| Age | Commit message (Collapse) | Author |
|---|
|
Merge MIPS patches destined to both 4.7 and kvm/next, to avoid
unnecessary conflicts.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When emulating TLB miss / invalid exceptions during CACHE instruction
emulation, be sure to set up the correct PC and host_cp0_badvaddr state
for the kvm_mips_emlulate_tlb*_ld() function to pick up for guest EPC
and BadVAddr.
PC needs to be rewound otherwise the guest EPC will end up pointing at
the next instruction after the faulting CACHE instruction.
host_cp0_badvaddr must be set because guest CACHE instructions trap with
a Coprocessor Unusable exception, which doesn't update the host BadVAddr
as a TLB exception would.
This doesn't tend to get hit when dynamic translation of emulated
instructions is enabled, since only the first execution of each CACHE
instruction actually goes through this code path, with subsequent
executions hitting the SYNCI instruction that it gets replaced with.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When a CACHE instruction is emulated by kvm_mips_emulate_cache(), the PC
is first updated to point to the next instruction, and afterwards it
falls through the "dont_update_pc" label, which rewinds the PC back to
its original address.
This works when dynamic translation of emulated instructions is enabled,
since the CACHE instruction is replaced with a SYNCI which works without
trapping, however when dynamic translation is disabled the guest hangs
on CACHE instructions as they always trap and are never stepped over.
Roughly swap the meanings of the "done" and "dont_update_pc" to match
kvm_mips_emulate_CP0(), so that "done" will roll back the PC on failure,
and "dont_update_pc" won't change PC at all (for the sake of exceptions
that have already modified the PC).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When faulting guest addresses are matched against guest segments with
the KVM_GUEST_KSEGX() macro, change the mask to 0xe0000000 so as to
include bit 31.
This is mainly for safety's sake, as it prevents a rogue BadVAddr in the
host kseg2/kseg3 segments (e.g. 0xC*******) after a TLB exception from
matching the guest kseg0 segment (e.g. 0x4*******), triggering an
internal KVM error instead of allowing the corresponding guest kseg0
page to be mapped into the host vmalloc space.
Such a rogue BadVAddr was observed to happen with the host MIPS kernel
running under QEMU with KVM built as a module, due to a not entirely
transparent optimisation in the QEMU TLB handling. This has already been
worked around properly in a previous commit.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Copy __kvm_mips_vcpu_run() into unmapped memory, so that we can never
get a TLB refill exception in it when KVM is built as a module.
This was observed to happen with the host MIPS kernel running under
QEMU, due to a not entirely transparent optimisation in the QEMU TLB
handling where TLB entries replaced with TLBWR are copied to a separate
part of the TLB array. Code in those pages continue to be executable,
but those mappings persist only until the next ASID switch, even if they
are marked global.
An ASID switch happens in __kvm_mips_vcpu_run() at exception level after
switching to the guest exception base. Subsequent TLB mapped kernel
instructions just prior to switching to the guest trigger a TLB refill
exception, which enters the guest exception handlers without updating
EPC. This appears as a guest triggered TLB refill on a host kernel
mapped (host KSeg2) address, which is not handled correctly as user
(guest) mode accesses to kernel (host) segments always generate address
error exceptions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Chris Wilson reported a divide by 0 at:
post_init_entity_util_avg():
> 725 if (cfs_rq->avg.util_avg != 0) {
> 726 sa->util_avg = cfs_rq->avg.util_avg * se->load.weight;
> -> 727 sa->util_avg /= (cfs_rq->avg.load_avg + 1);
> 728
> 729 if (sa->util_avg > cap)
> 730 sa->util_avg = cap;
> 731 } else {
Which given the lack of serialization, and the code generated from
update_cfs_rq_load_avg() is entirely possible:
if (atomic_long_read(&cfs_rq->removed_load_avg)) {
s64 r = atomic_long_xchg(&cfs_rq->removed_load_avg, 0);
sa->load_avg = max_t(long, sa->load_avg - r, 0);
sa->load_sum = max_t(s64, sa->load_sum - r * LOAD_AVG_MAX, 0);
removed_load = 1;
}
turns into:
ffffffff81087064: 49 8b 85 98 00 00 00 mov 0x98(%r13),%rax
ffffffff8108706b: 48 85 c0 test %rax,%rax
ffffffff8108706e: 74 40 je ffffffff810870b0
ffffffff81087070: 4c 89 f8 mov %r15,%rax
ffffffff81087073: 49 87 85 98 00 00 00 xchg %rax,0x98(%r13)
ffffffff8108707a: 49 29 45 70 sub %rax,0x70(%r13)
ffffffff8108707e: 4c 89 f9 mov %r15,%rcx
ffffffff81087081: bb 01 00 00 00 mov $0x1,%ebx
ffffffff81087086: 49 83 7d 70 00 cmpq $0x0,0x70(%r13)
ffffffff8108708b: 49 0f 49 4d 70 cmovns 0x70(%r13),%rcx
Which you'll note ends up with 'sa->load_avg - r' in memory at
ffffffff8108707a.
