| Age | Commit message (Collapse) | Author |
|---|
|
In case driver sent NACK to firmware on sync reset request, it will get
sync reset abort event while it didn't set sync reset requested mode.
Thus, on abort sync reset event handler, driver should check reset
requested is set before trying to stop sync reset poll.
Fixes: 7dd6df329d4c ("net/mlx5: Handle sync reset abort event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
TLS offload is not supported in switchdev mode.
Fixes: 7a9fb35e8c3a ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Device supports setting of a single fec mode at a time, enforce this
by bitmap_weight == 1. Input from fec command is in u32, avoid cast to
unsigned long and use bitmap_from_arr32 to populate bitmap safely.
Fixes: 4bd9d5070b92 ("net/mlx5e: Enforce setting of a single FEC mode")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
It looks as if the MAINTAINERS entries for the nfc mailing list
should be updated as I just got a "rejected" bounce from the nfc list.
-------
Your message to the Linux-nfc mailing-list was rejected for the following
reasons:
The message is not from a list member
-------
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maxim Mikityanskiy says:
====================
Fix use-after-free after the TLS device goes down and up
This small series fixes a use-after-free bug in the TLS offload code.
The first patch is a preparation for the second one, and the second is
the fix itself.
v2 changes:
Remove unneeded EXPORT_SYMBOL_GPL.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a netdev with active TLS offload goes down, tls_device_down is
called to stop the offload and tear down the TLS context. However, the
socket stays alive, and it still points to the TLS context, which is now
deallocated. If a netdev goes up, while the connection is still active,
and the data flow resumes after a number of TCP retransmissions, it will
lead to a use-after-free of the TLS context.
This commit addresses this bug by keeping the context alive until its
normal destruction, and implements the necessary fallbacks, so that the
connection can resume in software (non-offloaded) kTLS mode.
On the TX side tls_sw_fallback is used to encrypt all packets. The RX
side already has all the necessary fallbacks, because receiving
non-decrypted packets is supported. The thing needed on the RX side is
to block resync requests, which are normally produced after receiving
non-decrypted packets.
The necessary synchronization is implemented for a graceful teardown:
first the fallbacks are deployed, then the driver resources are released
(it used to be possible to have a tls_dev_resync after tls_dev_del).
A new flag called TLS_RX_DEV_DEGRADED is added to indicate the fallback
mode. It's used to skip the RX resync logic completely, as it becomes
useless, and some objects may be released (for example, resync_async,
which is allocated and freed by the driver).
Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RCU synchronization is guaranteed to finish in finite time, unlike a
busy loop that polls a flag. This patch is a preparation for the bugfix
in the next patch, where the same synchronize_net() call will also be
used to sync with the TX datapath.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'status'.
Eliminate the follow smatch warning:
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:3818 myri10ge_probe()
warn: missing error code 'status'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xuan Zhuo says:
====================
virtio-net: fix for build_skb()
The logic of this piece is really messy. Fortunately, my refactored patch can be
completed with a small amount of testing.
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of merge, the page passed into page_to_skb() may be a head
page, not the page where the current data is located. So when trying to
get the buf where the data is located, we should get buf based on
headroom instead of offset.
This patch solves this problem. But if you don't use this patch, the
original code can also run, because if the page is not the page of the
current data, the calculated tailroom will be less than 0, and will not
enter the logic of build_skb() . The significance of this patch is to
modify this logical problem, allowing more situations to use
build_skb().
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In merge mode, when xdp is enabled, if the headroom of buf is smaller
than virtnet_get_headroom(), xdp_linearize_page() will be called but the
variable of "headroom" is still 0, which leads to wrong logic after
entering page_to_skb().
