes on standalone ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20210202233109.1591466-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sebastian Andrzej Siewior says:
====================
chelsio: cxgb: Use threaded interrupts for deferred work
Patch #2 fixes an issue in which del_timer_sync() and tasklet_kill() is
invoked from the interrupt handler. This is probably a rare error case
since it disables interrupts / the card in that case.
Patch #1 converts a worker to use a threaded interrupt which is then
also used in patch #2 instead adding another worker for this task (and
flush_work() to synchronise vs rmmod).
====================
Link: https://lore.kernel.org/r/20210202170104.1909200-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
t1_fatal_err() is invoked from the interrupt handler. The bad part is
that it invokes (via t1_sge_stop()) del_timer_sync() and tasklet_kill().
Both functions must not be called from an interrupt because it is
possible that it will wait for the completion of the timer/tasklet it
just interrupted.
In case of a fatal error, use t1_interrupts_disable() to disable all
interrupt sources and then wake the interrupt thread with
F_PL_INTR_SGE_ERR as pending flag. The threaded-interrupt will stop the
card via t1_sge_stop() and not re-enable the interrupts again.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The external interrupt (F_PL_INTR_EXT) needs to be handled in a process
context and this is accomplished by utilizing a workqueue.
The process context can also be provided by a threaded interrupt instead
of a workqueue. The threaded interrupt can be used later for other
interrupt related processing which require non-atomic context without
using yet another workqueue. free_irq() also ensures that the thread is
done which is currently missing (the worker could continue after the
module has been removed).
Save pending flags in pending_thread_intr. Use the same mechanism
to disable F_PL_INTR_EXT as interrupt source like it is used before the
worker is scheduled. Enable the interrupt again once
t1_elmer0_ext_intr_handler() is done.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Srujana Challa says:
====================
Support for OcteonTX2 98xx CPT block.
OcteonTX2 series of silicons have multiple variants, the
98xx variant has two crypto (CPT) blocks to double the crypto
performance. This patchset adds support for new CPT block(CPT1).
====================
Link: https://lore.kernel.org/r/20210202152709.20450-1-schalla@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleans up all resources
attached to that VF. This patch adds support to handle
CPT FLR.
Signed-off-by: Narayana Prasad Raju Atherya <pathreya@marvell.com>
Signed-off-by: Suheil Chandran <schandran@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adds support to display block CPT1 stats at
"/sys/kernel/debug/octeontx2/cpt1".
Signed-off-by: Mahipal Challa <mchalla@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch changes CPT mailbox message format to
support new block CPT1 in 98xx silicon.
cpt_rd_wr_reg ->
Modify cpt_rd_wr_reg mailbox and its handler to
accommodate new block CPT1.
cpt_lf_alloc ->
Modify cpt_lf_alloc mailbox and its handler to
configure LFs from a block address out of multiple
blocks of same type. If a PF/VF needs to configure
LFs from both the blocks then this mbox should be
called twice.
Signed-off-by: Mahipal Challa <mchalla@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mdio_bus reset code first de-asserted the reset by allocating with
GPIOD_OUT_LOW, then asserted and de-asserted again. In other words, if
the reset signal defaulted to asserted, there'd be a short "spike"
before the reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
We then fsleep() and finally set the GPIO low at point C.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found when we pulled down the reset signal for the
Marvell 88E1512P PHY (because it requires at least 50ms after POR with
an active clock). Looking at the reset signal with a scope revealed a
short spike, point B in the artwork above.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210202143239.10714-1-mike.looijmans@topic.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable 'current_itr' is assigned to 0 before jumping to
'set_itr_now' but it has not been used after the jump. So, remove the
unneeded assignment.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Both of the statements are value assignment of the variable act_offset.
The first value assignment is overwritten by the second and is useless.
Remove it.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This change fixes the checkpatch warning described in this
commit cbacb5ab0aa0 ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The Intel I211 Ethernet Controller supports 2 Receive Side Scaling (RSS)
queues. It should not be excluded from having this feature enabled.
Via commit c883de9fd787 ("igb: rename igb define to be more generic")
E1000_MRQC_ENABLE_RSS_4Q was renamed to E1000_MRQC_ENABLE_RSS_MQ to
indicate that this is a generic bit flag to enable queues and not
a flag that is specific to devices that support 4 queues
The bit flag enables 2, 4 or 8 queues appropriately depending on the part.
