| Age | Commit message (Collapse) | Author |
|---|
|
Port link change with port in resume state should not be
reported to usbcore, as this is an internal state to be
handled by xhci driver. Reporting PLC to usbcore may
cause usbcore clearing PLC first and port change event irq
won't be generated.
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the link is just waken, it's in Resume state, and driver sets PLS to
U0. This refers to Phase 1. Phase 2 refers to when the link has completed
the transition from Resume state to U0.
With the fix of xhci: report U3 when link is in resume state, it also
exposes an issue that usb3 roothub and controller can suspend right
after phase 1, and this causes a hard hang in controller.
To fix the issue, we need to prevent usb3 bus suspend if any port is
resuming in phase 1.
[merge separate USB2 and USB3 port resume checking to one -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_hub_report_usb3_link_state() returns pls as U0 when the link
is in resume state, and this causes usb core to think the link is in
U0 while actually it's in resume state. When usb core transfers
control request on the link, it fails with TRB error as the link
is not ready for transfer.
To fix the issue, report U3 when the link is in resume state, thus
usb core knows the link it's not ready for transfer.
Cc: <stable@vger.kernel.org>
Signed-off-by: Zhuang Jin Can <jin.can.zhuang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When resetting a device the number of active TTs may need to be
corrected by xhci_update_tt_active_eps, but the number of old active
endpoints supplied to it was always zero, so the number of TTs and the
bandwidth reserved for them was not updated, and could rise
unnecessarily.
This affected systems using Intel's Patherpoint chipset, which rely on
software bandwidth checking. For example, a Lenovo X230 would lose the
ability to use ports on the docking station after enough suspend/resume
cycles because the bandwidth calculated would rise with every cycle when
a suitable device is attached.
The correct number of active endpoints is calculated in the same way as
in xhci_reserve_bandwidth.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Campbell <bacam@z273.org.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
virt_dev->num_cached_rings counts on freed ring and is not updated
correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring
is added into cache and then num_rings_cache is incremented as below:
virt_dev->ring_cache[rings_cached] =
virt_dev->eps[ep_index].ring;
virt_dev->num_rings_cached++;
here, free ring pointer is added to a current index and then
index is incremented.
So current index always points to empty location in the ring cache.
For getting available free ring, current index should be decremented
first and then corresponding ring buffer value should be taken from ring
cache.
But In function xhci_endpoint_init(), the num_rings_cached index is
accessed before decrement.
virt_dev->eps[ep_index].new_ring =
virt_dev->ring_cache[virt_dev->num_rings_cached];
virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL;
virt_dev->num_rings_cached--;
This is bug in manipulating the index of ring cache.
And it should be as below:
virt_dev->num_rings_cached--;
virt_dev->eps[ep_index].new_ring =
virt_dev->ring_cache[virt_dev->num_rings_cached];
virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL;
Cc: <stable@vger.kernel.org>
Signed-off-by: Aman Deep <aman.deep@samsung.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xHCI in Intel CherryView / Braswell Platform requires
a driver workaround to get xHCI D3 working. Without this
workaround, xHCI might not enter D3.
Workaround is to configure SSIC PORT as "unused" before D3
entry and "used" after D3 exit. This is done through a
vendor specific register (PORT2_SSIC_CONFIG_REG2 at offset
0x883c), in xhci suspend / resume callbacks.
Verified xHCI D3 works fine in CherryView / Braswell platform.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel xhci hw that require XHCI_PME_STUCK quirk have as default disabled
xhci from going to D3 state in runtime suspend. Driver needs to verify
it can deal with the hw by calling an ACPI _DSM method to get D3 enabled.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
I'm not aware of any existing bugs around this, but the expectation is
that nfs_mark_for_revalidate() should always force a revalidation of
the cached metadata.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Setting the change attribute has been mandatory for all NFS versions, since
commit 3a1556e8662c ("NFSv2/v3: Simulate the change attribute"). We should
therefore not have anything be conditional on it being set/unset.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
We can't allow caching of data until the change attribute has been
initialised correctly.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
If we've ensured that the size and the change attribute are both correct,
then there is no point in marking those attributes as needing revalidation
again. Only do so if we know the size is incorrect and was not updated.
