| Age | Commit message (Collapse) | Author |
|---|
|
When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:
in usb_reset_and_verify_device():
udev->bos = NULL;
For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
from usb_unlocked_disable_lpm()
--> usb_disable_lpm()
--> usb_enable_lpm()
udev->bos->ss_cap->bU1devExitLat;
And it causes 'NULL pointer' and 'kernel panic':
[ 157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[ 158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[ 158.214954] Kernel panic - not syncing: Fatal exception
This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.
Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: Hans Yang <hansy@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On ixp4xx, the readl() function returns an 'unsigned long' output
when indirect I/O is used. This is unlike any other platform, and
it causes lots of harmless compiler warnings, such as:
drivers/ata/libahci.c: In function 'ahci_show_host_version':
drivers/ata/libahci.c:254:22: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat=]
drivers/block/mtip32xx/mtip32xx.c: In function 'mtip_hw_read_registers':
drivers/block/mtip32xx/mtip32xx.c:2602:31: warning: format '%X' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat=]
drivers/block/cciss.c: In function 'print_cfg_table':
drivers/block/cciss.c:3845:25: warning: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Wformat=]
This changes all six of the ixp4xx specific I/O read functions
to return the same types that we have in the normal asm/io.h,
to avoid the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
|
|
All ELAN hid devices seem to require the ALWAYS_POLL quirk. Let's use
this quirk for all devices from this vendor, rather than maintaining a
list of all its known product IDs.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds tlv bytes topology control creation and control load to
initialize kcontrol data. And this also adds the callbacks for
the these tlv byte kcontrols
Signed-off-by: Mythri P K <mythri.p.k@intel.com>
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds support to configure module parameter during module
initialization or after module init using set module param
required by the DSP firmware sequence.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some DSP modules has user configurable parameters, which are
required by some modules at module initialization.
To configure the module algorithm parameter during initialization
we add helpers here
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some DSP modules have user configurable parameters. These
parameters are required by modules in the following scenario
- during initialization
- after initialization using set parameter
This patch adds helper routine to set module parameters using
large config set IPC message and removes params to be passed as
init module routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On Skylake we can support upton 4DMICs on the PDM port, so update
the PCM capabilities accordingly
Also add a new DAI for DMIC pin which can be used for getting raw
DMIC data
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch is specifically for PCI support on the Versatile PB board using
a DT. Currently, the dynamic IRQ mapping is broken when using DTs. For
example, on QEMU, the SCSI driver is unable to request the IRQ. To fix
this issue, this patch replaces the current dynamic mechanism with a
static value as is done in the non-DT case.
Signed-off-by: Guillaume Delbergue <guillaume.delbergue@greensocs.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
|
|
The set_event_pid filter relies on attaching to the sched_switch and
sched_wakeup tracepoints to see if it should filter the tracing on schedule
tracepoints. By adding the callbacks to sched_wakeup, pids in the
set_event_pid file will trace the wakeups of those tasks with those pids.
But sched_wakeup_new and sched_waking were missed. These two should also be
traced. Luckily, these tracepoints share the same class as sched_wakeup
which means they can use the same pre and post callbacks as sched_wakeup
does.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Dmitry provided a syzkaller (http://github.com/google/syzkaller)
triggering a fault in sock_wake_async() when async IO is requested.
Said program stressed af_unix sockets, but the issue is generic
and should be addressed in core networking stack.
The problem is that by the time sock_wake_async() is called,
we should not access the @flags field of 'struct socket',
as the inode containing this socket might be freed without
further notice, and without RCU grace period.
We already maintain an RCU protected structure, "struct socket_wq"
so moving SOCKWQ_ASYNC_NOSPACE & SOCKWQ_ASYNC_WAITDATA into it
is the safe route.
It also reduces number of cache lines needing dirtying, so might
provide a performance improvement anyway.
In followup patches, we might move remaining flags (SOCK_NOSPACE,
SOCK_PASSCRED, SOCK_PASSSEC) to save 8 bytes and let 'struct socket'
being mostly read and let it being shared between cpus.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is a cleanup to make following patch easier to
review.