By calling post_init_entity_util_avg() under rq->lock we're sure to be
fully serialized against PELT updates and cannot observe intermediate
state like this.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yuyang Du <yuyang.du@intel.com>
Cc: bsegall@google.com
Cc: morten.rasmussen@arm.com
Cc: pjt@google.com
Cc: steve.muckle@linaro.org
Fixes: 2b8c41daba32 ("sched/fair: Initiate a new task's util avg to a bounded value")
Link: http://lkml.kernel.org/r/20160609130750.GQ30909@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The PWM device exposed by the HLCDC IP is configured with an inverted
polarity by default. Registering the PWM chip with the normal polarity
was not a problem before commit 42e8992c58d4 ("pwm: Add core
infrastructure to allow atomic updates") because the ->set_polarity()
hook was called no matter the current polarity state, but this is no longer
the case.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Directly accessing inode fields bypasses ->getattr()
and can cause problems when the underlying filesystem
does not have the default ->getattr() implementation.
So instead of obtaining the backing inode via d_backing_inode()
use vfs_getattr() and obtain what we need from the kstat struct.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This reverts commit 87f15d4add758fb7fc76655721af94be57a4c17d.
vfs_stat() can only be used on user supplied buffers.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This reverts commit 322ea0bbf3003df17b6253f76e572c37d79a6810.
vfs_stat() can only be used on user supplied buffers.
UBI's kapi.c is the API to the kernel and therefore vfs_stat()
is inappropriate.
This solves the problem that mounting any UBIFS will immediately
fail with -EINVAL.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Add the missing unlock before return from function i915_ppgtt_info()
in the error handling case.
Fixes: 1d2ac403ae3b(drm: Protect dev->filelist with its own mutex)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465861320-26221-1-git-send-email-weiyj_lk@163.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fixes from Tejun Heo:
"While adding GFP_ATOMIC support to the percpu allocator, the
synchronization for the fast-path which doesn't require external
allocations was separated into pcpu_lock.
Unfortunately, it incorrectly decoupled async paths and percpu
chunks could get destroyed while still being operated on. This
contains two patches to fix the bug"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix synchronization between synchronous map extension and chunk destruction
percpu: fix synchronization between chunk->map_extend_work and chunk destruction
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Some driver specific fixes for the regulator subsystem:
- Some of the changes to the core that were merged in the last merge
window exposed the fact that the qcom-smd driver hadn't implemented
the voltage enumeration interfaces like it should. Since it's a
simple driver specific fix to implement them do that.
- Fix the ramp delay configuration for tps51632"
* tag 'regulator-fix-v4.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom_smd: add list_voltage callback
regulator: qcom_smd: add regulator ops for pm8941 lnldo
regulator: qcom_smd: add list_voltage callback
regulator: tps51632: Fix setting ramp delay
|
|
https://github.com/foss-for-synopsys-dwc-arc-processors/linux into drm-next
Add support for arcgpu on the sim platform.