Fixes: f2467b6f64da ("NFS: Clear NFS_INO_REVAL_PAGECACHE when...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
pNFS writes don't return attributes, however that doesn't mean that we
should ignore the fact that they may be extending the file. This patch
ensures that if a write is seen to extend the file, then we always set
an attribute barrier, and update the cached file size.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Otherwise, nfs4_select_rw_stateid() will always return the zero stateid
instead of the correct open stateid.
Fixes: f95549cf24660 ("NFSv4: More CLOSE/OPEN races")
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Calling xprt_complete_bc_request() effectively causes the slot to be allocated,
so it needs to decrement the backchannel free slot count as well.
Fixes: 0d2a970d0ae5 ("SUNRPC: Fix a backchannel race")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
xprt_alloc_bc_request() cannot call xprt_free_bc_request() without
deadlocking, since it already holds the xprt->bc_pa_lock.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Fixes: 0d2a970d0ae55 ("SUNRPC: Fix a backchannel race")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
end_cmd finishes request associated with nullb_cmd struct, so we
should save pointer to request_queue in a local variable before
calling end_cmd.
The problem was causes general protection fault with slab poisoning
enabled.
Fixes: 8b70f45e2eb2 ("null_blk: restart request processing on completion handler")
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.2-rc4
Only four fixes this time so I'll describe them all.
We have an iomen resource leak fix in mv_udc_core. This bug
exists since v3.3.
Renesas got a fix for how they use dma_map_single() with IOMMU.
The new ulpi bus got an ordering fix, so drivers don't try to
probe ahead of the bus.
And finally, we have a fix for a really old regression with
dwc3, one which could only be exposed by a recent patch from
Subbaraya. Basically, we were startving the controller of
transfer resources.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull ARM64 fixes from Catalin Marinas:
- arm64 build fix following the move of the thread_struct to the end of
task_struct and the asm offsets becoming too large for the AArch64
ISA
- preparatory patch for moving irq_data struct members (applied now to
reduce dependency for the next merging window)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
ARM64/irq: Use access helper irq_data_get_affinity_mask()
arm64: switch_to: calculate cpu context pointer using separate register
|
|
Running `make modules_install` ordinarily will overwrite existing
modules. This is the desired behavior, and is how pretty much every
other `make install` target works.
However, if CONFIG_MODULE_COMPRESS is enabled, modules are passed
through gzip and xz which then do the file writing. Both gzip and xz
will error out if the file already exists, unless -f is passed.
This patch adds -f so that the behavior is uniform.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
|
|
Initialize the ARCH_* overrides before including the arch Makefile, to
avoid picking up the values from the environment. The variables can
still be overriden on the make command line, but this won't happen
by accident.
Signed-off-by: Michal Marek <mmarek@suse.com>
|
|
Two nice things here:
- drm_dev_register will truly register everything in the right order
if the driver doesn't have a ->load callback. Before this we had to
init the primary mode_group after the device nodes where already
registered.
- Less things to keep track of when reworking the connector locking,
yay!
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
It's been dead code since forever since mode groups haven't ever been
implemented. On top of that it's also been non-functional since we
only ever filtered the getresources ioctl and not any of the others
nor the mode object lookup code.
Given overwhelming evidence it looks like this isn't a feature we
need, hence remove it.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Remaining manual work in the drm core&helpers. Nothing special here,
no surprises.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This function takes two locks, both of them the wrong ones. This
wasn't an oversight from my fb locking rework since both patches
landed in parallel. We really only need fb_lock when walking that
list, since everything we can reach from that is refcounted properly
already.
v2: Drop unused dev spotted by 0day.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
region_is_ram() looks up the iomem_resource table to check if
a target range is in RAM. However, it always returns with -1
due to invalid range checks. It always breaks the loop at the
first entry of the table.
