| Age | Commit message (Collapse) | Author |
|---|
|
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
Amend the filtering appropriately.
Fixes: 57fb32e632be ("drm/vc4: hdmi: Block odd horizontal timings")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127135116.298278-1-maxime@cerno.tech
|
|
The code that set the scdc_enabled flag to ensure it was
disabled at boot time also ran on Pi0-3 where there is no
SCDC support. This lead to a warning in vc4_hdmi_encoder_post_crtc_disable
due to vc4_hdmi_disable_scrambling being called and trying to
read (and write) register HDMI_SCRAMBLER_CTL which doesn't
exist on those platforms.
Only set the flag should the interface be configured to support
more than HDMI 1.4.
Fixes: 1998646129fa ("drm/vc4: hdmi: Introduce a scdc_enabled flag")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127134559.292778-1-maxime@cerno.tech
|
|
The existing logic was flawed in that it could try reading the
2711 specific registers for HPD on a CM1/3 where the HPD GPIO
hadn't been defined in DT.
Ensure we don't do the 2711 register read on invalid hardware,
and then
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127131754.236074-1-maxime@cerno.tech
|
|
This reverts commit 54d516b1d62ff8f17cee2da06e5e4706a0d00b8a
That commit did a refactoring that effectively combined fast and slow
gup paths (again). And that was again incorrect, for two reasons:
a) Fast gup and slow gup get reference counts on pages in different
ways and with different goals: see Linus' writeup in commit
cd1adf1b63a1 ("Revert "mm/gup: remove try_get_page(), call
try_get_compound_head() directly""), and
b) try_grab_compound_head() also has a specific check for
"FOLL_LONGTERM && !is_pinned(page)", that assumes that the caller
can fall back to slow gup. This resulted in new failures, as
recently report by Will McVicker [1].
But (a) has problems too, even though they may not have been reported
yet. So just revert this.
Link: https://lore.kernel.org/r/20220131203504.3458775-1-willmcvicker@google.com [1]
Fixes: 54d516b1d62f ("mm/gup: small refactoring: simplify try_grab_page()")
Reported-and-tested-by: Will McVicker <willmcvicker@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Minchan Kim <minchan@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: stable@vger.kernel.org # 5.15
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fix missed change for PTR->PTR_WD conversion
- kernel-doc fixes
* tag 'mips-fixes-5.17_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: KVM: fix vz.c kernel-doc notation
MIPS: octeon: Fix missed PTR->PTR_WD conversion
|
|
When kernel boots with a NUMA topology with some NUMA nodes offline, the PCI
driver should only set an online NUMA node on the device. This can happen
during KDUMP where some NUMA nodes are not made online by the KDUMP kernel.
This patch also fixes the case where kernel is booting with "numa=off".
Fixes: 999dd956d838 ("PCI: hv: Add support for protocol 1.3 and support PCI_BUS_RELATIONS2")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Purna Pavan Chandra Aekkaladevi <paekkaladevi@microsoft.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/1643247814-15184-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
In function do_fb_ioctl(), the "arg" is the type of unsigned long,
and in "case FBIOBLANK:" this argument is casted into an int before
passig to fb_blank(). In fb_blank(), the comparision
if (blank > FB_BLANK_POWERDOWN) would be bypass if the original
"arg" is a large number, which is possible because it comes from
the user input. Fix this by adding the check before the function
call.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Yizhuo Zhai <yzhai003@ucr.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202235811.1621017-1-yzhai003@ucr.edu
|
|
Adds a driver private tee_context by moving the tee_context in struct
optee_notif to struct optee. This tee_context was previously used when
doing internal calls to secure world to deliver notification.
The new driver internal tee_context is now also when allocating driver
private shared memory. This decouples the shared memory object from its
original tee_context. This is needed when the life time of such a memory
allocation outlives the client tee_context.
This patch fixes the problem described below:
The addition of a shutdown hook by commit f25889f93184 ("optee: fix tee out
of memory failure seen during kexec reboot") introduced a kernel shutdown
regression that can be triggered after running the OP-TEE xtest suites.