[ 16.600944] BUG: unable to handle page fault for address: ffffecbfff7b43c8[ 16.602175] #PF: supervisor read access in kernel mode
[ 16.603350] #PF: error_code(0x0000) - not-present page
[ 16.604200] PGD 0 P4D 0
[ 16.604686] Oops: 0000 [#1] SMP PTI
[ 16.605306] CPU: 4 PID: 715 Comm: sh Tainted: G B 5.12.0+ #312
[ 16.606429] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/04
[ 16.608217] RIP: 0010:unmap_page_range+0x947/0xde0
[ 16.609014] Code: 00 00 08 00 48 83 f8 01 45 19 e4 41 f7 d4 41 83 e4 03 e9 a4 fd ff ff e8 b7 63 ed ff 4c 89 e0 48 c1 e0 065
[ 16.611863] RSP: 0018:ffffc90002503c58 EFLAGS: 00010286
[ 16.612720] RAX: ffffecbfff7b43c0 RBX: 00007f19f7203000 RCX: ffffffff812ff359
[ 16.613853] RDX: ffff888107778000 RSI: 0000000000000000 RDI: 0000000000000005
[ 16.614976] RBP: ffffea000425e000 R08: 0000000000000000 R09: 3030303030303030
[ 16.616124] R10: ffffffff82ed7d94 R11: 6637303030302052 R12: 7c00000afffded0f
[ 16.617276] R13: 0000000000000001 R14: ffff888119ee7010 R15: 00007f19f7202000
[ 16.618423] FS: 0000000000000000(0000) GS:ffff88842fd00000(0000) knlGS:0000000000000000
[ 16.619738] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 16.620670] CR2: ffffecbfff7b43c8 CR3: 0000000103220005 CR4: 0000000000370ee0
[ 16.621792] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 16.622920] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 16.624047] Call Trace:
[ 16.624525] ? release_pages+0x24d/0x730
[ 16.625209] unmap_single_vma+0xa9/0x130
[ 16.625885] unmap_vmas+0x76/0xf0
[ 16.626480] exit_mmap+0xa0/0x210
[ 16.627129] mmput+0x67/0x180
[ 16.627673] do_exit+0x3d1/0xf10
[ 16.628259] ? do_user_addr_fault+0x231/0x840
[ 16.629000] do_group_exit+0x53/0xd0
[ 16.629631] __x64_sys_exit_group+0x1d/0x20
[ 16.630354] do_syscall_64+0x3c/0x80
[ 16.630988] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 16.631828] RIP: 0033:0x7f1a043d0191
[ 16.632464] Code: Unable to access opcode bytes at RIP 0x7f1a043d0167.
[ 16.633502] RSP: 002b:00007ffe3d993308 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
[ 16.634737] RAX: ffffffffffffffda RBX: 00007f1a044c9490 RCX: 00007f1a043d0191
[ 16.635857] RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000000
[ 16.636986] RBP: 0000000000000000 R08: ffffffffffffff88 R09: 0000000000000001
[ 16.638120] R10: 0000000000000008 R11: 0000000000000246 R12: 00007f1a044c9490
[ 16.639245] R13: 0000000000000001 R14: 00007f1a044c9968 R15: 0000000000000000
[ 16.640408] Modules linked in:
[ 16.640958] CR2: ffffecbfff7b43c8
[ 16.641557] ---[ end trace bc4891c6ce46354c ]---
[ 16.642335] RIP: 0010:unmap_page_range+0x947/0xde0
[ 16.643135] Code: 00 00 08 00 48 83 f8 01 45 19 e4 41 f7 d4 41 83 e4 03 e9 a4 fd ff ff e8 b7 63 ed ff 4c 89 e0 48 c1 e0 065
[ 16.645983] RSP: 0018:ffffc90002503c58 EFLAGS: 00010286
[ 16.646845] RAX: ffffecbfff7b43c0 RBX: 00007f19f7203000 RCX: ffffffff812ff359
[ 16.647970] RDX: ffff888107778000 RSI: 0000000000000000 RDI: 0000000000000005
[ 16.649091] RBP: ffffea000425e000 R08: 0000000000000000 R09: 3030303030303030
[ 16.650250] R10: ffffffff82ed7d94 R11: 6637303030302052 R12: 7c00000afffded0f
[ 16.651394] R13: 0000000000000001 R14: ffff888119ee7010 R15: 00007f19f7202000
[ 16.652529] FS: 0000000000000000(0000) GS:ffff88842fd00000(0000) knlGS:0000000000000000
[ 16.653887] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 16.654841] CR2: ffffecbfff7b43c8 CR3: 0000000103220005 CR4: 0000000000370ee0
[ 16.655992] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 16.657150] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 16.658290] Kernel panic - not syncing: Fatal exception
[ 16.659613] Kernel Offset: disabled
[ 16.660234] ---[ end Kernel panic - not syncing: Fatal exception ]---
Fixes: fb32856b16ad ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the in-kernel mark setting by doing an additional
sk_dst_reset() which was introduced by commit 50254256f382 ("sock: Reset
dst when changing sk_mark via setsockopt"). The code is now shared to
avoid any further suprises when changing the socket mark value.
Fixes: 84d1c617402e ("net: sock: add sock_set_mark")
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using sub-VLANs in the range of 1-7, the resulting value from:
rx_vid = dsa_8021q_rx_vid_subvlan(ds, port, subvlan);
is wrong according to the description from tag_8021q.c:
| 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+-----------+-----+-----------------+-----------+-----------------------+
| DIR | SVL | SWITCH_ID | SUBVLAN | PORT |
+-----------+-----+-----------------+-----------+-----------------------+
For example, when ds->index == 0, port == 3 and subvlan == 1,
dsa_8021q_rx_vid_subvlan() returns 1027, same as it returns for
subvlan == 0, but it should have returned 1043.
This is because the low portion of the subvlan bits are not masked
properly when writing into the 12-bit VLAN value. They are masked into
bits 4:3, but they should be masked into bits 5:4.
Fixes: 3eaae1d05f2b ("net: dsa: tag_8021q: support up to 8 VLANs per port using sub-VLANs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b7f55d928e75557295c1ac280c291b738905b6fb.