Another issue is that it compares p->flags and flags, but it always
fails. flags is declared as int, which makes it as a negative value
with IORESOURCE_BUSY (0x80000000) set while p->flags is unsigned long.
Fix the range check and flags so that region_is_ram() works as
advertised.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/1437088996-28511-4-git-send-email-toshi.kani@hp.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
__ioremap_caller() calls region_is_ram() to walk through the
iomem_resource table to check if a target range is in RAM, which was
added to improve the lookup performance over page_is_ram() (commit
906e36c5c717 "x86: use optimized ioresource lookup in ioremap
function"). page_is_ram() was no longer used when this change was
added, though.
__ioremap_caller() then calls walk_system_ram_range(), which had
replaced page_is_ram() to improve the lookup performance (commit
c81c8a1eeede "x86, ioremap: Speed up check for RAM pages").
Since both checks walk through the same iomem_resource table for
the same purpose, there is no need to call both functions.
Aside of that walk_system_ram_range() is the only useful check at the
moment because region_is_ram() always returns -1 due to an
implementation bug. That bug in region_is_ram() cannot be fixed
without breaking existing ioremap callers, which rely on the subtle
difference of walk_system_ram_range() versus non page aligned ranges.
Once these offending callers are fixed we can use region_is_ram() and
remove walk_system_ram_range().
[ tglx: Massaged changelog ]
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/1437088996-28511-3-git-send-email-toshi.kani@hp.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
__ioremap_check_ram() has a WARN_ONCE() which is emitted when the
given pfn range is not RAM. The warning is bogus in two aspects:
- it never triggers since walk_system_ram_range() only calls
__ioremap_check_ram() for RAM ranges.
- the warning message is wrong as it says: "ioremap on RAM' after it
established that the pfn range is not RAM.
Move the WARN_ONCE() to __ioremap_caller(), and update the message to
include the address range so we get an actual warning when something
tries to ioremap system RAM.
[ tglx: Massaged changelog ]
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/1437088996-28511-2-git-send-email-toshi.kani@hp.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When zones were originally introduced, the expectation functions were
all extended to perform lookup using the zone. However, insertion was
not modified to check the zone. This means that two expectations which
are intended to apply for different connections that have the same tuple
but exist in different zones cannot both be tracked.
Fixes: 5d0aa2ccd4 (netfilter: nf_conntrack: add support for "conntrack zones")
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Now that we also grab the connection_mutex and so fixed the race with
atomic modeset we can use the iterator there too.
The other special case is drm_connector_unplug_all which would have a
locking inversion with the sysfs store/show functions if we'd grab the
mode_config.mutex around the unplug. We could just grab
connection_mutex instead, but that's a bit too much a dirty trick for
my taste. Also it's only used by udl, which doesn't do any other kind
of connector hotplugging, so should be race-free. Hence just stick
with a comment for now.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Now that dp mst hotplug takes all locks we can amend the locking rules
for the iterators. This is needed before we can roll these out in the
atomic code to avoid getting burried in WARNINGs.
v2: Rebase onto the extracted list locking assert and add a comment to
explain the rules.
v3: Fixup German->English translation fail in the comment.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Similar with the i915 take all modeset locks for mst hotplug. This is
needed to make sure radeon holds both mode_config.mutex and
mode_config.connection_mutex when updating the connector_list, which
is the new (interim) locking regime we want for that.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
While auditing various users of the connector/encoder lists I realized
that the atomic code is a very prolific user of them. And it only ever
grabs the mode_config->connection_mutex, but not the
mode_config->mutex like all the other code walking encoder/connector
lists.
The problem is that we can't grab the mode_config.mutex late in atomic
code since that would lead to locking inversions. And we don't want to
grab it unconditionally like the legacy set_config modeset path since
that would render all the fine-grained locking moot.
Instead just grab more locks in the dp mst hotplug code. Note that
drm_connector_init (which is the one adding the connector to these
lists) already uses drm_modeset_lock_all.