Tested with a multicore CPU and frames were then distributed as expected.
This issue appears to have been introduced because of confusion caused
by the prior name.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.
Signed-off-by: Gal Hammer <ghammer@redhat.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.
_reg_dump method has been partially derived from i210 and have
same typo.
Suggested-by: Gal Hammer <ghammer@redhat.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
syzbot found WARNING in qrtr_tun_write_iter [1] when write_iter length
exceeds KMALLOC_MAX_SIZE causing order >= MAX_ORDER condition.
Additionally, there is no check for 0 length write.
[1]
WARNING: mm/page_alloc.c:5011
[..]
Call Trace:
alloc_pages_current+0x18c/0x2a0 mm/mempolicy.c:2267
alloc_pages include/linux/gfp.h:547 [inline]
kmalloc_order+0x2e/0xb0 mm/slab_common.c:837
kmalloc_order_trace+0x14/0x120 mm/slab_common.c:853
kmalloc include/linux/slab.h:557 [inline]
kzalloc include/linux/slab.h:682 [inline]
qrtr_tun_write_iter+0x8a/0x180 net/qrtr/tun.c:83
call_write_iter include/linux/fs.h:1901 [inline]
Reported-by: syzbot+c2a7e5c5211605a90865@syzkaller.appspotmail.com
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Link: https://lore.kernel.org/r/20210202092059.1361381-1-snovitoll@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Probe should return an error code if platform_get_irq_byname() fails
but it returns success instead.
Fixes: 6c30384eb1de ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXyFIl4V9hgxYM@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are several error handling bugs in mscc_ocelot_init_ports(). I
went through the code, and carefully audited it and made fixes and
cleanups.
1) The ocelot_probe_port() function didn't have a mirror release function
so it was hard to follow. I created the ocelot_release_port()
function.
2) In the ocelot_probe_port() function, if the register_netdev() call
failed, then it lead to a double free_netdev(dev) bug. Fix this by
setting "ocelot->ports[port] = NULL" on the error path.
3) I was concerned that the "port" which comes from of_property_read_u32()
might be out of bounds so I added a check for that.
4) In the original code if ocelot_regmap_init() failed then the driver
tried to continue but I think that should be a fatal error.
5) If ocelot_probe_port() failed then the most recent devlink was leaked.
The fix for mostly came Vladimir Oltean. Get rid of "registered_ports"
and just set a bit in "devlink_ports_registered" to say when the
devlink port has been registered (and needs to be unregistered on
error). There are fewer than 32 ports so a u32 is large enough for
this purpose.
6) The error handling if the final ocelot_port_devlink_init() failed had
two problems. The "while (port-- >= 0)" loop should have been
"--port" pre-op instead of a post-op to avoid a buffer underflow.
The "if (!registered_ports[port])" condition was reversed leading to
resource leaks and double frees.
Fixes: 6c30384eb1de ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXhqRxHtRGzSnJ@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When updating the tcp or udp header checksum on port nat the function
inet_proto_csum_replace2 with the last parameter pseudohdr as true.
This leads to an error in the case that GRO is used and packets are
split up in GSO. The tcp or udp checksum of all packets is incorrect.
The error is probably masked due to the fact the most network driver
implement tcp/udp checksum offloading. It also only happens when GRO is
applied and not on single packets.
The error is most visible when using a pppoe connection which is not
triggering the tcp/udp checksum offload.
Fixes: ac2a66665e23 ("netfilter: add generic flow table infrastructure")
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Although hooks are released via call_rcu(), chain and rule objects are
immediately released while packets are still walking over these bits.
This patch adds the .pre_exit callback which is invoked before
synchronize_rcu() in the netns framework to stay safe.
Remove a comment which is not valid anymore since the core does not use
synchronize_net() anymore since 8c873e219970 ("netfilter: core: free
hooks with call_rcu").
Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: df05ef874b28 ("netfilter: nf_tables: release objects on netns destruction")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
use date %Y instead of %G to read current year
Problem appeared when running lkp-tests on 01/01/2021
Fixes: 48d072c4e8cd ("selftests: netfilter: add time counter check")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When both --reap and --update flag are specified, there's a code
path at which the entry to be updated is reaped beforehand,
which then leads to kernel crash. Reap only entries which won't be
updated.