Once the shutdown hook is called it is not possible to communicate any more
with the supplicant process because the system is not scheduling task any
longer. Thus if the optee driver shutdown path receives a supplicant RPC
request from the OP-TEE we will deadlock the kernel's shutdown.
Fixes: f25889f93184 ("optee: fix tee out of memory failure seen during kexec reboot")
Fixes: 217e0250cccb ("tee: use reference counting for tee_context")
Reported-by: Lars Persson <larper@axis.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
Cortex-A510's erratum #2077057 causes SPSR_EL2 to be corrupted when
single-stepping authenticated ERET instructions. A single step is
expected, but a pointer authentication trap is taken instead. The
erratum causes SPSR_EL1 to be copied to SPSR_EL2, which could allow
EL1 to cause a return to EL2 with a guest controlled ELR_EL2.
Because the conditions require an ERET into active-not-pending state,
this is only a problem for the EL2 when EL2 is stepping EL1. In this case
the previous SPSR_EL2 value is preserved in struct kvm_vcpu, and can be
restored.
Cc: stable@vger.kernel.org # 53960faf2b73: arm64: Add Cortex-A510 CPU part definition
Cc: stable@vger.kernel.org
Signed-off-by: James Morse <james.morse@arm.com>
[maz: fixup cpucaps ordering]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220127122052.1584324-5-james.morse@arm.com
|
|
Prior to commit defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to
HYP"), when an SError is synchronised due to another exception, KVM
handles the SError first. If the guest survives, the instruction that
triggered the original exception is re-exectued to handle the first
exception. HVC is treated as a special case as the instruction wouldn't
normally be re-exectued, as its not a trap.
Commit defe21f49bc9 didn't preserve the behaviour of the 'return 1'
that skips the rest of handle_exit().
Since commit defe21f49bc9, KVM will try to handle the SError and the
original exception at the same time. When the exception was an HVC,
fixup_guest_exit() has already rolled back ELR_EL2, meaning if the
guest has virtual SError masked, it will execute and handle the HVC
twice.
Restore the original behaviour.
Fixes: defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to HYP")
Cc: stable@vger.kernel.org
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220127122052.1584324-4-james.morse@arm.com
|
|
When any exception other than an IRQ occurs, the CPU updates the ESR_EL2
register with the exception syndrome. An SError may also become pending,
and will be synchronised by KVM. KVM notes the exception type, and whether
an SError was synchronised in exit_code.
When an exception other than an IRQ occurs, fixup_guest_exit() updates
vcpu->arch.fault.esr_el2 from the hardware register. When an SError was
synchronised, the vcpu esr value is used to determine if the exception
was due to an HVC. If so, ELR_EL2 is moved back one instruction. This
is so that KVM can process the SError first, and re-execute the HVC if
the guest survives the SError.
But if an IRQ synchronises an SError, the vcpu's esr value is stale.
If the previous non-IRQ exception was an HVC, KVM will corrupt ELR_EL2,
causing an unrelated guest instruction to be executed twice.
Check ARM_EXCEPTION_CODE() before messing with ELR_EL2, IRQs don't
update this register so don't need to check.
Fixes: defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to HYP")
Cc: stable@vger.kernel.org
Reported-by: Steven Price <steven.price@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220127122052.1584324-3-james.morse@arm.com
|
|
mxsfb should not ever dereference the NULL pointer which
drm_atomic_get_new_bridge_state is allowed to return.
Assume a fixed format instead.
Fixes: b776b0f00f24 ("drm: mxsfb: Use bus_format from the nearest bridge if present")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220202081755.145716-3-alexander.stein@ew.tq-group.com
|
|
SAR GEO offsets are not supported on 3160 devices. The code was
refactored and caused us to start sending the command anyway, which
causes a FW assertion failure. Fix that only considering this feature
supported on FW API with major version is 17 if the device is not
3160.
Additionally, fix the caller of iwl_mvm_sar_geo_init() so that it
checks for the return value, which it was ignoring.