Goal is to move SOCK_ASYNC_NOSPACE and SOCK_ASYNC_WAITDATA
from (struct socket)->flags to a (struct socket_wq)->flags
to benefit from RCU protection in sock_wake_async()
To ease backports, we rename both constants.
Two new helpers, sk_set_bit(int nr, struct sock *sk)
and sk_clear_bit(int net, struct sock *sk) are added so that
following patch can change their implementation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent patches added basic support for the Apple NVMe controller but
still cause resets and data corruption on that particular controller
when a specific pattern of read/flush commands occurs. Limiting the
queue depth to 2 works around that issue.
This patch enforces that limit only for the Apple controller and is
considered a temporary fix until we find the root source of that
problem.
Signed-off-by: Stephan Günther <guenther@tum.de>
Signed-off-by: Maurice Leclaire <leclaire@in.tum.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
vmxnet3_drv does not check dma_addr with dma_mapping_error()
after mapping dma memory. The patch adds the checks and
tries to handle failures.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The N_X25 line discipline may access the previous line discipline's closed
and already-freed private data on open [1].
The tty->disc_data field _never_ refers to valid data on entry to the
line discipline's open() method. Rather, the ldisc is expected to
initialize that field for its own use for the lifetime of the instance
(ie. from open() to close() only).
[1]
[ 634.336761] ==================================================================
[ 634.338226] BUG: KASAN: use-after-free in x25_asy_open_tty+0x13d/0x490 at addr ffff8800a743efd0
[ 634.339558] Read of size 4 by task syzkaller_execu/8981
[ 634.340359] =============================================================================
[ 634.341598] BUG kmalloc-512 (Not tainted): kasan: bad access detected
...
[ 634.405018] Call Trace:
[ 634.405277] dump_stack (lib/dump_stack.c:52)
[ 634.405775] print_trailer (mm/slub.c:655)
[ 634.406361] object_err (mm/slub.c:662)
[ 634.406824] kasan_report_error (mm/kasan/report.c:138 mm/kasan/report.c:236)
[ 634.409581] __asan_report_load4_noabort (mm/kasan/report.c:279)
[ 634.411355] x25_asy_open_tty (drivers/net/wan/x25_asy.c:559 (discriminator 1))
[ 634.413997] tty_ldisc_open.isra.2 (drivers/tty/tty_ldisc.c:447)
[ 634.414549] tty_set_ldisc (drivers/tty/tty_ldisc.c:567)
[ 634.415057] tty_ioctl (drivers/tty/tty_io.c:2646 drivers/tty/tty_io.c:2879)
[ 634.423524] do_vfs_ioctl (fs/ioctl.c:43 fs/ioctl.c:607)
[ 634.427491] SyS_ioctl (fs/ioctl.c:622 fs/ioctl.c:613)
[ 634.427945] entry_SYSCALL_64_fastpath (arch/x86/entry/entry_64.S:188)
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
missing get_user()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit ab450605b35caa768ca33e86db9403229bf42be4.
In IPv6, we cannot inherit the dst of the original dst. ndisc packets
are IPv6 packets and may take another route than the original packet.
This patch breaks the following scenario: a packet comes from eth0 and
is forwarded through vxlan1. The encapsulated packet triggers an NS
which cannot be sent because of the wrong route.
CC: Jiri Benc <jbenc@redhat.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sound/soc/codecs/da7218.c:3214:9-10: WARNING: return of 0/1 in function 'da7218_volatile_register' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As hdac->num_nodes is unsigned we can not check if
snd_hdac_get_sub_nodes() has returned error or success. Lets have a
temporary int to check the error value.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The patch extends the family of SATA-to-USB JMicron adapters that need
FUA to be disabled and applies the same policy for uas driver.
