| Age | Commit message (Collapse) | Author |
|---|
|
Starting with commit 80c33dd "net: add might_sleep() call to napi_disable"
bnx2x fails the might_sleep tests causing a stack trace to appear whenever
the driver is unloaded, as local_bh_disable() is being called before
napi_disable().
This changes the locking schematics related to CONFIG_NET_RX_BUSY_POLL,
preventing the need for calling local_bh_disable() and thus eliminating
the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* pm-cpuidle:
intel_idle: close avn_cstates array with correct marker
Revert "intel_idle: mark states tables with __initdata tag"
|
|
Close avn_cstates array with correct marker to avoid overflow
in function intel_idle_cpu_init().
[rjw: The problem was introduced when commit 22e580d07f65 was merged
on top of eba682a5aeb6 (intel_idle: shrink states tables).]
Fixes: 22e580d07f65 (intel_idle: Fixed C6 state on Avoton/Rangeley processors)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Function tracing callbacks expect to have the ftrace_ops that registered it
passed to them, not the address of the variable that holds the ftrace_ops
that registered it.
Use a mov instead of a lea to store the ftrace_ops into the parameter
of the function tracing callback.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/20131113152004.459787f9@gandalf.local.home
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.8+
|
|
Add support for adreno 330. Not too much different, just a few
differences in initial configuration plus setting OCMEM base.
Userspace support is already in upstream mesa.
Note that the existing DT code is simply using the bindings from
downstream android kernel, to simplify porting of this driver to
existing devices. These do not constitute any committed/stable
DT ABI. The addition of proper DT bindings will be a subsequent
patch, at which point (as best as possible) I will try to support
either upstream bindings or what is found in downstream android
kernel, so that existing device DT files can be used.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Add support for the new MDP5 display controller block. The mapping
between parts of the display controller and KMS is:
plane -> PIPE{RGBn,VIGn} \
crtc -> LM (layer mixer) |-> MDP "device"
encoder -> INTF /
connector -> HDMI/DSI/eDP/etc --> other device(s)
Unlike MDP4, it appears we can get by with a single encoder, rather
than needing a different implementation for DTV, DSI, etc. (Ie. the
register interface is same, just different bases.)
Also unlike MDP4, all the IRQs for other blocks (HDMI, DSI, etc) are
routed through MDP.
And finally, MDP5 has this "Shared Memory Pool" (called "SMP"), from
which blocks need to be allocated to the active pipes based on fetch
stride.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The HDMI block is basically the same between older SoC's with mdp4
display controller, and newer ones with mdp5.
So mostly this consists of better abstracting out the different sets of
regulators, clks, etc. In particular, for regulators and clks we can
split it up by what is needed for hot plug detect to work, and what is
needed to light up the display.
Also, 8x74 has a new phy.. a very simple one, but split out into a
different mmio space. And with mdp5, the irq is shared with mdp, so we
don't directly register our own irq handler.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
We'll want basically the same thing for mdp5, so refactor it out so it
can be shared.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This can be shared between mdp4 and mdp5. Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
resync to latest envytools db, add mdp5 registers
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This adds the necessary configuration for the APQ8060A SoC (dual-core
krait + a320 gpu) as found on the bstem board.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Add a VRAM carveout that is used for systems which do not have an IOMMU.
The VRAM carveout uses CMA. The arch code must setup a CMA pool for the
device (preferrably in highmem.. a 256m-512m VRAM pool in lowmem is not
cool). The user can configure the VRAM pool size using msm.vram module
param.
Technically, the abstraction of IOMMU behind msm_mmu is not strictly
needed, but it simplifies the GEM code a bit, and will be useful later
when I add support for a2xx devices with GPUMMU, so I decided to keep
this part.
It appears to be possible to configure the GPU to restrict access to
addresses within the VRAM pool, but this is not done yet. So for now
the GPU will refuse to load if there is no sort of mmu. Once address
based limits are supported and tested to confirm that we aren't giving
the GPU access to arbitrary memory, this restriction can be lifted
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This got a bit broken with original patches when re-arranging things to
move dependencies on mach-msm inside #ifndef OF.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
With a simple stub, we can get COMPILE_TEST support.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Enable use of DT for DMM/Tiler.
Originally worked on by Andy Gross <andygro@gmail.com>
Cc: Andy Gross <andygro@gmail.com>
Cc: DRI Development <dri-devel@lists.freedesktop.org>
Signed-off-by: Archit Taneja <archit@ti.com>
[tomi.valkeinen@ti.com: use of_match_ptr()]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The current dev_unload order uninits the irqs too early.
