summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-12-07media: ccs-pll: Remove parallel bus supportSakari Ailus
The parallel bus PLL calculation has no users. Remove it. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: End search if there are no better values availableSakari Ailus
The VT divisor search can be ended if we've already found the value that corresponds exactly the total divisor, as there are no better (lower) values available. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Use correct VT divisor for calculating VT SYS divisorSakari Ailus
Use the correct video timing divisor to calculate the SYS divisor. Instead of the current value, the minimum was used. This could have resulted in a too low SYS divisor. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Split limits and PLL configuration into front and back partsSakari Ailus
The CCS spec supports a lot of variation in the PLL. Split the PLL in front and back parts to better prepare for supporting it. Also use CCS compliant naming for IP and OP PLL frequencies (i.e. include "clk" in the name). Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs-pll: Don't use div_u64 to divide a 32-bit numberSakari Ailus
pll->pll_op_clk_freq is a 32-bit number. It does not need div_u64 to divide it. Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07MAINTAINERS: add a limited ARM and ARM64 SoC entryKrzysztof Kozlowski
It is expected for ARM and ARM64 SoC related code to go through sub-architecture maintainers. Their addresses were therefore not documented to push patch traffic through sub-architecture maintainers. However when patches touch generic code, e.g. multi_v7_defconfig, the patch might not be picked up by them and instead should go to the SoC maintainers - Arnd and Olof. Add a minimal maintainer's entry for SoC covering only Makefile, so it will not appear on most of submissions (except new devicetree boards). It will though serve as a documentation and reference for cases when submitter does not know where to send his SoC-related patches. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201201211516.24921-2-krzk@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07MAINTAINERS: correct SoC Git address (formerly: arm-soc)Krzysztof Kozlowski
The SoC Git was moved from arm/arm-soc.git to soc/soc.git. Correct the ARM Sub-architectures entry. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201201211516.24921-1-krzk@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07ARM: keystone: remove SECTION_SIZE_BITS/MAX_PHYSMEM_BITSArnd Bergmann
These definitions are evidently left over from the days when sparsemem settings were platform specific. This was no longer the case when the platform got merged. There was no warning in the past, but now the asm/sparsemem.h header ends up being included indirectly, causing this warning: In file included from /git/arm-soc/arch/arm/mach-keystone/keystone.c:24: arch/arm/mach-keystone/memory.h:10:9: warning: 'SECTION_SIZE_BITS' macro redefined [-Wmacro-redefined] #define SECTION_SIZE_BITS 34 ^ arch/arm/include/asm/sparsemem.h:23:9: note: previous definition is here #define SECTION_SIZE_BITS 28 ^ Clearly the definitions never had any effect here, so remove them. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20201203231847.1484900-1-arnd@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07Merge tag 'imx-fixes-5.10-5' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes i.MX fixes for 5.10, round 5: - Fix a regression on SoC revision detection with ANATOP, that is introduced by commit 4a4fb66119eb ("ARM: imx: Add missing of_node_put()"). - Drop PAD_GPIO_6 from imx6qdl-wandboard ENET pin group, as the pin is used by camera sensor now. - Fix I2C3_SCL pinmux on imx6qdl-kontron-samx6i board, so that SoM EEPROM can be accessed. * tag 'imx-fixes-5.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: dts: imx6qdl-kontron-samx6i: fix I2C_PM scl pin ARM: dts: imx6qdl-wandboard-revd1: Remove PAD_GPIO_6 from enetgrp ARM: imx: Use correct SRC base address Link: https://lore.kernel.org/r/20201201091820.GW4072@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07Merge tag 'sunxi-fixes-for-5.10-2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes A few more RGMII-ID fixes, and a bunch of other more random fixes * tag 'sunxi-fixes-for-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: ARM: dts: sun7i: pcduino3-nano: enable RGMII RX/TX delay on PHY ARM: dts: sun8i: v3s: fix GIC node memory range ARM: dts: sun8i: v40: bananapi-m2-berry: Fix ethernet node ARM: dts: sun8i: r40: bananapi-m2-berry: Fix dcdc1 regulator ARM: dts: sun7i: bananapi: Enable RGMII RX/TX delay on Ethernet PHY ARM: dts: s3: pinecube: align compatible property to other S3 boards ARM: sunxi: Add machine match for the Allwinner V3 SoC arm64: dts: allwinner: h6: orangepi-one-plus: Fix ethernet Link: https://lore.kernel.org/r/1280f1de-1b6d-4cc2-8448-e5a9096a41e8.lettre@localhost Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-12-07media: dt-bindings: schema indentation fixesRob Herring
