| Age | Commit message (Collapse) | Author |
|---|
|
SD spec v5.1 adds discard support. The flows and commands are similar to
mmc, so just set the discard arg in CMD38.
A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313)
is set in the SD_STATUS register. If the card does not support discard,
the host shall not issue DISCARD command, but ERASE command instead.
Post the DISCARD operation, the card may de-allocate the discarded
blocks partially or completely. So the host mustn't make any assumptions
concerning the content of the discarded region. This is unlike ERASE
command, in which the region is guaranteed to contain either '0's or
'1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr
register.
One more important difference compared to ERASE is the busy timeout
which we will address on the next patch.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After system suspend, CQE is in cqhci_off state, which set the HALT bit, make
CQE in HALT state. If the SoC do not power down the USDHC module, then when
system resume back, this bit keep the same, still set. Though there is a
sdhci reset during sdhci_resume_host(), but this reset do not impact the
CQE part, so need to clear this bit when enable CQE, otherwise CQE will
stuck in the first CMDQ request after system resume back.
Find this issue on NXP i.MX845s-mek board
[ 105.919862] mmc2: cqhci: timeout for tag 6
[ 105.923965] mmc2: cqhci: ============ CQHCI REGISTER DUMP ===========
[ 105.930407] mmc2: cqhci: Caps: 0x0000310a | Version: 0x00000510
[ 105.936847] mmc2: cqhci: Config: 0x00001001 | Control: 0x00000001
[ 105.943286] mmc2: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006
[ 105.949725] mmc2: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000
[ 105.956164] mmc2: cqhci: TDL base: 0x7809b000 | TDL up32: 0x00000000
[ 105.962604] mmc2: cqhci: Doorbell: 0x00000040 | TCN: 0x00000000
[ 105.969043] mmc2: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x00000000
[ 105.975483] mmc2: cqhci: Task clr: 0x00000000 | SSC1: 0x00011000
[ 105.981922] mmc2: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000000
[ 105.988362] mmc2: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000
[ 105.994801] mmc2: cqhci: Resp idx: 0x00000000 | Resp arg: 0x00000000
[ 106.001240] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 106.007680] mmc2: sdhci: Sys addr: 0xb2b37800 | Version: 0x00000002
[ 106.014120] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001
[ 106.020560] mmc2: sdhci: Argument: 0x00010000 | Trn mode: 0x00000013
[ 106.026999] mmc2: sdhci: Present: 0x01f88008 | Host ctl: 0x00000030
[ 106.033439] mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080
[ 106.039878] mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000000f
[ 106.046318] mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000
[ 106.052757] mmc2: sdhci: Int enab: 0x107f4000 | Sig enab: 0x107f4000
[ 106.059196] mmc2: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000502
[ 106.065635] mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x8000b407
[ 106.072075] mmc2: sdhci: Cmd: 0x00000d1a | Max curr: 0x00ffffff
[ 106.078514] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0x31360181
[ 106.084954] mmc2: sdhci: Resp[2]: 0x44473430 | Resp[3]: 0x00450100
[ 106.091392] mmc2: sdhci: Host ctl2: 0x00000008
[ 106.095836] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x7804b208
[ 106.102274] mmc2: sdhci: ============================================
[ 106.108785] mmc2: running CQE recovery
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
the response type of CMD6 is R1B, when the first CMD6 gets response
CRC error, do retry may get timeout error due to card may still in
busy state, which cause this retry make no sense.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf annotate:
Wei Li:
- Fix getting source line failure
perf script:
Andi Kleen:
- Handle missing fields with -F +...
perf data:
Jiri Olsa:
- Prep work to support per-cpu files in a directory.
Intel PT:
Adrian Hunter:
- Improve thread_stack__no_call_return()
- Hide x86 retpolines in thread stacks.
- exported SQL viewer refactorings, new 'top calls' report..
