| Age | Commit message (Collapse) | Author |
|---|
|
This was formerly used to store the tclk value. This is now discovered
using the clk API, rather than pass it as platform data.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
We are currently using an inferior or equal operator for comparing
the transfer frequency with the clock frequency table. Because of
this, we always end up selecting 20Mhz as a frequency, due to the
inequality transfer hz <= 20 Mhz being always true. Fix this by
reversing the inequality, which is how the comparison should be done.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Additional updates for 3.6
A few more fixes for 3.6, some of which are relatively important -
they've all been in -next for at least some time.
- DAPM fixes for the recent locking changes.
- Fix for _PRE and _POST widgets (which have been broken for a few
releases now).
- A couple of minor driver updates.
|
|
Convert orion_wdt driver to use watchdog framework API.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
module_platform_driver() replaces module_init() and module_exit()
and makes the code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Some motherboards like the Advantech ARK3400 documentation
use a non-inverted GPIO pin. We fix this by assuming that
the BIOS will set the Polarity bit for the GPIO correctly
at startup and we keep the Bit-setting intact when we start
and stop the watchdog.
Reported-by: Jean-François Deverge <jf.deverge@gmail.com>
Signed-off-by: Dave Mueller <d.mueller@elsoft.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
intransition state.
OMAP watchdog driver is adapted to runtime PM like a general device
driver but it is not appropriate. It is causing couple of functional
issues.
1. On OMAP4 SYSCLK can't be gated, because of issue with WDTIMER2 module,
which constantly stays in "in transition" state. Value of register
CM_WKUP_WDTIMER2_CLKCTRL is always 0x00010000 in this case.
Issue occurs immediately after first idle, when hwmod framework tries
to disable WDTIMER2 functional clock - "wd_timer2_fck". After this
module falls to "in transition" state, and SYSCLK gating is blocked.
2. Due to runtime PM, watchdog timer may be completely disabled.
In current code base watchdog timer is not disabled only because of
issue 1. Otherwise state of WDTIMER2 module will be "Disabled", and there
will be no interrupts from omap_wdt. In other words watchdog will not
work at all.
Watchdong is a special IP and it should not be disabled otherwise
purpose of it itself is defeated. Watchdog functional clock should
never be disabled. This patch updates the runtime PM handling in
driver so that runtime PM is limited only during probe/shutdown
and suspend/resume.
The patch fixes issue 1 and 2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
ie6xx_wdt_probe() calls ie6xx_wdt_debugfs_exit() as part of
it's error cleanup path, and ie6xx_wdt_debugfs_exit() is
currently annotated __devexit.
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
bcm63xx_wdt was used as a platform_driver but was not suffixed with
_driver, thus causing section mismatches, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch converts the iTCO_wdt watchdog driver to use the
generic watchdog framework.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This watchdog driver had ioctl defines introduced locally
for pre timeout handling, marked to be removed as soon as
a generic replacement would become available.
The latter has actually occurred in 2006, at e05b59fe.
Remove the local duplicates for pre timeout handling.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Do not use clock-frequency property from parent node.
Use it from watchdog node.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-By: Alejandro Cabrera <acabrera@udio.cujae.edu.cu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Make sure we prepare/unprepare the COH901327 watchdog timer
as is required by the clk API especially if you use common
clock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by : Pankaj Jangra <jangra.pankaj9@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The Jetway JNF99 motherboard features a F71869 SuperIO chip, but its
watchdog chipset ID appears to be 1007 (as opposed to 0814). Some testing
confirmed it behaves the exact same as 0814. So add this chipset ID to the
module's ID list so that the Fintek watchdog driver can correctly identify
and access it.
Signed-off-by: Justin Wheeler <jwheeler@datademons.com>
Acked-by: Giel van Schijndel <me@mortis.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
'api/domain-attr' into next
Conflicts:
drivers/iommu/iommu.c
include/linux/iommu.h
|
|
Add Asus All-In-One PC keyboard model AK1D.
