| Age | Commit message (Collapse) | Author |
|---|
|
* Raw NAND changes
A new controller driver, from Nuvoton, has been merged.
Bastien Curutchet has contributed a series improving the Davinci
controller driver, both on the organization of the code, but also on the
performance side. The binding has also been converted to yaml, received
a new OOB layout and now supports on-die ECC engines.
The Qualcomm controller driver has been deeply cleaned to extract some
parts of the code into a shared file with the Qualcomm SPI memory
controller.
Aside from these main changes, the Cadence binding has been converted to
yaml, the brcmnand controller driver has received a small fix, otherwise
some more minor changes have also made their way in.
* SPI NAND changes
The SPI NAND subsystem has seen a great improvement, with the advent of
DTR operations (DDR operations, which may be extended to the address
cycles). The first vendor driver to benefit from these improvements is
the Winbond driver.
A new manufacturer driver is added SkyHigh, with a new constraint for
the core, it is impossible to disable the on-die ECC engine.
A Foresee device is also now supported.
|
|
SPI NOR changes for 6.14
Notable changes:
- Add flash entries for Atmel AT25SF321, Spansion S28HL256T, S28HL02GT.
- Add support for vcc-supply regulators and their DT bindings.
- Drop mx25u25635f entry. The flash shares its ID with mx25u25645g and
both parts have an SFDP table. Removing their entry lets them be
driven by the generic SFDP-based driver.
|
|
The SPINAND_PAGE_READ_FROM_CACHE_OP macro has just been changed to stop
encoding the "fast" parameter (the macro has been duplicated and
renamed). The Skyhigh driver is new and is still using the old style
macro.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501161302.bQqBGjJ5-lkp@intel.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-kernel/20250116132010.4948547d@canb.auug.org.au/
Fixes: 042087247835d ("mtd: spinand: Create distinct fast and slow read from cache variants")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # build tested
|
|
W25N01JW and W25N02JW support many DTR read modes in single, dual and
quad configurations.
DTR modes however cannot be used at 166MHz, as the bus frequency in
this case must be lowered to 80MHz.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Make the link between the core macros and the datasheet.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
W25N01JW and W25N02JW use a different technology with higher frequencies
supported (up to 166MHz). There is one drawback though, the slowest
READ_FROM_CACHE command cannot run above 54MHz. Because of that, we need
to set a limit for these chips on the basic READ_FROM_CACHE variant.
Duplicating this list is not a problem because these chips have DTR
support, and the list of supported variants will diverge from all the
other chips when adding support for it.
Cc: stable+noautosel@kernel.org # New feature being added
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Advanced SPI-NAND chips are capable of reading data much faster by
leveraging DTR support. This support extends to dual and quad
configurations.
Create macros defining all possible read from cache DTR variants:
- SPINAND_PAGE_READ_FROM_CACHE_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_X2_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_X4_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_DUALIO_DTR_OP
- SPINAND_PAGE_READ_FROM_CACHE_QUADIO_DTR_OP
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently the best variant picked in the first one in the list provided
in the manufacturer driver. This worked well while all operations where
performed at the same speed, but with the introduction of DTR transfers
and per operation maximum frequencies, this no longer works correctly.
Let's continue iterating over all the alternatives, even if we find a
match, keeping a reference over the theoretically fastest
operation. Only at the end we can tell which variant is the best.
This logic happening only once at boot, the extra computing needed
compared to the previous version is acceptable wrt. the expected
improvements.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
While the SPINAND_PAGE_READ_FROM_CACHE_FAST_OP macro is supposed to be
able to run at the flash highest supported frequency, it is not the case
of the regular read from cache, which may be limited in terms of maximum
frequency. Add an optional argument to this macro, which will be used to
set the maximum frequency, if any.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
So far, the SPINAND_PAGE_READ_FROM_CACHE_OP macro was taking a first
argument, "fast", which was inducing the possibility to support higher
bus frequencies than with the normal (slower) read from cache
alternative. In practice, without frequency change on the bus, this was
likely without effect, besides perhaps allowing another variant of the
same command, that could run at the default highest speed. If we want to
support this fully, we need to add a frequency parameter to the slowest
command. But before we do that, let's drop the "fast" boolean from the
macro and duplicate it, this will further help supporting having
different frequencies allowed for each variant.
The change is also of course propagated to all users. It has the nice
effect to have all macros aligned on the same pattern.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based kernel configuration guards.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
spi: Support DTR in spi-mem
Changes to support DTR with spi-mem.
|
|
Add support for the OOB layout used by the ROM bootloader.
The same layout is used by both Keystone [1] and OMAPL138/DA850 [2]
which currently is the only users of davinci-nand.
