| Age | Commit message (Collapse) | Author |
|---|
|
ila_xlat_nl_cmd_flush uses rhashtable walkers allocated from the
stack but it never frees them. This corrupts the walker list of
the hash table.
This patch fixes it.
Reported-by: syzbot+dae72a112334aa65a159@syzkaller.appspotmail.com
Fixes: b6e71bdebb12 ("ila: Flush netlink command to clear xlat...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAINTAINERS still pointed to phy.txt after moving this file into the rst
format, fix this.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 25fe02d00a1e ("Documentation: net: phy: switch documentation to rst format")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christoph reported a stall while peeking datagram with an offset when
busy polling is enabled. __skb_try_recv_datagram() uses as the loop
termination condition 'queue empty'. When peeking, the socket
queue can be not empty, even when no additional packets are received.
Address the issue explicitly checking for receive queue changes,
as currently done by __skb_wait_for_more_packets().
Fixes: 2b5cd0dfa384 ("net: Change return type of sk_busy_loop from bool to void")
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[Why]
VBIOS will not post pixel rate > 340MHz.
If driver set pixel rate > 340MHz and do restart bottom, VBIOS can't
post HDMI monitor due to monitor is stay in HDMI2.0 state.
[How]
Program Scrambling_Enable and TMDS_Bit_Clock_Ratio when disable stream.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If DAL requires to force MCLK high, the FCLK will be
forced to high also.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Avoid left shift overflow.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's OK to have this feature bit with old SMU firmwares.
But the feature should be disabled on them.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
use pcie_bandwidth_available to get real link state
to update pcie table.
v2: fix incorrect initialized return value
v3: expand the fetching method about the link width to all asics.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No change to functionality. Simply make transport event messages a little
clearer, and rework CRQ format enums such that we have separate enums for
INIT messages and XPORT events.
[mkp: typo]
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Status and error codes are returned in big endian from the VIOS. The values
are translated into a human readable format when logged, but the values are
also logged. This patch byte swaps those values so that they are consistent
between BE and LE platforms.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The VIOS uses the SCSI_ERROR class to report PRLI failures. These errors
are indicated with the combination of a IBMVFC_FC_SCSI_ERROR return status
and 0x8000 error code. Add these codes to cmd_status[] with appropriate
human readable error message.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The text of messages logged with ibmvfc_log_error() always contain the term
"failed". In the case of cancelled commands during EH they are reported
back by the VIOS using error codes. This can be confusing to somebody
looking at these log messages as to whether a command was successfully
cancelled. The following real log message for example it is unclear if the
transaction was actaully cancelled.
<6>sd 0:0:1:1: Cancelling outstanding commands.
<3>sd 0:0:1:1: [sde] Command (28) failed: transaction cancelled (2:6) flags: 0 fcp_rsp: 0, resid=0, scsi_status: 0
Remove prefixing of "failed" to all error logged messages. The
ibmvfc_log_error() function translates the returned error/status codes to a
human readable message already.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away. It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.
The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.
The call chain was:
zfcp_fc_incoming_rscn
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:
zfcp_fc_incoming_rscn
if (no_entries > 1) <===
list_for_each_entry(port, &adapter->port_list, list) <===
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
Abbreviated example trace records before this code change:
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x02
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x00 NOP => superfluous trace record
The last trace entry repeats if there are more than 2 RSCN elements.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit
ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org> #3.0+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery")
Cc: <stable@vger.kernel.org> #2.6.32+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes: a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size")
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Reported-by: Hussam Al-Tayeb <ht990332@gmx.com>
Tested-by: Hussam Al-Tayeb <ht990332@gmx.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
scsi_mq_uninit_cmd+0x1c/0x30
scsi_end_request+0x7c/0x1b8
scsi_io_completion+0x464/0x668
scsi_finish_command+0xbc/0x160
scsi_eh_flush_done_q+0x10c/0x170
sas_scsi_recover_host+0x84c/0xa98 [libsas]
scsi_error_handler+0x140/0x5b0
kthread+0x100/0x12c
ret_from_fork+0x10/0x18
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use dd to test a SCSI device:
1. echo "blocked" >/sys/block/sda/device/state
2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10
3. echo "running" >/sys/block/sda/device/state
dd should finish this work after step 3, but it hangs.
