| Age | Commit message (Collapse) | Author |
|---|
|
Add iommus properties to the device tree nodes for the two display
controllers found on Tegra114. This will allow the display controllers
to map physically non-contiguous buffers to I/O virtual contiguous
address spaces so that they can be used for scan-out.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add iommus properties to the device tree nodes for the two display
controllers found on Tegra30. This will allow the display controllers to
map physically non-contiguous buffers to I/O virtual contiguous address
spaces so that they can be used for scan-out.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the memory controller and wire up the interrupt that is used to
report errors. Provide a reference to the memory controller clock and
mark the device as being an IOMMU by adding an #iommu-cells property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the device tree node for the memory controller found on Tegra114
SoCs. The memory controller integrates an IOMMU (called SMMU) as well as
various knobs to tweak memory accesses by the various clients.
The old IOMMU device tree node is collapsed into the memory controller
node to more accurately describe the hardware. While this change is
incompatible, the IOMMU driver has never had any users so the change is
not going to cause any breakage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Collapses the old memory-controller and IOMMU device tree nodes into a
single node to more accurately describe the hardware.
While this is an incompatible change there are no users of the IOMMU on
Tegra, even though a driver has existed for some time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch adds the APB_MISC_GP_MIPI_PAD_CTRL_0 as a pin-control bank on
Tegra124 so the new MIPI pad control group can be muxed between CSI and
DSI_B.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
|
|
rescuer_thread() caches &rescuer->scheduled in a local variable
scheduled for convenience. There's one WARN_ON_ONCE() which was using
&rescuer->scheduled directly. Replace it with the local variable.
This patch causes no functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The memory controller on NVIDIA Tegra exposes various knobs that can be
used to tune the behaviour of the clients attached to it.
Currently this driver sets up the latency allowance registers to the HW
defaults. Eventually an API should be exported by this driver (via a
custom API or a generic subsystem) to allow clients to register latency
requirements.
This driver also registers an IOMMU (SMMU) that's implemented by the
memory controller. It is supported on Tegra30, Tegra114 and Tegra124
currently. Tegra20 has a GART instead.
The Tegra SMMU operates on memory clients and SWGROUPs. A memory client
is a unidirectional, special-purpose DMA master. A SWGROUP represents a
set of memory clients that form a logical functional unit corresponding
to a single device. Typically a device has two clients: one client for
read transactions and one client for write transactions, but there are
also devices that have only read clients, but many of them (such as the
display controllers).
Because there is no 1:1 relationship between memory clients and devices
the driver keeps a table of memory clients and the SWGROUPs that they
belong to per SoC. Note that this is an exception and due to the fact
that the SMMU is tightly integrated with the rest of the Tegra SoC. The
use of these tables is discouraged in drivers for generic IOMMU devices
such as the ARM SMMU because the same IOMMU could be used in any number
of SoCs and keeping such tables for each SoC would not scale.
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Fixes following build warnings:
gsc-core.c:350:17: warning: 'low_plane' may be used uninitialized
gsc-core.c:371:31: warning: 'high_plane' may be used uninitialized
Reported-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Recent rtl28xxu patch I made moved demod ADC enable from power control
to frontend control (due to slave demod support). Because of that we
need call USB interface frontend control too in order to enable ADC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The function releases the queue if the file being released is the queue
owner. The check reads the queue->owner field without taking the queue
lock, creating a race condition with functions that set the queue owner,
such as vb2_ioctl_reqbufs() for instance.
Fix this by moving the queue->owner check within the mutex protected
section.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The vb2_fop_poll() implementation tries to be clever on whether it needs
to lock the queue mutex by checking whether polling might start fileio.
The test requires reading the q->num_buffer field, which is racy if we
don't hold the queue mutex in the first place.
Remove the extra cleverness and just lock the mutex.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add support for selection target V4L2_SEL_TGT_NATIVE_SIZE. It is equivalent
of what V4L2_SEL_TGT_CROP_BOUNDS used to be. Support for
V4L2_SEL_TGT_CROP_BOUNDS is still supported by the driver as a compatibility
interface.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The fields were previously uninitialised, leaving the returned values to
where the user had set them. This was never the intention.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add input and output capability flags for setting native size of the device,
and document them.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The V4L2_SEL_TGT_NATIVE_SIZE target is used to denote e.g. the size of a
sensor's pixel array.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The sub-device format documentation documented scaling configuration through
formats. Instead the compose selection rectangle is elsewhere documented to
be used for the purpose. Remove scaling related part of the documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
We currently track the pid of the task that runs the VCPU in vcpu_load.
