| Age | Commit message (Collapse) | Author |
|---|
|
The increment of buff is indented one level too deeply, clean
this up by removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20190314230838.18256-1-colin.king@canonical.com
|
|
The inclusion of <linux/kernel.h> was causing issue as the definition of
__arch_hweight64 from arch/x86/include/asm/arch_hweight.h eventually gets
included. The definition is problematic when compiled with -m16 (all code
in arch/x86/boot/ is) as the "D" inline assembly constraint is rejected
by both compilers when passed an argument of type long long (regardless
of signedness, anything smaller is fine).
Because GCC performs inlining before semantic analysis, and
__arch_hweight64 is dead in this translation unit, GCC does not report
any issues at compile time. Clang does the semantic analysis in the
front end, before inlining (run in the middle) can determine the code is
dead. I consider this another case of PR33587, which I think we can do
more work to solve.
It turns out that arch/x86/boot/string.c doesn't actually need
linux/kernel.h, simply linux/limits.h and linux/compiler.h.
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: bp@alien8.de
Cc: niravd@google.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chao Fan <fanc.fnst@cn.fujitsu.com>
Cc: Uros Bizjak <ubizjak@gmail.com>
Link: https://bugs.llvm.org/show_bug.cgi?id=33587
Link: https://github.com/ClangBuiltLinux/linux/issues/347
Link: https://lkml.kernel.org/r/20190314221458.83047-1-ndesaulniers@google.com
|
|
Syzkaller hit 'KASAN: use-after-free Write in sanitize_ptr_alu' bug.
Call trace:
dump_stack+0xbf/0x12e
print_address_description+0x6a/0x280
kasan_report+0x237/0x360
sanitize_ptr_alu+0x85a/0x8d0
adjust_ptr_min_max_vals+0x8f2/0x1ca0
adjust_reg_min_max_vals+0x8ed/0x22e0
do_check+0x1ca6/0x5d00
bpf_check+0x9ca/0x2570
bpf_prog_load+0xc91/0x1030
__se_sys_bpf+0x61e/0x1f00
do_syscall_64+0xc8/0x550
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fault injection trace:
kfree+0xea/0x290
free_func_state+0x4a/0x60
free_verifier_state+0x61/0xe0
push_stack+0x216/0x2f0 <- inject failslab
sanitize_ptr_alu+0x2b1/0x8d0
adjust_ptr_min_max_vals+0x8f2/0x1ca0
adjust_reg_min_max_vals+0x8ed/0x22e0
do_check+0x1ca6/0x5d00
bpf_check+0x9ca/0x2570
bpf_prog_load+0xc91/0x1030
__se_sys_bpf+0x61e/0x1f00
do_syscall_64+0xc8/0x550
entry_SYSCALL_64_after_hwframe+0x49/0xbe
When kzalloc() fails in push_stack(), free_verifier_state() will free
current verifier state. As push_stack() returns, dst_reg was restored
if ptr_is_dst_reg is false. However, as member of the cur_state,
dst_reg is also freed, and error occurs when dereferencing dst_reg.
Simply fix it by testing ret of push_stack() before restoring dst_reg.
Fixes: 979d63d50c0c ("bpf: prevent out of bounds speculation on pointer arithmetic")
Signed-off-by: Xu Yu <xuyu@linux.alibaba.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
mbigen_write_msg clears eventid bits of a mbigen register
when free a interrupt, because msi_domain_deactivate memset
struct msg to zero. Then multiple mbigen pins with zero eventid
will report the same interrupt number.
The eventid clear call trace:
free_irq
__free_irq
irq_shutdown
irq_domain_deactivate_irq
__irq_domain_deactivate_irq
__irq_domain_deactivate_irq
msi_domain_deactivate
platform_msi_write_msg
mbigen_write_msg
Signed-off-by: Jianguo Chen <chenjianguo3@huawei.com>
[maz: massaged subject]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The rising configuration status register (rtsr) is not banked.
As it is shared with the co-processor, it should not be written at probe
time, else the co-processor configuration will be lost.
Fixes: f9fc1745501e ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Falling and rising configuration and status registers are not banked.
As they are shared with M4 co-processor, they should not be cleared
at probe time, else M4 co-processor configuration will be lost.
Fixes: f9fc1745501e ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Document RZ/G2E (R8A774C0) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Fix sparse warning:
drivers/irqchip/irq-mmp.c:182:29: warning:
symbol 'mmp_irq_domain_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Fix sparse warnings:
drivers/irqchip/irq-brcmstb-l2.c:278:12: warning:
symbol 'brcmstb_l2_edge_intc_of_init' was not declared. Should it be static?
drivers/irqchip/irq-brcmstb-l2.c:285:12: warning:
symbol 'brcmstb_l2_lvl_intc_of_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Objtool uses over 512k of stack, thanks to the hash table embedded in
the objtool_file struct. This causes an unnecessarily large stack
allocation and breaks users with low stack limits.
Move the struct off the stack.
Fixes: 042ba73fe7eb ("objtool: Add several performance improvements")
Reported-by: Vassili Karpov <moosotc@gmail.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/df92dcbc4b84b02ffa252f46876df125fb56e2d7.1552954176.git.jpoimboe@redhat.com
|
|
The recent change to prevent use after free and a memory leak introduced an
unconditional call to wq_unregister_lockdep() in the error handling
path. If the lockdep key had not been registered yet, then the lockdep core
emits a warning.
Only call wq_unregister_lockdep() if wq_register_lockdep() has been
called first.
Fixes: 009bb421b6ce ("workqueue, lockdep: Fix an alloc_workqueue() error path")
Reported-by: syzbot+be0c198232f86389c3dd@syzkaller.appspotmail.com
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Qian Cai <cai@lca.pw>
Link: https://lkml.kernel.org/r/20190311230255.176081-1-bvanassche@acm.org
|
|
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Dou Liyang <douliyangs@gmail.com>
Cc: Julien Thierry <julien.thierry@arm.com>
Link: https://lkml.kernel.org/r/20190318065123.11862-1-peterx@redhat.com
|
|
R-Car Gen2 has two different SDHI incarnations in the same chip. The
older one does not support the recently introduced 32 bit register
access to the block count register. Make sure we use this feature only
after the first known version.