As explained by Linus in [*], write faults on a mmap region are reads
from a filesysten point of view, so taking the inode glock exclusively
on write faults is incorrect.
Instead, when a page is marked writable, the .page_mkwrite vm operation
will be called, which is where the exclusive lock taking needs to
happen. I got this wrong because of a broken test case that made me
believe .page_mkwrite isn't getting called when it actually is.
[*] https://lore.kernel.org/lkml/CAHk-=wj8EWr_D65i4oRSj2FTbrc6RdNydNNCGxeabRnwtoU=3Q@mail.gmail.com/
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
Currently if __nfs4_proc_set_acl fails with NFS4ERR_BADOWNER it
re-enables the idmapper by clearing NFS_CAP_UIDGID_NOMAP before
retrying again. The NFS_CAP_UIDGID_NOMAP remains cleared even if
the retry fails. This causes problem for subsequent setattr
requests for v4 server that does not have idmapping configured.
This patch modifies nfs4_proc_set_acl to detect NFS4ERR_BADOWNER
and NFS4ERR_BADNAME and skips the retry, since the kernel isn't
involved in encoding the ACEs, and return -EINVAL.
Steps to reproduce the problem:
# mount -o vers=4.1,sec=sys server:/export/test /tmp/mnt
# touch /tmp/mnt/file1
# chown 99 /tmp/mnt/file1
# nfs4_setfacl -a A::unknown.user@xyz.com:wrtncy /tmp/mnt/file1
Failed setxattr operation: Invalid argument
# chown 99 /tmp/mnt/file1
chown: changing ownership of ‘/tmp/mnt/file1’: Invalid argument
# umount /tmp/mnt
# mount -o vers=4.1,sec=sys server:/export/test /tmp/mnt
# chown 99 /tmp/mnt/file1
#
v2: detect NFS4ERR_BADOWNER and NFS4ERR_BADNAME and skip retry
in nfs4_proc_set_acl.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
Commit ccf953d8f3d6 makes framebuffers which use deferred I/O stop
displaying updates after the first one. This is because the pages
handled by fb_defio no longer have a page_mapping(). That prevents
page_mkclean() from marking the PTEs as clean, and so writes are only
noticed the first time.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/YLZEhv0cpZp8uVE3@casper.infradead.org
|
|
Perf tool errors out with the latest event list for the Ice Lake server.
event syntax error: 'unc_m2m_imc_reads.to_pmm'
\___ value too big for format, maximum is 255
The same as the Snow Ridge server, the M2M uncore unit in the Ice Lake
server has the unit mask extension field as well.
Fixes: 2b3b76b5ec67 ("perf/x86/intel/uncore: Add Ice Lake server uncore support")
Reported-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1622552943-119174-1-git-send-email-kan.liang@linux.intel.com
|
|
This test case fails on s390 virtual machine z/VM which has no PMU support
when the perf tool is built with LIBPFM4=1.
Using make LIBPFM4=1 builds the perf tool with support for libpfm
event notation. The command line flag --pfm-events is valid:
# ./perf record --pfm-events cycles -- true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data (2 samples) ]
#
However the command 'perf test -Fv 17' fails on s390 z/VM virtual machine
with LIBPFM4=1:
# perf test -Fv 17
17: Setup struct perf_event_attr :
--- start ---
.....
running './tests/attr/test-record-group2'
unsupp './tests/attr/test-record-group2'
running './tests/attr/test-record-pfm-period'
expected exclude_hv=0, got 1
FAILED './tests/attr/test-record-pfm-period' - match failure
---- end ----
Setup struct perf_event_attr: FAILED!
When --pfm-event system is not supported, the test returns unsupported
and continues. Here is an example using a virtual machine on x86 and
Fedora 34:
[root@f33 perf]# perf test -Fv 17
17: Setup struct perf_event_attr :
--- start ---
.....
running './tests/attr/test-record-group2'
unsupp './tests/attr/test-record-group2'
running './tests/attr/test-record-pfm-period'
unsupp './tests/attr/test-record-pfm-period'
....
The issue is file ./tests/attr/test-record-pfm-period
which requires perf event attribute member exclude_hv to be zero.
This is not the case on s390 where the value of exclude_hv is one when
executing on a z/VM virtual machine without PMU hardware support.
Fix this by allowing value exlucde_hv to be zero or one.
Output before:
# /usr/bin/python ./tests/attr.py -d ./tests/attr/ -t \
test-record-pfm-period -p ./perf -vvv 2>&1| fgrep match
matching [event:base-record]
match: [event:base-record] matches []
FAILED './tests/attr//test-record-pfm-period' - match failure
#
Output after:
# /usr/bin/python ./tests/attr.py -d ./tests/attr/ -t \
test-record-pfm-period -p ./perf -vvv 2>&1| fgrep match
matching [event:base-record]
match: [event:base-record] matches ['event-1-0-6', 'event-1-0-5']
matched
Background:
Using libpfm library ends up in this function call sequence
pfm_get_perf_event_encoding()
+-- pfm_get_os_event_encoding()
+-- pfmlib_perf_event_encode()
is called when no hardware specific PMU unit can be detected
as in the s390 z/VM virtual machine case. This uses the
"perf_events generic PMU" data structure which sets exclude_hv
to 1 per default. Using this PMU that test case always fails.