After step2, the call chain is this:
blk_mq_dispatch_rq_list-->scsi_queue_rq-->prep_to_mq
prep_to_mq will return BLK_STS_RESOURCE, and scsi_queue_rq will
transition it to BLK_STS_DEV_RESOURCE which means that driver can
guarantee that IO dispatch will be triggered in future when the
resource is available. Need to follow the rule if we set the device
state to running.
[mkp: tweaked commit description and code comment as suggested by Bart]
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
|
|
According to Amit Klein and Benny Pinkas, IP ID generation is too weak
and might be used by attackers.
Even with recent net_hash_mix() fix (netns: provide pure entropy for net_hash_mix())
having 64bit key and Jenkins hash is risky.
It is time to switch to siphash and its 128bit keys.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check for zero timeout is always true at the end of the proceeding
while loop; the only other exit path in the loop is if the unimac MDIO
is not busy. Remove the redundant zero timeout check and always
return -ETIMEDOUT on this timeout return path.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My recent patch had at least three problems :
1) TX zerocopy wants notification when skb is acknowledged,
thus we need to call skb_zcopy_clear() if the skb is
cached into sk->sk_tx_skb_cache
2) Some applications might expect precise EPOLLOUT
notifications, so we need to update sk->sk_wmem_queued
and call sk_mem_uncharge() from sk_wmem_free_skb()
in all cases. The SOCK_QUEUE_SHRUNK flag must also be set.
3) Reuse of saved skb should have used skb_cloned() instead
of simply checking if the fast clone has been freed.
Fixes: 472c2e07eef0 ("tcp: add one skb cache for tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new action - 'check_pkt_len' which checks the
packet length and executes a set of actions if the packet
length is greater than the specified length or executes
another set of actions if the packet length is lesser or equal to.
This action takes below nlattrs
* OVS_CHECK_PKT_LEN_ATTR_PKT_LEN - 'pkt_len' to check for
* OVS_CHECK_PKT_LEN_ATTR_ACTIONS_IF_GREATER - Nested actions
to apply if the packet length is greater than the specified 'pkt_len'
* OVS_CHECK_PKT_LEN_ATTR_ACTIONS_IF_LESS_EQUAL - Nested
actions to apply if the packet length is lesser or equal to the
specified 'pkt_len'.
The main use case for adding this action is to solve the packet
drops because of MTU mismatch in OVN virtual networking solution.
When a VM (which belongs to a logical switch of OVN) sends a packet
destined to go via the gateway router and if the nic which provides
external connectivity, has a lesser MTU, OVS drops the packet
if the packet length is greater than this MTU.
With the help of this action, OVN will check the packet length
and if it is greater than the MTU size, it will generate an
ICMP packet (type 3, code 4) and includes the next hop mtu in it
so that the sender can fragment the packets.
Reported-at:
https://mail.openvswitch.org/pipermail/ovs-discuss/2018-July/047039.html
Suggested-by: Ben Pfaff <blp@ovn.org>
Signed-off-by: Numan Siddique <nusiddiq@redhat.com>
CC: Gregory Rose <gvrose8192@gmail.com>
CC: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Heiner Kallweit says:
====================
ethtool: add support for Fast Link Down as new PHY tunable
This adds support for Fast Link Down as new PHY tunable.
Fast Link Down reduces the time until a link down event is reported
for 1000BaseT. According to the standard it's 750ms what is too long
for several use cases.
This is the kernel-related series, the ethtool userspace extension
I'd submit once the kernel part has been applied.
v2:
- add describing comment in patch 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1000BaseT standard requires that a link is reported as down earliest
after 750ms. Several use case however require a much faster detecion
of a broken link. Fast Link Down supports this by intentionally
violating a the standard. This patch exposes the Fast Link Down
feature of 88E1540 and 88E6390. These PHY's can be found as internal
PHY's in several switches: 88E6352, 88E6240, 88E6176, 88E6172,
and 88E6390(X). Fast Link Down and EEE are mutually exclusive.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for Fast Link Down as new PHY tunable.