Thanks to the Renesas Testing team for this bug report!
Fixes: 5603731a15ef ("mmc: tmio: fix access width of Block Count Register")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Phong Hoang <phong.hoang.wz@renesas.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Setting max_blk_count to 1 here was causing the mmc block layer
to always use the MMC_READ_SINGLE_BLOCK command here, which the
driver does not DMA-accelerate.
Drop the max_blk_ settings here. The mmc host defaults suffice,
along with the max_segs and max_seg_size settings, which I have
now documented in more detail.
Now each MMC command reads 4 512-byte blocks, using DMA instead of
PIO. On my SD card, this increases read performance (measured with dd)
from 167kb/sec to 4.6mb/sec.
Link: http://lkml.kernel.org/r/CAD8Lp47L5T3jnAjBiPs1cQ+yFA3L6LJtgFvMETnBrY63-Zdi2g@mail.gmail.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fixes: c5413ad815a6 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After commit 6d5cd068ee59fba ("mmc: sdhci: use WP GPIO in
sdhci_check_ro()") and commit 39ee32ce486756f ("mmc: sdhci-omap: drop
->get_ro() implementation"), sdhci-omap relied on SDHCI_PRESENT_STATE
to check if the card is read-only, if wp-gpios is not populated
in device tree. However SDHCI_PRESENT_STATE in sdhci-omap does not have
correct read-only state.
sdhci-omap can be used by platforms with both micro SD slot and standard
SD slot with physical write protect pin (using GPIO). Set caps2 to
MMC_CAP2_NO_WRITE_PROTECT based on if wp-gpios property is populated or
not.
This fix is required since existing device-tree node doesn't have
"disable-wp" property and to preserve old-dt compatibility.
Fixes: 6d5cd068ee59fba ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Fixes: 39ee32ce486756f ("mmc: sdhci-omap: drop ->get_ro() implementation")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When I updated the spectre_v2 reporting to handle software count cache
flush I got the logic wrong when there's no software count cache
enabled at all.
The result is that on systems with the software count cache flush
disabled we print:
Mitigation: Indirect branch cache disabled, Software count cache flush
Which correctly indicates that the count cache is disabled, but
incorrectly says the software count cache flush is enabled.
The root of the problem is that we are trying to handle all
combinations of options. But we know now that we only expect to see
the software count cache flush enabled if the other options are false.
So split the two cases, which simplifies the logic and fixes the bug.
We were also missing a space before "(hardware accelerated)".
The result is we see one of:
Mitigation: Indirect branch serialisation (kernel only)
Mitigation: Indirect branch cache disabled
Mitigation: Software count cache flush
Mitigation: Software count cache flush (hardware accelerated)
Fixes: ee13cb249fab ("powerpc/64s: Add support for software count cache flush")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Diana Craciun <diana.craciun@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This reverts commit b189e7589f6d3411e85c6b7ae6eef158f08f388f.
Unable to handle kernel paging request at virtual address c8358000
pgd = efa405c3
[c8358000] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT ARM
CPU: 0 PID: 711 Comm: kworker/0:2 Not tainted 4.20.0+ #30
Hardware name: Freescale i.MX27 (Device Tree Support)
Workqueue: events mxcmci_datawork
PC is at mxcmci_datawork+0xbc/0x2ac
LR is at mxcmci_datawork+0xac/0x2ac
pc : [<c04e33c8>] lr : [<c04e33b8>] psr: 60000013
sp : c6c93f08 ip : 24004180 fp : 00000008
r10: c8358000 r9 : c78b3e24 r8 : c6c92000
r7 : 00000000 r6 : c7bb8680 r5 : c7bb86d4 r4 : c78b3de0
r3 : 00002502 r2 : c090b2e0 r1 : 00000880 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: a68a8000 DAC: 00000055
Process kworker/0:2 (pid: 711, stack limit = 0x389543bc)
Stack: (0xc6c93f08 to 0xc6c94000)
3f00: c7bb86d4 00000000 00000000 c6cbfde0 c7bb86d4 c7ee4200
3f20: 00000000 c0907ea8 00000000 c7bb86d8 c0907ea8 c012077c c6cbfde0 c7bb86d4
3f40: c6cbfde0 c6c92000 c6cbfdf4 c09280ba c0907ea8 c090b2e0 c0907ebc c0120c18
3f60: c6cbfde0 00000000 00000000 c6cbb580 c7ba7c40 c7837edc c6cbb598 00000000
3f80: c6cbfde0 c01208f8 00000000 c01254fc c7ba7c40 c0125400 00000000 00000000
3fa0: 00000000 00000000 00000000 c01010d0 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<c04e33c8>] (mxcmci_datawork) from [<c012077c>] (process_one_work+0x1f0/0x338)
[<c012077c>] (process_one_work) from [<c0120c18>] (worker_thread+0x320/0x474)
[<c0120c18>] (worker_thread) from [<c01254fc>] (kthread+0xfc/0x118)
[<c01254fc>] (kthread) from [<c01010d0>] (ret_from_fork+0x14/0x24)
Exception stack(0xc6c93fb0 to 0xc6c93ff8)
3fa0: 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
Code: e3500000 1a000059 e5153050 e5933038 (e48a3004)
---[ end trace 54ca629b75f0e737 ]---
note: kworker/0:2[711] exited with preempt_count 1
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Fixes: b189e7589f6d ("mmc: mxcmmc: handle highmem pages")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
phydm.internal is allocated using kzalloc which is used multiple
times without a check for NULL pointer. This patch avoids such a
scenario by returning 0, consistent with the failure case.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Colin King reported a bug in read_bbreg_hdl():
memcpy(pcmd->rsp, (u8 *)&val, pcmd->rspsz);
The problem is that "val" is uninitialized.
