| Age | Commit message (Collapse) | Author |
|---|
|
IPv6 packet may carry more than one extension header, and IPv6 nodes must
accept and attempt to process extension headers in any order and occurring
any number of times in the same packet. Hence, there should be no
assumption that Segment Routing extension header is to appear immediately
after the IPv6 header.
Moreover, section 4.1 of RFC 8200 gives a recommendation on the order of
appearance of those extension headers within an IPv6 packet. According to
this recommendation, Segment Routing extension header should appear after
Hop-by-Hop and Destination Options headers (if they present).
This patch fixes the get_srh(), so it gets the segment routing header
regardless of its position in the chain of the extension headers in IPv6
packet, and makes sure that the IPv6 routing extension header is of Type 4.
Signed-off-by: Ahmed Abdelsalam <amsalam20@gmail.com>
Acked-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported by Johannes Berg [1]. Problem here: function
process_proto_type() concatenates the striped lines of declaration
without any whitespace. A one-liner of::
struct something {
struct foo
bar;
};
has to be::
struct something {struct foo bar;};
Without the patching process_proto_type(), the result missed the space
between 'foo' and 'bar'::
struct something {struct foobar;};
Bugfix of process_proto_type() brings next error when blank lines
between enum declaration::
warning: Enum value ' ' not described in enum 'foo'
Problem here: dump_enum() does not strip leading whitespaces from
the concatenated string (with the new additional space from
process_proto_type).
[1] https://www.mail-archive.com/linux-doc@vger.kernel.org/msg12410.html
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Antoine Tenart says:
====================
net: mvpp2: comphy configuration
This series, following up the one one the GoP/MAC configuration, aims at
stopping to depend on the firmware/bootloader configuration when using
the PPv2 engine. With this series the PPv2 driver does not need to rely
on a previous configuration, and dynamic reconfiguration while the
kernel is running can be done (i.e. switch one port from SGMII to 10G,
or the opposite). A port can now be configured in a different mode than
what's done in the firmware/bootloader as well.
The series first contain patches in the generic PHY framework to support
what is called the comphy (common PHYs), which is an h/w block providing
PHYs that can be configured in various modes ranging from SGMII, 10G
to SATA and others. As of now only the SGMII and 10G modes are
supported by the comphy driver.
Then patches are modifying the PPv2 driver to first add the comphy
initialization sequence (i.e. calls to the generic PHY framework) and to
then take advantage of this to allow dynamic reconfiguration (i.e.
configuring the mode of a port given what's connected, between sgmii and
10G). Note the use of the comphy in the PPv2 driver is kept optional
(i.e. if not described in dt the driver still as before an relies on the
firmware/bootloader configuration).
Finally there are dt/defconfig patches to describe and take advantage of
this.
This was tested on a range of devices: 8040-db, 8040-mcbin and 7040-db.
@Dave: the dt patches should go through the mvebu tree (patches 9-13).
Thanks!
Antoine
Since v3:
- Now use of_phy_simple_xlate() to retrieve the phy.
- Added an owner in the phy_ops structure.
- Now allow the module to be selected with COMPILE_TEST.
- Removed unused parameter in the comphy set_mode functions.
- Added Kishon Acked-by in patch 1.
Since v2:
- Kept the link mode enforcement.
- Removed the netif_running() check.
- Reworded the "dynamic reconfiguration of the PHY mode" commit log.
- Added one patch not to force the GMAC autoneg parameters when using
the XLG MAC.
Since v1:
- Updated the mode settings variable name in the comphy driver to
have 'cp110' in it.
- Documented the PHY cell argument in the dt documentation.
- New patch adding comphy phandles for the 7040-db board.
- Checked if the carrier_on/off functions were needed. They are.
- s/PHY/generic PHY/ in commit log of patch 1.
- Rebased on the latest net-next/master.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds logic to reconfigure the comphy/GoP/MAC when the link
state is updated at runtime. This is very useful on boards where many
link speed are supported: depending on what is negotiated the PPv2
driver will automatically reconfigures the link between the PHY and the
MAC.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the XLG MAC, it does not make sense to force the GMAC autoneg
parameters. This patch adds checks to only set the GMAC autoneg
parameters when needed (i.e. when not using the XLG MAC).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the link status changes, the phylib calls the link_event function
in the mvpp2 driver. Before this patch only the egress/ingress transmit
was enabled/disabled. This patch adds more functionality to the link
status management code by enabling/disabling the port per-cpu
interrupts, and the port itself. The queues are now stopped as well, and
the netif carrier helpers are called.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The link_event function is somewhat complicated. This cosmetic patch
simplifies it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some platforms, the comphy is between the MAC GoP and the PHYs. The
mvpp2 driver currently relies on the firmware/bootloader to configure
the comphy. As a comphy driver was added to the generic PHY framework,
this patch uses it in the mvpp2 driver to configure the comphy at boot
time to avoid relying on the bootloader.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell Armada 7K/8K SoCs contains an hardware block called COMPHY
that provides a number of shared PHYs used by various interfaces in the
SoC: network, SATA, PCIe, etc. This Device Tree binding allows to
describe this COMPHY hardware block.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the CP110 unit, which can be found on various Marvell platforms such
as the 7k and 8k (currently), a comphy (common PHYs) hardware block can
be found. This block provides a number of PHYs which can be used in
various modes by other controllers (network, SATA ...). These common
PHYs must be configured for the controllers using them to work correctly
either at boot time, or when the system runs to switch the mode used.