Fix a few new indentation warnings found with yamllint (now integrated into the checks). Cc: Ricardo Ribalda <ribalda@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # For adv7604 Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: vivid: fix 'disconnect' error injectionHans Verkuil
The 'disconnect' error injection functionality suffered from bit rot. New device nodes were added without updating vivid_user_gen_s_ctrl(), so that function had to be updated for the new device nodes. Also, vivid didn't check if specific device nodes were actually ever created, so the vivid_is_last_user() would fail on that (it would return true instead of false in that case). Finally, selecting Disconnect, then unbind the vivid driver would fail since the remove() would think that the device nodes were already unregistered. Keep track of whether disconnect was pressed and re-register the device nodes in remove() before doing the real unregister. [hverkuil: unsigned uses -> unsigned int uses] Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: rcar-vin: Mask VNCSI_IFMD registerJacopo Mondi
The VNCSI_IFMD register controls the data expansion mode and the channel routing between the CSI-2 receivers and VIN instances. According to the chip manual revision 2.20 not all fields are available for all the SoCs: - V3M, V3H and E3 do not support the DES1 field has they do not feature a CSI20 receiver. - D3 only supports parallel input, and the whole register shall always be written as 0. Inspect the per-SoC channel routing table where the available CSI-2 instances are reported and configure VNCSI_IFMD accordingly. This patch supports this BSP change commit: https://github.com/renesas-rcar/linux-bsp/commit/f54697394457 ("media: rcar-vin: Fix VnCSI_IFMD register access for r8a77990") [hverkuil: replace BSP commit ID with BSP URL] Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Suggested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: MAINTAINERS: Add myself as maintainer of the Amlogic GE2D driverNeil Armstrong
Add new entry to MAINTAINERS. [hverkuil: added changelog] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: meson: Add M2M driver for the Amlogic GE2D Accelerator UnitNeil Armstrong
The GE2D is a 2D accelerator with various features like configurable blitter with alpha blending, frame rotation, scaling, format conversion and colorspace conversion. The driver implements a Memory2Memory VB2 V4L2 streaming device permitting: - 0, 90, 180, 270deg rotation - horizontal/vertical flipping - source cropping - destination compositing - 32bit/24bit/16bit format conversion This adds the support for the GE2D version found in the AXG SoCs Family. The missing features are: - Source scaling - Colorspace conversion - Advanced alpha blending & blitting options Is passes v4l2-compliance: SHA: ea16a7ef13a902793a5c2626b0cefc4d956147f3, 64 bits, 64-bit time_t [hverkuil: add missing linux/bitfield.h include] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: dt-bindings: media: Add bindings for the Amlogic GE2D Accelerator UnitNeil Armstrong
The GE2D is a 2D accelerator with various features like configurable blitter with alpha blending, frame rotation, scaling, format conversion and colorspace conversion. This adds the bindings for the GE2D version found in the AXG SoCs Family. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: cedrus: Make VP8 codec as capabilityJernej Skrabec
Commit 31d9b9ef8564 ("media: cedrus: Register all codecs as capability") makes separate capability flags for each codec. However, VP8 codec was merged at the same time as mentioned patch, so there is no capability flag for it. This patch adds capability flag for VP8 and enables it for all variants except for V3s. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: gspca: Fix memory leak in probeAlan Stern
The gspca driver leaks memory when a probe fails. gspca_dev_probe2() calls v4l2_device_register(), which takes a reference to the underlying device node (in this case, a USB interface). But the failure pathway neglects to call v4l2_device_unregister(), the routine responsible for dropping this reference. Consequently the memory for the USB interface and its device never gets released. This patch adds the missing function call. Reported-and-tested-by: syzbot+44e64397bd81d5e84cba@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Move all planar YUV formats to common fileLaurent Pinchart