Fast Link Down reduces the time until a link down event is reported
for 1000BaseT. According to the standard it's 750ms what is too long
for several use cases.
v2:
- add comment describing the constants
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of declaring a function in a .c file, declare it in a header
file and include that header file from the source files that define
and that use the function. That allows the compiler to verify
consistency of declaration and definition. See also commit
52267790ef52 ("sock: add MSG_ZEROCOPY") # v4.14.
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids that the following warnings are reported when building
with W=1:
net/core/rtnetlink.c:3580: warning: Function parameter or member 'ndm' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'tb' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'dev' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'addr' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'vid' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3580: warning: Function parameter or member 'flags' not described in 'ndo_dflt_fdb_add'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'ndm' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'tb' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'dev' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'addr' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3718: warning: Function parameter or member 'vid' not described in 'ndo_dflt_fdb_del'
net/core/rtnetlink.c:3861: warning: Function parameter or member 'skb' not described in 'ndo_dflt_fdb_dump'
net/core/rtnetlink.c:3861: warning: Function parameter or member 'cb' not described in 'ndo_dflt_fdb_dump'
net/core/rtnetlink.c:3861: warning: Function parameter or member 'filter_dev' not described in 'ndo_dflt_fdb_dump'
net/core/rtnetlink.c:3861: warning: Function parameter or member 'idx' not described in 'ndo_dflt_fdb_dump'
net/core/rtnetlink.c:3861: warning: Excess function parameter 'nlh' description in 'ndo_dflt_fdb_dump'
Cc: Hubert Sokolowski <hubert.sokolowski@intel.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids that the following warning is reported when building
with W=1:
warning: Function parameter or member 'flags' not described in '__skb_flow_dissect'
Cc: Tom Herbert <tom@herbertland.com>
Fixes: cd79a2382aa5 ("flow_dissector: Add flags argument to skb_flow_dissector functions") # v4.3.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids that the following warnings are reported when building
with W=1:
net/core/dev_ioctl.c:378: warning: Function parameter or member 'ifr' not described in 'dev_ioctl'
net/core/dev_ioctl.c:378: warning: Function parameter or member 'need_copyout' not described in 'dev_ioctl'
net/core/dev_ioctl.c:378: warning: Excess function parameter 'arg' description in 'dev_ioctl'
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: 44c02a2c3dc5 ("dev_ioctl(): move copyin/copyout to callers") # v4.16.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch avoids that the following warning is reported when building
with W=1:
warning: Function parameter or member 'bind_inany' not described in 'reuseport_add_sock'
Cc: Martin KaFai Lau <kafai@fb.com>
Fixes: 2dbb9b9e6df6 ("bpf: Introduce BPF_PROG_TYPE_SK_REUSEPORT") # v4.19.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This partially reverts ed8fe20205ac ("net: dsa: mv88e6xxx: prevent
interrupt storm caused by mv88e6390x_port_set_cmode"). I missed
that chip->ports[].cmode is overwritten anyway by the cmode
caching in mv88e6xxx_setup().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8fcf0ec44c11f "bnx2x: Add FW 7.13.11.0" added said .bin FW to
linux-firmware; This patch incorporates the FW in the bnx2x driver.
This introduces few FW fixes and the support for Tx VLAN filtering.
Please consider applying it to 'net-next' tree.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An FoU socket is currently bound to the wildcard-address. While this
works fine, there are several use-cases where the use of the
wildcard-address is not desirable. For example, I use FoU on some
multi-homed servers and would like to use FoU on only one of the
interfaces.
This commit adds support for binding FoU sockets to a given source
address/interface, as well as connecting the socket to a given
destination address/port. udp_tunnel already provides the required
infrastructure, so most of the code added is for exposing and setting
the different attributes (local address, peer address, etc.).
The lookups performed when we add, delete or get an FoU-socket has also
been updated to compare all the attributes a user can set. Since the
comparison now involves several elements, I have added a separate
comparison-function instead of open-coding.
