| Age | Commit message (Collapse) | Author |
|---|
|
When receiving an interface activation notification, if
the RF interface is NCI_RF_INTERFACE_NFCEE_DIRECT, we
need to ignore the following parameters and change the NCI
state machine to NCI_LISTEN_ACTIVE. According to the NCI
specification, the parameters should be 0 and shall be
ignored.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The NFCC sends an NCI_OP_RF_NFCEE_ACTION_NTF notification
to the host (DH) to let it know that for example an RF
transaction with a payment reader is done.
For now the notification handler is empty.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFC_EVT_TRANSACTION is sent through netlink in order for a
specific application running on a secure element to notify
userspace of an event. Typically the secure element application
counterpart on the host could interpret that event and act
upon it.
Forwarded information contains:
- SE host generating the event
- Application IDentifier doing the operation
- Applications parameters
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The st21nfcb chipset has 3 SWP (Single Wire Protocol) lines and
supports up to 3 secure elements (UICC/eSE and µSD in the future).
Some st21nfcb firmware does not support the nci command
nci_nfcee_mode_set(NCI_NFCEE_DISABLE). For this reason, we assume
2 secures elements are always present (UICC and eSE).
They will be added to the SE list once successfully activated and
they will be available only after running through enable_se
handler or when the poll in listen mode is started.
During initialization, the white_list will be always set assuming
both UICC & eSE are present.
On eSE activation, the ATR bytes are fetched to build the command
exchange timeout.
The se_io hook will allow to transfer data over SWP. 2 kind of
events may appear data is sent over:
- ST21NFCB_EVT_TRANSMIT_DATA when receiving an apdu answer
- ST21NFCB_EVT_WTX_REQUEST when the secure element needs more time
than expected to process a command. If this timeout expires, we
send a software reset, and then a hardware one if it still fails.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
According to the NCI specification, one can use HCI over NCI
to talk with specific NFCEE. The HCI network is viewed as one
logical NFCEE.
This is needed to support secure element running HCI only
firmwares embedded on an NCI capable chipset, like e.g. the
st21nfcb.
There is some duplication between this piece of code and the
HCI core code, but the latter would need to be abstracted even
more to be able to use NCI as a logical transport for HCP packets.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to communicate with an NFCEE, we need to open a logical
connection to it, by sending the NCI_OP_CORE_CONN_CREATE_CMD
command to the NFCC. It's left up to the drivers to decide when
to close an already opened logical connection.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFCEEs can be enabled or disabled by sending the
NCI_OP_NFCEE_MODE_SET_CMD command to the NFCC. This patch
provides an API for drivers to enable and disable e.g. their
NCI discoveredd secure elements.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFCEEs (NFC Execution Environment) have to be explicitly
discovered by sending the NCI_OP_NFCEE_DISCOVER_CMD
command. The NFCC will respond to this command by telling
us how many NFCEEs are connected to it. Then the NFCC sends
a notification command for each and every NFCEE connected.
Here we implement support for sending
NCI_OP_NFCEE_DISCOVER_CMD command, receiving the response
and the potential notifications.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add NFCEE NCI constant for:
- NFCEE Interface/Protocols
- Destination type
- Destination-specific parameters type
- NFCEE Discovery Action
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current NCI core only support the RF static connection.
For other NFC features such as Secure Element communication, we
may need to create logical connections to the NFCEE (Execution
Environment.
In order to track each logical connection ID dynamically, we add a
linked list of connection info pointers to the nci_dev structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
* pci/host-generic:
of/pci: Free resources on failure in of_pci_get_host_bridge_resources()
* pci/host-versatile:
PCI: versatile: Add DT-based ARM Versatile PB PCIe host driver
ARM: dts: versatile: add PCI controller binding
PCI: versatile: Add DT docs for ARM Versatile PB PCIe driver
|
|
* pci/config:
PCI: xilinx: Convert to use generic config accessors
PCI: xgene: Convert to use generic config accessors
PCI: tegra: Convert to use generic config accessors
PCI: rcar: Convert to use generic config accessors
PCI: generic: Convert to use generic config accessors
powerpc/powermac: Convert PCI to use generic config accessors
powerpc/fsl_pci: Convert PCI to use generic config accessors
ARM: ks8695: Convert PCI to use generic config accessors
ARM: sa1100: Convert PCI to use generic config accessors
ARM: integrator: Convert PCI to use generic config accessors
ARM: cns3xxx: Convert PCI to use generic config accessors
PCI: Add generic config accessors
powerpc/PCI: Add struct pci_ops member names to initialization
mn10300/PCI: Add struct pci_ops member names to initialization
MIPS: PCI: Add struct pci_ops member names to initialization
frv/PCI: Add struct pci_ops member names to initialization
|
|
Move the check for spi->bits_per_word
before allocation, to avoid memory leak.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sh-msiof of frequency dividing does not perform the calculation, driver have
to manage setting value in the table. It is not possible to set frequency
dividing value close to the actual data in this way. This changes from
frequency dividing of table management to setting by calculation.