Planar pixel formats are documented in separate files. This duplicates information, as those formats share comon traits. Consolidate them in a single file and summarize their descriptions in a single table. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Move all semi-planar YUV formats to common fileLaurent Pinchart
Semi-planar pixel formats are documented in separate files. This duplicates information, as those formats share comon traits. Consolidate them in a single file and summarize their descriptions in a single table. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Move all luma-only YUV formats to common fileLaurent Pinchart
Luma-only pixel formats are documented in separate files. This duplicates information, as those formats share comon traits. Consolidate them in a single file and describe them in a single table. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-packed-yuv: Clarify naming scheme for 4:4:4 formatsLaurent Pinchart
Document the naming scheme for the existing packed YUV 4:4:4 formats, as previously done for the RGB formats. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-packed-yuv: Express 4:4:4 formats in a more compact wayLaurent Pinchart
The 4:4:4 packed YUV formats are documented with a bit-level representation, which creates a wide table. Switch to a byte-oriented representation to make it more compact. This prepares for the addition of formats with more than 8 bits per component, that would make the table way too wide. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-packed-yuv: Fill padding bits with 'X'Laurent Pinchart
The padding bits are left blank, which look weird in the XYUV format, and, worse, may lead to the VUYX format to be understand as consuming 3 bytes per pixel. Add 'X' for padding bits as we do for RGB formats. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Move all packed YUV formats to common fileLaurent Pinchart
The pixfmt-packed-yuv.rst file documents packed YUV 4:4:4 formats, but is titled generically as "Packed YUV formats". 4:2:2 and 4:1:1 packed YUV formats are documented in separate files, which can be confusing. Group all packed YUV formats in pixfmt-packed-yuv.rst, which allows documenting the 4:2:2 formats in a more concise way. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-yuv: Document subsampling in more detailsLaurent Pinchart
Document YUV subsampling, including chroma spatial siting, and replace the siting examples in individual formats by references to the common documentation. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Replace '-' with 'X' to denote paddingLaurent Pinchart
Using '-' to represent padding bits and bytes make text and tables more difficult to read. Use 'x' and 'X' instead. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Make 8 bits per component table more compactLaurent Pinchart
All formats using 8 bits per component can be described with a byte granularity instead of a bit granularity without loss of precision. This makes the corresponding table more compact and easier to read. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Clarify naming scheme for RGB formatsLaurent Pinchart
The naming scheme for the RGB pixel formats has been developed organically, and isn't consistent between formats using less than 8 bits per pixels (mostly stored in 1 or 2 bytes per pixel, except for RGB666 that uses 4 bytes per pixel) and formats with 8 bits per pixel (stored in 3 or 4 bytes). For the latter category, the names use a components order convention that is the opposite of the first category, and the opposite of DRM pixel formats. This has led to lots of confusion in the past, and would really benefit from being explained more precisely. Do so, which also prepares for the addition of additional RGB pixels formats. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Add title for deprecated formatsLaurent Pinchart
Improve readability of the documentation by adding a section title for the deprecated formats. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: doc: pixfmt-rgb: Remove layout table for packed RGB formatsLaurent Pinchart
The packed RGB formats documentation includes a layout table without any context. This doesn't bring much useful information, and is confusing at best. Remove it. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: videodev2.h: Move HM12 format to YUV semi-planar sectionLaurent Pinchart
V4L2_PIX_FMT_HM12 is a YUV semi-planar macro-block format. Move it from the packed YUV formats section where it was misplaced to the YUV semi-planar formats section. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: videodev2.h: Move HI240 format to vendor-specific sectionLaurent Pinchart
V4L2_PIX_FMT_HI240 is a 8-bit dithered RGB format specific to BTTV. Move it from the packed YUV formats section where it was misplaced to the vendor-specific formats section. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: videodev2.h: Remove unneeded comment about 4CC valueLaurent Pinchart