BugLink: https://bugs.launchpad.net/bugs/1027789
Signed-off-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
Ever since the DAPM performance improvements we've been marking all widgets
as not dirty after each DAPM run. Since _PRE and _POST events aren't part
of the DAPM graph this has rendered them non-functional, they will never be
marked dirty again and thus will never be run again.
Fix this by skipping them when marking widgets as not dirty.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@vger.kernel.org
|
|
Jay Fenlason (fenlason@redhat.com) found a bug,
that recvfrom() on an RDS socket can return the contents of random kernel
memory to userspace if it was called with a address length larger than
sizeof(struct sockaddr_in).
rds_recvmsg() also fails to set the addr_len paramater properly before
returning, but that's just a bug.
There are also a number of cases wher recvfrom() can return an entirely bogus
address. Anything in rds_recvmsg() that returns a non-negative value but does
not go through the "sin = (struct sockaddr_in *)msg->msg_name;" code path
at the end of the while(1) loop will return up to 128 bytes of kernel memory
to userspace.
And I write two test programs to reproduce this bug, you will see that in
rds_server, fromAddr will be overwritten and the following sock_fd will be
destroyed.
Yes, it is the programmer's fault to set msg_namelen incorrectly, but it is
better to make the kernel copy the real length of address to user space in
such case.
How to run the test programs ?
I test them on 32bit x86 system, 3.5.0-rc7.
1 compile
gcc -o rds_client rds_client.c
gcc -o rds_server rds_server.c
2 run ./rds_server on one console
3 run ./rds_client on another console
4 you will see something like:
server is waiting to receive data...
old socket fd=3
server received data from client:data from client
msg.msg_namelen=32
new socket fd=-1067277685
sendmsg()
: Bad file descriptor
/***************** rds_client.c ********************/
int main(void)
{
int sock_fd;
struct sockaddr_in serverAddr;
struct sockaddr_in toAddr;
char recvBuffer[128] = "data from client";
struct msghdr msg;
struct iovec iov;
sock_fd = socket(AF_RDS, SOCK_SEQPACKET, 0);
if (sock_fd < 0) {
perror("create socket error\n");
exit(1);
}
memset(&serverAddr, 0, sizeof(serverAddr));
serverAddr.sin_family = AF_INET;
serverAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
serverAddr.sin_port = htons(4001);
if (bind(sock_fd, (struct sockaddr*)&serverAddr, sizeof(serverAddr)) < 0) {
perror("bind() error\n");
close(sock_fd);
exit(1);
}
memset(&toAddr, 0, sizeof(toAddr));
toAddr.sin_family = AF_INET;
toAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
toAddr.sin_port = htons(4000);
msg.msg_name = &toAddr;
msg.msg_namelen = sizeof(toAddr);
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = strlen(recvBuffer) + 1;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendto() error\n");
close(sock_fd);
exit(1);
}
printf("client send data:%s\n", recvBuffer);
memset(recvBuffer, '\0', 128);
msg.msg_name = &toAddr;
msg.msg_namelen = sizeof(toAddr);
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("receive data from server:%s\n", recvBuffer);
close(sock_fd);
return 0;
}
/***************** rds_server.c ********************/
int main(void)
{
struct sockaddr_in fromAddr;
int sock_fd;
struct sockaddr_in serverAddr;
unsigned int addrLen;
char recvBuffer[128];
struct msghdr msg;
struct iovec iov;
sock_fd = socket(AF_RDS, SOCK_SEQPACKET, 0);
if(sock_fd < 0) {
perror("create socket error\n");
exit(0);
}
memset(&serverAddr, 0, sizeof(serverAddr));
serverAddr.sin_family = AF_INET;
serverAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
serverAddr.sin_port = htons(4000);
if (bind(sock_fd, (struct sockaddr*)&serverAddr, sizeof(serverAddr)) < 0) {
perror("bind error\n");
close(sock_fd);
exit(1);
}
printf("server is waiting to receive data...\n");
msg.msg_name = &fromAddr;
/*
* I add 16 to sizeof(fromAddr), ie 32,
* and pay attention to the definition of fromAddr,
* recvmsg() will overwrite sock_fd,
* since kernel will copy 32 bytes to userspace.