In order to test the code and ensure that the new comparison code works
correctly, I started by creating a wildcard socket bound to port 1234 on
my machine. I then tried to create a non-wildcarded socket bound to the
same port, as well as fetching and deleting the socket (including source
address, peer address or interface index in the netlink request). Both
the create, fetch and delete request failed. Deleting/fetching the
socket was only successful when my netlink request attributes matched
those used to create the socket.
I then repeated the tests, but with a socket bound to a local ip
address, a socket bound to a local address + interface, and a bound
socket that was also «connected» to a peer. Add only worked when no
socket with the matching source address/interface (or wildcard) existed,
while fetch/delete was only successful when all attributes matched.
In addition to testing that the new code work, I also checked that the
current behavior is kept. If none of the new attributes are provided,
then an FoU-socket is configured as before (i.e., wildcarded). If any
of the new attributes are provided, the FoU-socket is configured as
expected.
v1->v2:
* Fixed building with IPv6 disabled (kbuild).
* Fixed a return type warning and make the ugly comparison function more
readable (kbuild).
* Describe more in detail what has been tested (thanks David Miller).
* Make peer port required if peer address is specified.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:
1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.
2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.
3) Fix documentation for some eBPF helpers, from Quentin Monnet.
4) Some UAPI bpf header sync with tools, also from Quentin Monnet.
5) Set descriptor ownership bit at the right time for jumbo frames in
stmmac driver, from Aaro Koskinen.
6) Set IFF_UP properly in tun driver, from Eric Dumazet.
7) Fix load/store doubleword instruction generation in powerpc eBPF
JIT, from Naveen N. Rao.
8) nla_nest_start() return value checks all over, from Kangjie Lu.
9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
merge window. From Marcelo Ricardo Leitner and Xin Long.
10) Fix memory corruption with large MTUs in stmmac, from Aaro
Koskinen.
11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
Dumazet.
12) Fix topology subscription cancellation in tipc, from Erik Hugne.
13) Memory leak in genetlink error path, from Yue Haibing.
14) Valid control actions properly in packet scheduler, from Davide
Caratti.
15) Even if we get EEXIST, we still need to rehash if a shrink was
delayed. From Herbert Xu.
16) Fix interrupt mask handling in interrupt handler of r8169, from
Heiner Kallweit.
17) Fix leak in ehea driver, from Wen Yang"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
dpaa2-eth: fix race condition with bql frame accounting
chelsio: use BUG() instead of BUG_ON(1)
net: devlink: skip info_get op call if it is not defined in dumpit
net: phy: bcm54xx: Encode link speed and activity into LEDs
tipc: change to check tipc_own_id to return in tipc_net_stop
net: usb: aqc111: Extend HWID table by QNAP device
net: sched: Kconfig: update reference link for PIE
net: dsa: qca8k: extend slave-bus implementations
net: dsa: qca8k: remove leftover phy accessors
dt-bindings: net: dsa: qca8k: support internal mdio-bus
dt-bindings: net: dsa: qca8k: fix example
net: phy: don't clear BMCR in genphy_soft_reset
bpf, libbpf: clarify bump in libbpf version info
bpf, libbpf: fix version info and add it to shared object
rxrpc: avoid clang -Wuninitialized warning
tipc: tipc clang warning
net: sched: fix cleanup NULL pointer exception in act_mirr
r8169: fix cable re-plugging issue
net: ethernet: ti: fix possible object reference leak
net: ibm: fix possible object reference leak
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-03-26
This series contains more updates to the ice driver only.
Jeremiah provides his first patch to the Linux kernel to clean up
un-necessary newlines in driver log messages.
Mitch updates the ice driver to use existing status codes in the iavf
driver so that when errors occur, it will not report nonsensical
results. Adds support for VF admin queue interrupts by programming the
VPINT_MBX_CTL register array.
Brett adds a check for a bit that we set while preparing for a reset, to
ensure we are prepared to do a proper reset. Also implemented PCI error
handling operations. Went through and audited the hot path with pahole
and made modifications based on the results since 2 structures were
taking up more space than necessary due to cache alignment issues.