This patch adds a driver for this comphy hardware block, providing
callbacks for the its PHYs so that consumers can configure the modes
used.
As of this commit, two modes are supported by the comphy driver: sgmii
and 10gkr.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds more generic PHY modes to the phy_mode enum, to
allow configuring generic PHYs to the SGMII and/or the 10GKR mode
by using the set_mode callback.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Two fixes (a vmwgfx and core drm fix) in the queue for 4.13 final,
hopefully that is it"
* tag 'drm-fixes-for-v4.13-rc8' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix F26 Wayland screen update issue
drm/bridge/sii8620: Fix memory corruption
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes: a NULL deref in qedf, an off by one in sg and a fix
to IPR to prevent an error on initialisation"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedf: Fix a potential NULL pointer dereference
scsi: sg: off by one in sg_ioctl()
scsi: ipr: Set no_report_opcodes for RAID arrays
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML fix from Richard Weinberger:
"This contains a single fix for a regression which was introduced while
the merge window"
* 'for-linus-4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Fix check for _xstate for older hosts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha update from Matt Turner:
"A few fixes and wires up some additional syscalls."
[ Some of this is technically not really rc7 material, but it's alpha,
and it all looks safe anyway. Matt explains: "My alpha has been
offline, hence the very late-in-cycle pull request" and hasn't caused
problems before, so he gets to slide. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: uapi: Add support for __SANE_USERSPACE_TYPES__
alpha: Define ioremap_wc
alpha: Fix section mismatches
alpha: support R_ALPHA_REFLONG relocations for module loading
alpha: Fix typo in ev6-copy_user.S
alpha: Package string routines together
alpha: Update for new syscalls
alpha: Fix build error without CONFIG_VGA_HOSE.
|
|
We should not hold a spinlock while pushing the skb into the networking
stack, so move the call to netif_rx_ni out of the critical region to where
we have dropped the spinlock.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chris Mi says:
====================
net/sched: Improve getting objects by indexes
Using current TC code, it is very slow to insert a lot of rules.
In order to improve the rules update rate in TC,
we introduced the following two changes:
1) changed cls_flower to use IDR to manage the filters.
2) changed all act_xxx modules to use IDR instead of
a small hash table
But IDR has a limitation that it uses int. TC handle uses u32.
To make sure there is no regression, we add several new IDR APIs
to support unsigned long.
v2
==
Addressed Hannes's comment:
express idr_alloc in terms of idr_alloc_ext and most of the other functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Typically, each TC filter has its own action. All the actions of the
same type are saved in its hash table. But the hash buckets are too
small that it degrades to a list. And the performance is greatly
affected. For example, it takes about 0m11.914s to insert 64K rules.
If we convert the hash table to IDR, it only takes about 0m1.500s.
The improvement is huge.
But please note that the test result is based on previous patch that
cls_flower uses IDR.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, all filters with the same priority are linked in a doubly
linked list. Every filter should have a unique handle. To make the
handle unique, we need to iterate the list every time to see if the
handle exists or not when inserting a new filter. It is time-consuming.
For example, it takes about 5m3.169s to insert 64K rules.
This patch changes cls_flower to use IDR. With this patch, it
takes about 0m1.127s to insert 64K rules. The improvement is huge.
But please note that in this testing, all filters share the same action.
If every filter has a unique action, that is another bottleneck.
Follow-up patch in this patchset addresses that.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following new APIs are added:
int idr_alloc_ext(struct idr *idr, void *ptr, unsigned long *index,
unsigned long start, unsigned long end, gfp_t gfp);
void *idr_remove_ext(struct idr *idr, unsigned long id);
void *idr_find_ext(const struct idr *idr, unsigned long id);
void *idr_replace_ext(struct idr *idr, void *ptr, unsigned long id);
void *idr_get_next_ext(struct idr *idr, unsigned long *nextid);
Signed-off-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sphinx will now generate the table of contents automatically, which
avoids having the ToC getting out of sync with the rest of the document.
Signed-off-by: Josh Holland <anowlcalledjosh@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Drop all references to git daily snapshots of Linux mainline git tree
since they are no longer generated.