This code is obviously not useful, but so far as I can tell
"pcmd->cmdcode" is never GEN_CMD_CODE(_Read_BBREG) so it's not harmful
either. For now the easiest fix is to just call r8712_free_cmd_obj()
and return.
Fixes: 2865d42c78a9 ("staging: r8712u: Add the new driver to the mainline kernel")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
skb allocated via dev_alloc_skb can fail and return a NULL pointer.
This patch avoids such a scenario and returns, consistent with other
invocations.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
hwxmits is allocated via kcalloc and not checked for failure before its
dereference. The patch fixes this problem by returning error upstream
in rtl8723bs, rtl8188eu.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Acked-by: Mukesh Ojha <mojha@codeaurora.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some Acer AIO desktops like Veriton Z6860G, Z4860G and Z4660G cannot
record sound from headset MIC. This patch adds the
ALC286_FIXUP_ACER_AIO_HEADSET_MIC quirk to fix this issue.
Fixes: 9f8aefed9623 ("ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4660G")
Fixes: b72f936f6b32 ("ALSA: hda/realtek: Fix mic issue on Acer AIO Veriton Z4860G/Z6860G")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
An munmap() on a binder device causes binder_vma_close() to be called
which clears the alloc->vma pointer.
If direct reclaim causes binder_alloc_free_page() to be called, there
is a race where alloc->vma is read into a local vma pointer and then
used later after the mm->mmap_sem is acquired. This can result in
calling zap_page_range() with an invalid vma which manifests as a
use-after-free in zap_page_range().
The fix is to check alloc->vma after acquiring the mmap_sem (which we
were acquiring anyway) and skip zap_page_range() if it has changed
to NULL.
Signed-off-by: Todd Kjos <tkjos@google.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The selinux-testsuite found an issue resulting in a BUG_ON()
where a conditional relied on a size_t going negative when
checking the validity of a buffer offset.
Fixes: 7a67a39320df ("binder: add function to copy binder object from buffer")
Reported-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch corrects the SPDX License Identifier style
in imx6ull-pinfunc-snvs.h.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
and making some manual changes.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Naresh reported that test_align fails because of the mismatch at the
verbose printout of the register states. The reason is due to the newly
added ref_obj_id.
ref_obj_id is only useful for refcounted reg. Thus, this patch fixes it
by only printing ref_obj_id for refcounted reg. While at it, it also uses
comma instead of space to separate between "id" and "ref_obj_id".
Fixes: 1b986589680a ("bpf: Fix bpf_tcp_sock and bpf_sk_fullsock issue related to bpf_sk_release")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Commit 2b50f7ab6368 ("kbuild: add workaround for Debian make-kpkg")
annoyed people who want to wrap the top Makefile with GNUmakefile
to customize it for their use.
On second thought, we do not need to run the sub-make for in-tree
build with Make 4.x because the 'MAKEFLAGS += -rR' issue only happens
on GNU Make 3.x.
With this commit, people will get back their workflow, and the Debian
make-kpkg will still work.
Fixes: 2b50f7ab6368 ("kbuild: add workaround for Debian make-kpkg")
Reported-by: Andreas Schwab <schwab@suse.de>
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Andreas Schwab <schwab@suse.de>
Tested-by: David Howells <dhowells@redhat.com>
|
|
MIXER on Exynos5 SoCs uses different synchronisation method than Exynos4
to update internal state (shadow registers).
Apparently the driver implements it incorrectly. The rule should be
as follows:
- do not request updating registers until previous request was finished,
ie. MXR_CFG_LAYER_UPDATE_COUNT must be 0.
- before setting registers synchronisation on VSYNC should be turned off,
ie. MXR_STATUS_SYNC_ENABLE should be reset,
- after finishing MXR_STATUS_SYNC_ENABLE should be set again.
The patch hopefully implements it correctly.
Below sample kernel log from page fault caused by the bug:
[ 25.670038] exynos-sysmmu 14650000.sysmmu: 14450000.mixer: PAGE FAULT occurred at 0x2247b800
[ 25.677888] ------------[ cut here ]------------
[ 25.682164] kernel BUG at ../drivers/iommu/exynos-iommu.c:450!
[ 25.687971] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 25.693778] Modules linked in:
[ 25.696816] CPU: 5 PID: 1553 Comm: fb-release_test Not tainted 5.0.0-rc7-01157-g5f86b1566bdd #136
[ 25.705646] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 25.711710] PC is at exynos_sysmmu_irq+0x1c0/0x264
[ 25.716470] LR is at lock_is_held_type+0x44/0x64
v2: added missing MXR_CFG_LAYER_UPDATE bit setting in mixer_enable_sync
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The event pool used for queueing commands is destroyed fairly early in the
ibmvscsi_remove() code path. Since, this happens prior to the call so
scsi_remove_host() it is possible for further calls to queuecommand to be
processed which manifest as a panic due to a NULL pointer dereference as
seen here:
PANIC: "Unable to handle kernel paging request for data at address
0x00000000"
Context process backtrace:
DSISR: 0000000042000000 ????Syscall Result: 0000000000000000
4 [c000000002cb3820] memcpy_power7 at c000000000064204
[Link Register] [c000000002cb3820] ibmvscsi_send_srp_event at d000000003ed14a4
5 [c000000002cb3920] ibmvscsi_send_srp_event at d000000003ed14a4 [ibmvscsi] ?(unreliable)
6 [c000000002cb39c0] ibmvscsi_queuecommand at d000000003ed2388 [ibmvscsi]
7 [c000000002cb3a70] scsi_dispatch_cmd at d00000000395c2d8 [scsi_mod]
8 [c000000002cb3af0] scsi_request_fn at d00000000395ef88 [scsi_mod]
9 [c000000002cb3be0] __blk_run_queue at c000000000429860
10 [c000000002cb3c10] blk_delay_work at c00000000042a0ec
11 [c000000002cb3c40] process_one_work at c0000000000dac30
12 [c000000002cb3cd0] worker_thread at c0000000000db110
13 [c000000002cb3d80] kthread at c0000000000e3378
14 [c000000002cb3e30] ret_from_kernel_thread at c00000000000982c
The kernel buffer log is overfilled with this log:
[11261.952732] ibmvscsi: found no event struct in pool!