Fixes kernel bugzilla #207773.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=207773
Reported-by: Reindl Harald <h.reindl@thelounge.net>
Fixes: 0079c5aee348 ("netfilter: xt_recent: add an entry reaper")
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Adding support for Cinterion MV31 with PID 0x00B7.
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
P: Vendor=1e2d ProdID=00b7 Rev=04.14
S: Manufacturer=Cinterion
S: Product=Cinterion USB Mobile Broadband
S: SerialNumber=b3246eed
C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
Signed-off-by: Christoph Schemmel <christoph.schemmel@gmail.com>
Link: https://lore.kernel.org/r/20210202084523.4371-1-christoph.schemmel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
FUNC_1 mask not in use in i225 device and could be removed
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Local receiver mask SR_1000T_LOCAL_RX_STATUS not in use in i225 device
and could be removed
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use the strscpy method instead of strlcpy method.
See: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr
_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Extend reporting of NVM image version to include the gPHY (i225 PHY)
firmware version.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Expose the NVM map version via drvinfo in ethtool
NVM image version is reported as firmware version for i225 device
Minor typo fix - remove space
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This counter counts the number of good (non-erred) packets
transmitted sent by the host.
A good transmit packet is considered one that is 64 or more bytes
in length (from <Destination Address> through <CRC>,
inclusively) in length
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Multiple Tx Data Read Requests is hardware pipeline feature and
is not controlled by software
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
i225 device not supported and do not plan to support
configuration of fw version string for ethtool
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
valid_led_default function pointer not in use and can
be removed from nvm_operations structure.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Brian Vazquez says:
====================
net: use INDIRECT_CALL in some dst_ops
This patch series uses the INDIRECT_CALL wrappers in some dst_ops
functions to mitigate retpoline costs. Benefits depend on the
platform as described below.
Background: The kernel rewrites the retpoline code at
__x86_indirect_thunk_r11 depending on the CPU's requirements.
The INDIRECT_CALL wrappers provide hints on possible targets and
save the retpoline overhead using a direct call in case the
target matches one of the hints.
The retpoline overhead for the following three cases has been
measured by Luigi Rizzo in microbenchmarks, using CPU performance
counters, and cover reasonably well the range of possible retpoline
overheads compared to a plain indirect call (in equal conditions,
specifically with predicted branch, hot cache):
- just "jmp *(%r11)" on modern platforms like Intel Cascadelake.
In this case the overhead is just 2 clock cycles:
- "lfence; jmp *(%r11)" on e.g. some recent AMD CPUs.
In this case the lfence is blocked until pending reads complete,
so the actual overhead depends on previous instructions.
The best case we have measured 15 clock cycles of overhead.
- worst case, e.g. skylake, the full retpoline is used
__x86_indirect_thunk_r11: call set_u_target
capture_speculation: pause
lfence
jmp capture_speculation
.align 16
set_up_target: mov %r11, (%rsp)
ret
In this case the overhead has been measured in 35-40 clock cycles.
The actual time saved hence depends on the platform and current
clock speed (which varies heavily, especially when C-states are active).
Also note that actual benefit might be lower than expected if the
longer retpoline overlaps with some pending memory read.
MEASUREMENTS:
The INDIRECT_CALL wrappers in this patchset involve the processing
of incoming SYN and generation of syncookies. Hence, the test has been
run by configuring a receiving host with a single NIC rx queue, disabling
RPS and RFS so that all processing occurs on the same core.
An external source generates SYN fast enough to saturate the receiving CPU.
We ran two sets of experiments, with and without the dst_output patch,
comparing the number of syncookies generated over a 20s period
in multiple runs.
Assuming the CPU is saturated, the time per packet is
t = number_of_packets/total_time
and if the two datasets have statistically meaningful difference,
the difference in times between the two cases gives an estimate
of the benefits from one INDIRECT_CALL.