Drop the "Last update" info since 'git log' is a better source of that
info and since the Last update date is not being updated.
Yes, I read that this file is obsolete, but it still has some useful
information in it.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Signed-off-by: John de la Garza <john@jjdev.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Recent patch had an endian warning ie
cifs: return ENAMETOOLONG for overlong names in cifs_open()/cifs_lookup()
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
Currently the maximum size of SMB2/3 header is set incorrectly which
leads to hanging of directory listing operations on encrypted SMB3
connections. Fix this by setting the maximum size to 170 bytes that
is calculated as RFC1002 length field size (4) + transform header
size (52) + SMB2 header size (64) + create response size (56).
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
|
|
The legacy ioctl interfaces are only useful for BR/EDR operation and
since Linux 3.4 no longer needed anyway. This options allows disabling
them alltogether and use only management interfaces for setup and
control.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Subash Abhinov Kasiviswanathan says:
====================
net: Add support for rmnet driver
This patch series adds support for the rmnet driver which is required to
support recent chipsets using Qualcomm Technologies, Inc. modems. The data
from hardware follows the multiplexing and aggregation protocol (MAP).
This driver can be used to register onto any physical network device in
IP mode. Physical transports include USB, HSIC, PCIe and IP accelerator.
rmnet driver helps to decode these packets and queue them to network
stack (and encode and transmit it to the physical device).
v1: Same as the RFC patch with some minor fixes for issues reported by
kbuild test robot.
v1->v2: Change datatypes and remove config IOCTL as mentioned by David.
Also fix checkpatch issues and remove some unused code.
v2->v3: Move location to drivers/net and rename to rmnet. Change the
userspace - netlink communication from custom netlink to rtnl_link_ops.
Refactor some code. Use a fixed config for ingress and egress.
v3->v4: Move location to drivers/net/ethernet/qualcomm/.
Fix comments from Stephen and Jiri -
Split the ether and arp type changes into seperate patches.
Remove debug and custom logging and switch to standard netdevice log.
Remove module parameters. Refactor and change some code style issues.
v4->v5: Rename some structs and variables. Move the initializer
before the for loop start. Put the arp type in correct sequence.
v5->v6: Fix comments from Dan -
Use the upper link API. As a result, remove all the refcounting logic.
Device refcount is explicitly held on real_dev on rx_handler
registration only. Modifiy the flow control struct. Remove the unused
ethernet mode handling.
v6->v7: Fix comments from David - Add newline to end of Makefile. Remove
inline from .c files. Move the module init/exit to rmnet config. Fix an
error reported by kbuild test robot for an unused file.
v7->v8: Use a smaller value for ETH_P_MAP as mentioned by David. Change
netdev_info to netdev_dbg as mentioned by Andew. Fix comments from
Stephen regarding netdev_priv and sparse related errors of using 0 as NULL
v8->v9: Fix comments from David - Remove the CFLAG rule. Change the way
rmnet devices are freed. Instead of using a workqueue to unregister devices
individually, go through the list and free all devices within the rtnl_lock().
v9->v10: Actually fix the locking as mentioned by David. The locking scheme is
mentioned in a comment in rmnet_config.c. Change comment near MAP type
definition as mentioned by Dan. Refactor some code.
v10->v11: Allow RMNET to compile as a module as mentioned by David
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device. This will be used to provide all MAP functionality
on future hardware in a single consistent location.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define the raw IP type. This is needed for raw IP net devices
like rmnet.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define the Qualcomm multiplexing and aggregation (MAP) ether type 0x00F9.
This is needed for receiving data in the MAP protocol like RMNET. This is
not an officially registered ID.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch if you truncated a file to a smaller size it
wasn't freeing all the blocks properly. There are two reasons.
First, the metapath comparison was not comparing previous heights.
I added a function, mp_eq_to_hgt, which checks the metapath at
all heights prior to the target height.
Second, in function find_nonnull_ptr, it needed to zero out all
pointers for heights following the target height. Translated into
decimal integer terms, this way a number like 299, when incremented,
becomes 300, not 399. The 2 gets incremented to 3, and the following
digits need to be reset.
These two things allow the truncate state machine to properly find
the blocks it needs to delete.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
|
|
cq_period_mode assignment was mistakenly removed so it was always set to "0",
which is EQE based moderation, regardless of the device CAPs and
requested value in ethtool.
Fixes: 6a9764efb255 ("net/mlx5e: Isolate open_channels from priv->params")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix inline header size, make sure it is not greater than skb len.
This bug effects small packets, for example L2 packets with size < 18.
Fixes: ae76715d153e ("net/mlx5e: Check the minimum inline header mode before xmit")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When changing from switchdev to legacy mode, all the representor port
devices (uplink nic and reps) are cleaned up. Part of this cleaning
process is removing the neigh entries and the hash table containing them.