That is the reason why exclude_hv attribute setting varies.
Version 2:
As suggested by Ian Rogers make perf_event_attribute member
exclude_hv more robust and accept value 0 or 1 to handle more
test cases which might fail on s390 virtual machine z/VM.
Suggested-by: Ian Rogers <irogers@google.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Ian Rogers <irogers@google.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Sumanth Korikkar <sumanthk@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Link: http://lore.kernel.org/lkml/20210528091050.245838-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Committer notes:
Added the missing {} for the now multiline 'if' block, fixing this error:
CC /tmp/build/perf/util/bpf_counter.o
util/bpf_counter.c: In function ‘bperf__load’:
util/bpf_counter.c:523:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
523 | if (evsel->bperf_leader_link_fd < 0 &&
| ^~
util/bpf_counter.c:526:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
526 | goto out;
| ^~~~
cc1: all warnings being treated as errors
Fixes: 7fac83aaf2eecc9e ("perf stat: Introduce 'bperf' to share hardware PMCs with BPF")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Cc: Zhang Yi <yi.zhang@huawei.com>
Link: http://lore.kernel.org/lkml/20210517081254.1561564-1-yukuai3@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
I found that checking cgroup sampling support using the missing features
doesn't work on old kernels. Because it added both attr.cgroup bit and
PERF_SAMPLE_CGROUP bit, it needs to check whichever comes first (usually
the actual event, not dummy).
But it only checks the attr.cgroup bit which is set only in the dummy
event so cannot detect failtures due the sample bits. Also we don't
ignore the missing feature and retry, it'd be better checking it with
the API probing logic.
Committer notes:
Extracted the minimal part to check using the new cgroup API probe
routine, the part that removes the cgroup member can be left for further
discussion.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210527182835.1634339-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
If we just check whether the variable can be converted, 'tvar' should be
a null pointer. However, the null pointer check is missing in the
'Constant value' execution path.
The following cases can trigger this problem:
$ cat test.c
#include <stdio.h>
void main(void)
{
int a;
const int b = 1;
asm volatile("mov %1, %0" : "=r"(a): "i"(b));
printf("a: %d\n", a);
}
$ gcc test.c -o test -O -g
$ sudo ./perf probe -x ./test -L "main"
<main@/home/lhf/test.c:0>
0 void main(void)
{
2 int a;
const int b = 1;
asm volatile("mov %1, %0" : "=r"(a): "i"(b));
6 printf("a: %d\n", a);
}
$ sudo ./perf probe -x ./test -V "main:6"
Segmentation fault
The check on 'tvar' is added. If 'tavr' is a null pointer, we return 0
to indicate that the variable can be converted. Now, we can successfully
show the variables that can be accessed.
$ sudo ./perf probe -x ./test -V "main:6"
Available variables at main:6
@<main+13>
char* __fmt
int a
int b
However, the variable 'b' cannot be tracked.
$ sudo ./perf probe -x ./test -D "main:6 b"
Failed to find the location of the 'b' variable at this address.
Perhaps it has been optimized out.
Use -V with the --range option to show 'b' location range.
Error: Failed to add events.
This is because __die_find_variable_cb() did not successfully match
variable 'b', which has the DW_AT_const_value attribute instead of
DW_AT_location. We added support for DW_AT_const_value in
__die_find_variable_cb(). With this modification, we can successfully
track the variable 'b'.
$ sudo ./perf probe -x ./test -D "main:6 b"
p:probe_test/main_L6 /home/lhf/test:0x1156 b=\1:s32
Fixes: 66f69b219716 ("perf probe: Support DW_AT_const_value constant value")
Signed-off-by: Li Huafei <lihuafei1@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Jianlin Lv <jianlin.lv@arm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Zhang Jinhao <zhangjinhao2@huawei.com>
http://lore.kernel.org/lkml/20210601092750.169601-1-lihuafei1@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
To allow the build to complete on older systems, where those files are
either not uptodate, lacking some recent additions or not present at
all.
And check if the copy drifts from the kernel.
This commit is similar with
commit 12f020338a2c ("tools: Copy uapi/asm/perf_regs.h from the kernel")
With this commit, we can avoid the following build error in any case:
tools/perf/arch/mips/include/perf_regs.h:7:10:
fatal error: asm/perf_regs.h: No such file or directory
#include <asm/perf_regs.h>
^~~~~~~~~~~~~~~~~
compilation terminated.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Xuefeng Li <lixuefeng@loongson.cn>
Link: http://lore.kernel.org/lkml/1622548436-12472-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Commit c7299fea6769 ("spi: Fix spi device unregister flow") changed the
SPI core's behavior if the ->setup() hook returns an error upon adding
an spi_device: Before, the ->cleanup() hook was invoked to free any
allocations that were made by ->setup(). With the commit, that's no
longer the case, so the ->setup() hook is expected to free the
allocations itself.