In the current sequence, it's possible that a crtc queues work(apply_worker)
to display a buffer, which registers to omap_crtc_apply_irq to notfiy the
completion of the configuration we applied.
Calling drm_vblank_cleanup and omap_drm_irq_uninstall here causes the crtc's
apply handler to never get called, which results in an incorrect state of the
apply_irq.registered parameter.
This condition occurs where there is no mode set via omapdrm, and dev_lastclose
tries to set a default fb mode via drm_fb_helper_restore_fbdev_mode. The apply
work scheduled by restore_fbdev_mode is very close in time to the disabling of
the irq handler, and hence leads to a race condition. We move the irq cleanup
at the end of the unload sequence to prevent this.
Also, the call to flush_workqueue is removed since it's called internally by
destroy_workqueue.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Currently, an encoder is disabled only when an apply work is queued for the
corresponding crtc. This works fine for the paths where userspace explicitly
disables crtc, this results in disabling the omapdss device in the crtc's
pre_apply function.
However, when the omapdrm module is removed, there is no work queued to ensure
that the encoder is disabled. This can result in an enabled omapdss device when
removing omapdrm. omapdss is left in an inconsistent state, and that prevents us
from using that omapdss device being used again.
Disable enabled encoders in omap_encoder_destroy, we could consider a better
place for doing this later.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
At omapdrm probe, we install manager ops and connect omapdss devices. This
needs to be undone when omapdrm module is removed so that omapdss is in a
clean state. This ensures that we can re-insert omapdrm module, or some other
module which uses omapdss(like omapfb/omap_vout).
Currently, omapdrm's remove neither uninstalls manager ops, or disconnects
omapdss devices. We make sure that this is done in pdev_remove.
omapdrm establishes connections for omap_dss_device devices when probed. It
should also be responsible to disconnect the devices. Keeping the devices
connected can prevent the panel driver modules from unloading, it also causes
issues when we try to remove or re-insert omapdrm module.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
With the omapdss device model changes. omapdrm is required to call dssdriver's
connect() op to register a panel. This is currently done in omap_modeset_init()
A call to connect() can fail if the omapdss panels or the encoders(HDMI/DPI)
they connect to have some resource(like regulators, I2C adapter) missing. If
this happens, the correct approach is to defer omapdrm's probe.
omapdrm currently ignores those panels which return a non zero value when
connected. This could result in omapdrm ignoring all panels on an omap board.
The right approach would be for omapdrm to request for probe deferral when a
panel's connect op returns -EPROBE_DEFER.
In order to do this, we need to call connect() much earlier during omapdrm's
probe to prevent too many things are already done by then. We now connect the
panels during pdev_probe(), before anything else is initialized, so that we
don't need to undo too many things if a defer was requested.
Now when we enter omap_modeset_init(), we have a set of panels that have been
connected. We now proceed with registering only those panels that are already
connected.
A special case has to be considered when no panels are available to connect when
omapdrm probes. In this case too, we defer probe and expect that a panel will be
available to connect the next time.
Checking whether the panel has a driver or whether it has get_timing/read_edid
ops in omap_modeset_init() are redundant with the new display model. These can
be removed since a dssdev device will always have a driver associated with it,
and all dssdev drivers have a get_timings op.
This will mainly fix cases when omapdrm is built-in the kernel, since that's
generally where resources like regulators or I2C are unavailable because of
probe order dependencies.
In particular this fixes boot with omapdrm built-in on an omap4 panda ES board.
The regulators used by HDMI(provided by I2C based TWL regulators) aren't
initialized because I2C isn't initialized, I2C isn't initialized as it's pins
are not configured because pinctrl is yet to probe.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
omapdrm (un)registers irqs inside an irq handler. The problem is that
the (un)register function uses dispc_runtime_get/put() to enable the
clocks, and those functions are not irq safe by default.
This was kind of fixed in 48664b21aeeffb40c5fa06843f18052e2c4ec9ef
(OMAPDSS: DISPC: set irq_safe for runtime PM), which makes dispc's
runtime calls irq-safe.
However, using pm_runtime_irq_safe in dispc makes the parent of dispc,
dss, always enabled, effectively preventing PM for the whole DSS module.
