| Age | Commit message (Collapse) | Author |
|---|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function 'mlxsw_sp_port_get_link_ksettings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3062:5: warning:
variable 'autoneg_status' set but not used [-Wunused-but-set-variable]
It's not used since commit 475b33cb66c9 ("mlxsw: spectrum: Remove unsupported
eth_proto_lp_advertise field in PTYS")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roopa Prabhu says:
====================
vxlan: create and changelink extack support
This series adds extack support to changelink paths.
In the process re-factors flag sets to a separate helper.
Also adds some changelink testcases to rtnetlink.sh
(This series was initially part of another series that
tried to support changelink for more attributes.
But after some feedback from sabrina, i have dropped the
'support changelink for more attributes' part because some
of them cannot be supported today or may require additional
use-case handling code. These can be done separately
as and when we see the need for it.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends rtnetlink.sh to cover some vxlan flag
netlink attribute sets.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds extack coverage in vxlan link
create and changelink paths. Introduces a new helper
vxlan_nl2flags to consolidate flag attribute validation.
thanks to Johannes Berg for some tips to construct the
generic vxlan flag extack strings.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
devlink: make ethtool compat reliable
This is a follow up to the series which added device flash
updates via devlink. I went with the approach of adding a
new NDO in the end. It seems to end up looking cleaner.
First patch removes the option to build devlink as a module.
Users can still decide to not build it, but the module option
ends up not being worth the maintenance cost.
Next two patches add a NDO which can be used to ask the driver
to return a devlink instance associated with a given netdev,
instead of iterating over devlink ports. Drivers which implement
this NDO must take into account the potential impact on the
visibility of the devlink instance.
With the new NDO in place we can remove NFP ethtool flash update
code.
Fifth patch makes sure we hold a reference to dev while
callbacks are active.
Last but not least the NULL-check of devlink->ops is moved
to instance allocation time.
Last but not least missing checks for devlink->ops are added.
There is currently no driver registering devlink without ops,
so can just fix this in -next.
v2 (Michal): add netdev_to_devlink() in patch 3.
v3 (Florian):
- add missing checks for devlink->ops;
- move locking/holding into devlink_compat_ functions.
v4 (Jiri):
- hold devlink_mutex around callbacks (patch 2);
- require non-NULL ops (patch 6).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 76726ccb7f46 ("devlink: add flash update command") and
commit 2d8dc5bbf4e7 ("devlink: Add support for reload")
access devlink ops without NULL-checking. There is, however, no
driver which would pass in NULL ops, so let's just make that
a requirement. Remove the now unnecessary NULL-checking.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ethtool is calling into devlink compat code make sure we have
a reference on the netdevice on which the operation was invoked.
v3: move the hold/lock logic into devlink_compat_* functions (Florian)
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that devlink fallback will be called reliably, we can remove
the ethtool flashing code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support getting devlink instance from a new NDO.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of iterating over all devlink ports add a NDO which
will return the devlink instance from the driver.
v2: add the netdev_to_devlink() helper (Michal)
v3: check that devlink has ops (Florian)
v4: hold devlink_mutex (Jiri)
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Being able to build devlink as a module causes growing pains.
First all drivers had to add a meta dependency to make sure
they are not built in when devlink is built as a module. Now
we are struggling to invoke ethtool compat code reliably.
Make devlink code built-in, users can still not build it at
all but the dynamically loadable module option is removed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The *i2c and *i2c_8606 are no longer used since this driver was converted
to use regmap helpers. The *chip and *regulator are not really required.
So remove these unused fields.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set volt_table filed then we can use regulator_list_voltage_table.
Since we have volt_table setting, now we can remove vol_table from
struct pm8607_regulator_info.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
They should never change, make them const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver uses regulator_get/set_voltage_sel_regmap so it does not use
vsel_shift. Actually, vsel_shift can be calculated by vsel_mask setting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that all users of struct inet_frag_queue have been converted
to use 'rb_fragments', remove the unused 'fragments' field.
Build with `make allyesconfig` succeeded. ip_defrag selftest passed.
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/recv.c: In function 'ath_rx_count_airtime':
drivers/net/wireless/ath/ath9k/recv.c:1010:18: warning:
variable 'acq' set but not used [-Wunused-but-set-variable]
It's not used after 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling
and airtime APIs"). Also remove related variables.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
SPUR DOWN field returns spurup instead of spurdown.
Signed-off-by: Andrea Greco <a.greco@4sigma.it>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since ath9k reports airtime usage directly using the
ieee80211_report_airtime() callback, it shouldn't also report it using the
tx_time in status. Make sure the field is zeroed before TX status is
reported to avoid spurious airtime being accounted by bits being left over
from earlier uses of the cb.
Fixes: 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
WCN3990 firmware versions WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 & onwards
supports maximum 33 peers including self peer. To support maximum peers,
send updated peer param to firmware during initialization.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The calibration data fetch will trigger sdio error, then sdio will
become fail untill reboot system.
If happens when run ifconfig wlan down, then ifconfig wlan up will
fail untill reboot system.Remove it fix the ifconfig wlan issue.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.
Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da49733e "ath10k: wmi: add management tx by reference support over wmi"
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware does not provide RSSI value to the host, it's only set to
zero. In that case don't report the value to mac80211. One risk here is that
value zero might be a valid value with other firmware, currently there's no way
to detect that.
Without the fix, the rssi value indicated by iw changes between the actual
value and -95.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The target device needs to be reset during power_down(), otherwise only the
first power_up() will work. And as ath10k calls power_up() during driver
initialisation the driver would be otherwise unusable.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware may turn it on based on scratch registers so disable the
firmware log to avoid that.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The SDIO firmware does not allow transmitting packets with the
reduced tx completion HI_ACS option. SDIO firmware uses 1544 as
alternate credit size, which is not big enough for the maximum sized
mac80211 frames. Disable both these HI_ACS flags for SDIO.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a theoretical fix, the issue is found in code review.
When adding the host memory chunks into wmi-tlv init command,
there is no separate tlv header for each host memory chunk
in the struct array, which breaches the convention between
host and firmware, will result in mismatch between the two.
To fix this issue, add separate tlv headers for the host
memory chunks in wmi-tlv init command.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently after enabling the WMI debug logging,
there is no detail printed about the param id
and the param value for the pdev, vdev and
peer params which are set.
Enhance the WMI logging to print the param id
and the param value for pdev, vdev and peer set
param wmi commands.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "data" tx completion event. Host extracts ack rssi
values of data packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "management" tx completion event. Host extracts ack
rssi values of management packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When the driver receives the tx completion of the
descriptor over ce, it clears the nbytes configured
for that particular descriptor. WCN3990 uses ce
descriptors with 64-bit address.
Currently during handling the tx completion of the
descriptors, the nbytes are accessed from the descriptors
using ce_desc for 32-bit targets. This will lead to clearing
of memory at incorrect offset if DMA MASK is set to greater
than 32 bits.
Attach different ce tx copy completed handler for targets
using address above 32-bit address.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
LS3 has a selectable current limit.
Change units to microamp in the example.
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document device-tree settings of the load-switch LS2
in the tps65218 device.
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence it is
removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The module version is unlikely to be updated, use kernel version should be
enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current code does not really avoid array access out of bounds,
fix it by add checking for pdata->slew_rate.
If pdata->slew_rate is too big, it's a bug in pdata that needs fix.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Setup .vsel_reg and .vsel_mask then we can use the standard
set/get_voltage_sel_regmap helpers to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The wm831x_dcdc_ilim entries needs to be uA because it is used to compare
with min_uA and max_uA.
While at it also make the array const and change to use unsigned int.
Fixes: e4ee831f949a ("regulator: Add WM831x DC-DC buck convertor support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver is for a newer generation of 2x2 MediaTek 802.11n chipsets.
MT7603E is a PCIe chip.
MT7628 and MT7688 are MIPS SoC devices with built-in WLAN.
MT7688 is limited to 1x1
This driver fully supports AP, station, mesh, ad-hoc and monitor mode.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
In addition to MT7603E PCI devices, the driver supports the WLAN core on
MT7628/MT7688, which needs to be defined in DT.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
MT7603 needs this to update the HT/VHT capabilities
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Remove following routine declarations that are no longer used
after commit cfca5f693c5d ("mt76usb: remove usb_mcu.c"):
- mt76u_mcu_complete_urb
- mt76u_deinit
- mt76u_buf_free
- mt76u_submit_urb
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
check nsgs value is less than urb->num_sgs in mt76u_process_rx_entry
in order to avoid an out-of-bound access of urb->sg array
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use skb_to_sgvec instad of skb_to_sgvec_nomark in mt76u_tx_build_sg.
Remove nsgs check in mt76u_tx_build_sg since it is already performed
by skb_to_sgvec
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Squash mt76u_buf_alloc_sg and mt76u_buf_alloc and remove duplicated
code. Reuse mt76u_refill_rx in mt76u_buf_alloc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add mt76u_fill_bulk_urb to initialize tx/rx urbs and
remove duplicate code
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix following static checker warning in mt76u_buf_free:
drivers/net/wireless/mediatek/mt76/usb.c:372 mt76u_buf_free()
warn: address of 'urb->sg[i]' is non-NULL
There is no need to check sg page pointer since urb->num_sgs
has been already validated in mt76u_fill_rx_sg
Fixes: cb83585e1121 ("mt76: usb: fix possible memory leak in mt76u_buf_free")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Don't need separate file just for kmalloc/kfree.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use usb_bulk_msg for reading MCU command responses. This simplify code
a lot.
Together with 97a3005759c ("mt76usb: allow mt76u_bulk_msg be used
for reads") it also fix possible problems with rx data buffers
not being aligned and contained within single page. After doing
page_frag_alloc(1024) consecutive page_frag_alloc(PAGE_SIZE) will
alloc PAGE_SIZE buffer at PAGE_SIZE - 1024 offset.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Extend mt76u_bulk_msg() such it can be used for synchronous bulk reads.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