This patch reorders the operations during host teardown. Start by calling
the SRP transport and Scsi_Host remove functions to flush any outstanding
work and set the host offline. LLDD teardown follows including destruction
of the event pool, freeing the Command Response Queue (CRQ), and unmapping
any persistent buffers. The event pool destruction is protected by the
scsi_host lock, and the pool is purged prior of any requests for which we
never received a response. Finally, move the removal of the scsi host from
our global list to the end so that the host is easily locatable for
debugging purposes during teardown.
Cc: <stable@vger.kernel.org> # v2.6.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For each ibmvscsi host created during a probe or destroyed during a remove
we either add or remove that host to/from the global ibmvscsi_head
list. This runs the risk of concurrent modification.
This patch adds a simple spinlock around the list modification calls to
prevent concurrent updates as is done similarly in the ibmvfc driver and
ipr driver.
Fixes: 32d6e4b6e4ea ("scsi: ibmvscsi: add vscsi hosts to global list_head")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Make sure we don't try to enqueue XDP_REDIRECT frames to an
inexistent FQ.
While it is guaranteed not to have more than one queue per core,
having fewer queues than CPUs on an interface is a valid
configuration.
Fixes: d678be1dc1ec ("dpaa2-eth: add XDP_REDIRECT support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid that the following warnings are reported when building with W=1:
block/blk-cgroup.c:1755: warning: Function parameter or member 'q' not described in 'blkcg_schedule_throttle'
block/blk-cgroup.c:1755: warning: Function parameter or member 'use_memdelay' not described in 'blkcg_schedule_throttle'
block/blk-cgroup.c:1779: warning: Function parameter or member 'blkg' not described in 'blkcg_add_delay'
block/blk-cgroup.c:1779: warning: Function parameter or member 'now' not described in 'blkcg_add_delay'
block/blk-cgroup.c:1779: warning: Function parameter or member 'delta' not described in 'blkcg_add_delay'
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch avoids that the following warning is reported when building
with W=1:
block/blk-iolatency.c:734:5: warning: no previous prototype for 'blk_iolatency_init' [-Wmissing-prototypes]
Cc: Josef Bacik <jbacik@fb.com>
Fixes: d70675121546 ("block: introduce blk-iolatency io controller") # v4.19
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This function is not used outside the block layer core. Hence unexport it.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
unexpected value
For q->poll_nsec == -1, means doing classic poll, not hybrid poll.
We introduce a new flag BLK_MQ_POLL_CLASSIC to replace -1, which
may make code much easier to read.
Additionally, since val is an int obtained with kstrtoint(), val can be
a negative value other than -1, so return -EINVAL for that case.
Thanks to Damien Le Moal for some good suggestion.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Lukas Wunner says:
====================
ks8851 fixes & cleanups
Four fixes and two cleanups for the Microchip (formerly Micrel) KSZ8851
SPI Ethernet driver.
Some of the fixes might even pass as stable material, but I haven't marked
them as such for cautiousness: Doesn't hurt letting them bake in linux-next
for a few weeks to raise the confidence, even though we've tested them
extensively on our Revolution Pi open source PLCs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 chip is sold either with an SPI interface (KSZ8851SNL) or
with a so-called non-PCI interface (KSZ8851-16MLL). When the driver
for the latter was introduced with commit a55c0a0ed415 ("drivers/net:
ks8851_mll ethernet network driver"), it duplicated the register macros
introduced by the driver for the former with commit 3ba81f3ece3c ("net:
Micrel KS8851 SPI network driver").
The chips are almost identical, so the duplication seems unwarranted.
There are a handful of bits which are in use on the KSZ8851-16MLL but
reserved on the KSZ8851SNL, and vice-versa, but there are no actual
collisions.
Thus, remove the duplicate definitions from the KSZ8851-16MLL driver.
Mark all bits which differ between the two chips. Move the SPI frame
opcodes, which are specific to KSZ8851SNL, to its driver.
The KSZ8851-16MLL driver added a RXFCTR_THRESHOLD_MASK macro which is a
duplication of the RXFCTR_RXFCT_MASK macro, rename it where it's used.
Same for P1MBCR_FORCE_FDX, which duplicates the BMCR_FULLDPLX macro and
OBCR_ODS_16MA, which duplicates OBCR_ODS_16mA.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the header file accompanying the ks8851 driver, the P1SCLMD register
macros are misnamed, they actually pertain to the P1CR register.
The P1CR macros in turn pertain to the P1SR register, see pages 65 to 68
of the spec:
http://www.hqchip.com/uploads/pdf/201703/47c98946d6c97a4766e14db3f24955f2.pdf
The misnomers have no negative consequences so far because the macros
aren't used by ks8851.c, but that's about to change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.
The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.
The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 driver currently requests the IRQ before registering the
net_device. Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present. Most other drivers delay
requesting the IRQ until the net_device is opened. Do the same.
The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 73fdeb82e963 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.
However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").
However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management: On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.
The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.
Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.
The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In symbol__disassemble(), DSO_BINARY_TYPE__BPF_PROG_INFO dso calls into
a new function symbol__disassemble_bpf(), where annotation line
information is filled based on the bpf_prog_info and btf data saved in
given perf_env.
symbol__disassemble_bpf() uses binutils's libopcodes to disassemble bpf
programs.
Committer testing:
After fixing this:
- u64 *addrs = (u64 *)(info_linear->info.jited_ksyms);
+ u64 *addrs = (u64 *)(uintptr_t)(info_linear->info.jited_ksyms);
Detected when crossbuilding to a 32-bit arch.
And making all this dependent on HAVE_LIBBFD_SUPPORT and
HAVE_LIBBPF_SUPPORT:
1) Have a BPF program running, one that has BTF info, etc, I used
the tools/perf/examples/bpf/augmented_raw_syscalls.c put in place
by 'perf trace'.