This patch makes omapdrm behave better by adding new irq (un)register
functions that do not use dispc_runtime_get/put, and using those
functions in interrupt context. Thus we can make dispc again
non-irq-safe, allowing proper PM.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Rob Clark <robdclark@gmail.com>
|
|
This reverts commit 9d046ccb98085f1d437585f84748c783a04ba240.
Commit 9d046ccb98085 marks all state tables with __initdata, but
the state table may be accessed when doing CPU online, which then
causing system crash as below:
[ 204.188841] BUG: unable to handle kernel paging request at ffffffff8227cce8
[ 204.196844] IP: [<ffffffff814aa1c0>] intel_idle_cpu_init+0x40/0x130
[ 204.203996] PGD 1e11067 PUD 1e12063 PMD 455859063 PTE 800000000227c062
[ 204.211638] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[ 204.216975] Modules linked in: x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd gpio_ich microcode joydev sb_edac edac_core ipmi_si lpc_ich ipmi_msghandler lp tpm_tis parport wmi mac_hid acpi_pad hid_generic ixgbe isci usbhid dca hid libsas ptp ahci libahci scsi_transport_sas megaraid_sas pps_core mdio
[ 204.262815] CPU: 11 PID: 1489 Comm: bash Not tainted 3.13.0-rc7+ #48
[ 204.269993] Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRIVTIN1.86B.0047.L09.1312061514 12/06/2013
[ 204.281646] task: ffff8804303a24a0 ti: ffff880440fac000 task.ti: ffff880440fac000
[ 204.290311] RIP: 0010:[<ffffffff814aa1c0>] [<ffffffff814aa1c0>] intel_idle_cpu_init+0x40/0x130
[ 204.300184] RSP: 0018:ffff880440fadd28 EFLAGS: 00010286
[ 204.306192] RAX: ffffffff8227cca0 RBX: ffffe8fff1a03400 RCX: 0000000000000007
[ 204.314244] RDX: ffff88045f400000 RSI: 0000000000000009 RDI: 0000000000001120
[ 204.322296] RBP: ffff880440fadd38 R08: 0000000000000000 R09: 0000000000000001
[ 204.330411] R10: 0000000000000001 R11: 0000000000000000 R12: 000000000000001e
[ 204.338482] R13: 00000000ffffffdb R14: 0000000000000001 R15: 0000000000000000
[ 204.346743] FS: 00007f64f7b0c740(0000) GS:ffff88045ce00000(0000) knlGS:0000000000000000
[ 204.355919] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 204.362449] CR2: ffffffff8227cce8 CR3: 0000000444ab0000 CR4: 00000000001407e0
[ 204.370520] Stack:
[ 204.372853] 000000000000001e ffffffff81f10240 ffff880440fadd50 ffffffff814aa307
[ 204.381519] ffffffff81ea80e0 ffff880440fadda0 ffffffff8185a230 0000000000000000
[ 204.390196] 000000000000001e 0000000000000002 0000000000000002 0000000000000000
[ 204.398856] Call Trace:
[ 204.401683] [<ffffffff814aa307>] cpu_hotplug_notify+0x57/0x70
[ 204.408638] [<ffffffff8185a230>] notifier_call_chain+0x100/0x150
[ 204.415553] [<ffffffff810a7dae>] __raw_notifier_call_chain+0xe/0x10
[ 204.422772] [<ffffffff81072163>] cpu_notify+0x23/0x50
[ 204.428616] [<ffffffff810723b2>] _cpu_up+0x132/0x1a0
[ 204.434361] [<ffffffff8107249d>] cpu_up+0x7d/0xa0
[ 204.439819] [<ffffffff81836c9c>] cpu_subsys_online+0x3c/0x90
[ 204.446345] [<ffffffff81554625>] device_online+0x45/0xa0
[ 204.452471] [<ffffffff815546ce>] online_store+0x4e/0x80
[ 204.458511] [<ffffffff815519a8>] dev_attr_store+0x18/0x30
[ 204.464744] [<ffffffff812a68f1>] sysfs_write_file+0x151/0x1c0
[ 204.471681] [<ffffffff81217ef1>] vfs_write+0xe1/0x160
[ 204.477524] [<ffffffff8121889c>] SyS_write+0x4c/0x90
[ 204.483270] [<ffffffff8185f2ed>] system_call_fastpath+0x1a/0x1f
[ 204.490081] Code: 41 54 41 89 fc 8b 3d 48 25 85 01 53 48 8b 1d 30 25 85 01 48 03 1c c5 40 90 fb 81 48 8b 05 19 25 85 01 c7 43 0c 01 00 00 00 66 90 <48> 83 78 48 00 74 4f 41 83 c0 01 41 39 f0 7e 10 48 c7 c7 38 79
[ 204.515723] RIP [<ffffffff814aa1c0>] intel_idle_cpu_init+0x40/0x130
[ 204.522996] RSP <ffff880440fadd28>
[ 204.526976] CR2: ffffffff8227cce8
[ 204.530766] ---[ end trace 336f56cc3d1cfc8c ]---
Fixes: 9d046ccb98085 (intel_idle: mark states tables with __initdata tag)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"This patch fixes the kmap/kunmap implementation on parisc and finally
makes AIO work on parisc"
* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Ensure full cache coherency for kmap/kunmap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Late fixes for libata. Nothing too interesting. Adding missing PM
callbacks to satat_sis and an additional PCI ID for ahci"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_sis: missing PM support
ahci: add PCI ID for Marvell 88SE9170 SATA controller
|
|
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: fix rebase
v3: hide behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: hide behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: put behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
There's not much information still available on
r6xx, so r6xx is based on guess-work.