*
* If you just use sizeof(fromAddr), it works fine.
* */
msg.msg_namelen = sizeof(fromAddr) + 16;
/* msg.msg_namelen = sizeof(fromAddr); */
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
while (1) {
printf("old socket fd=%d\n", sock_fd);
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("server received data from client:%s\n", recvBuffer);
printf("msg.msg_namelen=%d\n", msg.msg_namelen);
printf("new socket fd=%d\n", sock_fd);
strcat(recvBuffer, "--data from server");
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendmsg()\n");
close(sock_fd);
exit(1);
}
}
close(sock_fd);
return 0;
}
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there is no OVS_SAMPLE_ATTR_ACTIONS set then "acts_list" is NULL and
it leads to a NULL dereference when we call nla_len(acts_list). This
is a static checker fix, not something I have seen in testing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ICMP messages generated in output path if frame length is bigger than
mtu are actually lost because socket is owned by user (doing the xmit)
One example is the ipgre_tunnel_xmit() calling
icmp_send(skb, ICMP_DEST_UNREACH, ICMP_FRAG_NEEDED, htonl(mtu));
We had a similar case fixed in commit a34a101e1e6 (ipv6: disable GSO on
sockets hitting dst_allfrag).
Problem of such fix is that it relied on retransmit timers, so short tcp
sessions paid a too big latency increase price.
This patch uses the tcp_release_cb() infrastructure so that MTU
reduction messages (ICMP messages) are not lost, and no extra delay
is added in TCP transmits.
Reported-by: Maciej Żenczykowski <maze@google.com>
Diagnosed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 57840 boards come in two flavours: 2 x 20G and 4 x 10G.
To better differentiate between the two flavours, a separate device ID
was assigned to each.
The silicon default value is still the currently supported 57840 device ID
(0x168d), and since a user can damage the nvram (e.g., 'ethtool -E')
the driver will still support this device ID to allow the user to amend the
nvram back into a supported configuration.
Notice this patch contains lines longer than 80 characters (strings).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In tcp_tw_remember_stamp we incorrectly checked tw
instead of tm, it can lead to oops if the cached entry is
not found.
tcpm_stamp was not updated in tcpm_check_stamp when
tcpm_suck_dst was called, move the update into tcpm_suck_dst,
so that we do not call it infinitely on every next cache hit
after TCP_METRICS_TIMEOUT.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
return value
Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return
value to be consistent with the rest of the checks after niu_rbr_add_page()
calls in this file.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix Neptune ethernet driver to check dma mapping error after map_page()
interface returns.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ocrdma' and 'qib' into for-linus
|
|
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
|
|
All callers of kmap_atomic_primary() use __KM_CACHE, so it can be
removed safely, and __kmap_atomic_primary() only check if 'type' if
__KM_CACHE or not, so 'type' can be changed to a boolean as well.
Ditto for kunmap_atomic_primary()/__kunmap_atomic_primary().
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Cong Wang <amwang@redhat.com>
|
|
Signed-off-by: Cong Wang <amwang@redhat.com>
|
|
The current mpic code creates a linear revmap just big enough for all
the sources, which happens to miss the IPIs and timers on some machines.
This will in turn break when the irqdomain code loses the fallback of
doing a linear search when the revmap fails (and really slows down IPIs
otherwise).
This happens for example on the U4 based Apple machines such as the
dual core PowerMac G5s.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The function ext4_calc_metadata_amount() has side effects, although
it's not obvious from its function name. So if we fail to claim
space, regardless of whether we retry to claim the space again, or
return an error, we need to undo these side effects.
Otherwise we can end up incorrectly calculating the number of metadata
blocks needed for the operation, which was responsible for an xfstests
failure for test #271 when using an ext2 file system with delalloc
enabled.
Reported-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
If we hit a condition where we have allocated metadata blocks that
were not appropriately reserved, we risk underflow of
ei->i_reserved_meta_blocks. In turn, this can throw
sbi->s_dirtyclusters_counter significantly out of whack and undermine
the nondelalloc fallback logic in ext4_nonda_switch(). Warn if this
occurs and set i_allocated_meta_blocks to avoid this problem.