The other reason for grabbing all locks is that the dpms off in the
unplug function amounts to a modeset, so better to take all required
locks for that.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Ever since framebuffers are reference counted we have a special lock
for the global fb list. Make sure users of that list do hold that
lock when using the new iterators.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Just so I have a user for this macro.
v2: Use the right macro - somehow I thought gcc should scream at me,
but list_for_each isn't really typesafe unfortunately. Spotted by
Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
Because of DP MST connectors can now be hotplugged and we must hold
the right lock when walking the connector lists. Enforce this by
checking the locking in our shiny new list walking macros.
v2: Extract the locking check into a small static inline helper to
help readability. This will be more important when we make the
read list access rules more complicated in later patches. Inspired by
comments from Chris. Unfortunately, due to header loops around the
definition of struct drm_device the function interface is a bit funny.
v3: Encoders aren't hotadded/removed. For each dp mst encoder we
statically create one fake encoder per pipe so that we can support as
many mst sinks as the hw can (Dave).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
drm_fb_helper_single_add_all_connectors
This is now truly only duct-tape to keep locking checks happy since
calling this function when hpd or polling are already enabled is a
bug. The fbdev helper can't cope with hotplug changes yet at this
point, only after that.
Otoh a bit more robustness in this function can't hurt, and with this
fbdev can actually cope with hotplug changes. And it's also more
consistent with the connector hotadd/remove dp mst needs to do.
Therefore document this as new official behavior.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
So on first looks this seems superflous since drivers should ensure
correct ordering to not make this a problem. Otoh ordering constraints
between hdp, fbdev load and enabling polling are already tricky on
some hardware and it helps to be more robust.
But the real goal is to just shut up a locking WARN_ON I'd like to
add, which means init code gets some additional locks just for
uniformity.
v2: Also grab the lock for the public poll_enable, not just poll_init
which is used for resume, with the same justification.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
And roll them out across drm_* files. The point here isn't code
prettification (it helps with that too) but that some of these lists
aren't static any more. And having macros will gives us a convenient
place to put locking checks into.
I didn't add an iterator for props since that's only used by a
list_for_each_entry_safe in the driver teardown code.
Search&replace was done with the below cocci spatch. Note that there's
a bunch more places that didn't match and which would need some manual
changes, but I've intentially left these out for this mostly automated
patch.
iterator name drm_for_each_crtc;
struct drm_crtc *crtc;
struct drm_device *dev;
expression head;
@@
- list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
+ drm_for_each_crtc (crtc, dev) {
...
}
@@
iterator name drm_for_each_encoder;
struct drm_encoder *encoder;
struct drm_device *dev;
expression head;
@@
- list_for_each_entry(encoder, &dev->mode_config.encoder_list, head) {
+ drm_for_each_encoder (encoder, dev) {
...
}
@@
iterator name drm_for_each_fb;
struct drm_framebuffer *fb;
struct drm_device *dev;
expression head;
@@
- list_for_each_entry(fb, &dev->mode_config.fb_list, head) {
+ drm_for_each_fb (fb, dev) {
...
}
@@
iterator name drm_for_each_connector;
struct drm_connector *connector;
struct drm_device *dev;
expression head;
@@
- list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
+ drm_for_each_connector (connector, dev) {
...
}
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
No need to pass the planelist when everyone just uses
dev->mode_config.plane_list anyway.
I want to add a pile more of iterators with unified (obj, dev)
arguments. This is just prep.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This fixes an issue introduced in commit b23c843992b6 (usb: dwc3:
gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would
only use DEPSTARTCFG once per SetConfig.
The trick is that we should use one DEPSTARTCFG per SetConfig *OR*
SetInterface. SetInterface was completely missed from the original
patch.
This problem became aparent after commit 76e838c9f776 (usb: dwc3:
gadget: return error if command sent to DEPCMD register fails)
added checking of the return status of device endpoint commands.
'Set Endpoint Transfer Resource' command was caught failing
occasionally. This is because the Transfer Resource
Index was not getting reset during a SET_INTERFACE request.
