| Age | Commit message (Collapse) | Author |
|---|
|
return type of wait_for_completion_timeout is unsigned long not int, this
patch adds an appropriate variable and fixes up the assignment. It removes
the else branch as the only thing it was doing is assigning ret = 0; - but
ret is never used thereafter so that is not needed. As the string in
dev_err already states "timeout" there is little point in printing the 0.
A typo in "trasfer" -> transfer is also fixed.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add missing stubs for regulator_suspend_prepare() and
regulator_suspend_finish() to fix exynos_defconfig build without
REGULATOR:
arch/arm/mach-exynos/built-in.o: In function `exynos_suspend_finish':
arch/arm/mach-exynos/suspend.c:537: undefined reference to `regulator_suspend_finish'
arch/arm/mach-exynos/built-in.o: In function `exynos_suspend_prepare':
arch/arm/mach-exynos/suspend.c:520: undefined reference to `regulator_suspend_prepare'
make: *** [vmlinux] Error 1
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Joerg Roedel <joro@8bytes.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge fbdev topic branches
|
|
the check of the return code is missing, user space does not get notified
about the error condition:
omapdss OVERLAY error: overlay 2 horizontally not inside the display area (403 + 800 >= 800)
omapdss APPLY error: failed to apply settings: illegal configuration.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add support for DRA7xx DPI output.
DRA7xx has three DPI outputs, each of which gets its input from a DISPC
channel. However, DRA72x has only one video PLL, and DRA74x has two
video PLLs. In both cases the video PLLs need to be shared between
multiple outputs. The driver doesn't handle this at the moment.
Also, DRA7xx requires configuring CONTROL module bits to route the clock
from the PLL to the used DISPC channel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add support for DRA7xx to the HDMI driver.
The HDMI block on DRA7xx is the same as on OMAP5, except we need to
enable and disable the HDMI PLL via the CONTROL module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
On DRA7xx, DISPC needs to write output signal polarities not only to a
DISPC register, like for all earlier DSS versions, but to control
module's CTRL_CORE_SMA_SW_1 register.
This patch adds support to write the polarities to control module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add DRA7xx support to DISPC driver. The DISPC block is the same as on
OMAP5, except the PLL's used for clocking are "videoX", not "dsiX".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DRA7xx SoCs have one (DRA72x) or two (DRA74x) video PLLs. They are
basically the same as DSI PLLs on OMAPs, but without the rest of the DSI
hardware. The video PLLs also require some configuration via the CONTROL
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add functions which configure the control module register
CTRL_CORE_DSS_PLL_CONTROL found in DRA7xx SoCs. This register configures
whether the PLL registers are accessed internally by DSS, or externally
using OCP2SCP interface. They also configure muxes which route the PLL
output to a particular LCD overlay manager within DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add base support for DRA7xx to DSS core.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add device tree binding documentation for DRA7xx display subsystem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
|
|
Add define for DRA7xx DSS version.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
A race issue has been observed with the encoder-tpd12s015 driver, which
leads to errors when trying to read EDID. This has only now been
observed, as OMAP4 and OMAP5 boards used SoC's GPIOs for LS_OE GPIO. On
dra7-evm boards, the LS_OE is behind a i2c controlled GPIO expander,
which increases the time to set the LS_OE.
This patch simplifies the handling of the LS_OE gpio in the driver by
removing the interrupt handling totally. The only time we actually need
to enable LS_OE is when we are reading the EDID, and thus we can just
set and clear the LS_OE gpio inside the read_edid() function.
This also has the additional benefit of very slightly decreasing the
power consumption.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The OMAP5 HW supports directing DIGIT channel to DPI output, but the
driver doesn't support that. However, we have marked that configuration
as possible in the dss features, so in certain cases the driver tries to
use that configuration, leading to broken display.
Fix the problem by allowing DIGIT channel to go only to HDMI output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The port arrays are constant data, so set them as 'const'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add a helper function to wait until the PLL's reset is done.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
In some cases we need global identifiers for the DSS PLLs, for example
when configuring clock muxing on DRA7. For this purpose let's add a
'enum dss_pll_id'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The intercon_extra_3104 is obviously for tlv320aic3104.
Reported-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename CONFIG_LIVE_PATCHING to CONFIG_LIVEPATCH to make the naming of
the config and the code more consistent.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
leaf_dealloc uses vzalloc as a fallback to kzalloc(GFP_NOFS), so
it clearly does not want any shrinker activity within the fs itself.
convert vzalloc into __vmalloc(GFP_NOFS|__GFP_ZERO) to better achieve
this goal.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
If the pin is in HiZ mode when it is requested as GPIO its value cannot be
read (it always returns 0). In order to cope with the Linux GPIO subsystem
where we do not have such state at all, turn the pin to be input instead.