v2: put behind module parameter
v3: add IGP check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This is used to hard reset the asic. If a soft
reset is not able to reset things, a hard reset
can be used.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enabling this parameter enables pci config reset,
aka hard reset, which is a bus level chip reset.
In some cases this works more reliably than a soft
reset. Disabled by default.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Helge Deller noted a few weeks ago problems with the AIO support on
parisc. This change is the result of numerous iterations on how best to
deal with this problem.
The solution adopted here is to provide full cache coherency in a
uniform manner on all parisc systems. This involves calling
flush_dcache_page() on kmap operations and flush_kernel_dcache_page() on
kunmap operations. As a result, the copy_user_page() and
clear_user_page() functions can be removed and the overall code is
simpler.
The change ensures that both userspace and kernel aliases to a mapped
page are invalidated and flushed. This is necessary for the correct
operation of PA8800 and PA8900 based systems which do not support
inequivalent aliases.
With this change, I have observed no cache related issues on c8000 and
rp3440. It is now possible for example to do kernel builds with "-j64"
on four way systems.
On systems using XFS file systems, the patch recently posted by Mikulas
Patocka to "fix crash using XFS on loopback" is needed to avoid a hang
caused by an uninitialized lock passed to flush_dcache_page() in the
page struct.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the first NFC fixes pull request for 3.13.
It only contains one fix for a regression introduced with commit
e29a9e2ae165620d. Without this fix, we can not establish a p2p link in
target mode. Only initiator mode works."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
LPT does have PCH refclk, but it's different form the IBX/CPT/PPT one
and doesn't use the same structs. It is wrong to have a message saying
that "LPT does not has PCH refclk" (sic). While at it, signal that we
only want this function on IBX/CPT/PPT by renaming it and adding a
WARN.
On HSW we also print "0 shared PLLs initialized", but we *do* have
shared PLLs on HSW (LCPLL, WRPLL, SPLL) and we *do* initialize them.
We just don't use "struct intel_shared_dpll". So remove the debug
message.
In the future we may want to rename all that "intel shared pll" code
to "ibx shared pll", but I'll leave this to another patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This fixes a bug which was causing rejections of valid GPU commands
from userspace.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's never allocated on systems without an ATOMBIOS or COMBIOS ROM.
Should fix an oops I encountered while resetting the GPU after a lockup
on my PowerBook with an RV350.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Commit 6d9252bd9a4bb (clk: Add support for power of two type dividers)
merged in v3.6 added the _get_val function to convert a divisor value to
a register field value depending on the flags. However it used the type
u8 for the div field, causing divisors larger than 255 to be masked
and the resultant clock rate to be too high.
E.g. in my case an 11bit divider was supposed to divide 24.576 MHz down
to 32.768KHz. The divisor was correctly calculated as 750 (0x2ee). This
was masked to 238 (0xee) resulting in a frequency of 103.26KHz.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The Chunghwa CLAA101WA01A is a 10.1" 1366x768 panel, which can be
supported by the simple panel driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Samsung LNT101NT05 10.1" WXVGA panel can be supported by the simple panel
driver.
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Properly zero the refcounts and crtc->ddi_pll_set so the previous HW
state doesn't affect the result of reading the current HW state.