Alexander Shishkin:
- Copy parent's address filter offsets on clone
- Fix address filters for vmas with non-zero offset. Applies to
ARM's CoreSight as well.
python scripts:
Tony Jones:
- Python3 support for several 'perf script' python scripts.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf report:
He Kuang:
- Don't shadow inlined symbol with different addr range.
perf script:
Jiri Olsa:
- Allow +- operator to ask for -F to add/remove fields to
the default set, for instance to ask for the removal of the
'cpu' field in tracepoint events, adding 'period' to that
kind of events, etc.
perf test:
Thomas Richter:
- Fix scheduler tracepoint signedness of COMM fields failure of
'evsel-tp-sched' test on s390 and other arches.
Tommi Rantala:
- Skip trace+probe_vfs_getname.sh when 'perf trace' is not built.
perf trace:
Arnaldo Carvalho de Melo:
- Add initial BPF map dumper, initially just for the current, minimal
needs of the augmented_raw_syscalls BPF example used to collect
pointer args payloads that uses BPF maps for pid and syscall filtering,
but will in time have features similar to 'perf stat' --interval-print,
--interval-clear, ways to signal from a BPF event that a specific
map (or range of that map) should be printed, optionally as a
histogram, etc.
General:
Jiri Olsa:
- Add CPU and NUMA topologies classes for further reuse, fixing some
issues in the process.
- Fixup some warnings and debug levels.
- Make rm_rf() remove single file, not just directories.
Documentation:
Jonas Rabenstein:
- Fix HEADER_CMDLINE description in perf.data documentation.
- Fix documentation of the Flags section in perf.data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Shrink struct lock_class_key; we never store anything in subkeys[], we
only use the addresses.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
And move the whole lot under CONFIG_DEBUG_LOCKDEP.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Make sure that the lockdep_register_key() and lockdep_unregister_key()
code is tested when running the lockdep tests.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-24-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Apparently the execute bits were set for the tests/*.sh scripts on my
test setup but these are not set in the kernel tree. Fix this by adding
the interpreter path in front of the script paths.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Fixes: 5ecb8e94b494 ("tools/lib/lockdep/tests: Improve testing accuracy") # v5.0-rc1
Link: https://lkml.kernel.org/r/20190214230058.196511-23-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The following commit:
87915adc3f0a ("workqueue: re-add lockdep dependencies for flushing")
improved deadlock checking in the workqueue implementation. Unfortunately
that patch also introduced a few false positive lockdep complaints.
This patch suppresses these false positives by allocating the workqueue mutex
lockdep key dynamically.
An example of a false positive lockdep complaint suppressed by this patch
can be found below. The root cause of the lockdep complaint shown below
is that the direct I/O code can call alloc_workqueue() from inside a work
item created by another alloc_workqueue() call and that both workqueues
share the same lockdep key. This patch avoids that that lockdep complaint
is triggered by allocating the work queue lockdep keys dynamically.
In other words, this patch guarantees that a unique lockdep key is
associated with each work queue mutex.