* 'topic-arcpgu-sim' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux:
ARC: [nsimosci] Enable ARC PGU on nSIM OSCI virtual platforms
ARCv2: [vdk] Enable ARC PGU on HS38 VDK
drm/arcpgu: Make ARC PGU usable on simulation platforms
|
|
With commit e58e87adc8bf9 "powerpc/mm: Update _PAGE_KERNEL_RO" we now
use all the three PPP bits. The top bit is now used to have a PPP value
of 0b110 which will be mapped to kernel read only. When updating the
hpte entry use right mask such that we update the 63rd bit (top 'P' bit)
too.
Prior to e58e87adc8bf we didn't support KERNEL_RO at all (it was ==
KERNEL_RW), so this isn't a regression as such.
Fixes: e58e87adc8bf ("powerpc/mm: Update _PAGE_KERNEL_RO")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Acquire a reference to the carrier's kernel module in bus code, so
it can't be removed from the kernel while it still has a bus and thus
possibly devices attached to it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Andreas Werner <andreas.werner@men.de>
Tested-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mcb_probe() does not aqcuire a reference to the probed device but drops one
when removing the device. As it is actually using the device, it should grab
a reference via get_device().
This could lead to a panic found with a rmmod/modprobe stress test
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Andreas Werner <andreas.werner@men.de>
Tested-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2ba272d7bde27e1db2cf1c6cee49b01b7ea08989.
The issue fixed by this patch is specific to compute rings and the
previous patch was enough. Additionally, this patch as been traced
to strange behavior on some CZ systems so we might as well drop it.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Fixes for Exynos-based Snow and Peach Pit boards for regressions introduced in
4.7-rc1 because OF graph logic expects specific names of child nodes.
* tag 'samsung-fixes-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board
ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
I would like to help reviewing FSL/NXP ARM architecture patches.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into fixes
SoCFPGA fix for v4.7
- Add missing PHY phandle for SoCFPGA VINING board
* tag 'socfpga_fix_for_v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: Add missing PHY phandle
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Wrong operator.
Reported-by: David Binderman <linuxdev.baldrick@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When executing in a PCI passthrough based virtuzliation environment, the
hypervisor will usually attempt to send a PCIe bus reset signal to the
ASIC when the VM reboots. In this scenario, the card is not correctly
initialized, but we still consider it to be posted. Therefore, in a
passthrough based environemnt we should always post the card to guarantee
it is in a good state for driver initialization.
Ported from amdgpu commit:
amdgpu: fix asic initialization for virtualized environments
Cc: Andres Rodriguez <andres.rodriguez@amd.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When executing in a PCI passthrough based virtuzliation environemnt, the
hypervisor will usually attempt to send a PCIe bus reset signal to the
ASIC when the VM reboots. In this scenario, the card is not correctly
initialized, but we still consider it to be posted. Therefore, in a
passthrough based environemnt we should always post the card to guarantee
it is in a good state for driver initialization.
However, if we are operating in SR-IOV mode it is up to the GIM driver
to manage the asic state, therefore we should not post the card (and
shouldn't be able to do it either).
v2: add missing semi-colon
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Andres Rodriguez <andres.rodriguez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Replace the legacy drm_vblank_{on,off}() with the new helper functions.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-7-git-send-email-gustavo@padovan.org
|
|
We don't need to use &radeon_crtc->base there as crtc is available
in the function.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-10-git-send-email-gustavo@padovan.org
|
|
We don't need to use &amdgpu_crtc->base there as crtc is available
in the function.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-9-git-send-email-gustavo@padovan.org
|
|
Replace the legacy drm_vblank_{on,off}() with the new helper functions.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-8-git-send-email-gustavo@padovan.org
|
|
Replace the legacy drm_vblank_{on,off}() with the new helper functions.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-6-git-send-email-gustavo@padovan.org
|
|
As they are not used anywhere outside drm_irq.c make them static.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-4-git-send-email-gustavo@padovan.org
|
|
We don't have any user of this function anymore, let's remove it.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-3-git-send-email-gustavo@padovan.org
|
|
We don't have any user of this function anymore, let's remove it.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-2-git-send-email-gustavo@padovan.org
|
|
Replace the legacy drm_send_vblank_event(), drm_arm_vblank_event() and
drm_vblank_{get,put}() with the new helper functions.