The V4L2_PIX_FMT_BGRA444 format has a comment that explains why its 4CC value is GA12. This explains the development history and isn't of much interest to readers, it should have been part of a commit message instead. Drop the comment, anyone interested in history can turn to git. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs: Fix return value from probeSakari Ailus
rval wasn't set, resulting in probe returning zero instead of an error. Fixes: de10c1619c48 ("[media] smiapp: Get clock rate if it's not available through DT") Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: ccs: avoid printing an uninitialized variableArnd Bergmann
There is no intialization for the 'reg' variable, so printing it produces undefined behavior as well as a compile-time warning: drivers/media/i2c/ccs/ccs-core.c:314:49: error: variable 'reg' is uninitialized when used here [-Werror,-Wuninitialized] "0x%8.8x %s pixels: %d %s (pixelcode %u)\n", reg, Remove the variable and stop printing it. Fixes: fd9065812c7b ("media: smiapp: Obtain frame descriptor from CCS limits") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: i2c: fix an uninitialized error codeArnd Bergmann
Clang points out that the error handling in ov02a10_s_stream() is broken, and just returns a random error code: drivers/media/i2c/ov02a10.c:537:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized] if (ov02a10->streaming == on) ^~~~~~~~~~~~~~~~~~~~~~~~ drivers/media/i2c/ov02a10.c:568:9: note: uninitialized use occurs here return ret; ^~~ drivers/media/i2c/ov02a10.c:537:2: note: remove the 'if' if its condition is always false if (ov02a10->streaming == on) ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ If streaming is already on, leave it that way and return success. Suggested-by: Dongchun Zhu <dongchun.zhu@mediatek.com> Fixes: 91807efbe8ec ("media: i2c: add OV02A10 image sensor driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: Revert "media: dt-bindings: media: Use OF graph schema"Sakari Ailus
This reverts commit f61eb7bc9256aeb173d2d730f59cdd569d261c52. While aligning with the OF graph schema will be done for the media DT bindings, this patch got merged a little too hastily. Revert it for now. Suggested-by: Rob Herring <robh@kernel.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07media: rc: add keymap for pine64 remoteJonas Karlman
Add a keymap for the pine64 IR remote [0]. The mouse key has been mapped to KEY_EPG to provide a more useful remote. [0] http://files.pine64.org/doc/Pine%20A64%20Schematic/remote-wit-logo.jpg Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-12-07x86/alternative: Update text_poke_bp() kernel-doc commentQiujun Huang
Update kernel-doc parameter name after c3d6324f841b ("x86/alternatives: Teach text_poke_bp() to emulate instructions") changed the last parameter from @handler to @emulate. [ bp: Make commit message more precise. ] Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20201203145020.2441-1-hqjagain@gmail.com
2020-12-07EDAC/mv64x60: Remove orphan mv64x60 driverMichael Ellerman
The mv64x60 EDAC driver depends on CONFIG_MV64X60. But that symbol is not user-selectable, and the last code that selected it was removed with the C2K board support in 2018, see: 92c8c16f3457 ("powerpc/embedded6xx: Remove C2K board support") That means the driver is now dead code, so remove it. Suggested-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20201207040253.628528-1-mpe@ellerman.id.au
2020-12-07EDAC/aspeed: Add support for AST2400 and AST2600Troy Lee
Add AST2400 and AST2600 EDAC driver support. Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Stefan Schaeckeler <sschaeck@cisco.com> Link: https://lkml.kernel.org/r/20201207090013.14145-3-troy_lee@aspeedtech.com
2020-12-07ARM: dts: aspeed: Add AST2600 EDAC into common devicetreeTroy Lee
Add Aspeed AST2600 EDAC node into the common devicetree. Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lkml.kernel.org/r/20201207090013.14145-2-troy_lee@aspeedtech.com
2020-12-07dt-bindings: edac: aspeed-sdram-edac: Add ast2400/ast2600 supportTroy Lee
Add Aspeed AST2400 and AST2600 binding for the Aspeed EDAC driver. Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Joel Stanley <joel@jms.id.au> Link: https://lkml.kernel.org/r/20201207090013.14145-1-troy_lee@aspeedtech.com
2020-12-07iommu/amd: Set DTE[IntTabLen] to represent 512 IRTEsSuravee Suthikulpanit
According to the AMD IOMMU spec, the commit 73db2fc595f3 ("iommu/amd: Increase interrupt remapping table limit to 512 entries") also requires the interrupt table length (IntTabLen) to be set to 9 (power of 2) in the device table mapping entry (DTE). Fixes: 73db2fc595f3 ("iommu/amd: Increase interrupt remapping table limit to 512 entries") Reported-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20201207091920.3052-1-suravee.suthikulpanit@amd.com Signed-off-by: Will Deacon <will@kernel.org>