Reported-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch provides a simple mmc-pwrseq-emmc driver, which controls
single gpio line. It perform standard eMMC hw reset procedure, as
descibed by Jedec 4.4 specification. This procedure is performed just
after MMC core enabled power to the given mmc host (to fix possible
issues if bootloader has left eMMC card in initialized or unknown
state), and before performing complete system reboot (also in case of
emergency reboot call). The latter is needed on boards, which doesn't
have hardware reset logic connected to emmc card and (limited or broken)
ROM bootloaders are unable to read second stage from the emmc card if
the card is left in unknown or already initialized state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Jonas Jensen wanted to submit a patch for these, but apparently
forgot about it. I stumbled over this symptom first:
drivers/built-in.o: In function `moxart_probe':
:(.text+0x2af128): undefined reference to `of_dma_request_slave_channel'
This is because of_dma_request_slave_channel is an internal helper
and not exported to loadable module. I'm changing the driver to
use dma_request_slave_channel_reason() instead.
Further problems from inspection:
* The remove function must not call kfree on the host pointer,
because it is allocated together with the mmc_host.
* The clock is never released
* The dma_cap_mask_t is completely unused and can be removed
* deferred probing does not work if the dma driver is loaded
after the mmc driver.
This patch should fix all of the above.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
NFCEE_DISCOVER_CMD is a specified NCI command used to discover
NFCEE IDs.
Move nci_nfcee_discover() call to nci_discover_se() in order to
guarantee:
- NFCEE_DISCOVER_CMD run when the NCI state machine is initialized
- NFCEE_DISCOVER_CMD is not run in case there is not discover_se
hook defined by a NFC device driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
conn_info is currently allocated only after nfcee_discovery_ntf
which is not generic enough for logical connection other than
NFCEE. The corresponding conn_info is now created in
nci_core_conn_create_rsp().
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
For consistency sake change nci_core_conn_create_rsp structure
credits field to credits_cnt.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current implementation limits nci_core_conn_create_req()
to only manage NCI_DESTINATION_NFCEE.
Add new parameters to nci_core_conn_create() to support all
destination types described in the NCI specification.
Because there are some parameters with variable size dynamic
buffer allocation is needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The NCI_STATIC_RF_CONN_ID logical connection is the most used
connection. Keeping it directly accessible in the nci_dev
structure will simplify and optimize the access.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The 3.2 revision has a different target BMI
version so it wasn't recognized by ath10k (despite
the chip_id rev being on the supported list
already).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.
To configure log level as WARN:
echo 0xffffffff 2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
The values are:
VERBOSE 0
INFO 1
WARN 2
ERR 3
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Otherwise ath10k will just checksum everything even if it did not
go through the TCP/IP stack (for example bridged frames). In the worst
case this could mean recreating the checksum for incorrect data.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This should fix a very rare occurrence of the following deadlock:
[<ffffffffa018265e>] ath10k_wmi_tx_beacons_nowait+0x1e/0x50 [ath10k_core]
[<ffffffffa01829b6>] ath10k_wmi_op_ep_tx_credits+0x16/0x40 [ath10k_core]
[<ffffffffa017d685>] ath10k_htc_send+0x285/0x3d0 [ath10k_core]
[<ffffffffa0184b81>] ath10k_wmi_cmd_send_nowait+0x81/0x110 [ath10k_core]
[<ffffffffa0184c61>] ath10k_wmi_tx_beacon_nowait.part.33+0x51/0x90 [ath10k_core]
[<ffffffffa0184cd0>] ath10k_wmi_tx_beacons_iter+0x30/0x40 [ath10k_core]
[<ffffffff81882246>] __iterate_active_interfaces+0xa6/0x100
[<ffffffffa0184ca0>] ? ath10k_wmi_tx_beacon_nowait.part.33+0x90/0x90 [ath10k_core]
[<ffffffff818822ae>] ieee80211_iterate_active_interfaces_atomic+0xe/0x10
[<ffffffffa0182676>] ath10k_wmi_tx_beacons_nowait+0x36/0x50 [ath10k_core]
[<ffffffffa01829b6>] ath10k_wmi_op_ep_tx_credits+0x16/0x40 [ath10k_core]
[<ffffffffa017d140>] ath10k_htc_rx+0x280/0x410 [ath10k_core]
[<ffffffffa01bcbf0>] ? ath10k_ce_completed_recv_next+0x60/0x80 [ath10k_pci]
[<ffffffffa01bc6ab>] ath10k_pci_ce_recv_data+0x11b/0x1d0 [ath10k_pci]
[<ffffffffa01bcf44>] ath10k_ce_per_engine_service+0x64/0xc0 [ath10k_pci]
[<ffffffffa01bcfc2>] ath10k_ce_per_engine_service_any+0x22/0x50 [ath10k_pci]
[<ffffffffa01bc4d0>] ath10k_pci_tasklet+0x30/0x90 [ath10k_pci]
[<ffffffff81055a55>] tasklet_action+0xc5/0x100
To prevent this make sure to release ar->data_lock
while calling to ath10k_wmi_beacon_send_ref_nowait().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The command logic shouldn't really care about
arvif structure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Ath10k driver sets wrong default key idx that results in
sending unicast frames with multicast key.