Here are the experimental results:
Skylake Syncookies over 20s (5 tests)
---------------------------------------------------
indirect 9166325 9182023 9170093 9134014 9171082
retpoline 9099308 9126350 9154841 9056377 9122376
Computing the stats on the ns_pkt = 20e6/total_packets gives the following:
$ ministat -c 95 -w 70 /tmp/sk-indirect /tmp/sk-retp
x /tmp/sk-indirect
+ /tmp/sk-retp
+----------------------------------------------------------------------+
|x xx x + x + + + +|
||______M__A_______|_|____________M_____A___________________| |
+----------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 5 2.17817e-06 2.18962e-06 2.181e-06 2.182292e-06 4.3252133e-09
+ 5 2.18464e-06 2.20839e-06 2.19241e-06 2.194974e-06 8.8695958e-09
Difference at 95.0% confidence
1.2682e-08 +/- 1.01766e-08
0.581132% +/- 0.466326%
(Student's t, pooled s = 6.97772e-09)
This suggests a difference of 13ns +/- 10ns
Our expectation from microbenchmarks was 35-40 cycles per call,
but part of the gains may be eaten by stalls from pending memory reads.
For Cascadelake:
Cascadelake Syncookies over 20s (5 tests)
---------------------------------------------------------
indirect 10339797 10297547 10366826 10378891 10384854
retpoline 10332674 10366805 10320374 10334272 10374087
Computing the stats on the ns_pkt = 20e6/total_packets gives no
meaningful difference even at just 80% (this was expected):
$ ministat -c 80 -w 70 /tmp/cl-indirect /tmp/cl-retp
x /tmp/cl-indirect
+ /tmp/cl-retp
+----------------------------------------------------------------------+
| x x + * x + + + x|
||______________|_M_________A_____A_______M________|___| |
+----------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 5 1.92588e-06 1.94221e-06 1.92923e-06 1.931716e-06 6.6936746e-09
+ 5 1.92788e-06 1.93791e-06 1.93531e-06 1.933188e-06 4.3734106e-09
No difference proven at 80.0% confidence
====================
Link: https://lore.kernel.org/r/20210201174132.3534118-1-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch avoids the indirect call for the common case:
ip6_dst_check and ipv4_dst_check
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch avoids the indirect call for the common case:
ip6_mtu and ipv4_mtu
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch avoids the indirect call for the common case:
ip6_output and ip_output
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch avoids the indirect call for the common case:
ip_local_deliver and ip6_input
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1ccc ("tasklet: Introduce new initialization API")
It is unfortunate that we need to add a pointer to the driver context to
get back to the usbnet device, but the space will be reclaimed once
there are no more users of the old API left and we can remove the data
value and flag from the tasklet struct.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210130234637.26505-1-kernel@esmil.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since I wrote the below patch if you run a debug kernel you can a
dma debug warning like:
nouveau 0000:1f:00.0: DMA-API: device driver tries to sync DMA memory it has not allocated [device address=0x000000016e012000] [size=4096 bytes]
The old nouveau code wasn't consolidate the pages like the ttm code,
but the dma-debug expects the sync code to give it the same base/range
pairs as the allocator.
Fix the nouveau sync code to consolidate pages before calling the
sync code.
Fixes: bd549d35b4be0 ("nouveau: use ttm populate mapping functions. (v2)")
Reported-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/417588/
|
|
On 32-bit architecture, roundup_pow_of_two() can return 0 when the argument
has upper most bit set due to resulting 1UL << 32. Add a check for this case.
Fixes: d5a3b1f69186 ("bpf: introduce BPF_MAP_TYPE_STACK_TRACE")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210127063653.3576-1-minhquangbui99@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
- Make sure to set a default console, otherwise ttynull is selected
- Revert initial ARCH_HAS_SET_MEMORY support, this needs more work
- Fix a regression due to ubd refactoring
- Various small fixes
* tag 'for-linus-5.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: time: fix initialization in time-travel mode
um: fix os_idle_sleep() to not hang
Revert "um: support some of ARCH_HAS_SET_MEMORY"
Revert "um: allocate a guard page to helper threads"
um: virtio: free vu_dev only with the contained struct device
um: kmsg_dumper: always dump when not tty console
um: stdio_console: Make preferred console
um: return error from ioremap()
um: ubd: fix command line handling of ubd
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"Fix the arm64 linear map range detection for tagged addresses and
replace the bitwise operations with subtract (virt_addr_valid(),
__is_lm_address(), __lm_to_phys())"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Use simpler arithmetics for the linear map macros
arm64: Do not pass tagged addresses to __is_lm_address()
|