This fixes WARNs about WRPLL refcount if we have an HDMI monitor on
HSW and then suspend/resume.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64379
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
According to Art, we don't have a way to read back the state reliably at
runtime, through the control reg or the mailbox, at least not without risking
disabling it again. So drop the readout and checking on BDW.
v2: drop TODO comment (Paulo)
move POSTING_READ of control reg under HSW branch in disable (Paulo)
always report IPS as enabled on BDW (Paulo)
References: https://bugs.freedesktop.org/show_bug.cgi?id=71906
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Mark functions as static because they are not used outside the file
drm/vmwgfx/vmwgfx_fence.c.
This eliminates the following warnings in drm/vmwgfx/vmwgfx_fence.c:
drivers/gpu/drm/vmwgfx/vmwgfx_fence.c:274:6: warning: no previous prototype for ‘vmw_fences_perform_actions’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_fence.c:900:6: warning: no previous prototype for ‘vmw_fence_obj_add_action’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_fence.c:996:5: warning: no previous prototype for ‘vmw_event_fence_action_create’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
|
|
Mark functions as static because they are not used outside the file
drm/vmwgfx/vmwgfx_buffer.c.
This eliminates the following warnings in drm/vmwgfx/vmwgfx_buffer.c:
drivers/gpu/drm/vmwgfx/vmwgfx_buffer.c:520:16: warning: no previous prototype for ‘vmw_ttm_tt_create’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_buffer.c:549:5: warning: no previous prototype for ‘vmw_invalidate_caches’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_buffer.c:554:5: warning: no previous prototype for ‘vmw_init_mem_type’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_buffer.c:592:6: warning: no previous prototype for ‘vmw_evict_flags’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
|
|
Mark functions as static because they are not used outside the file
drm/vmwgfx/vmwgfx_kms.c.
This eliminates the following warnings in drm/vmwgfx/vmwgfx_kms.c:
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:43:6: warning: no previous prototype for ‘vmw_clip_cliprects’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:426:6: warning: no previous prototype for ‘vmw_framebuffer_surface_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:592:5: warning: no previous prototype for ‘vmw_framebuffer_surface_dirty’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:757:6: warning: no previous prototype for ‘vmw_framebuffer_dmabuf_destroy’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:943:5: warning: no previous prototype for ‘vmw_framebuffer_dmabuf_dirty’ [-Wmissing-prototypes]
drivers/gpu/drm/vmwgfx/vmwgfx_kms.c:1666:5: warning: no previous prototype for ‘vmw_du_update_layout’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
|
|
Remove unused function ttm_write_lock_downgrade() from
drm/ttm/ttm_lock.c.
This eliminates the following warning in drm/ttm/ttm_lock.c:
drivers/gpu/drm/ttm/ttm_lock.c:189:6: warning: no previous prototype for ‘ttm_write_lock_downgrade’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Mark functions as static because they are not used outside the file
drm/ttm/ttm_bo_util.c.
This eliminates the following warnings in drm/ttm/ttm_bo_util.c:
drivers/gpu/drm/ttm/ttm_bo_util.c:190:5: warning: no previous prototype for ‘ttm_mem_reg_ioremap’ [-Wmissing-prototypes]
drivers/gpu/drm/ttm/ttm_bo_util.c:222:6: warning: no previous prototype for ‘ttm_mem_reg_iounmap’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Mark function as static because it is not used outside file
drm/ttm/ttm_bo.c.
This eliminates the following warning in drm/ttm/ttm_bo.c:
drivers/gpu/drm/ttm/ttm_bo.c:960:5: warning: no previous prototype for ‘ttm_bo_move_buffer’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
This was introduced in:
commit 7c4a395ff8f441acb7876281c6777624e6410349
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Oct 9 19:17:56 2013 +0300
drm/i915: Don't re-compute pipe watermarks except for the affected pipe
and I missed fixing it in:
commit fec8cba306f974f3a4491176994de5d821273643
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Nov 27 11:10:26 2013 -0800
drm/i915: use crtc_htotal in watermark calculations to match fastboot v2
It's needed for ILK+ platforms to fastboot without crashing on a divide
by 0 after a DPMS on action.
Note: Ville mentioned in his review that this confusion seems to go
down to the original introduction of this code in
commit 801bcfffbb0721d7131e930f9a46103e539c43a4
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri May 31 10:08:35 2013 -0300
drm/i915: properly set HSW WM_PIPE registers
So it seems to have been missed both in the fastboot patch and in the
3d mode suppport (where only crtc_htotal reflects the real pipe
width).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add note based on Ville's review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