The reason for this behavior is that cached broadcast key
is installed for station MAC address on association. After
dot1x completes, unicast key is installed for station
MAC address. Default key idx is set to broadcast key id when
driver tries to send broadcast frame. This causes firmware
to use broadcast key id to transmit unicast frames to stations.
Used TX_USAGE flag to set default key for stations.
Added callback for setting unicast default idx which will be
invoked on every default key idx configuration.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently the adjusments made as part of perf_event_task_tick() use the
percpu rotation lists to iterate over any active PMU contexts, but these
are not used by the context rotation code, having been replaced by
separate (per-context) hrtimer callbacks. However, some manipulation of
the rotation lists (i.e. removal of contexts) has remained in
perf_rotate_context(). This leads to the following issues:
* Contexts are not always removed from the rotation lists. Removal of
PMUs which have been placed in rotation lists, but have not been
removed by a hrtimer callback can result in corruption of the rotation
lists (when memory backing the context is freed).
This has been observed to result in hangs when PMU drivers built as
modules are inserted and removed around the creation of events for
said PMUs.
* Contexts which do not require rotation may be removed from the
rotation lists as a result of a hrtimer, and will not be considered by
the unthrottling code in perf_event_task_tick.
This patch fixes the issue by updating the rotation ist when events are
scheduled in/out, ensuring that each rotation list stays in sync with
the HW state. As each event holds a refcount on the module of its PMU,
this ensures that when a PMU module is unloaded none of its CPU contexts
can be in a rotation list. By maintaining a list of perf_event_contexts
rather than perf_event_cpu_contexts, we don't need separate paths to
handle the cpu and task contexts, which also makes the code a little
simpler.
As the rotation_list variables are not used for rotation, these are
renamed to active_ctx_list, which better matches their current function.
perf_pmu_rotate_{start,stop} are renamed to
perf_pmu_ctx_{activate,deactivate}.
Reported-by: Johannes Jensen <johannes.jensen@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Will Deacon <Will.Deacon@arm.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20150129134511.GR17721@leverpostej
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When initialising an event, perf_init_event will call try_module_get() to
ensure that the PMU's module cannot be removed for the lifetime of the
event, with __free_event() dropping the reference when the event is
finally destroyed. If something fails after the event has been
initialised, but before the event is installed, perf_event_alloc will
drop the reference on the module.
However, if we fail to initialise an event for some reason (e.g. we ask
an uncore PMU to perform sampling, and it refuses to initialise the
event), we do not drop the refcount. If we try to open such a bogus
event without a precise IDR type, we will loop over each PMU in the pmus
list, incrementing each of their refcounts without decrementing them.
This patch adds a module_put when pmu->event_init(event) fails, ensuring
that the refcounts are balanced in failure cases. As the innards of the
precise and search based initialisation look very similar, this logic is
hoisted out into a new helper function. While the early return for the
failed try_module_get is removed from the search case, this is handled
by the remaining return when ret is not -ENOENT.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1420642611-22667-1-git-send-email-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Currently we flag available data (via poll syscall) on perf fd with
POLL_IN macro, which is normally used for SIGIO interface.
We've been lucky, because POLLIN (0x1) is subset of POLL_IN (0x20001)
and sys_poll (do_pollfd function) cut the extra bit out (0x20000).
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1422467678-22341-1-git-send-email-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
So what I suspect; but I'm in zombie mode today it seems; is that while
I initially thought that it was impossible for ctx to change when
refcount dropped to 0, I now suspect its possible.
Note that until perf_remove_from_context() the event is still active and
visible on the lists. So a concurrent sys_perf_event_open() from another
task into this task can race.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Stephane Eranian <eranian@gmail.com>
Cc: mark.rutland@arm.com
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20150129134434.GB26304@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Jiri reported triggering the new WARN_ON_ONCE in event_sched_out over
the weekend:
event_sched_out.isra.79+0x2b9/0x2d0
group_sched_out+0x69/0xc0
ctx_sched_out+0x106/0x130
task_ctx_sched_out+0x37/0x70
__perf_install_in_context+0x70/0x1a0
remote_function+0x48/0x60
generic_exec_single+0x15b/0x1d0
smp_call_function_single+0x67/0xa0
task_function_call+0x53/0x80
perf_install_in_context+0x8b/0x110
I think the below should cure this; if we install a group leader it
will iterate the (still intact) group list and find its siblings and
try and install those too -- even though those still have the old
event->ctx -- in the new ctx.