Fixed an issue where when flow control was disabled, the state of flow
control was being displayed as "Unknown".
Anirudh fixes adaptive interrupt moderation changes by adding code that
was missed, that should have been added in the initial patch to add that
support. Cleaned up a function prototype that was never implemented.
Did additional code cleanup by removing unneeded braces and redundant
code comments.
Akeem fixes an issue that occurs when the VF is attempting to remove the
default LAN/MAC address, which is programmed by the administrator by
updating the error message to explicitly say that the VF cannot change
the MAC programmed by the PF.
Preethi fixes the driver to not fall into the error path when a added
filter already exists, but instead continue to process the rest of the
function and add appropriate checks after adding MAC filters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we use "crashkernel=Y[@X]" and the start address is above 4G,
the arm64 kdump capture kernel may call memblock_alloc_low() failure
in request_standard_resources(). Replacing memblock_alloc_low() with
memblock_alloc().
[ 0.000000] MEMBLOCK configuration:
[ 0.000000] memory size = 0x0000000040650000 reserved size = 0x0000000004db7f39
[ 0.000000] memory.cnt = 0x6
[ 0.000000] memory[0x0] [0x00000000395f0000-0x000000003968ffff], 0x00000000000a0000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x1] [0x0000000039730000-0x000000003973ffff], 0x0000000000010000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x2] [0x0000000039780000-0x000000003986ffff], 0x00000000000f0000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x3] [0x0000000039890000-0x0000000039d0ffff], 0x0000000000480000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x4] [0x000000003ed00000-0x000000003ed2ffff], 0x0000000000030000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x5] [0x0000002040000000-0x000000207fffffff], 0x0000000040000000 bytes on node 0 flags: 0x0
[ 0.000000] reserved.cnt = 0x7
[ 0.000000] reserved[0x0] [0x0000002040080000-0x0000002041c4dfff], 0x0000000001bce000 bytes flags: 0x0
[ 0.000000] reserved[0x1] [0x0000002041c53000-0x0000002042c203f8], 0x0000000000fcd3f9 bytes flags: 0x0
[ 0.000000] reserved[0x2] [0x000000207da00000-0x000000207dbfffff], 0x0000000000200000 bytes flags: 0x0
[ 0.000000] reserved[0x3] [0x000000207ddef000-0x000000207fbfffff], 0x0000000001e11000 bytes flags: 0x0
[ 0.000000] reserved[0x4] [0x000000207fdf2b00-0x000000207fdfc03f], 0x0000000000009540 bytes flags: 0x0
[ 0.000000] reserved[0x5] [0x000000207fdfd000-0x000000207ffff3ff], 0x0000000000202400 bytes flags: 0x0
[ 0.000000] reserved[0x6] [0x000000207ffffe00-0x000000207fffffff], 0x0000000000000200 bytes flags: 0x0
[ 0.000000] Kernel panic - not syncing: request_standard_resources: Failed to allocate 384 bytes
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.1.0-next-20190321+ #4
[ 0.000000] Call trace:
[ 0.000000] dump_backtrace+0x0/0x188
[ 0.000000] show_stack+0x24/0x30
[ 0.000000] dump_stack+0xa8/0xcc
[ 0.000000] panic+0x14c/0x31c
[ 0.000000] setup_arch+0x2b0/0x5e0
[ 0.000000] start_kernel+0x90/0x52c
[ 0.000000] ---[ end Kernel panic - not syncing: request_standard_resources: Failed to allocate 384 bytes ]---
Link: https://www.spinics.net/lists/arm-kernel/msg715293.html
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Maxime Chevallier says:
====================
net: mvpp2: Classifier updates and cleanups
In preparation for the future addition of classification offload
support, this series cleans-up the current code dealing with the
classification engines.
As of today, the classification code only deals with RSS, which is a
very narrow use-case when considering all of the classifier's features.
This lead to design and naming decisions that don't really stand when
considering using more classification features.
This series therefore includes quite a lot a renaming of functions and
macros, and tries to make the naming schemes more consistent and the
code more readable.