If a yield to that VCPU is triggered while the PID of the wrong thread
is active, the wrong thread might receive a yield, but this will most
likely not help the executing thread at all. Instead, if we only track
the pid on the KVM_RUN ioctl, there are two possibilities:
1) the thread that did a non-KVM_RUN ioctl is holding a mutex that
the VCPU thread is waiting for. In this case, the VCPU thread is not
runnable, but we also do not do a wrong yield.
2) the thread that did a non-KVM_RUN ioctl is sleeping, or doing
something that does not block the VCPU thread. In this case, the
VCPU thread can receive the directed yield correctly.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Rik van Riel <riel@redhat.com>
CC: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
CC: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm_enter_guest() has to be called with preemption disabled and will
set PF_VCPU. Current code takes PF_VCPU as a hint that the VCPU thread
is running and therefore needs no yield.
However, the check on PF_VCPU is wrong on s390, where preemption has
to stay enabled in order to correctly process page faults. Thus,
s390 reenables preemption and starts to execute the guest. The thread
might be scheduled out between kvm_enter_guest() and kvm_exit_guest(),
resulting in PF_VCPU being set but not being run. When this happens,
the opportunity for directed yield is missed.
However, this check is done already in kvm_vcpu_on_spin before calling
kvm_vcpu_yield_loop:
if (!ACCESS_ONCE(vcpu->preempted))
continue;
so the check on PF_VCPU is superfluous in general, and this patch
removes it.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Current linear search doesn't scale well when
large amount of memslots is used and looked up slot
is not in the beginning memslots array.
Taking in account that memslots don't overlap, it's
possible to switch sorting order of memslots array from
'npages' to 'base_gfn' and use binary search for
memslot lookup by GFN.
As result of switching to binary search lookup times
are reduced with large amount of memslots.
Following is a table of search_memslot() cycles
during WS2008R2 guest boot.
boot, boot + ~10 min
mostly same of using it,
slot lookup randomized lookup
max average average
cycles cycles cycles
13 slots : 1450 28 30
13 slots : 1400 30 40
binary search
117 slots : 13000 30 460
117 slots : 2000 35 180
binary search
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
it will allow to use binary search for GFN -> memslot
lookups, reducing lookup cost with large slots amount.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In typical guest boot workload only 2-3 memslots are used
extensively, and at that it's mostly the same memslot
lookup operation.
Adding LRU cache improves average lookup time from
46 to 28 cycles (~40%) for this workload.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
UP/DOWN shift loops will shift array in needed
direction and stop at place where new slot should
be placed regardless of old slot size.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
if number of pages haven't changed sorting algorithm
will do nothing, so there is no need to do extra check
to avoid entering sorting logic.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
While fixing an x2apic bug,
17d68b7 KVM: x86: fix guest-initiated crash with x2apic (CVE-2013-6376)
we've made only one cluster available. This means that the amount of
logically addressible x2APICs was reduced to 16 and VCPUs kept
overwriting themselves in that region, so even the first cluster wasn't
set up correctly.
This patch extends x2APIC support back to the logical_map's limit, and
keeps the CVE fixed as messages for non-present APICs are dropped.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
They can't be violated now, but play it safe for the future.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
x2apic allows destinations > 0xff and we don't want them delivered to
lower APICs. They are correctly handled by doing nothing.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Physical mode can't address more than one APIC, but lowest-prio is
allowed, so we just reuse our paths.
SDM 10.6.2.1 Physical Destination:
Also, for any non-broadcast IPI or I/O subsystem initiated interrupt
with lowest priority delivery mode, software must ensure that APICs
defined in the interrupt address are present and enabled to receive
interrupts.
We could warn on top of that.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
False from kvm_irq_delivery_to_apic_fast() means that we don't handle it
in the fast path, but we still return false in cases that were perfectly
handled, fix that.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
0x830 MSR is 0x300 xAPIC MMIO, which is MSR_ICR.
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
x2APIC has no registers for DFR and ICR2 (see Intel SDM 10.12.1.2 "x2APIC
Register Address Space"). KVM needs to cause #GP on such accesses.
Fix it (DFR and ICR2 on read, ICR2 on write, DFR already handled on writes).
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Certain x86 instructions that use modrm operands only allow memory operand
(i.e., mod012), and cause a #UD exception otherwise. KVM ignores this fact.