However, a representor neigh entry might be linked to the uplink port
hash table and if the uplink nic is cleaned first the cleaning of the
representor will end up in null deref.
Fix that by unloading the representors in the opposite order of load.
Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently if vxlan tunnel ipv6 src isn't supplied the driver fails to
resolve it as part of the route lookup. The resulting encap header
is left with a zeroed out ipv6 src address so the packets are sent
with this src ip.
Use an appropriate route lookup API that also resolves the source
ipv6 address if it's not supplied.
Fixes: ce99f6b97fcd ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, increasing the number of combined channels is changing
the RSS spread to use the new created channels.
Prevent the RSS spread change in case the user explicitly declare it,
to avoid overriding user configuration.
Tested:
when RSS default:
# ethtool -L ens8 combined 4
RSS spread will change and point to 4 channels.
# ethtool -X ens8 equal 4
# ethtool -L ens8 combined 6
RSS will not change after increasing the number of the channels.
Fixes: 8bf368620486 ('ethtool: ensure channel counts are within bounds during SCHANNELS')
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Function mlx5e_dealloc_rx_wqe is using page pointer value as an
indication to valid DMA mapping. In case that the mapping failed, we
released the page but kept the dangling pointer. Store the page pointer
only after the DMA mapping passed to avoid invalid page DMA unmap.
Fixes: bc77b240b3c5 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MLX5_INTERFACE_STATE_SHUTDOWN is not used in the code.
Fixes: 5fc7197d3a25 ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Fixes: 5fc7197d3a25 ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Support for ISSI version 0 was recently broken as the arm_srq_cmd
command, which is used only for ISSI version 0, was given the opcode
for ISSI version 1 instead of ISSI version 0.
Change arm_srq_cmd to use the correct command opcode for ISSI version
0.
Fixes: af1ba291c5e4 ('{net, IB}/mlx5: Refactor internal SRQ API')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Current code doesn't report DCB_CAP_DCBX_HOST capability when query
through getcap. User space lldptool expects capability to have HOST mode
set when it wants to configure DCBX CEE mode. In absence of HOST mode
capability, lldptool fails to switch to CEE mode.
This fix returns DCB_CAP_DCBX_HOST capability when port's DCBX
controlled mode is under software control.
Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
qos capability is the master capability bit that determines
if the DCBX is supported for the PCI function. If this bit is off,
driver cannot run any dcbx code.
Fixes: e207b7e99176 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Florian Westphal says:
====================
tcp: re-add header prediction
Eric reported a performance regression caused by header prediction
removal.
We now call tcp_ack() much more frequently, for some workloads
this brings in enough cache line misses to become noticeable.
We could possibly still kill HP provided we find a different
way to suppress unneeded tcp_ack, but given we're late in
the cycle it seems preferable to revert.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 45f119bf936b1f9f546a0b139c5b56f9bb2bdc78.
Eric Dumazet says:
We found at Google a significant regression caused by
45f119bf936b1f9f546a0b139c5b56f9bb2bdc78 tcp: remove header prediction
In typical RPC (TCP_RR), when a TCP socket receives data, we now call
tcp_ack() while we used to not call it.
This touches enough cache lines to cause a slowdown.
so problem does not seem to be HP removal itself but the tcp_ack()
call. Therefore, it might be possible to remove HP after all, provided
one finds a way to elide tcp_ack for most cases.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change was a followup to the header prediction removal,
so first revert this as a prerequisite to back out hp removal.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
snd_soc_of_parse_card_name() doesn't return an error if the requested
property isn't present, but silently fails to fill the card name. This can
not be changed, as it is a backwards compatibility measure itself.
We can not rely on the return value of this function alone, but must check
if the card name has been filled sucessfully when deciding to skip the
fallback path, which is in place for existing users.
Fixes: dedfaa1eedc7 (ASoC: simple-card-utils: enable "label" on
asoc_simple_card_parse_card_name)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document STM32 VREFBUF (voltage reference buffer) which can be used as
voltage reference for ADCs, DACs and external components.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When moving the IRDA code out of net/ into drivers/staging/irda/net, the
link order changes when IRDA is built into the kernel. That causes a
kernel crash at boot time as netfilter isn't initialized yet.
To fix this, move the init call level of the irda core to be
device_initcall() as the link order keeps this being initialized at the
correct time.
Reported-by: kernel test robot <fengguang.wu@intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is quite common for ti_cm_get_macid() to fail on some of the
platforms it is invoked on. They include any platform where
mac address is not part of SoC register space.
On these platforms, mac address is read and populated in
device-tree by bootloader. An example is TI DA850.
Downgrade the severity of message to "information", so it does
not spam logs when 'quiet' boot is desired.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