Only select this layout if the `nand-is-boot-medium` property is set.
This to avoid breaking any existing devices out there.
[1] https://www.ti.com/lit/ug/spruhj3/spruhj3.pdf
[2] https://www.ti.com/lit/an/sprab41f/sprab41f.pdf
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
After commit e6204f39fe3a ("spi: amd: Drop redundant check"), clang warns (or
errors with CONFIG_WERROR=y):
drivers/spi/spi-amd.c:695:9: error: variable 'ret' is uninitialized when used here [-Werror,-Wuninitialized]
695 | return ret;
| ^~~
drivers/spi/spi-amd.c:673:9: note: initialize the variable 'ret' to silence this warning
673 | int ret;
| ^
| = 0
1 error generated.
ret is no longer set on anything other than the default switch path.
Replace ret with a direct return of 0 at the end of the function and
-EOPNOTSUPP in the default case to resolve the warning.
Fixes: e6204f39fe3a ("spi: amd: Drop redundant check")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501112315.ugYQ7Ce7-lkp@intel.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250111-spi-amd-fix-uninitialized-ret-v1-1-c66ab9f6a23d@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-mtd-v1-1-ee13140a4e9b@weissschuh.net
|
|
Infineon S28HL02GT is 3.0V, 2Gb Flash device with Octal interface.
It has the same functionalities with S28HS02GT.
Link: https://www.infineon.com/dgdl/Infineon-S28HS02GT_S28HS04GT_S28HL02GT_S28HL04GT_2Gb_4Gb_SEMPER_Flash_Octal_interface_1.8V_3.0V-DataSheet-v01_00-EN.pdf?fileId=8ac78c8c7e7124d1017f0631e33714d9
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[pratyush@kernel.org: add comment with flash name]
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/dc6aa706253a5200ff0c0d4523c2540312575c01.1734588106.git.Takahiro.Kuwano@infineon.com
|
|
Infineon S28HL256T is 3.0V, 256Mb Flash device with Octal interface.
It has the same functionalities with S28HS256T(1.8V).
Link: https://www.infineon.com/dgdl/Infineon-S28HS256T_S28HL256T_256Mb_SEMPER_Flash_Octal_interface_1_8V_3-DataSheet-v02_00-EN.pdf?fileId=8ac78c8c8fc2dd9c018fc66787aa0657
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[pratyush@kernel.org: add comment with flash name]
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/f052b04693f1100e725e076fd8a0ae339f8002c4.1734588106.git.Takahiro.Kuwano@infineon.com
|
|
We use the size as an indicator whether to parse SFDP or not. We don't
introduce a dedicated member for SFDP parsing because we'd like to keep
the struct size at a minimum, as it's used for every flash declaration.
Ideally we won't have flash entries at all, but there are still flash
parameters that aren't defined by SFDP, thus we need to statically
specify them.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20241219-spi-nor-flash-info-size-desc-v1-1-6b53cf011027@linaro.org
|
|
In the SPI-NAND layer, we currently make list of operation variants from
the fastest one to the slowest and there is a bit of logic in the core
to go over them and pick the first one that is supported by the
controller, ie. the fastest one among the supported ops.
This kind of logic only works if all operations run at the same
frequency, but as soon as we introduce per operation max frequencies it
is not longer as obvious which operation will be faster, especially
since it also depends on the PCB/controller frequency limitation.
One way to make this choice more clever is to go over all the
variants and for each of them derive an indicator which will help derive
the theoretical best. In this case, we derive a theoretical duration for
the entire operation and we take the smallest one.
Add a helper that parses the spi-mem operation and returns this value.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250110-winbond-6-11-rc1-quad-support-v3-20-7ab4bd56cf6e@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We do have macros for defining command, address, dummy and data
cycles. We also have a .dtr flag that implies sampling the bus on both
edges, but there are currently no macros enabling it. We might make use
of such macros, so let's create:
- SPI_MEM_DTR_OP_CMD
- SPI_MEM_DTR_OP_ADDR
- SPI_MEM_DTR_OP_DUMMY
- SPI_MEM_DTR_OP_DATA_OUT
- SPI_MEM_DTR_OP_DATA_OUT
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-19-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the order in which all the `struct spi_mem_op` members are
defined.
This is purely aesthetics, there is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-18-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-17-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-16-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-15-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-14-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Han Xu <han.xu@nxp.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Cc: Yogesh Gaur <yogeshgaur.83@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-13-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-12-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-11-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-10-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
This controller however performed a frequency check, which is also
observed during the ->check_op() phase.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Conor Dooley <conor.dooley@microchip.com>
Cc: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-9-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-8-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-7-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-6-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-5-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Both spi and spi-mem cores already take care of checking the minimum and
maximum speed for transfers depending on the controller
capabilities. There is no reason to repeat this check in controller
drivers.