Reported-by: Len Brown <lenb@kernel.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 78a19d5285d9 ("iwlwifi: mvm: Read the PPAG and SAR tables at INIT stage")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128144623.96f683a89b42.I14e2985bfd7ddd8a8d83eb1869b800c0e7f30db4@changeid
|
|
This feature has been deprecated and should not be used anymore. With
newer firmwares, namely *-67.ucode and above, trying to use it causes an
assertion failure in the FW, similar to this:
[Tue Jan 11 20:05:24 2022] iwlwifi 0000:04:00.0: 0x00001062 | ADVANCED_SYSASSERT
In order to prevent this feature from being used, remove it entirely
and get rid of the Kconfig option that
enables it (IWLWIFI_BCAST_FILTERING).
Fixes: cbaa6aeedee5 ("iwlwifi: bump FW API to 67 for AX devices")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215488
Cc: stable@vger.kernel.org # 5.16.x
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128144623.9241e049f13e.Ia4f282813ca2ddd24c13427823519113f2bbebf2@changeid
|
|
When we register and we are in link protection passive, meaning
that the host can't touch the device, report RFKILL immediately
upon register() and don't wait for the CSME firmware to let us
know again about the link protection state.
What happens if we wait is that the host will not see RFKILL soon
enough and we'll have a window of time during which it can bring
up the device which will request ownership.
Fixes: 2da4366f9e2c ("iwlwifi: mei: add the driver to allow cooperation with CSME")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.a136f9f46336.Ief7506dc3b1813a1943a5a639aa45d8e5f284f31@changeid
|
|
iwlmei can trigger a hardware RFKILL when the CSME firmware
does not want the host to touch the device.
But then, iwlmvm reports RFKILL which makes cfg80211 update
iwlmvm about RFKILL. iwlmvm then thinks there is a change in
the _software_ rfkill and it calls rfkill_blocked() to fetch
the RFKILL state. This returns that RFKILL is blocked (because
of iwlmei) and iwlmvm tells iwlmei that _software_ RFKILL is
asserted.
This is a bug of course.
Fix this by checking explicitly the software RFKILL state and
not the overall RFKILL state.
Fixes: 7ce1f2157e14 ("iwlwifi: mvm: read the rfkill state and feed it to iwlmei")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 7ce1f2157e14 ("iwlwifi: mvm: read the rfkill state and feed it to iwlmei")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.f293861a3f92.I9553d27df1de6fd5756a43ea5f8b89d06fa1a6f2@changeid
|
|
The shared area is a DMA memory allocated in the host and
mapped so that the host and the CSME firmware can
exchange data. It is mapped through a dedicated PCI device
that is driven by the mei bus driver.
The bus driver is in charge of allocating and mapping this
memory. It also needs to configure the CSME firmware with
a specific set of commands, so that the CSME firmware will
know that this memory is meant to be used by its internal
WLAN module.
For this, the CSME firmware first needs to completely
initialize its WLAN module and only then get the mapping
request.
The problem is that the mei bus enumeration completes
before the WLAN is completely ready. This means that
the WLAN module's initialization is racing with iwlmei's
allocation and mapping flow.
Testing showed a problem in resume flows where iwlmei
was too fast and the DMA mapping failed.
Add a retry mechanism to make sure that we will succeed
to map the memory.
Fixes: 2da4366f9e2c ("iwlwifi: mei: add the driver to allow cooperation with CSME")
Fixes: bcbddc4f9d02 ("iwlwifi: mei: wait before mapping the shared area")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.cc51e6a6d635.I4b74a082eb8d89f9e4f556a27c4339c15444dc6c@changeid
|
|
The check makes sure that we can look at the ip header.
We first need to check that the basic ip header (20 bytes)
can be pulled before we look at the field that will teach
us how long is the ip header. This is why there are two
checks.
The second check was wrong and smatch pointed that
sizeof(ip_hdrlen(skb) - sizeof(*iphdr)) can't be right.
Looking at the code again made me think that we really
need ip_hdrlen(skb) since we want to make sure all the
IP header is in the buffer header. This will allow us
to set the transport offset and from there to look
at the transport header (TCP / UDP).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 2da4366f9e2c ("iwlwifi: mei: add the driver to allow cooperation with CSME")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.6d9fcf82691e.I449b1e21c5b5478f2ac218522570479918f49f9d@changeid
|
|
If we run into this error path, we shouldn't unlock the mutex
since it's not locked since. Fix this in the gen2 code as well.