======================================================
WARNING: possible circular locking dependency detected
4.19.0-dbg+ #1 Not tainted
fio/4129 is trying to acquire lock:
00000000a01cfe1a ((wq_completion)"dio/%s"sb->s_id){+.+.}, at: flush_workqueue+0xd0/0x970
but task is already holding lock:
00000000a0acecf9 (&sb->s_type->i_mutex_key#14){+.+.}, at: ext4_file_write_iter+0x154/0x710
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&sb->s_type->i_mutex_key#14){+.+.}:
down_write+0x3d/0x80
__generic_file_fsync+0x77/0xf0
ext4_sync_file+0x3c9/0x780
vfs_fsync_range+0x66/0x100
dio_complete+0x2f5/0x360
dio_aio_complete_work+0x1c/0x20
process_one_work+0x481/0x9f0
worker_thread+0x63/0x5a0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
-> #1 ((work_completion)(&dio->complete_work)){+.+.}:
process_one_work+0x447/0x9f0
worker_thread+0x63/0x5a0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
-> #0 ((wq_completion)"dio/%s"sb->s_id){+.+.}:
lock_acquire+0xc5/0x200
flush_workqueue+0xf3/0x970
drain_workqueue+0xec/0x220
destroy_workqueue+0x23/0x350
sb_init_dio_done_wq+0x6a/0x80
do_blockdev_direct_IO+0x1f33/0x4be0
__blockdev_direct_IO+0x79/0x86
ext4_direct_IO+0x5df/0xbb0
generic_file_direct_write+0x119/0x220
__generic_file_write_iter+0x131/0x2d0
ext4_file_write_iter+0x3fa/0x710
aio_write+0x235/0x330
io_submit_one+0x510/0xeb0
__x64_sys_io_submit+0x122/0x340
do_syscall_64+0x71/0x220
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Chain exists of:
(wq_completion)"dio/%s"sb->s_id --> (work_completion)(&dio->complete_work) --> &sb->s_type->i_mutex_key#14
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&sb->s_type->i_mutex_key#14);
lock((work_completion)(&dio->complete_work));
lock(&sb->s_type->i_mutex_key#14);
lock((wq_completion)"dio/%s"sb->s_id);
*** DEADLOCK ***
1 lock held by fio/4129:
#0: 00000000a0acecf9 (&sb->s_type->i_mutex_key#14){+.+.}, at: ext4_file_write_iter+0x154/0x710
stack backtrace:
CPU: 3 PID: 4129 Comm: fio Not tainted 4.19.0-dbg+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
dump_stack+0x86/0xc5
print_circular_bug.isra.32+0x20a/0x218
__lock_acquire+0x1c68/0x1cf0
lock_acquire+0xc5/0x200
flush_workqueue+0xf3/0x970
drain_workqueue+0xec/0x220
destroy_workqueue+0x23/0x350
sb_init_dio_done_wq+0x6a/0x80
do_blockdev_direct_IO+0x1f33/0x4be0
__blockdev_direct_IO+0x79/0x86
ext4_direct_IO+0x5df/0xbb0
generic_file_direct_write+0x119/0x220
__generic_file_write_iter+0x131/0x2d0
ext4_file_write_iter+0x3fa/0x710
aio_write+0x235/0x330
io_submit_one+0x510/0xeb0
__x64_sys_io_submit+0x122/0x340
do_syscall_64+0x71/0x220
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/r/20190214230058.196511-20-bvanassche@acm.org
[ Reworked the changelog a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
A shortcoming of the current lockdep implementation is that it requires
lock keys to be allocated statically. That forces all instances of lock
objects that occur in a given data structure to share a lock key. Since
lock dependency analysis groups lock objects per key sharing lock keys
can cause false positive lockdep reports. Make it possible to avoid
such false positive reports by allowing lock keys to be allocated
dynamically. Require that dynamically allocated lock keys are
registered before use by calling lockdep_register_key(). Complain about
attempts to register the same lock key pointer twice without calling
lockdep_unregister_key() between successive registration calls.
The purpose of the new lock_keys_hash[] data structure that keeps
track of all dynamic keys is twofold:
- Verify whether the lockdep_register_key() and lockdep_unregister_key()
functions are used correctly.
- Avoid that lockdep_init_map() complains when encountering a dynamically
allocated key.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-19-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
class keys
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-18-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Debugging lockdep data structure inconsistencies is challenging. Add
code that verifies data structure consistency at runtime. That code is
disabled by default because it is very CPU intensive.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-17-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
A previous patch introduced a lock chain leak. Fix that leak by reusing
lock chains that have been freed.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-16-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Reflect that add_chain_cache() is always called with the graph lock held.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-15-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch does not change any functionality but makes the next patch in
this series easier to read.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-14-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Instead of abandoning elements of list_entries[] that are no longer in
use, make alloc_list_entry() reuse array elements that have been freed.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-13-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Instead of leaving lock classes that are no longer in use in the
lock_classes array, reuse entries from that array that are no longer in
use. Maintain a linked list of free lock classes with list head
'free_lock_class'. Only add freed lock classes to the free_lock_classes
list after a grace period to avoid that a lock_classes[] element would
be reused while an RCU reader is accessing it. Since the lockdep
selftests run in a context where sleeping is not allowed and since the
selftests require that lock resetting/zapping works with debug_locks
off, make the behavior of lockdep_free_key_range() and
lockdep_reset_lock() depend on whether or not these are called from
the context of the lockdep selftests.