I've identified 5 drivers which depend on the old behavior and am fixing
them up hereinafter: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c spi-pxa2xx.c
Importantly, ->setup() is not only invoked on spi_device *addition*:
It may subsequently be called to *change* SPI parameters. If changing
these SPI parameters fails, freeing memory allocations would be wrong.
That should only be done if the spi_device is finally destroyed.
I am therefore using a bool "initial_setup" in 4 of the affected drivers
to differentiate between the invocation on *adding* the spi_device and
any subsequent invocations: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c
In spi-pxa2xx.c, it seems the ->setup() hook can only fail on spi_device
addition, not any subsequent calls. It therefore doesn't need the bool.
It's worth noting that 5 other drivers already perform a cleanup if the
->setup() hook fails. Before c7299fea6769, they caused a double-free
if ->setup() failed on spi_device addition. Since the commit, they're
fine. These drivers are: spi-mpc512x-psc.c spi-pl022.c spi-s3c64xx.c
spi-st-ssc4.c spi-tegra114.c
(spi-pxa2xx.c also already performs a cleanup, but only in one of
several error paths.)
Fixes: c7299fea6769 ("spi: Fix spi device unregister flow")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Saravana Kannan <saravanak@google.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # pxa2xx
Link: https://lore.kernel.org/r/f76a0599469f265b69c371538794101fa37b5536.1622149321.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The .n_voltages was missed for pickable linear ranges, fix it.
The min_sel for each pickable range should be starting from 0.
Also fix atc260x_ldo_voltage_range_sel setting (bit 5 - LDO<N>_VOL_SEL
in datasheet).
Fixes: 3b15ccac161a ("regulator: Add regulator driver for ATC260x PMICs")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Link: https://lore.kernel.org/r/20210528230147.363974-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
- Fix to make regcache value first reading back from HW.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1622542155-6373-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The .of_map_mode should has below function prototype:
unsigned int (*of_map_mode)(unsigned int mode);
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210530022109.425054-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The other Richtek drivers has Richtek prefix, make it consistent.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210530124101.477727-2-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current code does not set .curr_table and .n_linear_ranges settings,
so it cannot use the regulator_get/set_current_limit_regmap helpers.
If we setup the curr_table, it will has 200 entries.
Implement customized .set_current_limit/.get_current_limit callbacks
instead.
Fixes: b8c054a5eaf0 ("regulator: rtmv20: Adds support for Richtek RTMV20 load switch regulator")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20210530124101.477727-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The recent changes to use common code to power up/down DSP cores also
removed the reset of the core state at suspend. It turns out this is
still needed. When the firmware state is reset to
SOF_FW_BOOT_NOT_STARTED, also enabled_cores should be reset, and
existing DSP drivers depend on this.
BugLink: https://github.com/thesofproject/linux/issues/2824
Fixes: 42077f08b3 ("ASoC: SOF: update dsp core power status in common APIs")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20210528144330.2551-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Otherwise, when compiled as module, a WARN_ON is triggered:
WARNING: CPU: 0 PID: 5 at sound/core/init.c:208 snd_card_new+0x310/0x39c [snd]
[...]
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.10.39 #1
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: events deferred_probe_work_func
[<c0111988>] (unwind_backtrace) from [<c010c8ac>] (show_stack+0x10/0x14)
[<c010c8ac>] (show_stack) from [<c092784c>] (dump_stack+0xdc/0x104)
[<c092784c>] (dump_stack) from [<c0129710>] (__warn+0xd8/0x114)
[<c0129710>] (__warn) from [<c0922a48>] (warn_slowpath_fmt+0x5c/0xc4)
[<c0922a48>] (warn_slowpath_fmt) from [<bf0496f8>] (snd_card_new+0x310/0x39c [snd])
[<bf0496f8>] (snd_card_new [snd]) from [<bf1d7df8>] (snd_soc_bind_card+0x334/0x9c4 [snd_soc_core])
[<bf1d7df8>] (snd_soc_bind_card [snd_soc_core]) from [<bf1e9cd8>] (devm_snd_soc_register_card+0x30/0x6c [snd_soc_core])
[<bf1e9cd8>] (devm_snd_soc_register_card [snd_soc_core]) from [<bf22d964>] (fsl_asoc_card_probe+0x550/0xcc8 [snd_soc_fsl_asoc_card])
[<bf22d964>] (fsl_asoc_card_probe [snd_soc_fsl_asoc_card]) from [<c060c930>] (platform_drv_probe+0x48/0x98)
[...]
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20210527163409.22049-1-nicolas.cavallari@green-communications.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are spelling mistakes in comments. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210601103506.9477-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For the HP Pavilion 15-CK0xx, with audio subsystem ID 0x103c:0x841c,
adding a line in patch_realtek.c to apply the ALC269_FIXUP_HP_MUTE_LED_MIC3
fix activates the mute key LED.