Fixes: eda50cde58de ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.b8b0dfce16ef.Ie20f0f7b23e5911350a2766524300d2915e7b677@changeid
|
|
If we run into this error path, we shouldn't unlock the mutex
since it's not locked since. Fix this.
Fixes: a6bd005fe92d ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.5d16821d1433.Id259699ddf9806459856d6aefbdbe54477aecffd@changeid
|
|
There are a couple of bugs in this function:
1. It is declared as a non-static function, even though
it's only used in one file.
2. Its return value should be of type u32 but it returns
(in some cases) -1.
Fix them by making this function static and returning an
error value of type unsigned.
In addition, we're assigning the return value of this function
as the legacy rate even if the function returned an error value.
Fix this by assigning the lowest rate in this case.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reported-by: Ye Guojin <ye.guojin@zte.com.cn>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Fixes: 9998f81e4ba5 ("iwlwifi: mvm: convert old rate & flags to the new format.")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.5612eeb9d6d0.I992e10d93fc22919b2bc42daad087ee1b5d6f014@changeid
|
|
We're checking the FW version of TX_CMD in order to decide whether to
convert rate_n_flags from the old format to the new one. If the API
is smaller or equal to 6 we should convert it. Currently we're
converting if the API version is greater than 6. Fix it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Fixes: dc52fac37c87 ("iwlwifi: mvm: Support new TX_RSP and COMPRESSED_BA_RES versions")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.a264ac51d106.I228ba1317cdcbfef931c09d280d701fcad9048d2@changeid
|
|
This started out with me noticing that "dom0_max_vcpus=<N>" with <N>
larger than the number of physical CPUs reported through ACPI tables
would not bring up the "excess" vCPU-s. Addressing this is the primary
purpose of the change; CPU maps handling is being tidied only as far as
is necessary for the change here (with the effect of also avoiding the
setting up of too much per-CPU infrastructure, i.e. for CPUs which can
never come online).
Noticing that xen_fill_possible_map() is called way too early, whereas
xen_filter_cpu_maps() is called too late (after per-CPU areas were
already set up), and further observing that each of the functions serves
only one of Dom0 or DomU, it looked like it was better to simplify this.
Use the .get_smp_config hook instead, uniformly for Dom0 and DomU.
xen_fill_possible_map() can be dropped altogether, while
xen_filter_cpu_maps() is re-purposed but not otherwise changed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/2dbd5f0a-9859-ca2d-085e-a02f7166c610@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Add missing ioctl "magic numbers" for various Xen interfaces
(xenbus_dev.h, gntalloc.h, gntdev.h, and privcmd.h).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: xen-devel@lists.xenproject.org
Link: https://lore.kernel.org/r/20220131161959.16509-1-rdunlap@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
--------------cKY3Ggs6VDUCSn4I6iN78sHA
Content-Type: multipart/mixed; boundary="------------g0T69ASidFiPhh4eOY4XzIg1"
--------------g0T69ASidFiPhh4eOY4XzIg1
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: quoted-printable
The current implementation of gntdev guarantees that the first call to
IOCTL_GNTDEV_MAP_GRANT_REF will set @index to 0. This is required to
use gntdev for Wayland, which is a future desire of Qubes OS.
Additionally, requesting zero grants results in an error, but this was
not documented either. Document both of these.
Signed-off-by: Demi Marie Obenour <demiobenour@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/f66c5a4e-2034-00b5-a635-6983bd999c07@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
It is better/preferred not to include file names in source files
because (a) they are not needed and (b) they can be incorrect,
so just delete this incorrect file name.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: xen-devel@lists.xenproject.org
Link: https://lore.kernel.org/r/20220130191705.24971-1-rdunlap@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
After commit 2fd3fb0be1d1 ("kasan, vmalloc: unpoison VM_ALLOC pages
after mapping"), non-VM_ALLOC mappings will be marked as accessible
in __get_vm_area_node() when KASAN is enabled. But now the flag for
ringbuf area is VM_ALLOC, so KASAN will complain out-of-bound access
after vmap() returns. Because the ringbuf area is created by mapping
allocated pages, so use VM_MAP instead.