Once this possible error condition removed from the function, it makes
no longer sense to return an int.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-4-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
This controller however performed a frequency check, which is also
observed during the ->check_op() phase.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-3-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are spi devices with multiple frequency limitations depending on
the invoked command. We probably do not want to afford running at the
lowest supported frequency all the time, so if we want to get the most
of our hardware, we need to allow per-operation frequency limitations.
Among all the SPI memory controllers, I believe all are capable of
changing the spi frequency on the fly. Some of the drivers do not make
any frequency setup though. And some others will derive a per chip
prescaler value which will be used forever.
Actually changing the frequency on the fly is something new in Linux, so
we need to carefully flag the drivers which do and do not support it. A
controller capability is created for that, and the presence for this
capability will always be checked before accepting such pattern.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-2-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the spi subsystem, the bus frequency is derived as follows:
- the controller may expose a minimum and maximum operating frequency
- the hardware description, through the spi peripheral properties,
advise what is the maximum acceptable frequency from a device/wiring
point of view.
Transfers must be observed at a frequency which fits both (so in
practice, the lowest maximum).
Actually, this second point mixes two information and already takes the
lowest frequency among:
- what the spi device is capable of (what is written in the component
datasheet)
- what the wiring allows (electromagnetic sensibility, crossovers,
terminations, antenna effect, etc).
This logic works until spi devices are no longer capable of sustaining
their highest frequency regardless of the operation. Spi memories are
typically subject to such variation. Some devices are capable of
spitting their internally stored data (essentially in read mode) at a
very fast rate, typically up to 166MHz on Winbond SPI-NAND chips, using
"fast" commands. However, some of the low-end operations, such as
regular page read-from-cache commands, are more limited and can only be
executed at 54MHz at most. This is currently a problem in the SPI-NAND
subsystem. Another situation, even if not yet supported, will be with
DTR commands, when the data is latched on both edges of the clock. The
same chips as mentioned previously are in this case limited to
80MHz. Yet another example might be continuous reads, which, under
certain circumstances, can also run at most at 104 or 120MHz.
As a matter of fact, the "one frequency per chip" policy is outdated and
more fine grain configuration is needed: we need to allow per-operation
frequency limitations. So far, all datasheets I encountered advertise a
maximum default frequency, which need to be lowered for certain specific
operations. So based on the current infrastructure, we can still expect
firmware (device trees in general) to continued advertising the same
maximum speed which is a mix between the PCB limitations and the chip
maximum capability, and expect per-operation lower frequencies when this
is relevant.
Add a `struct spi_mem_op` member to carry this information. Not
providing this field explicitly from upper layers means that there is no
further constraint and the default spi device maximum speed will be
carried instead. The SPI_MEM_OP() macro is also expanded with an
optional frequency argument, because virtually all operations can be
subject to such a limitation, and this will allow for a smooth and
discrete transition.
For controller drivers which do not implement the spi-mem interface, the
per-transfer speed is also set acordingly to a lower (than the maximum
default) speed when relevant.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-1-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For each NAND_OP_WAITRDY_INSTR operation, the NANDFSR register is
polled only once every 100 us to check for the EMA_WAIT pin. This
isn't frequent enough and causes delays in NAND accesses.
Set the polling interval to 5 us. It increases the page read speed
reported by flash_speed by ~30% (~10% on page writes).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Fix a buffer overflow issue in qcom_clear_bam_transaction by using
struct_group to group related fields and avoid FORTIFY_SOURCE warnings.
On x86 architecture, the following error occurs due to warnings being
treated as errors:
In function ‘fortify_memset_chk’,
inlined from ‘qcom_clear_bam_transaction’ at
drivers/mtd/nand/qpic_common.c:88:2:
./include/linux/fortify-string.h:480:25: error: call to ‘__write_overflow_field’
declared with attribute warning: detected write beyond size of field
(1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
480 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
LD [M] drivers/mtd/nand/nandcore.o
CC [M] drivers/w1/masters/mxc_w1.o
cc1: all warnings being treated as errors
This patch addresses the issue by grouping the related fields in
struct bam_transaction using struct_group and updating the memset call
accordingly.
Fixes: 8c52932da5e6 ("mtd: rawnand: qcom: cleanup qcom_nandc driver")
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix escaping of '$' in scripts/mksysmap
- Fix a modpost crash observed with the latest binutils
- Fix 'provides' in the linux-api-headers pacman package
* tag 'kbuild-fixes-v6.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: pacman-pkg: provide versioned linux-api-headers package
modpost: work around unaligned data access error
modpost: refactor do_vmbus_entry()
modpost: fix the missed iteration for the max bit in do_input()
scripts/mksysmap: Fix escape chars '$'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"25 hotfixes. 16 are cc:stable. 18 are MM and 7 are non-MM.