Thanks to Peter for having shown how to modify get_pending_free()
such that that function does not have to sleep.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-12-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
synchronize_sched() has been removed recently. Update the comments that
refer to synchronize_sched().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Fixes: 51959d85f32d ("lockdep: Replace synchronize_sched() with synchronize_rcu()") # v5.0-rc1
Link: https://lkml.kernel.org/r/20190214230058.196511-11-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The patch that frees unused lock classes will modify the behavior of
lockdep_free_key_range() and lockdep_reset_lock() depending on whether
or not these functions are called from the context of the lockdep
selftests. Hence make it easy to detect whether or not lockdep code
is called from the context of a lockdep selftest.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-10-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch does not change the behavior of these functions but makes the
patch that frees unused lock classes easier to read.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-9-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch does not change any functionality. A later patch will reuse
lock classes that have been freed. In combination with that patch this
patch wil have the effect of initializing lock class order lists once
instead of every time a lock class structure is reinitialized.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-8-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Make sure that all lock order entries that refer to a class are removed
from the list_entries[] array when a kernel module is unloaded.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-7-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch does not change any functionality but makes the patch that
frees lock classes that are no longer in use easier to read.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-6-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Make sure that add_chain_cache() returns 0 and does not modify the
chain hash if nr_chain_hlocks == MAX_LOCKDEP_CHAIN_HLOCKS before this
function is called.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-5-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Lock chains are only tracked with CONFIG_PROVE_LOCKING=y. Do not report
the memory required for the lock chain array if CONFIG_PROVE_LOCKING=n.
See also commit:
ca58abcb4a6d ("lockdep: sanitise CONFIG_PROVE_LOCKING")
Include the size of the chain_hlocks[] array.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-4-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Change the sizeof(array element time) * (array size) expressions into
sizeof(array). This fixes the size computations of the classhash_table[]
and chainhash_table[] arrays.
The reason is that commit:
a63f38cc4ccf ("locking/lockdep: Convert hash tables to hlists")
changed the type of the elements of that array from 'struct list_head' into
'struct hlist_head'.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-3-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use %zu to format size_t instead of %lu to avoid that the compiler
complains about a mismatch between format specifier and argument on
32-bit systems.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-2-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
With the > 4 nesting levels case handled by the commit:
d682b596d993 ("locking/qspinlock: Handle > 4 slowpath nesting levels")
the BUG_ON() call in encode_tail() will never actually be triggered.
Remove it.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1551057253-3231-1-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Effective revert commit:
87709e28dc7c ("fs/locks: Use percpu_down_read_preempt_disable()")
This is causing major pain for PREEMPT_RT.
Sebastian did a lot of lockperf runs on 2 and 4 node machines with all
preemption modes (PREEMPT=n should be an obvious NOP for this patch
and thus serves as a good control) and no results showed significance
over 2-sigma (the PREEMPT=n results were almost empty at 1-sigma).
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
On big endian arm64 kernels, the xchacha20-neon and xchacha12-neon
self-tests fail because hchacha_block_neon() outputs little endian words
but the C code expects native endianness. Fix it to output the words in
native endianness (which also makes it match the arm32 version).
Fixes: cc7cf991e9eb ("crypto: arm64/chacha20 - add XChaCha20 support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The change to encrypt a fifth ChaCha block using scalar instructions
caused the chacha20-neon, xchacha20-neon, and xchacha12-neon self-tests
to start failing on big endian arm64 kernels. The bug is that the
keystream block produced in 32-bit scalar registers is directly XOR'd
with the data words, which are loaded and stored in native endianness.
Thus in big endian mode the data bytes end up XOR'd with the wrong
bytes. Fix it by byte-swapping the keystream words in big endian mode.