The debugfs interface that allows reading the various Parsing and
Classification engines has been cleaned-up and made more generic,
allowing to read the Flow Table and C2 engine hit counters on a
per-entry basis.
The Classifier itself has been made more robust by introducing the
lu_type field in classification lookups, that prevents false-positive
matches in the future. We also initialise the various engine in a more
extensive and less error-prone way by assining default values to all
entries in the C2 and Flow table.
This is a pretty big series considering it's mostly cleanup, but my goal
is to make the future series that will contain new big features easier
to review, focusing on the real logic.
Besides the debugfs interface, this series doesn't intend to introduce any
new features or change in behaviours.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The C2 classification engine has a 256 entry TCAM, used for ternary
matches on an 8 byte Header Extracted Key. For now, we compute the
various indices for classification and RSS that use this engine thanks
to a set of macros.
This commit mainly renames the macros used to make it clear that they
should be used with the C2 engine, but also make use of the full 256
entries in the engine. For now, the C2 entries are only used for RSS.
These entries are put at the end of the TCAM range, in case we want to
add higher priority matches later on.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When classifying a packet pertaining to a given flow, the classifier
will issue multiple lookup commands until it finds one with the 'last'
bit set. It expects all prorities to be assign continuously (although
not necessarily in an ordered fashion) from 0 to the number of lookups.
We can initialize this once, and make sure unused lookups are given an
empty port map. This avoids having to maintain priorities and the
information of which lookup is the last.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
C2 TCAM entries can be invalidated to avoid unwanted matches. Make sure
all entries are invalidated at init, then validate only the ones we use.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Flow Table dictates what lookups will be issued for each flow type.
The lookup sequence for each flow is similar, and the index of each
lookup is computed by some macros.
There are similar mechanisms for the C2 TCAM lookups, so in order to
avoid confusion, rename the flow table index computing macros with a
common prefix.
The only difference in behaviour is that we now use the very first entry
in the flow for the RSS lookup (the first entry was previously unused).
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The classifier allows to combine multiple lookups in one "sequence" that
is counted as a single lookup to an engine, with a single result.
We don't actually use that feature, so remove any places where we set
this field, so that the classifier doesn't try to interpret these
fields.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit renames some of the classifier functions to follow the
naming 'mvpp2_port_*' that's used for function that act on a given port.
This commit is purely cosmetic.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move C2 read/write helpers higher in the file to ease future work that
rely on these helpers
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When writing a C2 entry to hardware, some registers writes will only
take effect when the TCAM_DATA4 register is written. This includes all
C2 TCAM registers, and the C2 invalidate register.
To make sure we always write C2 entries correctly, document that
behaviour with a comment, and move TCAM writes to the end of the
mvpp2_cls_c2_write helper.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cls_table is a global read-only table containing the different
parameters that are used by various tables in the classifier. It
describes the links between the Header Parser, the decoding table and
the flow_table.
There are several possible way we want to iterate over that table,
depending on wich classifier engine we want to configure. For the Header
Parser, we want to iterate over each entry. For the Decoding table, we
want to iterate over each entry having a unique flow_id. Finally, when
configuring an ethtool flow, we want to iterate over each entry having a
unique flow_id and that has a given flow_type.
This commit introduces some iterator to both provide syntactic sugar and
also clarify the way we want to iterate over the table.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPv2's Classifier uses multiple engines to perform classification. So
far, only the C2 engine is used, which has a 256 entries TCAM.
So far, we only accessed the relevant entries from the C2 engines, which
are the one implementing RSS. To implement and debug ntuple
classification offload, beaing able to see the hit count for each C2
entry is helpful, so this commit moves the logic to a dedicated
directory allowing to access each entry.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Classifier flow table is the central part of the PPv2 Classifier,
since it describes all classification steps performed for each flow.
It has 512 entries, shared between all ports, which are divided into
sequences that are pointed-to by the decoding table. Being able to see
which entries in the flow table were hit is a key point when
implementing and debugging classification offload.
This commit allows reading each flow table entry's hit count
independently, with a clear-on-read behaviour.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