See details in http://unix.stackexchange.com/questions/237204/
Signed-off-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Tested-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Like other buggy models that had their fixes [1], the touchscreen with
id 04f3:21b8 from ELAN Microelectronics needs the device-qualifier
quirk. Otherwise, it fails to respond, blocks the boot for a random
amount of time and pollutes dmesg with:
[ 2887.373196] usb 1-5: new full-speed USB device number 41 using xhci_hcd
[ 2889.502000] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2889.502005] usb 1-5: can't read configurations, error -71
[ 2889.654571] usb 1-5: new full-speed USB device number 42 using xhci_hcd
[ 2891.783438] usb 1-5: unable to read config index 0 descriptor/start: -71
[ 2891.783443] usb 1-5: can't read configurations, error -71
[1]: See commits c68929f, 876af5d, d749947, a32c99e and dc703ec.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-dapm
|
|
This commit at least doubles the maximum value for
completion_nsec. This helps in special cases where one wants/needs to
emulate an extremely slow I/O (for example to spot bugs).
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Arianna Avanzini <avanzini@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In single-queue (block layer) mode,the function null_rq_prep_fn stops
the device if alloc_cmd fails. Then, once stopped, the device must be
restarted on the next command completion, so that the request(s) for
which alloc_cmd failed can be requeued. Otherwise the device hangs.
Unfortunately, device restart is currently performed only for delayed
completions, i.e., in irqmode==2. This fact causes hangs, for the
above reasons, with the other irqmodes in combination with single-queue
block layer.
This commits addresses this issue by making sure that, if stopped, the
device is properly restarted for all irqmodes on completions.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Arianna AVanzini <avanzini@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
For the Timer IRQ mode (i.e., when command completions are delayed),
there is one timer for each CPU. Each of these timers
. has a completion queue associated with it, containing all the
command completions to be executed when the timer fires;
. is set, and a new completion-to-execute is inserted into its
completion queue, every time the dispatch code for a new command
happens to be executed on the CPU related to the timer.
This implies that, if the dispatch of a new command happens to be
executed on a CPU whose timer has already been set, but has not yet
fired, then the timer is set again, to the completion time of the
newly arrived command. When the timer eventually fires, all its queued
completions are executed.
This way of handling delayed command completions entails the following
problem: if more than one command completion is inserted into the
queue of a timer before the timer fires, then the expiration time for
the timer is moved forward every time each of these completions is
enqueued. As a consequence, only the last completion enqueued enjoys a
correct execution time, while all previous completions are unjustly
delayed until the last completion is executed (and at that time they
are executed all together).
Specifically, if all the above completions are enqueued almost at the
same time, then the problem is negligible. On the opposite end, if
every completion is enqueued a while after the previous completion was
enqueued (in the extreme case, it is enqueued only right before the
timer would have expired), then every enqueued completion, except for
the last one, experiences an inflated delay, proportional to the number
of completions enqueued after it. In the end, commands, and thus I/O
requests, may be completed at an arbitrarily lower rate than the
desired one.
This commit addresses this issue by replacing per-CPU timers with
per-command timers, i.e., by associating an individual timer with each
command.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Arianna Avanzini <avanzini@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc fixes from Ohad Ben-Cohen:
"Two one-liners coming from Suman and Arnd"
* tag 'remoteproc-4.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc: fix memory leak of remoteproc ida cache layers
remoteproc: avoid stack overflow in debugfs file
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.4-rc3
Here are some device-id fixes that remove a HID device from cp210x, and
adds support for another Infineon flash-loader device. The flash-loader
device presents itself as a CDC-ACM device even though it is clearly
not, so we need to blacklist it in the cdc-acm driver as well.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.4-rc3
Here's our second round of fixes. Some of the bugs are pretty old like
the one on pxa27x suspend implementation.
The most important part is a randbuild warning fix on MUSB CPPI DMA
engine by Arnd, a couple fixes by Felipe Tonello on f_midi (first one
makes sure we only transmit on enabled ep IN while second plugs a memory
leak) and a NULL pointer dereference fix on renesas usbhs.
Note that we also have a new compatible string being added for the MXS
PHY.
|
|
We have been returning success even if snd_soc_card_jack_new() fails.
Lets check the return value and return error if it fails.
