| Age | Commit message (Collapse) | Author |
|---|
|
The VF uses a multi-bit update request to clear unused VLANs whenever it
resets. However, an accident in a previous refector broke multi-bit
updates for VFs, due to misreading a comment in fm10k_vf.c and
attempting to reduce code duplication. The problem occurs because
a multi-bit request has a non-zero length, and the PF would simply drop
any request with the upper 16 bits set.
We can't simply remove the check of the upper 16 bits and the call to
fm10k_iov_select vid, because this would remove the checks for default
VID and for ensuring no other VLANs can be enabled except pf_vid when it
has been set. To resolve that issue, this revision uses the
iov_select_vid when we have a single-bit update, and denies any
multi-bit update when the VLAN was administratively set by the PF. This
should be ok since the PF properly updates VLAN_TABLE when it assigns
the PF vid. This ensures that requests to add or remove the PF vid work
as expected, but a rogue VF could not use the multi-bit update as
a loophole to attempt receiving traffic on other VLANs.
Reported-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
commit b7d3e3d3d21a ("net: thunderx: Don't leak phy device references
on -EPROBE_DEFER condition.") incorrectly moved the call to
of_node_put() outside of the loop. Under normal loop exit, the node
has already had of_node_put() called, so the extra call results in:
[ 8.228020] ERROR: Bad of_node_put() on /soc@0/pci@848000000000/mrml-bridge0@1,0/bgx0/xlaui00
[ 8.239433] CPU: 16 PID: 608 Comm: systemd-udevd Not tainted 4.6.0-rc1-numa+ #157
[ 8.247380] Hardware name: www.cavium.com EBB8800/EBB8800, BIOS 0.3 Mar 2 2016
[ 8.273541] Call trace:
[ 8.273550] [<fffffc0008097364>] dump_backtrace+0x0/0x210
[ 8.273557] [<fffffc0008097598>] show_stack+0x24/0x2c
[ 8.273560] [<fffffc0008399ed0>] dump_stack+0x8c/0xb4
[ 8.273566] [<fffffc00085aa828>] of_node_release+0xa8/0xac
[ 8.273570] [<fffffc000839cad8>] kobject_cleanup+0x8c/0x194
[ 8.273573] [<fffffc000839c97c>] kobject_put+0x44/0x6c
[ 8.273576] [<fffffc00085a9ab0>] of_node_put+0x24/0x30
[ 8.273587] [<fffffc0000bd0f74>] bgx_probe+0x17c/0xcd8 [thunder_bgx]
[ 8.273591] [<fffffc00083ed220>] pci_device_probe+0xa0/0x114
[ 8.273596] [<fffffc0008473fbc>] driver_probe_device+0x178/0x418
[ 8.273599] [<fffffc000847435c>] __driver_attach+0x100/0x118
[ 8.273602] [<fffffc0008471b58>] bus_for_each_dev+0x6c/0xac
[ 8.273605] [<fffffc0008473884>] driver_attach+0x30/0x38
[ 8.273608] [<fffffc00084732f4>] bus_add_driver+0x1f8/0x29c
[ 8.273611] [<fffffc0008475028>] driver_register+0x70/0x110
[ 8.273617] [<fffffc00083ebf08>] __pci_register_driver+0x60/0x6c
[ 8.273623] [<fffffc0000bf0040>] bgx_init_module+0x40/0x48 [thunder_bgx]
[ 8.273626] [<fffffc0008090d04>] do_one_initcall+0xcc/0x1c0
[ 8.273631] [<fffffc0008198abc>] do_init_module+0x68/0x1c8
[ 8.273635] [<fffffc0008125668>] load_module+0xf44/0x11f4
[ 8.273638] [<fffffc0008125b64>] SyS_finit_module+0xb8/0xe0
[ 8.273641] [<fffffc0008093b30>] el0_svc_naked+0x24/0x28
Go back to the previous (correct) code that only did the extra
of_node_put() call on early exit from the loop.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
fix some exynos regressions.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Use VIDEO_SAMSUNG_S5P_G2D=n as G2D Kconfig dependency
drm/exynos: fix a warning message
drm/exynos: mic: fix an error code
drm/exynos: fimd: fix broken dp_clock control
drm/exynos: build fbdev code conditionally
drm/exynos: fix adjusted_mode pointer in exynos_plane_mode_set
drm/exynos: fix error handling in exynos_drm_subdrv_open
|
|
into drm-fixes
some misc radeon fixes.