Fixes: 2fe55987b262 ("crypto: arm64/chacha - use combined SIMD/ALU routine for more speed")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add AES crypto HW acceleration for Exynos5433, with the help of SlimSSS IP.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Document DT bindings for crypto Samsung Exynos5433 SlimSSS (Slim Security
SubSystem) IP.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add an of_node_put when a tested device node is not available.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
identifier f;
local idexpression e;
expression x;
@@
e = f(...);
... when != of_node_put(e)
when != x = e
when != e = x
when any
if (<+...of_device_is_available(e)...+>) {
... when != of_node_put(e)
(
return e;
|
+ of_node_put(e);
return ...;
)
}
// </smpl>
Fixes: 5343e674f32fb ("crypto4xx: integrate ppc4xx-rng into crypto4xx")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The cavium/zip implementation of the deflate compression algorithm is
incorrectly being registered under the generic driver name, which
prevents the generic implementation from being registered with the
crypto API when CONFIG_CRYPTO_DEV_CAVIUM_ZIP=y. Similarly the lzs
algorithm (which does not currently have a generic implementation...)
is incorrectly being registered as lzs-generic.
Fix the naming collision by adding a suffix "-cavium" to the
cra_driver_name of the cavium/zip algorithms.
Fixes: 640035a2dc55 ("crypto: zip - Add ThunderX ZIP driver core")
Cc: Mahipal Challa <mahipalreddy2006@gmail.com>
Cc: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*sgl) + sizeof(sgl->sg[0]) * (MAX_SGL_ENTS + 1)
to :
struct_size(sgl, sg, MAX_SGL_ENTS + 1)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
unlikely has already included in IS_ERR(), so just
remove redundant likely/unlikely annotation.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix bug "s5p-sss crypto driver doesn't set next AES-CBC IV". While at this,
fix also AES-CTR mode. Tested on Odroid U3 with Eric Biggers branch
"iv-out-testing".
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
1-block SSE2 variant of poly1305 stores variables s1..s4 containing key
material on the stack. This commit adds missing zeroing of the stack
memory. Benchmarks show negligible performance hit (tested on i7-3770).
Signed-off-by: Tommi Hirvola <tommi@hirvola.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When generating a split key or hashing the key, DMA mapping the key
buffers coming directly from user is incorrect, since they are
not guaranteed to be DMAable.
Update driver to first copy user-provided key in the output buffer
("key_out") and then use this buffer for in-place computation
(split key generation, respectively key hashing).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix a side effect of adding xcbc support, which leads to DMA mapping the
key twice.
Fixes: 12b8567f6fa4 ("crypto: caam - add support for xcbc(aes)")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When driver started using state->caam_ctxt for storing both running hash
and final hash, it was not updated to handle different DMA unmap
lengths.
Cc: <stable@vger.kernel.org> # v4.19+
Fixes: c19650d6ea99 ("crypto: caam - fix DMA mapping of stack memory")
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
BCM63XX (MIPS) does not use device tree, so there cannot be any
of_device_id, causing the driver to fail on probe:
[ 0.904564] bcm2835-rng: probe of bcm63xx-rng failed with error -22
Fix this by checking for match data only if we are probing from device
tree.
Fixes: 8705f24f7b57 ("hwrng: bcm2835 - Enable BCM2835 RNG to work on BCM63xx platforms")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Replace hard coded AES block size with define.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is no need to have the struct stm32_hash_dev *hdev static
since new value always be assigned before use it.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fixed Traffic Stall caused by
- Subcommands except last should have more bit set
- For esn case subcommand is required for linear skb only
- Also Optimized is_eth_imm usage
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/crypto/marvell/cipher.c: In function 'mv_cesa_skcipher_dma_req_init':
drivers/crypto/marvell/cipher.c:325:15: warning:
variable 'ivsize' set but not used [-Wunused-but-set-variable]
It's not used any more after 0c99620f0ac1 ("crypto: marvell - Use an unique
pool to copy results of requests")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