Finally, to fix the issue, was we have to do is make sure that
our start_config_issued flag gets reset whenever we receive a
SetInterface request.
To verify the problem (and its fix), all we have to do is run
test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'.
Tested-by: Huang Rui <ray.huang@amd.com>
Tested-by: Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com>
Fixes: b23c843992b6 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs)
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It's causing piles of issues since we've stopped forcing full detect
cycles in the sysfs interfaces with
commit c484f02d0f02fbbfc6decc945a69aae011041a27
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Mar 6 12:36:42 2015 +0000
drm: Lighten sysfs connector 'status'
The original justification for this was that the hpd handlers could
use the unknown state as a hint to force a full detection. But current
i915 code isn't doing that any more, and no one else really uses reset
on resume. So instead just keep the old state around.
References: http://article.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/62584
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=100641
Cc: Rui Matos <tiagomatos@gmail.com>
Cc: Julien Wajsberg <felash@gmail.com>
Cc: kuddel.mail@gmx.de
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: stable@vger.kernel.org
Acked-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rui Tiago Cação Matos <tiagomatos@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Commit 0c8c0f03e3a2 ("x86/fpu, sched: Dynamically allocate 'struct fpu'")
moved the thread_struct to the bottom of task_struct. As a result, the
offset is now too large to be used in an immediate add on arm64 with
some kernel configs:
arch/arm64/kernel/entry.S: Assembler messages:
arch/arm64/kernel/entry.S:588: Error: immediate out of range
arch/arm64/kernel/entry.S:597: Error: immediate out of range
This patch calculates the offset using an additional register instead of
an immediate offset.
Fixes: 0c8c0f03e3a2 ("x86/fpu, sched: Dynamically allocate 'struct fpu'")
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The regmap_write in ssm4567_set_dai_fmt accidentally clears the
TDM_BCLKS field which was set earlier by ssm4567_set_tdm_slot.
This patch fixes it by using regmap_update_bits with proper mask.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Currently, below code actually does not update any bit because
SGTL5000_SMALL_POP is 0.
snd_soc_update_bits(codec, SGTL5000_CHIP_REF_CTRL, SGTL5000_SMALL_POP, 1);
The SGTL5000_SMALL_POP should be BIT(0) rather than 0, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-By: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is needed as the CRC PMIC has support for Panel
enable/diable as gpio which needs 'gpiod_add_lookup_table'
and 'gpiod_remove_lookup_table' from gpiolib. This patch
can be squashed with below commit in topic/crc-pmic branch
commit 61dd2ca2d44e493b050adbbb75bc50db11c367dd
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Fri Jun 26 14:32:05 2015 +0530
mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO
signal
On some Intel SoC platforms, the panel enable/disable signals
are controlled by CRC PMIC. Add those control as a new GPIO in a
lookup table for gpio-crystalcove chip during CRC driver load
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This is a requirement for enabling display port HPD support on the port
A HPD pin. This support is to be added by follow-up patches.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Currently HPD_PORT_A is used as an alias for HPD_NONE to mean that the
given port doesn't support long/short HPD pulse detection. SDVO and CRT
ports are like this and for these ports we only want to know whether an
hot plug event was detected on the corresponding pin. Since at least on
BXT we need long/short pulse detection on PORT A as well (added by the
next patch) remove this aliasing of HPD_PORT_A/HPD_NONE and let the
return value of intel_hpd_pin_to_port() show whether long/short pulse
detection is supported on the passed in pin.
No functional change.
v2:
- rebase on top of -nightly (Daniel)
- make the check for intel_hpd_pin_to_port() return value more readable
(Sivakumar)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
These functions are quite similar, so combine them with the use of a new
argument for a function that detects long pulses. This will be also
needed by an upcoming patch adding support for BXT long pulse detection.
No functional change.
v2:
- rebase on top -nightly (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Without this patch, the headset mic will not work on this machine.
BugLink: https://bugs.launchpad.net/bugs/1476987
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