Fixes: 12cc6d1dca4d ("ASoC: tegra_alc5632: Register jacks at the card level")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 1fb34b48361e ('ASoC: sun4i: Implement MIC1 capture') added back some
code that disregards the clk_set_rate error code and always returns
-EINVAL. Fix that and return the code in order to have more clue about
what's going on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The comment is misleading on how we should support external power amps, and
the variable is not used and generates a warning.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When switching between two clock sources using the FLL freerun to smooth
the transition we should wait 32uS after putting the FLL into freerun
before we proceed. In practice we appear to be getting enough delay from
the surrounding code, but better to make it explicit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds missing check of snd_soc_of_get_dai_name().
It might not be able to use sound card, because it might returns
-EPROBE_DEFER.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
drv pointer should be "base + offset" instead of
"current + offset". This patch fixup this issue, otherwise
third and subsequent pointer will be broken
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When doing the initial setup both the hclk and the aclk need to be
enabled otherwise the board will simply hang. This only occurs when
building the vop driver as a module, when its built-in the initial setup
happens to run before the clock framework shuts of unused clocks
(including the aclk).
While there also switch to doing prepare and enable in one step rather
then separate steps to reduce the amount of code required.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Romain Perier <romain.perier@gmail.com>
|
|
When building for SH7734:
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:2: error: '_GP_DATA' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:586:1: error: macro "_GP_DATA" passed 5 arguments, but takes just 4
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:1: error: macro "_GP_INOUTSEL" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:53: error: '_GP_INOUTSEL' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2389:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:1: error: macro "_GP_INDT" passed 5 arguments, but takes just 4
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:47: error: '_GP_INDT' undeclared here (not in a function)
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: initialization makes integer from pointer without a cast [enabled by default]
drivers/pinctrl/sh-pfc/pfc-sh7734.c:2416:2: warning: (near initialization for '(anonymous)[0]') [enabled by default]
...
Add the missing "cfg" macro parameters to the sh7734-specific
_GP_DATA(), _GP_INOUTSEL(), and _GP_INDT() macros to fix this.
Fixes: 22768fc60abbf58b ("pinctrl: sh-pfc: Add macros defining GP ports with config flags")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We have relied upon the sole caller (wait_ioctl) validating the timeout
argument. However, when waiting for multiple requests I forgot to ensure
that the timeout was still positive on the later requests. This is more
simply done inside __i915_wait_request.
Fixes regression introduced in
commit b47161858ba13c9c7e03333132230d66e008dd55
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:17 2015 +0100
drm/i915: Implement inter-engine read-read optimisations
The impact of the regression is 1 jiffie for each extra active ring for
a wait_ioctl with a timeout -- I don't think anyone has noticed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448544702-5594-1-git-send-email-chris@chris-wilson.co.uk
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
It's supposed to be equivalent with CX20724.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The numbers aren't always linear, just like in the real world.
Correct to the right numbers stated in the datasheet (although we
can't trust the datasheet as well).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.4 cycle.
Some of these were waiting for various code to hit during the merge
window - others have simply shown up recently.
* Dummy - fix a bug introduced recently that stops events actually
reaching userspace.
* Lidar - return -EINVAL on getting a report of an invalid reading from
the device. This could mean that nothing is in range, or something
else has gone wrong. Basically it tells us nothing useful beyond the
reading is bogus and should be ignored.
* apds9660 - make sure to call pm_runtime_mark_last_busy when reading
from the device to avoid a premature disabling of the power.
* core - fix up a few missues of the WARN macro.
* spmi-vadc - fix a missing of_node_put when breaking out of
a for_each_available_child_of_node loop.
The dummy driver is going to result in a slightly interesting
merge when this meets the togreg branch as that driver has graduated
from staging in the meantime. I'll send an email in reply to that
pull request highlighting this as well.
|
|
The mpt2sas driver was recently folded into mpt3sas to reduce code
duplication.
To avoid problems for people that only have CONFIG_SCSI_MPT2SAS in their
.config we introduce a dummy option that will select MPT3SAS if MPT2SAS
was previously enabled.