Signed-off-by: Carlos M <carlos.marr.pz@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210531202026.35427-1-carlos.marr.pz@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In commit 68dc022d04eb ("xfrm: BEET mode doesn't support fragments
for inner packets"), it tried to fix the issue that in TX side the
packet is fragmented before the ESP encapping while in the RX side
the fragments always get reassembled before decapping with ESP.
This is not true for IPv6. IPv6 is different, and it's using exthdr
to save fragment info, as well as the ESP info. Exthdrs are added
in TX and processed in RX both in order. So in the above case, the
ESP decapping will be done earlier than the fragment reassembling
in TX side.
Here just remove the fragment check for the IPv6 inner packets to
recover the fragments support for BEET mode.
Fixes: 68dc022d04eb ("xfrm: BEET mode doesn't support fragments for inner packets")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Previously this fix was applied only to Bullseye variant laptops,
and should be applied to Cyborg and Warlock variants.
Fixes: 45b14fe200ba ("ALSA: hda/cirrus: Use CS8409 filter to fix abnormal sounds on Bullseye")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210531163754.136736-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Function 'xfrm_parse_spi' is declared twice, so remove the
repeated declaration.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
xfrm_policy_lookup_bytype
xfrm_policy_lookup_bytype loops on seqcount mutex xfrm_policy_hash_generation
within an RCU read side critical section. Although ill advised, this is fine if
the loop is bounded.
xfrm_policy_hash_generation wraps mutex hash_resize_mutex, which is used to
serialize writers (xfrm_hash_resize, xfrm_hash_rebuild). This is fine too.
On PREEMPT_RT=y, the read_seqcount_begin call within xfrm_policy_lookup_bytype
emits a mutex lock/unlock for hash_resize_mutex. Mutex locking is fine, since
RCU read side critical sections are allowed to sleep with PREEMPT_RT.
xfrm_hash_resize can, however, block on synchronize_rcu while holding
hash_resize_mutex.
This leads to the following situation on PREEMPT_RT, where the writer is
blocked on RCU grace period expiry, while the reader is blocked on a lock held
by the writer:
Thead 1 (xfrm_hash_resize) Thread 2 (xfrm_policy_lookup_bytype)
rcu_read_lock();
mutex_lock(&hash_resize_mutex);
read_seqcount_begin(&xfrm_policy_hash_generation);
mutex_lock(&hash_resize_mutex); // block
xfrm_bydst_resize();
synchronize_rcu(); // block
<RCU stalls in xfrm_policy_lookup_bytype>
Move the read_seqcount_begin call outside of the RCU read side critical section,
and do an rcu_read_unlock/retry if we got stale data within the critical section.
On non-PREEMPT_RT, this shortens the time spent within RCU read side critical
section in case the seqcount needs a retry, and avoids unbounded looping.
Fixes: 77cc278f7b20 ("xfrm: policy: Use sequence counters with associated lock")
Signed-off-by: Varad Gautam <varad.gautam@suse.com>
Cc: linux-rt-users <linux-rt-users@vger.kernel.org>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # v4.9
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Florian Westphal <fw@strlen.de>
Cc: "Ahmed S. Darwish" <a.darwish@linutronix.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Ahmed S. Darwish <a.darwish@linutronix.de>
|
|
It's possible to trigger NULL pointer dereference by local unprivileged
user, when calling getsockname() after failed bind() (e.g. the bind
fails because LLCP_SAP_MAX used as SAP):
BUG: kernel NULL pointer dereference, address: 0000000000000000
CPU: 1 PID: 426 Comm: llcp_sock_getna Not tainted 5.13.0-rc2-next-20210521+ #9
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1 04/01/2014
Call Trace:
llcp_sock_getname+0xb1/0xe0
__sys_getpeername+0x95/0xc0
? lockdep_hardirqs_on_prepare+0xd5/0x180
? syscall_enter_from_user_mode+0x1c/0x40
__x64_sys_getpeername+0x11/0x20
do_syscall_64+0x36/0x70
entry_SYSCALL_64_after_hwframe+0x44/0xae
This can be reproduced with Syzkaller C repro (bind followed by
getpeername):
https://syzkaller.appspot.com/x/repro.c?x=14def446e00000
Cc: <stable@vger.kernel.org>
Fixes: d646960f7986 ("NFC: Initial LLCP support")
Reported-by: syzbot+80fb126e7f7d8b1a5914@syzkaller.appspotmail.com
Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210531072138.5219-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The abort_cmd_ia flag in an abort wqe describes whether an ABTS basic link
service should be transmitted on the FC link or not. Code added in
lpfc_sli4_issue_abort_iotag() set the abort_cmd_ia flag incorrectly,
surpressing ABTS transmission.
A previous LPFC change to build an abort wqe inverted prior logic that
determined whether an ABTS was to be issued on the FC link.
Revert this logic to its proper state.