# grep -B1 augmented_raw ~/.perfconfig
[trace]
add_events = /home/acme/git/perf/tools/perf/examples/bpf/augmented_raw_syscalls.c
#
# perf trace -e *mmsg
dnf/6245 sendmmsg(20, 0x7f5485a88030, 2, MSG_NOSIGNAL) = 2
NetworkManager/10055 sendmmsg(22<socket:[1056822]>, 0x7f8126ad1bb0, 2, MSG_NOSIGNAL) = 2
2) Then do a 'perf record' system wide for a while:
# perf record -a
^C[ perf record: Woken up 68 times to write data ]
[ perf record: Captured and wrote 19.427 MB perf.data (366891 samples) ]
#
3) Check that we captured BPF and BTF info in the perf.data file:
# perf report --header-only | grep 'b[pt]f'
# event : name = cycles:ppp, , id = { 294789, 294790, 294791, 294792, 294793, 294794, 294795, 294796 }, size = 112, { sample_period, sample_freq } = 4000, sample_type = IP|TID|TIME|CPU|PERIOD, read_format = ID, disabled = 1, inherit = 1, mmap = 1, comm = 1, freq = 1, task = 1, precise_ip = 3, sample_id_all = 1, exclude_guest = 1, mmap2 = 1, comm_exec = 1, ksymbol = 1, bpf_event = 1
# bpf_prog_info of id 13
# bpf_prog_info of id 14
# bpf_prog_info of id 15
# bpf_prog_info of id 16
# bpf_prog_info of id 17
# bpf_prog_info of id 18
# bpf_prog_info of id 21
# bpf_prog_info of id 22
# bpf_prog_info of id 41
# bpf_prog_info of id 42
# btf info of id 2
#
4) Check which programs got recorded:
# perf report | grep bpf_prog | head
0.16% exe bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.14% exe bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
0.08% fuse-overlayfs bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.07% fuse-overlayfs bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
0.01% clang-4.0 bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
0.01% clang-4.0 bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.00% clang bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
0.00% runc bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.00% clang bpf_prog_819967866022f1e1_sys_enter [k] bpf_prog_819967866022f1e1_sys_enter
0.00% sh bpf_prog_c1bd85c092d6e4aa_sys_exit [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
#
This was with the default --sort order for 'perf report', which is:
--sort comm,dso,symbol
If we just look for the symbol, for instance:
# perf report --sort symbol | grep bpf_prog | head
0.26% [k] bpf_prog_819967866022f1e1_sys_enter - -
0.24% [k] bpf_prog_c1bd85c092d6e4aa_sys_exit - -
#
or the DSO:
# perf report --sort dso | grep bpf_prog | head
0.26% bpf_prog_819967866022f1e1_sys_enter
0.24% bpf_prog_c1bd85c092d6e4aa_sys_exit
#
We'll see the two BPF programs that augmented_raw_syscalls.o puts in
place, one attached to the raw_syscalls:sys_enter and another to the
raw_syscalls:sys_exit tracepoints, as expected.
Now we can finally do, from the command line, annotation for one of
those two symbols, with the original BPF program source coude intermixed
with the disassembled JITed code:
# perf annotate --stdio2 bpf_prog_819967866022f1e1_sys_enter
Samples: 950 of event 'cycles:ppp', 4000 Hz, Event count (approx.): 553756947, [percent: local period]
bpf_prog_819967866022f1e1_sys_enter() bpf_prog_819967866022f1e1_sys_enter
Percent int sys_enter(struct syscall_enter_args *args)
53.41 push %rbp
0.63 mov %rsp,%rbp
0.31 sub $0x170,%rsp
1.93 sub $0x28,%rbp
7.02 mov %rbx,0x0(%rbp)
3.20 mov %r13,0x8(%rbp)
1.07 mov %r14,0x10(%rbp)
0.61 mov %r15,0x18(%rbp)
0.11 xor %eax,%eax
1.29 mov %rax,0x20(%rbp)
0.11 mov %rdi,%rbx
return bpf_get_current_pid_tgid();
2.02 → callq *ffffffffda6776d9
2.76 mov %eax,-0x148(%rbp)
mov %rbp,%rsi
int sys_enter(struct syscall_enter_args *args)
add $0xfffffffffffffeb8,%rsi
return bpf_map_lookup_elem(pids, &pid) != NULL;
movabs $0xffff975ac2607800,%rdi
1.26 → callq *ffffffffda6789e9
cmp $0x0,%rax
2.43 → je 0
add $0x38,%rax
0.21 xor %r13d,%r13d
if (pid_filter__has(&pids_filtered, getpid()))
0.81 cmp $0x0,%rax
→ jne 0
mov %rbp,%rdi
probe_read(&augmented_args.args, sizeof(augmented_args.args), args);
2.22 add $0xfffffffffffffeb8,%rdi
0.11 mov $0x40,%esi
0.32 mov %rbx,%rdx
2.74 → callq *ffffffffda658409
syscall = bpf_map_lookup_elem(&syscalls, &augmented_args.args.syscall_nr);
0.22 mov %rbp,%rsi
1.69 add $0xfffffffffffffec0,%rsi
syscall = bpf_map_lookup_elem(&syscalls, &augmented_args.args.syscall_nr);
movabs $0xffff975bfcd36000,%rdi
add $0xd0,%rdi
0.21 mov 0x0(%rsi),%eax
0.93 cmp $0x200,%rax
→ jae 0
0.10 shl $0x3,%rax
0.11 add %rdi,%rax
0.11 → jmp 0
xor %eax,%eax
if (syscall == NULL || !syscall->enabled)
1.07 cmp $0x0,%rax
→ je 0
if (syscall == NULL || !syscall->enabled)
6.57 movzbq 0x0(%rax),%rdi
if (syscall == NULL || !syscall->enabled)
cmp $0x0,%rdi
0.95 → je 0
mov $0x40,%r8d
switch (augmented_args.args.syscall_nr) {
mov -0x140(%rbp),%rdi
switch (augmented_args.args.syscall_nr) {
cmp $0x2,%rdi
→ je 0
cmp $0x101,%rdi
→ je 0
cmp $0x15,%rdi
→ jne 0