v2: add crtc to nouveau_page_flip_state (comment from Mario Kleiner)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465308482-15104-1-git-send-email-gustavo@padovan.org
|
|
Seems to cause problems for some older hardware. Kudos to Thom Kouwenhoven
for working a lot with the PLLs and figuring this out.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Seems r600/r700 does not like hard reset while freezing for hibernation
(regression due to 274ad65c9d02bdcbee9bae045517864c3521d530 which itself
is a fix for hibernation on some GPU families). Until i can debug further
issue with r600, let just disable this for r600/r700 as they are very
similar family and bug affecting one likely affect the other.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'regulator/fix/tps51632' into regulator-linus
|
|
There are four non-static functions in i915_guc_submission.c that take a
'dev' parameter. All are called only from GuC loader code, and can be
easily converted to accept 'dev_priv' instead.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465579766-31595-1-git-send-email-david.s.gordon@intel.com
|
|
Convert all static functions in i915_guc_submission.c that currently
take a 'dev' pointer to take 'dev_priv' instead (there are three,
guc_client_alloc(), guc_client_free(), and gem_allocate_guc_obj().
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
We can check the power state of the PHY data and common lanes as
reported by the PHY. Do this in case we need to debug problems where the
PHY gets stuck in an unexpected state.
Note that I only check these when the lanes are expected to be powered
on purpose, since it's not clear at what point the PHY power/clock gates
things.
v2:
- Don't report the encoder as disabled when the sanity check fails.
(Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465825477-32671-1-git-send-email-imre.deak@intel.com
|
|
Rename these remaining function prefixes to better align with the
corresponding SKL functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
So far we configured a static lane latency optimization during driver
loading/resuming. The specification changed at one point and now this
configuration depends on the lane count, so move the configuration
to modeset time accordingly.
It's not clear when this lane configuration takes effect. The
specification only requires that the programming is done before enabling
the port. On CHV OTOH the lanes start to power up already right after
enabling the PLL. To be safe preserve the current order and set things
up already before enabling the PLL.
v2: (Ander)
- Simplify the optimization mask calculation.
- Use the correct pipe_config always during the calculation instead
of the bogus intel_crtc->config.
CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95476
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
So far we depended on the HW to dynamically power down unused PHYs and
so we enabled them manually once during driver loading/resuming. There
are indications however that we can achieve better power savings by
manual powering toggling. So make the PHY enabling/disabling to happen
on-demand whenever we need either the corresponding AUX or port
functionality. CHV does this already by enabling the PHY along the
corresponding PHY common lane power wells there, do the same on BXT by
adding virtual power wells for the same purpose.
Also sanity check the common lane power down ack signal from the PHY. Do
this only when the PHY is enabled, since it's not clear at what point
the HW power/clock gates things.
While at it rename broxton_ prefix to bxt_ in related function names to
better align with the SKL code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
These helpers will be needed by the next patch, so factor them out.
No functional change.
v2:
- Move the refcount==0 WARN to the new put helper. (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
A follow-up patch moves the PHY enabling to the power well code where
enabling/disabling the PHYs will happen independently. Because of this
waiting for the GRC calibration in PHY1 asynchronously would need some
additional logic. Instead of adding that let's keep things simple for now
and wait synchronously. My measurements showed that the calibration
takes ~4ms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
|
|
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in nSIM OSCI virtual platforms
with modern Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in HS38 VDK with modern
Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
In case of simulation there's no real encoder/transmitter device
because in the model's virtual LCD we're rendering whatever
appears in frame-buffer memory.
Signed-off-by: Ruud Derwig <rderwig@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
There were a couple messed up things about this fail path.
(1) it would drop object_name_lock twice
(2) drm_gem_handle_delete() (in drm_gem_remove_prime_handles())
needs to grab prime_lock
Reported-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465500559-17873-1-git-send-email-robdclark@gmail.com
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1465821536-21312-1-git-send-email-kraxel@redhat.com
|
|
It seems pretty clear that bitwise OR was intended here and not logical
OR.
Fixes: 6fc29133eafb ('drm/i915/gen9: Add WaDisableSkipCaching')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
|