Currently, the instructions that are such and are emulated by KVM are MOVBE,
MOVNTPS, MOVNTPD and MOVNTI. MOVBE is the most blunt example, since it may be
emulated by the host regardless of MMIO.
The fix introduces a new group for handling such instructions, marking mod3 as
illegal instruction.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
"platform_device_put"
The platform_device_put() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
"framebuffer_release"
The framebuffer_release() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
"mmp_unregister_path"
The mmp_unregister_path() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
"backlight_device_unregister"
The backlight_device_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
"i2c_put_adapter"
The i2c_put_adapter() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
"pci_dev_put"
The pci_dev_put() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The vfree() function performs also input parameter validation. Thus the test
around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The vfree() function performs also input parameter validation. Thus the test
around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
"uvesafb_free"
The uvesafb_free() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
"vfree"
The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Instead of checking at each call of set_phys_to_machine() whether a
new p2m page has to be allocated due to writing an entry in a large
invalid or identity area, just map those areas read only and react
to a page fault on write by allocating the new page.
This change will make the common path with no allocation much
faster as it only requires a single write of the new mfn instead
of walking the address translation tables and checking for the
special cases.
Suggested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
At start of the day the Xen hypervisor presents a contiguous mfn list
to a pv-domain. In order to support sparse memory this mfn list is
accessed via a three level p2m tree built early in the boot process.
Whenever the system needs the mfn associated with a pfn this tree is
used to find the mfn.
Instead of using a software walked tree for accessing a specific mfn
list entry this patch is creating a virtual address area for the
entire possible mfn list including memory holes. The holes are
covered by mapping a pre-defined page consisting only of "invalid
mfn" entries. Access to a mfn entry is possible by just using the
virtual base address of the mfn list and the pfn as index into that
list. This speeds up the (hot) path of determining the mfn of a
pfn.
Kernel build on a Dell Latitude E6440 (2 cores, HT) in 64 bit Dom0
showed following improvements:
Elapsed time: 32:50 -> 32:35
System: 18:07 -> 17:47
User: 104:00 -> 103:30
Tested with following configurations:
- 64 bit dom0, 8GB RAM
- 64 bit dom0, 128 GB RAM, PCI-area above 4 GB
- 32 bit domU, 512 MB, 8 GB, 43 GB (more wouldn't work even without
the patch)
- 32 bit domU, ballooning up and down
- 32 bit domU, save and restore
- 32 bit domU with PCI passthrough
- 64 bit domU, 8 GB, 2049 MB, 5000 MB
- 64 bit domU, ballooning up and down
- 64 bit domU, save and restore
- 64 bit domU with PCI passthrough
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Today get_phys_to_machine() is always called when the mfn for a pfn
is to be obtained. Add a wrapper __pfn_to_mfn() as inline function
to be able to avoid calling get_phys_to_machine() when possible as
soon as the switch to a linear mapped p2m list has been done.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Introduces lookup_pmd_address() to get the address of the pmd entry
related to a virtual address in the current address space. This
function is needed for support of a virtual mapped sparse p2m list
in xen pv domains, as we need the address of the pmd entry, not the
one of the pte in that case.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
When the physical memory configuration is initialized the p2m entries
for not pouplated memory pages are set to "invalid". As those pages
are beyond the hypervisor built p2m list the p2m tree has to be
extended.
This patch delays processing the extra memory related p2m entries
during the boot process until some more basic memory management
functions are callable. This removes the need to create new p2m
entries until virtual memory management is available.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
The m2p overrides are used to be able to find the local pfn for a
foreign mfn mapped into the domain. They are used by driver backends
having to access frontend data.
As this functionality isn't used in early boot it makes no sense to
initialize the m2p override functions very early. It can be done
later without doing any harm, removing the need for allocating memory
via extend_brk().
While at it make some m2p override functions static as they are only
used internally.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Early in the boot process the memory layout of a pv-domain is changed
to match the E820 map (either the host one for Dom0 or the Xen one)
regarding placement of RAM and PCI holes. This requires removing memory
pages initially located at positions not suitable for RAM and adding
them later at higher addresses where no restrictions apply.
To be able to operate on the hypervisor supported p2m list until a
virtual mapped linear p2m list can be constructed, remapping must
be delayed until virtual memory management is initialized, as the
initial p2m list can't be extended unlimited at physical memory
initialization time due to it's fixed structure.
A further advantage is the reduction in complexity and code volume as
we don't have to be careful regarding memory restrictions during p2m
updates.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