Link: https://lore.kernel.org/r/20210528212240.11387-1-jsmart2021@gmail.com
Fixes: db7531d2b377 ("scsi: lpfc: Convert abort handling to SLI-3 and SLI-4 handlers")
Cc: <stable@vger.kernel.org> # v5.11+
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On realtime kernels, spin_lock_irq*(spinlock_t) do not disable the
interrupts, a call to irqs_disabled() will return false thus firing a
warning in __transport_wait_for_tasks().
Remove the warning and also replace assert_spin_locked() with
lockdep_assert_held()
Link: https://lore.kernel.org/r/20210531121326.3649-1-mlombard@redhat.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This reverts commit 3c0468d4451eb6b4f6604370639f163f9637a479.
That commit was breaking alignment guarantees for the DMA address when
allocating coherent mappings, as described in
Documentation/core-api/dma-api-howto.rst
It was also noticed by Mellanox' driver:
[ 1515.763621] mlx5_core c002:01:00.0: mlx5_frag_buf_alloc_node:146:(pid 13402): unexpected map alignment: 0x0800000000c61000, page_shift=16
[ 1515.763635] mlx5_core c002:01:00.0: mlx5_cqwq_create:181:(pid
13402): mlx5_frag_buf_alloc_node() failed, -12
Fixes: 3c0468d4451e ("powerpc/kernel/iommu: Align size for IOMMU_PAGE_SIZE() to save TCEs")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210526144540.117795-1-fbarrat@linux.ibm.com
|
|
There are machines out there with added value crap^WBIOS which provide an
SMI handler for the local APIC thermal sensor interrupt. Out of reset,
the BSP on those machines has something like 0x200 in that APIC register
(timestamps left in because this whole issue is timing sensitive):
[ 0.033858] read lvtthmr: 0x330, val: 0x200
which means:
- bit 16 - the interrupt mask bit is clear and thus that interrupt is enabled
- bits [10:8] have 010b which means SMI delivery mode.
Now, later during boot, when the kernel programs the local APIC, it
soft-disables it temporarily through the spurious vector register:
setup_local_APIC:
...
/*
* If this comes from kexec/kcrash the APIC might be enabled in
* SPIV. Soft disable it before doing further initialization.
*/
value = apic_read(APIC_SPIV);
value &= ~APIC_SPIV_APIC_ENABLED;
apic_write(APIC_SPIV, value);
which means (from the SDM):
"10.4.7.2 Local APIC State After It Has Been Software Disabled
...
* The mask bits for all the LVT entries are set. Attempts to reset these
bits will be ignored."
And this happens too:
[ 0.124111] APIC: Switch to symmetric I/O mode setup
[ 0.124117] lvtthmr 0x200 before write 0xf to APIC 0xf0
[ 0.124118] lvtthmr 0x10200 after write 0xf to APIC 0xf0
This results in CPU 0 soft lockups depending on the placement in time
when the APIC soft-disable happens. Those soft lockups are not 100%
reproducible and the reason for that can only be speculated as no one
tells you what SMM does. Likely, it confuses the SMM code that the APIC
is disabled and the thermal interrupt doesn't doesn't fire at all,
leading to CPU 0 stuck in SMM forever...
Now, before
4f432e8bb15b ("x86/mce: Get rid of mcheck_intel_therm_init()")
due to how the APIC_LVTTHMR was read before APIC initialization in
mcheck_intel_therm_init(), it would read the value with the mask bit 16
clear and then intel_init_thermal() would replicate it onto the APs and
all would be peachy - the thermal interrupt would remain enabled.
But that commit moved that reading to a later moment in
intel_init_thermal(), resulting in reading APIC_LVTTHMR on the BSP too
late and with its interrupt mask bit set.
Thus, revert back to the old behavior of reading the thermal LVT
register before the APIC gets initialized.
Fixes: 4f432e8bb15b ("x86/mce: Get rid of mcheck_intel_therm_init()")
Reported-by: James Feeney <james@nurealm.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lkml.kernel.org/r/YKIqDdFNaXYd39wz@zn.tnic
|
|
The commit cb17ed29a7a5 ("mac80211: parse radiotap header when selecting Tx
queue") moved the code to validate the radiotap header from
ieee80211_monitor_start_xmit to ieee80211_parse_tx_radiotap. This made is
possible to share more code with the new Tx queue selection code for
injected frames. But at the same time, it now required the call of
ieee80211_parse_tx_radiotap at the beginning of functions which wanted to
handle the radiotap header. And this broke the rate parser for radiotap
header parser.
The radiotap parser for rates is operating most of the time only on the
data in the actual radiotap header. But for the 802.11a/b/g rates, it must
also know the selected band from the chandef information. But this
information is only written to the ieee80211_tx_info at the end of the
ieee80211_monitor_start_xmit - long after ieee80211_parse_tx_radiotap was
already called. The info->band information was therefore always 0
(NL80211_BAND_2GHZ) when the parser code tried to access it.