case SYS_OPEN: filename_arg = (const void *)args->args[0];
mov 0x10(%rbx),%rdx
→ jmp 0
case SYS_OPENAT: filename_arg = (const void *)args->args[1];
mov 0x18(%rbx),%rdx
if (filename_arg != NULL) {
cmp $0x0,%rdx
→ je 0
xor %edi,%edi
augmented_args.filename.reserved = 0;
mov %edi,-0x104(%rbp)
augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
mov %rbp,%rdi
add $0xffffffffffffff00,%rdi
augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
mov $0x100,%esi
→ callq *ffffffffda658499
mov $0x148,%r8d
augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
mov %eax,-0x108(%rbp)
augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
mov %rax,%rdi
shl $0x20,%rdi
shr $0x20,%rdi
if (augmented_args.filename.size < sizeof(augmented_args.filename.value)) {
cmp $0xff,%rdi
→ ja 0
len -= sizeof(augmented_args.filename.value) - augmented_args.filename.size;
add $0x48,%rax
len &= sizeof(augmented_args.filename.value) - 1;
and $0xff,%rax
mov %rax,%r8
mov %rbp,%rcx
return perf_event_output(args, &__augmented_syscalls__, BPF_F_CURRENT_CPU, &augmented_args, len);
add $0xfffffffffffffeb8,%rcx
mov %rbx,%rdi
movabs $0xffff975fbd72d800,%rsi
mov $0xffffffff,%edx
→ callq *ffffffffda658ad9
mov %rax,%r13
}
mov %r13,%rax
0.72 mov 0x0(%rbp),%rbx
mov 0x8(%rbp),%r13
1.16 mov 0x10(%rbp),%r14
0.10 mov 0x18(%rbp),%r15
0.42 add $0x28,%rbp
0.54 leaveq
0.54 ← retq
#
Please see 'man perf-config' to see how to control what should be seen,
via ~/.perfconfig [annotate] section, for instance, one can suppress the
source code and see just the disassembly, etc.
Alternatively, use the TUI bu just using 'perf annotate', press
'/bpf_prog' to see the bpf symbols, press enter and do the interactive
annotation, which allows for dumping to a file after selecting the
the various output tunables, for instance, the above without source code
intermixed, plus showing all the instruction offsets:
# perf annotate bpf_prog_819967866022f1e1_sys_enter
Then press: 's' to hide the source code + 'O' twice to show all
instruction offsets, then 'P' to print to the
bpf_prog_819967866022f1e1_sys_enter.annotation file, which will have:
# cat bpf_prog_819967866022f1e1_sys_enter.annotation
bpf_prog_819967866022f1e1_sys_enter() bpf_prog_819967866022f1e1_sys_enter
Event: cycles:ppp
53.41 0: push %rbp
0.63 1: mov %rsp,%rbp
0.31 4: sub $0x170,%rsp
1.93 b: sub $0x28,%rbp
7.02 f: mov %rbx,0x0(%rbp)
3.20 13: mov %r13,0x8(%rbp)
1.07 17: mov %r14,0x10(%rbp)
0.61 1b: mov %r15,0x18(%rbp)
0.11 1f: xor %eax,%eax
1.29 21: mov %rax,0x20(%rbp)
0.11 25: mov %rdi,%rbx
2.02 28: → callq *ffffffffda6776d9
2.76 2d: mov %eax,-0x148(%rbp)
33: mov %rbp,%rsi
36: add $0xfffffffffffffeb8,%rsi
3d: movabs $0xffff975ac2607800,%rdi
1.26 47: → callq *ffffffffda6789e9
4c: cmp $0x0,%rax
2.43 50: → je 0
52: add $0x38,%rax
0.21 56: xor %r13d,%r13d
0.81 59: cmp $0x0,%rax
5d: → jne 0
63: mov %rbp,%rdi
2.22 66: add $0xfffffffffffffeb8,%rdi
0.11 6d: mov $0x40,%esi
0.32 72: mov %rbx,%rdx
2.74 75: → callq *ffffffffda658409
0.22 7a: mov %rbp,%rsi
1.69 7d: add $0xfffffffffffffec0,%rsi
84: movabs $0xffff975bfcd36000,%rdi
8e: add $0xd0,%rdi
0.21 95: mov 0x0(%rsi),%eax
0.93 98: cmp $0x200,%rax
9f: → jae 0
0.10 a1: shl $0x3,%rax
0.11 a5: add %rdi,%rax
0.11 a8: → jmp 0
aa: xor %eax,%eax
1.07 ac: cmp $0x0,%rax
b0: → je 0
6.57 b6: movzbq 0x0(%rax),%rdi
bb: cmp $0x0,%rdi
0.95 bf: → je 0
c5: mov $0x40,%r8d
cb: mov -0x140(%rbp),%rdi
d2: cmp $0x2,%rdi
d6: → je 0
d8: cmp $0x101,%rdi
df: → je 0
e1: cmp $0x15,%rdi
e5: → jne 0
e7: mov 0x10(%rbx),%rdx
eb: → jmp 0
ed: mov 0x18(%rbx),%rdx
f1: cmp $0x0,%rdx
f5: → je 0
f7: xor %edi,%edi
f9: mov %edi,-0x104(%rbp)
ff: mov %rbp,%rdi
102: add $0xffffffffffffff00,%rdi
109: mov $0x100,%esi
10e: → callq *ffffffffda658499
113: mov $0x148,%r8d
119: mov %eax,-0x108(%rbp)
11f: mov %rax,%rdi
122: shl $0x20,%rdi
126: shr $0x20,%rdi
12a: cmp $0xff,%rdi
131: → ja 0
133: add $0x48,%rax
137: and $0xff,%rax
13d: mov %rax,%r8
140: mov %rbp,%rcx
143: add $0xfffffffffffffeb8,%rcx
14a: mov %rbx,%rdi
14d: movabs $0xffff975fbd72d800,%rsi
157: mov $0xffffffff,%edx
15c: → callq *ffffffffda658ad9
161: mov %rax,%r13
164: mov %r13,%rax
0.72 167: mov 0x0(%rbp),%rbx
16b: mov 0x8(%rbp),%r13
1.16 16f: mov 0x10(%rbp),%r14
0.10 173: mov 0x18(%rbp),%r15
0.42 177: add $0x28,%rbp
0.54 17b: leaveq
0.54 17c: ← retq
Another cool way to test all this is to symple use 'perf top' look for
those symbols, go there and press enter, annotate it live :-)
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-13-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Commit 003ca0fd2286 ("Refactor disassembler selection") in the binutils
repo, which changed the disassembler() function signature, so we must
use the feature test introduced in fb982666e380 ("tools/bpftool: fix
bpftool build with bintutils >= 2.9") to deal with that.