This condition is reproduced by xfstests 270 against ext2 with
delalloc enabled:
Mar 28 08:58:02 localhost kernel: [ 171.526344] EXT4-fs (loop1): delayed block allocation failed for inode 14 at logical offset 64486 with max blocks 64 with error -28
Mar 28 08:58:02 localhost kernel: [ 171.526346] EXT4-fs (loop1): This should not happen!! Data will be lost
270 ultimately fails with an inconsistent filesystem and requires an
fsck to repair. The cause of the error is an underflow in
ext4_da_update_reserve_space() due to an unreserved meta block
allocation.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
Whether to continue removing extents or not is decided by the return
value of function ext4_ext_more_to_rm() which checks 2 conditions:
a) if there are no more indexes to process.
b) if the number of entries are decreased in the header of "depth -1".
In case of hole punch, if the last block to be removed is not part of
the last extent index than this index will not be deleted, hence the
number of valid entries in the extent header of "depth - 1" will
remain as it is and ext4_ext_more_to_rm will return 0 although the
required blocks are not yet removed.
This patch fixes the above mentioned problem as instead of removing
the extents from the end of file, it starts removing the blocks from
the particular extent from which removing blocks is actually required
and continue backward until done.
Signed-off-by: Ashish Sangwan <ashish.sangwan2@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Cc: stable@vger.kernel.org
|
|
In net/compat.c::put_cmsg_compat() we may assign 'data' the address of
either the 'ctv' or 'cts' local variables inside the 'if
(!COMPAT_USE_64BIT_TIME)' branch.
Those variables go out of scope at the end of the 'if' statement, so
when we use 'data' further down in 'copy_to_user(CMSG_COMPAT_DATA(cm),
data, cmlen - sizeof(struct compat_cmsghdr))' there's no telling what
it may be refering to - not good.
Fix the problem by simply giving 'ctv' and 'cts' function scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The '__ext4_handle_dirty_metadata()' does not need the 'now' argument
anymore and we can kill it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
|
We do not depend on VFS's '->write_super()' anymore and do not need
the 's_dirt' flag anymore, so weed out 'ext4_write_super()' and
's_dirt'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
|
This patch changes the 'ext4_handle_dirty_super()' function which
submits the superblock for I/O in the following cases:
1. When creating the first large file on a file system without
EXT4_FEATURE_RO_COMPAT_LARGE_FILE feature.
2. When re-sizing the file-system.
3. When creating an xattr on a file-system without the
EXT4_FEATURE_COMPAT_EXT_ATTR feature.
If the file-system has journal enabled, the superblock is written via
the journal. We do not modify this path.
If the file-system has no journal, this function, falls back to just
marking the superblock as dirty using the 's_dirt' superblock
flag. This means that it delays the actual superblock I/O submission
by 5 seconds (default setting). Namely, the 'sync_supers()' kernel
thread will call 'ext4_write_super()' later and will actually submit
the superblock for I/O.
And this is the behavior this patch modifies: we stop using 's_dirt'
and just mark the superblock buffer as dirty right away. Indeed, all 3
cases above are extremely rare and it does not add any value to delay
the I/O submission for them.
Note: 'ext4_handle_dirty_super()' executes
'__ext4_handle_dirty_super()' with 'now = 0'. This patch basically
makes the 'now' argument unneeded and it will be deleted in one of the
next patches.
This patch also removes 's_dirt' condition on the unmount path because
we never set it anymore, so we should not test it.
Tested using xfstests for both journalled and non-journalled ext4.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
|
The last user of ext4_mark_super_dirty() in ext4_file_open() is so
rare it can well be modifying the superblock properly by journalling
the change. Change it and get rid of ext4_mark_super_dirty() as it's
not needed anymore.
Artem: small amendments.
Artem: tested using xfstests for both journalled and non-journalled ext4.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Commit a0375156 properly notes that superblock doesn't need to be marked
as dirty when only number of free inodes / blocks / number of directories
changes since that is recomputed on each mount anyway. However that comment
leaves some unnecessary markings as dirty in place. Remove these.