After the change, info in /proc/vmallocinfo also changes from
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmalloc user
to
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmap user
Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: syzbot+5ad567a418794b9b5983@syzkaller.appspotmail.com
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220202060158.6260-1-houtao1@huawei.com
|
|
Controller deletion/reset, immediately followed by or concurrent with
a reconnect, is hard failing the connect attempt resulting in a
complete loss of connectivity to the controller.
In the connect request, fabrics looks for an existing controller with
the same address components and aborts the connect if a controller
already exists and the duplicate connect option isn't set. The match
routine filters out controllers that are dead or dying, so they don't
interfere with the new connect request.
When NVME_CTRL_DELETING_NOIO was added, it missed updating the state
filters in the nvmf_ctlr_matches_baseopts() routine. Thus, when in this
new state, it's seen as a live controller and fails the connect request.
Correct by adding the DELETING_NIO state to the match checks.
Fixes: ecca390e8056 ("nvme: fix deadlock in disconnect during scan_work and/or ana_work")
Cc: <stable@vger.kernel.org> # v5.7+
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Set workstation_name from the master_tcon for multiuser mounts.
Just in case, protect size_of_ntlmssp_blob against a NULL workstation_name.
Fixes: 49bd49f983b5 ("cifs: send workstation name during ntlmssp session setup")
Cc: stable@vger.kernel.org # 5.16
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Ryan Bair <ryandbair@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
For example if mtime or size has changed.
Signed-off-by: Rohith Surabattula <rohiths@microsoft.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
neigh_managed_work
syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]:
kworker/0:16/14617 is trying to acquire lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
[...]
but task is already holding lock:
ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572
The neighbor entry turned to NUD_FAILED state, where __neigh_event_send()
triggered an immediate probe as per commit cd28ca0a3dd1 ("neigh: reduce
arp latency") via neigh_probe() given table lock was held.
One option to fix this situation is to defer the neigh_probe() back to
the neigh_timer_handler() similarly as pre cd28ca0a3dd1. For the case
of NTF_MANAGED, this deferral is acceptable given this only happens on
actual failure state and regular / expected state is NUD_VALID with the
entry already present.
The fix adds a parameter to __neigh_event_send() in order to communicate
whether immediate probe is allowed or disallowed. Existing call-sites
of neigh_event_send() default as-is to immediate probe. However, the
neigh_managed_work() disables it via use of neigh_event_send_probe().
[0] <TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2956 [inline]
check_deadlock kernel/locking/lockdep.c:2999 [inline]
validate_chain kernel/locking/lockdep.c:3788 [inline]
__lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027
lock_acquire kernel/locking/lockdep.c:5639 [inline]
lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604
__raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline]
_raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334
___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652
ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123
__ip6_finish_output net/ipv6/ip6_output.c:191 [inline]
__ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170
ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224
dst_output include/net/dst.h:451 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508
ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650
ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742
neigh_probe+0xc2/0x110 net/core/neighbour.c:1040
__neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201
neigh_event_send include/net/neighbour.h:470 [inline]
neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574
process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307
worker_thread+0x657/0x1110 kernel/workqueue.c:2454
kthread+0x2e9/0x3a0 kernel/kthread.c:377
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
</TASK>
Fixes: 7482e3841d52 ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Reported-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Tested-by: syzbot+5239d0e1778a500d477a@syzkaller.appspotmail.com
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220201193942.5055-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcp_shift_skb_data() might collapse three packets into a larger one.
P_A, P_B, P_C -> P_ABC
Historically, it used a single tcp_skb_can_collapse_to(P_A) call,
because it was enough.
In commit 85712484110d ("tcp: coalesce/collapse must respect MPTCP extensions"),
this call was replaced by a call to tcp_skb_can_collapse(P_A, P_B)
But the now needed test over P_C has been missed.