This is a temporary measure and we will deprecate this config option in
4.6.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: James Bottomley <James.Bottomley@hansenpartnership.com>
CC: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Avoid that kmemleak reports the following memory leak if a
SCSI LLD calls scsi_host_alloc() and scsi_host_put() but neither
scsi_host_add() nor scsi_host_remove(). The following shell
command triggers that scenario:
for ((i=0; i<2; i++)); do
srp_daemon -oac |
while read line; do
echo $line >/sys/class/infiniband_srp/srp-mlx4_0-1/add_target
done
done
unreferenced object 0xffff88021b24a220 (size 8):
comm "srp_daemon", pid 56421, jiffies 4295006762 (age 4240.750s)
hex dump (first 8 bytes):
68 6f 73 74 35 38 00 a5 host58..
backtrace:
[<ffffffff8151014a>] kmemleak_alloc+0x7a/0xc0
[<ffffffff81165c1e>] __kmalloc_track_caller+0xfe/0x160
[<ffffffff81260d2b>] kvasprintf+0x5b/0x90
[<ffffffff81260e2d>] kvasprintf_const+0x8d/0xb0
[<ffffffff81254b0c>] kobject_set_name_vargs+0x3c/0xa0
[<ffffffff81337e3c>] dev_set_name+0x3c/0x40
[<ffffffff81355757>] scsi_host_alloc+0x327/0x4b0
[<ffffffffa03edc8e>] srp_create_target+0x4e/0x8a0 [ib_srp]
[<ffffffff8133778b>] dev_attr_store+0x1b/0x20
[<ffffffff811f27fa>] sysfs_kf_write+0x4a/0x60
[<ffffffff811f1e8e>] kernfs_fop_write+0x14e/0x180
[<ffffffff81176eef>] __vfs_write+0x2f/0xf0
[<ffffffff811771e4>] vfs_write+0xa4/0x100
[<ffffffff81177c64>] SyS_write+0x54/0xc0
[<ffffffff8151b257>] entry_SYSCALL_64_fastpath+0x12/0x6f
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Dmitry V. Krivenok <krivenok.dmitry@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Avoid the sticky preferred mode bit by using the no-merge version of the
function (this allows gnome-shell to resize to lower resolutions than
the default resolution)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration,
so a break out of the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull mn10300 fix from Guenter Roeck:
"A single patch to fix mn10300 build failures"
* tag 'mn10300-for-linus-v4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
mn10300: Select CONFIG_HAVE_UID16 to fix build failure
|
|
Remove the "not" before "cannot".
I am fixing the comment block style while I am here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Signed-off-by: Dmitry V. Krivenok <krivenok.dmitry@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
In order to check for overlapping reserved memory regions, we first need
to sort the array of memory regions. This is implemented using sort(),
and a custom comparison function __rmem_cmp().
Unfortunatley __rmem_cmp() doesn't work in all cases. Because the two
base values are phys_addr_t, they may be u64 on some platforms, in which
case subtracting one from the other and then (implicitly) casting to int
does not give us the -ve/0/+ve value we need.
This leads to incorrect reports about overlaps, eg:
ibm,slw-image@1ffe600000 (0x0000001ffe600000--0x0000001ffe700000) overlaps with
ibm,firmware-allocs-memory@1000000000 (0x0000001000000000--0x0000001000dc0200)
Fix it by just doing the standard double if and return 0 logic.
Fixes: ae1add247bf8 ("of: Check for overlap in reserved memory regions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"I found two minor bugs while doing development on the ring buffer
code.
The first is something that's been there since its creation. If a
reader reads a page out of the ring buffer before there's any events
on it, it can get an out of date timestamp for that event. It may be
off by a few microseconds, more if the first event gets discarded.
The fix was to only update the reader time stamp when it actually sees
an event on the page, instead of just reading the timestamp from the
page even if it has no events on it. That timestamp is still volatile
until an event is present.
The second bug is more recent. Instead of passing around parameters a
descriptor was made and the parameters are passed via a single
descriptor. This simplified the code a bit. But there was one place
that expected the parameter to be passed by value not reference (which
a descriptor now does). And it added to the length of the event,
which may be ignored later, but the length should not have been
increased. The only real problem with this bug is that it may
allocate more than was needed for the event"
* tag 'trace-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ring-buffer: Put back the length if crossed page with add_timestamp
ring-buffer: Update read stamp with first real commit on page
|