For a 5GHz only device, injecting a frame with 802.11a rates would cause a
NULL pointer dereference because local->hw.wiphy->bands[NL80211_BAND_2GHZ]
would most likely have been NULL when the radiotap parser searched for the
correct rate index of the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: cb17ed29a7a5 ("mac80211: parse radiotap header when selecting Tx queue")
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
[sven@narfation.org: added commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20210530133226.40587-1-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Replace hard-coded compile-time constants for header length check
with dynamic determination based on the frame type. Otherwise, we
hit a validation WARN_ON in cfg80211 later.
Fixes: cd418ba63f0c ("mac80211: convert S1G beacon to scan results")
Reported-by: syzbot+405843667e93b9790fc1@syzkaller.appspotmail.com
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Link: https://lore.kernel.org/r/20210510041649.589754-1-ducheng2@gmail.com
[style fixes, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Due to the locking changes and callbacks happening inside
cfg80211, we need to use cfg80211 versions of the register
and unregister functions if called within cfg80211 methods,
otherwise deadlocks occur.
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210426212801.3d902cc9e6f4.Ie0b1e0c545920c61400a4b7d0f384ea61feb645a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the userland switches back-and-forth between NL80211_IFTYPE_OCB and
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), there is a
chance where the cleanup cfg80211_leave_ocb() is not called. This leads
to initialization of in-use memory (e.g. init u.ibss while in-use by
u.ocb) due to a shared struct/union within ieee80211_sub_if_data:
struct ieee80211_sub_if_data {
...
union {
struct ieee80211_if_ap ap;
struct ieee80211_if_vlan vlan;
struct ieee80211_if_managed mgd;
struct ieee80211_if_ibss ibss; // <- shares address
struct ieee80211_if_mesh mesh;
struct ieee80211_if_ocb ocb; // <- shares address
struct ieee80211_if_mntr mntr;
struct ieee80211_if_nan nan;
} u;
...
}
Therefore add handling of otype == NL80211_IFTYPE_OCB, during
cfg80211_change_iface() to perform cleanup when leaving OCB mode.
link to syzkaller bug:
https://syzkaller.appspot.com/bug?id=0612dbfa595bf4b9b680ff7b4948257b8e3732d5
Reported-by: syzbot+105896fac213f26056f9@syzkaller.appspotmail.com
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Link: https://lore.kernel.org/r/20210428063941.105161-1-ducheng2@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit a05829a7222e ("cfg80211: avoid holding the RTNL when calling the
driver") dropped usage of RTNL here and replaced it with
hw->wiphy->mutex. But we didn't update the comments.
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20210505202829.1039400-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Syzbot reports that we may be able to get into a situation where
mac80211 has pending ACK frames on shutdown with hwsim. It appears
that the reason for this is that syzbot uses the wmediumd hooks to
intercept/injection frames, and may shut down hwsim, removing the
radio(s), while frames are pending in the air simulation.
Clean out the pending queue when the interface is stopped, after
this the frames can't be reported back to mac80211 properly anyway.
Reported-by: syzbot+a063bbf0b15737362592@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210517170429.b0f85ab0eda1.Ie42a6ec6b940c971f3441286aeaaae2fe368e29a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Syzbot reports that it's possible to hit this from userspace,
by trying to add a station before any other connection setup
has been done. Instead of trying to catch this in some other
way simply remove the warning, that will appropriately reject
the call from userspace.
Reported-by: syzbot+7716dbc401d9a437890d@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210517164715.f537da276d17.Id05f40ec8761d6a8cc2df87f1aa09c651988a586@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The recent commit to drop the HDA-specific mute-LED control,
e65bf99718b5 ("ALSA: HDA - remove the custom implementation for the
audio LED trigger"), caused a regression on the mixer element read for
"Capture Switch" when it's built from bind controls. The function
create_bind_cap_vol_ctl() creates the snd_kcontrol_new object directly
via snd_hda_gen_add_kctl() instead of add_control(). Although the
commit above added a workaround for the SNDRV_CTL_ACCESS_READWRITE in
add_control() as default, this code path fell out from the radar. As
a result, now the driver gives -EPERM error because of the lack of the
proper access bit at reading "Capture Switch" element value.
Fix the regression by setting the access bit properly.
Fixes: e65bf99718b5 ("ALSA: HDA - remove the custom implementation for the audio LED trigger")
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1186634
Link: https://lore.kernel.org/r/20210531180633.27831-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fixes from Andreas Gruenbacher:
"Various gfs2 fixes"
* tag 'gfs2-v5.13-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix use-after-free in gfs2_glock_shrink_scan
gfs2: Fix mmap locking for write faults
gfs2: Clean up revokes on normal withdraws
gfs2: fix a deadlock on withdraw-during-mount
gfs2: fix scheduling while atomic bug in glocks
gfs2: Fix I_NEW check in gfs2_dinode_in
gfs2: Prevent direct-I/O write fallback errors from getting lost
|