Artem: tested using xfstests for both journalled and non-journalled ext4.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
Duplicate caused, AFAICS, by mismerge in
ff9cb1c4eead5e4c292e75cd3170a82d66944101>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
|
The ext4_checksum() inline function was using a dynamic array size,
which is not legal C. (It is a gcc extension).
Remove it.
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
This patch adds support for quotas as a first class feature in ext4;
which is to say, the quota files are stored in hidden inodes as file
system metadata, instead of as separate files visible in the file system
directory hierarchy.
It is based on the proposal at:
https://ext4.wiki.kernel.org/index.php/Design_For_1st_Class_Quota_in_Ext4
This patch introduces a new feature - EXT4_FEATURE_RO_COMPAT_QUOTA
which, when turned on, enables quota accounting at mount time
iteself. Also, the quota inodes are stored in two additional superblock
fields. Some changes introduced by this patch that should be pointed
out are:
1) Two new ext4-superblock fields - s_usr_quota_inum and
s_grp_quota_inum for storing the quota inodes in use.
2) Default quota inodes are: inode#3 for tracking userquota and inode#4
for tracking group quota. The superblock fields can be set to use
other inodes as well.
3) If the QUOTA feature and corresponding quota inodes are set in
superblock, the quota usage tracking is turned on at mount time. On
'quotaon' ioctl, the quota limits enforcement is turned
on. 'quotaoff' ioctl turns off only the limits enforcement in this
case.
4) When QUOTA feature is in use, the quota mount options 'quota',
'usrquota', 'grpquota' are ignored by the kernel.
5) mke2fs or tune2fs can be used to set the QUOTA feature and initialize
quota inodes. The default reserved inodes will not be visible to user
as regular files.
6) The quota-tools will need to be modified to support hidden quota
files on ext4. E2fsprogs will also include support for creating and
fixing quota files.
7) Support is only for the new V2 quota file format.
Tested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Johann Lombardi <johann@whamcloud.com>
Signed-off-by: Aditya Kali <adityakali@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
Aligned and overwrite direct I/O can be parallelized. In
ext4_file_dio_write, we first check whether these conditions are
satisfied or not. If so, we take i_data_sem and release i_mutex lock
directly. Meanwhile iocb->private is set to indicate that this is a
dio overwrite, and it will be handled in ext4_ext_direct_IO.
[ Added fix from Dan Carpenter to fix locking bug on the error path. ]
CC: Tao Ma <tm@tao.ma>
CC: Eric Sandeen <sandeen@redhat.com>
CC: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
|
|
The ipv4 routing cache is non-deterministic, performance wise, and is
subject to reasonably easy to launch denial of service attacks.
The routing cache works great for well behaved traffic, and the world
was a much friendlier place when the tradeoffs that led to the routing
cache's design were considered.
What it boils down to is that the performance of the routing cache is
a product of the traffic patterns seen by a system rather than being a
product of the contents of the routing tables. The former of which is
controllable by external entitites.
Even for "well behaved" legitimate traffic, high volume sites can see
hit rates in the routing cache of only ~%10.
The general flow of this patch series is that first the routing cache
is removed. We build a completely new rtable entry every lookup
request.
Next we make some simplifications due to the fact that removing the
routing cache causes several members of struct rtable to become no
longer necessary.
Then we need to make some amends such that we can legally cache
pre-constructed routes in the FIB nexthops. Firstly, we need to
invalidate routes which are hit with nexthop exceptions. Secondly we
have to change the semantics of rt->rt_gateway such that zero means
that the destination is on-link and non-zero otherwise.
Now that the preparations are ready, we start caching precomputed
routes in the FIB nexthops. Output and input routes need different
kinds of care when determining if we can legally do such caching or
not. The details are in the commit log messages for those changes.
The patch series then winds down with some more struct rtable
simplifications and other tidy ups that remove unnecessary overhead.