This probably broke MPTCP.
Then later, commit 9b65b17db723 ("net: avoid double accounting for pure zerocopy skbs")
added an extra condition to tcp_skb_can_collapse(), but the missing call
from tcp_shift_skb_data() is also breaking TCP zerocopy, because P_A and P_C
might have different skb_zcopy_pure() status.
Fixes: 85712484110d ("tcp: coalesce/collapse must respect MPTCP extensions")
Fixes: 9b65b17db723 ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220201184640.756716-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add myself as a reviewer for the libata PATA drivers -- there is
activity in this area still... 8-)
Having been hacking on ATA from the early 90s, I think I deserved this
highly responsible position, at last! :-)
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
We probably never trigger this, but the logic inside the check is
inverted.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
dGPUs connected to Intel systems configured for suspend to idle
will not have the power rails cut at suspend and resetting the GPU
may lead to problematic behaviors.
Fixes: e25443d2765f4 ("drm/amdgpu: add a dev_pm_ops prepare callback (v2)")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1879
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
panels
The eDP link rate reported by the DP_MAX_LINK_RATE dpcd register (0xa) is
contradictory to the highest rate supported reported by
EDID (0xc = LINK_RATE_RBR2). The effects of this compounded with commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")' results
in no display modes being found and a dark panel.
For now, simply force the maximum supported link rate for the eDP attached
2018 15" Apple Retina panels.
Additionally, we must also check the firmware revision since the device ID
reported by the DPCD is identical to that of the more capable 16,1,
incorrectly quirking it. We also use said firmware check to quirk the
refreshed 15,1 models with Vega graphics as they use a slightly newer
firmware version.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
This change causes regression, that prevents some systems
from lighting up internal displays.
[How]
Revert this patch until a new solution is ready.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
The original latencies were causing underflow in some modes.
Resolution: 2880x1620@60p when HDR enable
[How]
1. Replace with the up-to-date watermark values based on new measurments
2. Correct the ddr_wm_table name to DDR5 on DCN31
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
There is underflow / visual corruption DCN301, for high
bandwidth MST DSC configurations such as 2x1440p144 or 2x4k60.
[How]
Use up-to-date watermark values for DCN301.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We observed a GPU hang when querying GMC CG state(i.e.,
cat amdgpu_pm_info) on cyan skillfish. Acctually, cyan
skillfish doesn't support any CG features.
Just prevent it from accessing GMC CG registers.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This will cause misconfigured systems to not run the GPU suspend
routines.
* In APUs that are properly configured system will go into s2idle.
* In APUs that are intended to be S3 but user selects
s2idle the GPU will stay fully powered for the suspend.
* In APUs that are intended to be s2idle and system misconfigured
the GPU will stay fully powered for the suspend.
* In systems that are intended to be s2idle, but AMD dGPU is also
present, the dGPU will go through S3
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This will be used to help make decisions on what to do in
misconfigured systems.
v2: squash in semicolon fix from Stephen Rothwell
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In __WARN_FLAGS(), we had two asm statements (abbreviated):
asm volatile("ud2");
asm volatile(".pushsection .discard.reachable");
These pair of statements are used to trigger an exception, but then help
objtool understand that for warnings, control flow will be restored
immediately afterwards.
The problem is that volatile is not a compiler barrier. GCC explicitly
documents this:
> Note that the compiler can move even volatile asm instructions
> relative to other code, including across jump instructions.
Also, no clobbers are specified to prevent instructions from subsequent
statements from being scheduled by compiler before the second asm
statement. This can lead to instructions from subsequent statements
being emitted by the compiler before the second asm statement.
Providing a scheduling model such as via -march= options enables the
compiler to better schedule instructions with known latencies to hide
latencies from data hazards compared to inline asm statements in which
latencies are not estimated.
If an instruction gets scheduled by the compiler between the two asm
statements, then objtool will think that it is not reachable, producing
a warning.
To prevent instructions from being scheduled in between the two asm
statements, merge them.
Also remove an unnecessary unreachable() asm annotation from BUG() in
favor of __builtin_unreachable(). objtool is able to track that the ud2
from BUG() terminates control flow within the function.