Committer testing:
After adding the missing function call to test-all.c, and:
FEATURE_CHECK_LDFLAGS-disassembler-four-args = -bfd -lopcodes
And the fallbacks for cases where we need -liberty and sometimes -lz to
tools/perf/Makefile.config, we get:
$ make -C tools/perf O=/tmp/build/perf install-bin
make: Entering directory '/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j8' parallel build
Auto-detecting system features:
... dwarf: [ on ]
... dwarf_getlocations: [ on ]
... glibc: [ on ]
... gtk2: [ on ]
... libaudit: [ on ]
... libbfd: [ on ]
... libelf: [ on ]
... libnuma: [ on ]
... numa_num_possible_cpus: [ on ]
... libperl: [ on ]
... libpython: [ on ]
... libslang: [ on ]
... libcrypto: [ on ]
... libunwind: [ on ]
... libdw-dwarf-unwind: [ on ]
... zlib: [ on ]
... lzma: [ on ]
... get_cpuid: [ on ]
... bpf: [ on ]
... libaio: [ on ]
... disassembler-four-args: [ on ]
CC /tmp/build/perf/jvmti/libjvmti.o
CC /tmp/build/perf/builtin-bench.o
<SNIP>
$
$
The feature detection test-all.bin gets successfully built and linked:
$ ls -la /tmp/build/perf/feature/test-all.bin
-rwxrwxr-x. 1 acme acme 2680352 Mar 19 11:07 /tmp/build/perf/feature/test-all.bin
$ nm /tmp/build/perf/feature/test-all.bin | grep -w disassembler
0000000000061f90 T disassembler
$
Time to move on to the patches that make use of this disassembler()
routine in binutils's libopcodes.
Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-13-songliubraving@fb.com
[ split from a larger patch, added missing FEATURE_CHECK_LDFLAGS-disassembler-four-args ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Back in commit a89ca6f24ffe4 ("Btrfs: fix fsync after truncate when
no_holes feature is enabled") I added an assertion that is triggered when
an inline extent is found to assert that the length of the (uncompressed)
data the extent represents is the same as the i_size of the inode, since
that is true most of the time I couldn't find or didn't remembered about
any exception at that time. Later on the assertion was expanded twice to
deal with a case of a compressed inline extent representing a range that
matches the sector size followed by an expanding truncate, and another
case where fallocate can update the i_size of the inode without adding
or updating existing extents (if the fallocate range falls entirely within
the first block of the file). These two expansion/fixes of the assertion
were done by commit 7ed586d0a8241 ("Btrfs: fix assertion on fsync of
regular file when using no-holes feature") and commit 6399fb5a0b69a
("Btrfs: fix assertion failure during fsync in no-holes mode").
These however missed the case where an falloc expands the i_size of an
inode to exactly the sector size and inline extent exists, for example:
$ mkfs.btrfs -f -O no-holes /dev/sdc
$ mount /dev/sdc /mnt
$ xfs_io -f -c "pwrite -S 0xab 0 1096" /mnt/foobar
wrote 1096/1096 bytes at offset 0
1 KiB, 1 ops; 0.0002 sec (4.448 MiB/sec and 4255.3191 ops/sec)
$ xfs_io -c "falloc 1096 3000" /mnt/foobar
$ xfs_io -c "fsync" /mnt/foobar
Segmentation fault
$ dmesg
[701253.602385] assertion failed: len == i_size || (len == fs_info->sectorsize && btrfs_file_extent_compression(leaf, extent) != BTRFS_COMPRESS_NONE) || (len < i_size && i_size < fs_info->sectorsize), file: fs/btrfs/tree-log.c, line: 4727
[701253.602962] ------------[ cut here ]------------
[701253.603224] kernel BUG at fs/btrfs/ctree.h:3533!
[701253.603503] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[701253.603774] CPU: 2 PID: 7192 Comm: xfs_io Tainted: G W 5.0.0-rc8-btrfs-next-45 #1
[701253.604054] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014
[701253.604650] RIP: 0010:assfail.constprop.23+0x18/0x1a [btrfs]
(...)
[701253.605591] RSP: 0018:ffffbb48c186bc48 EFLAGS: 00010286
[701253.605914] RAX: 00000000000000de RBX: ffff921d0a7afc08 RCX: 0000000000000000
[701253.606244] RDX: 0000000000000000 RSI: ffff921d36b16868 RDI: ffff921d36b16868
[701253.606580] RBP: ffffbb48c186bcf0 R08: 0000000000000000 R09: 0000000000000000
[701253.606913] R10: 0000000000000003 R11: 0000000000000000 R12: ffff921d05d2de18
[701253.607247] R13: ffff921d03b54000 R14: 0000000000000448 R15: ffff921d059ecf80
[701253.607769] FS: 00007f14da906700(0000) GS:ffff921d36b00000(0000) knlGS:0000000000000000
[701253.608163] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[701253.608516] CR2: 000056087ea9f278 CR3: 00000002268e8001 CR4: 00000000003606e0
[701253.608880] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[701253.609250] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[701253.609608] Call Trace:
[701253.609994] btrfs_log_inode+0xdfb/0xe40 [btrfs]
[701253.610383] btrfs_log_inode_parent+0x2be/0xa60 [btrfs]
[701253.610770] ? do_raw_spin_unlock+0x49/0xc0
[701253.611150] btrfs_log_dentry_safe+0x4a/0x70 [btrfs]
[701253.611537] btrfs_sync_file+0x3b2/0x440 [btrfs]
[701253.612010] ? do_sysinfo+0xb0/0xf0
[701253.612552] do_fsync+0x38/0x60
[701253.612988] __x64_sys_fsync+0x10/0x20
[701253.613360] do_syscall_64+0x60/0x1b0
[701253.613733] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[701253.614103] RIP: 0033:0x7f14da4e66d0
(...)