Upon installing the first group sibling we'd try and schedule out the
group and trigger the above warn.
Fix this by installing the group leader last, installing siblings
would have no effect, they're not reachable through the group lists
and therefore we don't schedule them.
Also delay resetting the state until we're absolutely sure the events
are quiescent.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Reported-by: vincent.weaver@maine.edu
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20150126162639.GA21418@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There have been a few reported issues wrt. the lack of locking around
changing event->ctx. This patch tries to address those.
It avoids the whole rwsem thing; and while it appears to work, please
give it some thought in review.
What I did fail at is sensible runtime checks on the use of
event->ctx, the RCU use makes it very hard.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20150123125834.209535886@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add a few WARN()s to catch things that should never happen.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20150123125834.150481799@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Vladislav Yasevich says:
====================
Restore UFO support to virtio_net devices
commit 3d0ad09412ffe00c9afa201d01effdb6023d09b4
Author: Ben Hutchings <ben@decadent.org.uk>
Date: Thu Oct 30 18:27:12 2014 +0000
drivers/net: Disable UFO through virtio
Turned off UFO support to virtio-net based devices due to issues
with IPv6 fragment id generation for UFO packets. The issue
was that IPv6 UFO/GSO implementation expects the fragment id
to be supplied in skb_shinfo(). However, for packets generated
by the VMs, the fragment id is not supplied which causes all
IPv6 fragments to have the id of 0.
The problem is that turning off UFO support on tap/macvtap
as well as virtio devices caused issues with migrations.
Migrations would fail when moving a vm from a kernel supporting
expecting UFO to work to the newer kernels that disabled UFO.
This series provides a partial solution to address the migration
issue. The series allows us to track whether skb_shinfo()->ip6_frag_id
has been set by treating value of 0 as unset.
This lets GSO code to generate fragment ids if they are necessary
(ex: packet was generated by VM or packet socket).
Since v3:
- Resolved build issue when IPv6 is a module.
- Removed trailing white space.
Since v2:
- Rebase and rebuild to make sure everything works. No changes
to the patches were done.
Since v1:
- Removed the skb bit and use value of 0 as tracker.
- Used Eric's suggestion to set fragment id as 0x80000000 if id
generation procedure yeilded a 0 result.
- Consolidated ipv6 id genration code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3d0ad09412ffe00c9afa201d01effdb6023d09b4.
Now that GSO functionality can correctly track if the fragment
id has been selected and select a fragment id if necessary,
we can re-enable UFO on tap/macvap and virtio devices.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 5188cd44c55db3e92cd9e77a40b5baa7ed4340f7.
Now that GSO layer can track if fragment id has been selected
and can allocate one if necessary, we don't need to do this in
tap and macvtap. This reverts most of the code and only keeps
the new ipv6 fragment id generation function that is still needed.
Fixes: 3d0ad09412ff (drivers/net: Disable UFO through virtio)
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the IPv6 fragment id has not been set and we perform
fragmentation due to UFO, select a new fragment id.
We now consider a fragment id of 0 as unset and if id selection
process returns 0 (after all the pertrubations), we set it to
0x80000000, thus giving us ample space not to create collisions
with the next packet we may have to fragment.
When doing UFO integrity checking, we also select the
fragment id if it has not be set yet. This is stored into
the skb_shinfo() thus allowing UFO to function correclty.
This patch also removes duplicate fragment id generation code
and moves ipv6_select_ident() into the header as it may be
used during GSO.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We explicitly mark the task running after returning from
a __rt_mutex_slowlock() call, which does the actual sleeping
via wait-wake-trylocking. As such, this patch does two things:
(1) refactors the code so that setting current to TASK_RUNNING
is done by __rt_mutex_slowlock(), and not by the callers. The
downside to this is that it becomes a bit unclear when at what
point we block. As such I've added a comment that the task
blocks when calling __rt_mutex_slowlock() so readers can figure
out when it is running again.
(2) relaxes setting current's state through __set_current_state(),
instead of it's more expensive barrier alternative. There was no
need for the implied barrier as we're obviously not planning on
blocking.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1422857784.18096.1.camel@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Call __set_task_state() instead of assigning the new state
directly. These interfaces also aid CONFIG_DEBUG_ATOMIC_SLEEP
environments, keeping track of who last changed the state.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1422257769-14083-2-git-send-email-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