Link: https://gcc.gnu.org/onlinedocs/gcc/Extended-Asm.html#Volatile
Link: https://github.com/ClangBuiltLinux/linux/issues/1483
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220202205557.2260694-1-ndesaulniers@google.com
|
|
Merge series from Mark Brown <broonie@kernel.org>:
The event generation coverage I just wrote shows that the generic ASoC
ops fail to generate events for stereo controls when only the first
channel is changed, we just return the status for the second channel and
discard that for the first.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Notable bug fixes:
- Ensure SM_NOTIFY doesn't crash the NFS server host
- Ensure NLM locks are cleaned up after client reboot
- Fix a leak of internal NFSv4 lease information"
* tag 'nfsd-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: nfsd4_setclientid_confirm mistakenly expires confirmed client.
lockd: fix failure to cleanup client locks
lockd: fix server crash on reboot of client holding lock
|
|
Leon reported NULL pointer deref with nowait support:
[ 15.123761] device-mapper: raid: Loading target version 1.15.1
[ 15.124185] device-mapper: raid: Ignoring chunk size parameter for RAID 1
[ 15.124192] device-mapper: raid: Choosing default region size of 4MiB
[ 15.129524] BUG: kernel NULL pointer dereference, address: 0000000000000060
[ 15.129530] #PF: supervisor write access in kernel mode
[ 15.129533] #PF: error_code(0x0002) - not-present page
[ 15.129535] PGD 0 P4D 0
[ 15.129538] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 15.129541] CPU: 5 PID: 494 Comm: ldmtool Not tainted 5.17.0-rc2-1-mainline #1 9fe89d43dfcb215d2731e6f8851740520778615e
[ 15.129546] Hardware name: Gigabyte Technology Co., Ltd. X570 AORUS ELITE/X570 AORUS ELITE, BIOS F36e 10/14/2021
[ 15.129549] RIP: 0010:blk_queue_flag_set+0x7/0x20
[ 15.129555] Code: 00 00 00 0f 1f 44 00 00 48 8b 35 e4 e0 04 02 48 8d 57 28 bf 40 01 \
00 00 e9 16 c1 be ff 66 0f 1f 44 00 00 0f 1f 44 00 00 89 ff <f0> 48 0f ab 7e 60 \
31 f6 89 f7 c3 66 66 2e 0f 1f 84 00 00 00 00 00
[ 15.129559] RSP: 0018:ffff966b81987a88 EFLAGS: 00010202
[ 15.129562] RAX: ffff8b11c363a0d0 RBX: ffff8b11e294b070 RCX: 0000000000000000
[ 15.129564] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 000000000000001d
[ 15.129566] RBP: ffff8b11e294b058 R08: 0000000000000000 R09: 0000000000000000
[ 15.129568] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8b11e294b070
[ 15.129570] R13: 0000000000000000 R14: ffff8b11e294b000 R15: 0000000000000001
[ 15.129572] FS: 00007fa96e826780(0000) GS:ffff8b18deb40000(0000) knlGS:0000000000000000
[ 15.129575] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 15.129577] CR2: 0000000000000060 CR3: 000000010b8ce000 CR4: 00000000003506e0
[ 15.129580] Call Trace:
[ 15.129582] <TASK>
[ 15.129584] md_run+0x67c/0xc70 [md_mod 1e470c1b6bcf1114198109f42682f5a2740e9531]
[ 15.129597] raid_ctr+0x134a/0x28ea [dm_raid 6a645dd7519e72834bd7e98c23497eeade14cd63]
[ 15.129604] ? dm_split_args+0x63/0x150 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129615] dm_table_add_target+0x188/0x380 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129625] table_load+0x13b/0x370 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129635] ? dev_suspend+0x2d0/0x2d0 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129644] ctl_ioctl+0x1bd/0x460 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129655] dm_ctl_ioctl+0xa/0x20 [dm_mod 0d7b0bc3414340a79c4553bae5ca97294b78336e]
[ 15.129663] __x64_sys_ioctl+0x8e/0xd0
[ 15.129667] do_syscall_64+0x5c/0x90