This driver is able to set a value close to the actual data.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of calling device_create_file() manually, assign the static
attribute group entries at the device registration. This simplifies
the error handling and avoids the possible races.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of calling device_create_file() manually after the device
registration, put all in attribute groups and filter the unwanted ones
via is_visible callback. This not only simplifies the code but also
avoids the possible race between the device registration and sysfs
registration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
RTL2830 demod integrated to RTL2831U has PID filter. PID filtering
is provided by rtl2830 demod driver. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The SPI_IOC_MESSAGE(n) ioctl commands' argument points to an array of n
struct spi_ioc_transfer elements. The spidev's compat_ioctl handler
just converts this pointer and passes it on to the unlocked_ioctl
handler to process it.
The tx_buf and rx_buf members of struct spi_ioc_transfer are of type
__u64 and hold pointer values. A 32-bit userspace application running
in a 64-bit kernel might not have widened the 32-bit pointers correctly
for the kernel. The application might have sign-extended the pointer to
when the kernel expects it to be zero-extended, or vice versa, leading
to an -EFAULT being returned by spidev_message() if the widened pointer
is invalid.
Handle the SPI_IOC_MESSAGE(n) ioctl commands specially in the
compat_ioctl handler, calling new function spidev_compat_ioctl_message()
to handle them. This processes them in the same way as the
unlocked_ioctl handler except that it uses compat_ptr() to convert the
tx_buf and rx_buf members of each struct spi_ioc_transfer element.
To save code, factor out part of the unlocked_ioctl handler into a new
function spidev_get_ioc_message(). This checks the ioctl command code
is a valid SPI_IOC_MESSAGE(n), determines n and copies the array of n
struct spi_ioc_transfer elements from userspace into dynamically
allocated memory, returning either a pointer to the memory, an
ERR_PTR(-err) value, or NULL (for SPI_IOC_MESSAGE(0)).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Implement PID filter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Change legacy DVBv3 read SNR to return values calculated by DVBv5
statistics.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Change legacy DVBv3 read BER to return values calculated by DVBv5
statistics.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Change legacy DVBv3 signal strength to return values calculated by
DVBv5 statistics.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
DVBv5 BER.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Estimate signal strength from IF AGC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
DVBv5 CNR.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Trivial changes proposed by checkpatch.pl and some more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Remove internal config and use configuration values directly from
the platform data.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Pass correct device for dev_foo() logging in order to print logs
correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
As a I2C driver struct i2c_client is top level structure representing
the driver. Use it as parameter to carry all needed information for
each function in order to simplify things.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use name 'dev' for device state instance as it is more common and
also one letter shorter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Remove legacy DVB binding as all users are using I2C binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
rtl2830 driver supports now I2C model too. Start using it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Convert driver to kernel I2C model. Old DVB proprietary model is
still left there also.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Top level pointer on USB probe is struct usb_interface *. Add that
pointer to struct dvb_usb_device that drivers could use it, for
dev_* logging and more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Added entry in sst driver to support rt5645 codec
for intel Braswell platform.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current Renesas R-Car sound driver doesn't call
snd_soc_unregiter_component/platform() in .remove.
This patch call these functions.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: Bui Duc Phuc <bd-phuc@jinso.co.jp>
Reported-by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current Renesas R-Car sound driver is using snd_ctl_xxx()
functions, but it didn't call snd_ctl free_one() / snd_ctl_remove().
This patch call these functions.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: Bui Duc Phuc <bd-phuc@jinso.co.jp>
Reported-by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
One of the McASP instances in DM646x line of DMSoC only supports DIT mode.
This means that the given IP does not have support for rx and all the rx
related resources are missing, like irq and DMA request.
The driver should not fail if any or all of the RX resource is missing
when the op_mode is set to DIT mode.
Since RX is not possible in DIT mode, we can just ignore the rx resources
when the McASP is used in DIT mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On DA830 devices McASP0,1 and 2 shares a single combined interrupt request
line.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no need for them to be included.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The machine driver has no business with the underlying dma.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
-9.ucode doesn't know the command SHARED_MEM_CFG yet.
Fixes: 04fd2c28226f ("iwlwifi: mvm: add rxf and txf to dump data")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Using seq_putc to print a single character saves at least a strlen()
call and a memory access, and may also give a small .text reduction.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Consecutive seq_puts calls with literal strings may be replaced by a
single call, saving a little .text.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Using seq_printf to print a simple string is a lot more expensive than
it needs to be, since seq_puts exists. Replace seq_printf with
seq_puts when possible.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Using seq_printf to print a simple string is a lot more expensive than
it needs to be, since seq_puts exists. Replace seq_printf with
seq_puts when possible.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Using seq_printf to print a simple string is a lot more expensive than
it needs to be, since seq_puts exists. Replace seq_printf with
seq_puts when possible.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The macro SPRINTF doesn't save a lot of typing or make the code more
readable, and depending on a specific identifier (m) in the
surrounding scope is generally frowned upon. Nuke it.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The 'data_dir' variable is not used in sg_common_write(), hence
remove this variable.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Suggested-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Reviewed-by: Kevin Barnett <Kevin.Barnett@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