2020-12-07MAINTAINERS: Update m68k Mac entryFinn Thain
Two files under drivers/macintosh are actually m68k-only. I think that patches for these files should be reviewed in the appropriate forum and merged via the appropriate tree, rather than falling to the powerpc maintainers to deal with. Update the "M68K ON APPLE MACINTOSH" section accordingly. Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Joshua Thompson <funaho@jurai.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-m68k@lists.linux-m68k.org Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/fbac2cd8632bb719f48cd1368910abd310548a0e.1607139987.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2020-12-07macintosh/adb-iop: Send correct poll commandFinn Thain
The behaviour of the IOP firmware is not well documented but we do know that IOP message reply data can be used to issue new ADB commands. Use the message reply to better control autopoll behaviour by sending a Talk Register 0 command after every ADB response, not unlike the algorithm in the via-macii driver. This poll command is addressed to that device which last received a Talk command (explicit or otherwise). Cc: Joshua Thompson <funaho@jurai.org> Fixes: 32226e817043 ("macintosh/adb-iop: Implement idle -> sending state transition") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Link: https://lore.kernel.org/r/58bba4310da4c29b068345a4b36af8a531397ff7.1605847196.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2020-12-07macintosh/adb-iop: Always wait for reply message from IOPFinn Thain
A recent patch incorrectly altered the adb-iop state machine behaviour and introduced a regression that can appear intermittently as a malfunctioning ADB input device. This seems to be caused when reply packets from different ADB commands become mixed up, especially during the adb bus scan. Fix this by unconditionally entering the awaiting_reply state after sending an explicit command, even when the ADB command won't generate a reply from the ADB device. It turns out that the IOP always generates reply messages, even when the ADB command does not produce a reply packet (e.g. ADB Listen command). So it's not really the ADB reply packets that are being mixed up, it's the IOP messages that enclose them. The bug goes like this: 1. CPU sends a message to the IOP, expecting no response because this message contains an ADB Listen command. The ADB command is now considered complete. 2. CPU sends a second message to the IOP, this time expecting a response because this message contains an ADB Talk command. This ADB command needs a reply before it can be completed. 3. adb-iop driver receives an IOP message and assumes that it relates to the Talk command. It's actually an empty one (with flags == ADB_IOP_EXPLICIT|ADB_IOP_TIMEOUT) for the previous command. The Talk command is now considered complete but it gets the wrong reply data. 4. adb-iop driver gets another IOP response message, which contains the actual reply data for the Talk command, but this is dropped (the driver is no longer in awaiting_reply state). Cc: Joshua Thompson <funaho@jurai.org> Fixes: e2954e5f727f ("macintosh/adb-iop: Implement sending -> idle state transition") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Link: https://lore.kernel.org/r/0f0a25855391e7eaa53a50f651aea0124e8525dd.1605847196.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2020-12-07udp: fix the proto value passed to ip_protocol_deliver_rcu for the segmentsXin Long
Guillaume noticed that: for segments udp_queue_rcv_one_skb() returns the proto, and it should pass "ret" unmodified to ip_protocol_deliver_rcu(). Otherwize, with a negtive value passed, it will underflow inet_protos. This can be reproduced with IPIP FOU: # ip fou add port 5555 ipproto 4 # ethtool -K eth1 rx-gro-list on Fixes: cf329aa42b66 ("udp: cope with UDP GRO packet misdirection") Reported-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-12-06net: hns3: remove a misused pragma packedHuazhong Tan
hclge_dbg_reg_info[] is defined as an array of packed structure accidentally. However, this array contains pointers, which are no longer aligned naturally, and cannot be relocated on PPC64. Hence, when compile-testing this driver on PPC64 with CONFIG_RELOCATABLE=y (e.g. PowerPC allyesconfig), there will be some warnings. Since each field in structure hclge_qos_pri_map_cmd and hclge_dbg_bitmap_cmd is type u8, the pragma packed is unnecessary for these two structures as well, so remove the pragma packed in hclge_debugfs.h to fix this issue, and this increases hclge_dbg_reg_info[] by 4 bytes per entry. Fixes: a582b78dfc33 ("net: hns3: code optimization for debugfs related to "dump reg"") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-12 14:26:40 +0000