[ 15.129672] ? syscall_exit_to_user_mode+0x23/0x50
[ 15.129675] ? do_syscall_64+0x69/0x90
[ 15.129677] ? do_syscall_64+0x69/0x90
[ 15.129679] ? syscall_exit_to_user_mode+0x23/0x50
[ 15.129682] ? do_syscall_64+0x69/0x90
[ 15.129684] ? do_syscall_64+0x69/0x90
[ 15.129686] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 15.129689] RIP: 0033:0x7fa96ecd559b
[ 15.129692] Code: ff ff ff 85 c0 79 9b 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c \
c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff \
ff 73 01 c3 48 8b 0d a5 a8 0c 00 f7 d8 64 89 01 48
[ 15.129696] RSP: 002b:00007ffcaf85c258 EFLAGS: 00000206 ORIG_RAX: 0000000000000010
[ 15.129699] RAX: ffffffffffffffda RBX: 00007fa96f1b48f0 RCX: 00007fa96ecd559b
[ 15.129701] RDX: 00007fa97017e610 RSI: 00000000c138fd09 RDI: 0000000000000003
[ 15.129702] RBP: 00007fa96ebab583 R08: 00007fa97017c9e0 R09: 00007ffcaf85bf27
[ 15.129704] R10: 0000000000000001 R11: 0000000000000206 R12: 00007fa97017e610
[ 15.129706] R13: 00007fa97017e640 R14: 00007fa97017e6c0 R15: 00007fa97017e530
[ 15.129709] </TASK>
This is caused by missing mddev->queue check for setting QUEUE_FLAG_NOWAIT
Fix this by moving the QUEUE_FLAG_NOWAIT logic to under mddev->queue check.
Fixes: f51d46d0e7cb ("md: add support for REQ_NOWAIT")
Reported-by: Leon Möller <jkhsjdhjs@totally.rip>
Tested-by: Leon Möller <jkhsjdhjs@totally.rip>
Cc: Vishal Verma <vverma@digitalocean.com>
Signed-off-by: Song Liu <song@kernel.org>
|
|
We're missing the `f` prefix to have python do string interpolation, so
we'd never end up printing what the actual "unexpected" error is.
Fixes: ee92ed38364e ("kunit: add run_checks.py script to validate kunit changes")
Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fanotify fix from Jan Kara:
"Fix stale file descriptor in copy_event_to_user"
* tag 'fsnotify_for_v5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: Fix stale file descriptor in copy_event_to_user()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"A single fix to an error seen on qemu due to a missing import"
* tag 'linux-kselftest-kunit-fixes-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: tool: Import missing importlib.abc
|
|
Both msgr1 and msgr2 in crc mode are zero copy in the sense that
message data is read from the socket directly into the destination
buffer. We assume that the destination buffer is stable (i.e. remains
unchanged while it is being read to) though. Otherwise, CRC errors
ensue:
libceph: read_partial_message 0000000048edf8ad data crc 1063286393 != exp. 228122706
libceph: osd1 (1)192.168.122.1:6843 bad crc/signature
libceph: bad data crc, calculated 57958023, expected 1805382778
libceph: osd2 (2)192.168.122.1:6876 integrity error, bad crc
Introduce rxbounce option to enable use of a bounce buffer when
receiving message data. In particular this is needed if a mapped
image is a Windows VM disk, passed to QEMU. Windows has a system-wide
"dummy" page that may be mapped into the destination buffer (potentially
more than once into the same buffer) by the Windows Memory Manager in
an effort to generate a single large I/O [1][2]. QEMU makes a point of
preserving overlap relationships when cloning I/O vectors, so krbd gets
exposed to this behaviour.
[1] "What Is Really in That MDL?"
https://docs.microsoft.com/en-us/previous-versions/windows/hardware/design/dn614012(v=vs.85)
[2] https://blogs.msmvps.com/kernelmustard/2005/05/04/dummy-pages/
URL: https://bugzilla.redhat.com/show_bug.cgi?id=1973317
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
|