[701253.615250] RSP: 002b:00007fffa670fdb8 EFLAGS: 00000246 ORIG_RAX: 000000000000004a
[701253.615647] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f14da4e66d0
[701253.616047] RDX: 000056087ea9c260 RSI: 000056087ea9c260 RDI: 0000000000000003
[701253.616450] RBP: 0000000000000001 R08: 0000000000000020 R09: 0000000000000010
[701253.616854] R10: 000000000000009b R11: 0000000000000246 R12: 000056087ea9c260
[701253.617257] R13: 000056087ea9c240 R14: 0000000000000000 R15: 000056087ea9dd10
(...)
[701253.619941] ---[ end trace e088d74f132b6da5 ]---
Updating the assertion again to allow for this particular case would result
in a meaningless assertion, plus there is currently no risk of logging
content that would result in any corruption after a log replay if the size
of the data encoded in an inline extent is greater than the inode's i_size
(which is not currently possibe either with or without compression),
therefore just remove the assertion.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We found out that for v2 hw, a SATA disk can not be written to after the
system comes up.
In commit ffb1c820b8b6 ("scsi: hisi_sas: remove the check of sas_dev status
in hisi_sas_I_T_nexus_reset()"), we introduced a path where we may issue an
internal abort for a SATA device, but without following it with a
softreset.
We need to always follow an internal abort with a software reset, as per HW
programming flow, so add this.
Fixes: ffb1c820b8b6 ("scsi: hisi_sas: remove the check of sas_dev status in hisi_sas_I_T_nexus_reset()")
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The lpi_range_list is supposed to be sorted in ascending order of
->base_id (at least if the range merging is to work), but the current
comparison function returns a positive value if rb->base_id >
ra->base_id, which means that list_sort() will put A after B in that
case - and vice versa, of course.
Fixes: 880cb3cddd16 (irqchip/gic-v3-its: Refactor LPI allocator)
Cc: stable@vger.kernel.org (v4.19+)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
In sctp_setsockopt_bindx()/__sctp_setsockopt_connectx(), it allocates
memory with addrs_size which is passed from userspace. We used flag
GFP_USER to put some more restrictions on it in Commit cacc06215271
("sctp: use GFP_USER for user-controlled kmalloc").
However, since Commit c981f254cc82 ("sctp: use vmemdup_user() rather
than badly open-coding memdup_user()"), vmemdup_user() has been used,
which doesn't check GFP_USER flag when goes to vmalloc_*(). So when
addrs_size is a huge value, it could exhaust memory and even trigger
oom killer.
This patch is to use memdup_user() instead, in which GFP_USER would
work to limit the memory allocation with a huge addrs_size.
Note we can't fix it by limiting 'addrs_size', as there's no demand
for it from RFC.
Reported-by: syzbot+ec1b7575afef85a0e5ca@syzkaller.appspotmail.com
Fixes: c981f254cc82 ("sctp: use vmemdup_user() rather than badly open-coding memdup_user()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jianlin reported a crash:
[ 381.484332] BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
[ 381.619802] RIP: 0010:fib6_rule_lookup+0xa3/0x160
[ 382.009615] Call Trace:
[ 382.020762] <IRQ>
[ 382.030174] ip6_route_redirect.isra.52+0xc9/0xf0
[ 382.050984] ip6_redirect+0xb6/0xf0
[ 382.066731] icmpv6_notify+0xca/0x190
[ 382.083185] ndisc_redirect_rcv+0x10f/0x160
[ 382.102569] ndisc_rcv+0xfb/0x100
[ 382.117725] icmpv6_rcv+0x3f2/0x520
[ 382.133637] ip6_input_finish+0xbf/0x460
[ 382.151634] ip6_input+0x3b/0xb0
[ 382.166097] ipv6_rcv+0x378/0x4e0
It was caused by the lookup function __ip6_route_redirect() returns NULL in
fib6_rule_lookup() when ip6_create_rt_rcu() returns NULL.
So we fix it by simply making ip6_create_rt_rcu() return ip6_null_entry
instead of NULL.
v1->v2:
- move down 'fallback:' to make it more readable.
Fixes: e873e4b9cc7e ("ipv6: use fib6_info_hold_safe() when necessary")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- unaligned access support for HS cores
- Removed extra memory barrier around spinlock code
- HSDK platform updates: enable dmac, reset
- some more boot logging updates
- misc minor fixes
* tag 'arc-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arch: arc: Kconfig: pedantic formatting
ARCv2: spinlock: remove the extra smp_mb before lock, after unlock
ARC: unaligned: relax the check for gcc supporting -mno-unaligned-access
ARC: boot log: cut down on verbosity
ARCv2: boot log: refurbish HS core/release identification
arc: hsdk_defconfig: Enable CONFIG_BLK_DEV_RAM
ARC: u-boot args: check that magic number is correct
ARC: perf: bpok condition only exists for ARCompact
ARCv2: Add explcit unaligned access support (and ability to disable too)
ARCv2: lib: introduce memcpy optimized for unaligned access
ARC: [plat-hsdk]: Enable AXI DW DMAC support
ARC: [plat-hsdk]: Add reset controller handle to manage USB reset
ARC: DTB: [scripted] fix node name and address spelling
|