The usual bunch of singletons and two doubletons - please see the
relevant changelogs for details"
* tag 'mm-hotfixes-stable-2025-01-04-18-02' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (25 commits)
MAINTAINERS: change Arınç _NAL's name and email address
scripts/sorttable: fix orc_sort_cmp() to maintain symmetry and transitivity
mm/util: make memdup_user_nul() similar to memdup_user()
mm, madvise: fix potential workingset node list_lru leaks
mm/damon/core: fix ignored quota goals and filters of newly committed schemes
mm/damon/core: fix new damon_target objects leaks on damon_commit_targets()
mm/list_lru: fix false warning of negative counter
vmstat: disable vmstat_work on vmstat_cpu_down_prep()
mm: shmem: fix the update of 'shmem_falloc->nr_unswapped'
mm: shmem: fix incorrect index alignment for within_size policy
percpu: remove intermediate variable in PERCPU_PTR()
mm: zswap: fix race between [de]compression and CPU hotunplug
ocfs2: fix slab-use-after-free due to dangling pointer dqi_priv
fs/proc/task_mmu: fix pagemap flags with PMD THP entries on 32bit
kcov: mark in_softirq_really() as __always_inline
docs: mm: fix the incorrect 'FileHugeMapped' field
mailmap: modify the entry for Mathieu Othacehe
mm/kmemleak: fix sleeping function called from invalid context at print message
mm: hugetlb: independent PMD page table shared count
maple_tree: reload mas before the second call for mas_empty_area
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A randconfig build fix and a performance fix:
- Fix the CONFIG_RESET_CONTROLLER=n path signature of
clk_imx8mp_audiomix_reset_controller_register() to appease
randconfig
- Speed up the sdhci clk on TH1520 by a factor of 4 by adding
a fixed factor clk"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: clk-imx8mp-audiomix: fix function signature
clk: thead: Fix TH1520 emmc and shdci clock rate
|
|
The Arch Linux glibc package contains a versioned dependency on
"linux-api-headers". If the linux-api-headers package provided by
pacman-pkg does not specify an explicit version this dependency is not
satisfied.
Fix the dependency by providing an explicit version.
Fixes: c8578539deba ("kbuild: add script and target to generate pacman package")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fix from Wim Van Sebroeck:
- fix error message during stm32 driver probe
* tag 'linux-watchdog-6.13-rc6' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: stm32_iwdg: fix error message during driver probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fixes from Tejun Heo:
- Fix a bug where bpf_iter_scx_dsq_new() was not initializing the
iterator's flags and could inadvertently enable e.g. reverse
iteration
- Fix a bug where scx_ops_bypass() could call irq_restore twice
- Add Andrea and Changwoo as maintainers for better review coverage
- selftests and tools/sched_ext build and other fixes
* tag 'sched_ext-for-6.13-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Fix dsq_local_on selftest
sched_ext: initialize kit->cursor.flags
sched_ext: Fix invalid irq restore in scx_ops_bypass()
MAINTAINERS: add me as reviewer for sched_ext
MAINTAINERS: add self as reviewer for sched_ext
scx: Fix maximal BPF selftest prog
sched_ext: fix application of sizeof to pointer
selftests/sched_ext: fix build after renames in sched_ext API
sched_ext: Add __weak to fix the build errors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
- Suppress a corner case spurious flush dependency warning
- Two trivial changes
* tag 'wq-for-6.13-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: add printf attribute to __alloc_workqueue()
workqueue: Do not warn when cancelling WQ_MEM_RECLAIM work from !WQ_MEM_RECLAIM worker
rust: add safety comment in workqueue traits
|
|
Pull block fixes from Jens Axboe:
"Collection of fixes for block. Particularly the target name overflow
has been a bit annoying, as it results in overwriting random memory
and hence shows up as triggering various other bugs.
- NVMe pull request via Keith:
- Fix device specific quirk for PRP list alignment (Robert)
- Fix target name overflow (Leo)
- Fix target write granularity (Luis)
- Fix target sleeping in atomic context (Nilay)
- Remove unnecessary tcp queue teardown (Chunguang)
- Simple cdrom typo fix"
* tag 'block-6.13-20250103' of git://git.kernel.dk/linux:
cdrom: Fix typo, 'devicen' to 'device'
nvme-tcp: remove nvme_tcp_destroy_io_queues()
nvmet-loop: avoid using mutex in IO hotpath
nvmet: propagate npwg topology
nvmet: Don't overflow subsysnqn
nvme-pci: 512 byte aligned dma pool segment quirk
|