On a SPARC-T3 output route lookups are ~876 cycles. Input route
lookups are ~1169 cycles with rpfilter disabled, and about ~1468
cycles with rpfilter enabled.
These measurements were taken with the kbench_mod test module in the
net_test_tools GIT tree:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net_test_tools.git
That GIT tree also includes a udpflood tester tool and stresses
route lookups on packet output.
For example, on the same SPARC-T3 system we can run:
time ./udpflood -l 10000000 10.2.2.11
with routing cache:
real 1m21.955s user 0m6.530s sys 1m15.390s
without routing cache:
real 1m31.678s user 0m6.520s sys 1m25.140s
Performance undoubtedly can easily be improved further.
For example fib_table_lookup() performs a lot of excessive
computations with all the masking and shifting, some of it
conditionalized to deal with edge cases.
Also, Eric's no-ref optimization for input route lookups can be
re-instated for the FIB nexthop caching code path. I would be really
pleased if someone would work on that.
In fact anyone suitable motivated can just fire up perf on the loading
of the test net_test_tools benchmark kernel module. I spend much of
my time going:
bash# perf record insmod ./kbench_mod.ko dst=172.30.42.22 src=74.128.0.1 iif=2
bash# perf report
Thanks to helpful feedback from Joe Perches, Eric Dumazet, Ben
Hutchings, and others.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 9778b696a0188ad3b3524b383953ee73b31b7b68 accidentally added
a .rej file (probably my fault), remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.6:
Core:
- Rename cd-gpio to slot-gpio and extend it to support more slot GPIO
functions, such as write-protect.
- Add a function to get regulators (Vdd and Vccq) for a host.
Drivers:
- sdhci-pxav2, sdhci-pxav3: Add device tree support.
- sdhi: Add device tree support.
- sh_mmcif: Add support for regulators, device tree, slot-gpio.
- tmio: Add regulator support, use slot-gpio."
* tag 'mmc-merge-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (62 commits)
mmc: sdhci-dove: Prepare for common clock framework
mmc: sdhci-dove: Add SDHCI_QUIRK_NO_HISPD_BIT
mmc: omap_hsmmc: ensure probe returns error upon resource failure
mmc: mxs-mmc: Add wp-inverted property
mmc: esdhc: Fix DMA_MASK to not break mx25 DMA access
mmc: core: reset signal voltage on power up
mmc: sd: Fix sd current limit setting
mmc: omap_hsmmc: add clk_prepare and clk_unprepare
mmc: sdhci: When a UHS switch fails, cycle power if regulator is used
mmc: atmel-mci: modify CLKDIV displaying in debugfs
mmc: atmel-mci: fix incorrect setting of host->data to NULL
mmc: sdhci: poll for card even when card is logically unremovable
mmc: sdhci: Introduce new flag SDHCI_USING_RETUNING_TIMER
mmc: sdio: Change pr_warning to pr_warn_ratelimited
mmc: core: Simplify and fix for SD switch processing
mmc: sdhci: restore host settings when card is removed
mmc: sdhci: fix incorrect command used in tuning
mmc: sdhci-pci: CaFe has broken card detection
mmc: sdhci: Report failure reasons for all cases in sdhci_add_host()
mmc: s3cmci: Convert s3cmci driver to gpiolib API
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/mce changes from Ingo Molnar:
"This tree improves the AMD thresholding bank code and includes a
memory fault signal handling fixlet."
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix siginfo_t->si_addr value for non-recoverable memory faults
x86, MCE, AMD: Update copyrights and boilerplate
x86, MCE, AMD: Give proper names to the thresholding banks
x86, MCE, AMD: Make error_count read only
x86, MCE, AMD: Cleanup reading of error_count
x86, MCE, AMD: Print decimal thresholding values
x86, MCE, AMD: Move shared bank to node descriptor
x86, MCE, AMD: Remove local_allocate_... wrapper
x86, MCE, AMD: Remove shared banks sysfs linking
x86, amd_nb: Export model 0x10 and later PCI id
|
|
As mach-dove is moving towards common clock framework prepare
the sdhci driver to grab its clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