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/amdgpu: fix irq domain remove for tonga ih
drm/radeon: use helper for mst connector dpms.
drm/radeon/mst: port some MST setup code from DAL.
drm/amdgpu: add invisible pin size statistic
|
|
Add validation code into mISDN/socket.c
Signed-off-by: Emrah Demir <ed@abdsec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses a bug introduced based on my interpretation of the
XL710 datasheet. Specifically section 8.4.1 states that "A single transmit
packet may span up to 8 buffers (up to 8 data descriptors per packet
including both the header and payload buffers)." It then later goes on to
say that each segment for a TSO obeys the previous rule, however it then
refers to TSO header and the segment payload buffers.
I believe the actual limit for fragments with TSO and a skbuff that has
payload data in the header portion of the buffer is actually only 7
fragments as the skb->data portion counts as 2 buffers, one for the TSO
header, and one for a segment payload buffer.
Fixes: 2d37490b82af ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
f1705ec197e7 added the option to retain user configured addresses on an
admin down. A comment to one of the later revisions suggested using the
IFA_F_PERMANENT flag rather than adding a user_managed boolean to the
ifaddr struct. A side effect of this change is that link local and
loopback addresses are also retained which is not part of the objective
of f1705ec197e7. Add check to drop those addresses.
Fixes: f1705ec197e7 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clk API may return 0 on clk_get_rate, so we should check the result before
using it as a divisor.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree. More
specifically, they are:
1) Fix missing filter table per-netns registration in arptables, from
Florian Westphal.
2) Resolve out of bound access when parsing TCP options in
nf_conntrack_tcp, patch from Jozsef Kadlecsik.
3) Prefer NFPROTO_BRIDGE extensions over NFPROTO_UNSPEC in ebtables,
this resolves conflict between xt_limit and ebt_limit, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.6
b43
* fix memory leaks when removing the device
bcma
* fix building without OF_IRQ
rtlwifi
* fix gcc-6 indentation warning
iwlwifi
* lower the debug level of a benign print
* fix a memory leak
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull arch/sh fixes from Rich Felker:
"Fixes for two arch/sh build regressions that appeared in 4.6-rc1, one
introduced by me, and one caused by changes elsewhere"
* tag 'sh-fixes-4.6-rc1' of git://git.libc.org/linux-sh:
sh: fix function signature of cpu_coregroup_mask to match pointer type
sh: fix smp-shx3 build regression from removal of arch localtimer
|
|
USB1 controller is hardwired to be used as Host only port so
we don't need to check ID pin state and can get rid of extcon_usb1.
This also reduces USB1 controller's and so eSATA power's dependency
with EXTCON. This fixes eSATA port with multi_v7_defconfig.
Cc: Franklin S Cooper Jr. <fcooper@ti.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
[tony@atomide.com: updated to describe what it fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.
Fixes: cce1ee000187 ("ARM: DTS: am437x: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.
Fixes: b5e509066074 ("ARM: DTS: am33xx: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/fixes
ARM: OMAP2+: clockdomain: another fix for v4.6-rc
For DRA7xx platforms, add a workaround for missed timer interrupts
that appears to be due to an integration bug (erratum i874)
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/omap-fixes-b-for-v4.6-rc/20160413020850/
(The DRA7xx board here has not yet been added into the testbed.)
|
|
When a buffer is being dequeued using VIDIOC_DQBUF IOCTL, the exact buffer
which will be dequeued is not known until the buffer has been removed from
the queue. The number of planes is specific to a buffer, not to the queue.
This does lead to the situation where multi-plane buffers may be requested
and queued with n planes, but VIDIOC_DQBUF IOCTL may be passed an argument
struct with fewer planes.
__fill_v4l2_buffer() however uses the number of planes from the dequeued
videobuf2 buffer, overwriting kernel memory (the m.planes array allocated
in video_usercopy() in v4l2-ioctl.c) if the user provided fewer
planes than the dequeued buffer had. Oops!
Fixes: b0e0e1f83de3 ("[media] media: videobuf2: Prepare to divide videobuf2")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v4.4 and later
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The number of planes in videobuf2 is specific to a buffer. In order to
verify that the planes array provided by the user is long enough, a new
vb2_buf_op is required.
Call __verify_planes_array() when the dequeued buffer is known. Return an
error to the caller if there was one, otherwise remove the buffer from the
done list.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v4.4 and later
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
AMD Seattle SATA controller mostly conforms to AHCI interface with some
special register to control SGPIO interface. In the case of an AHCI
controller, the SGPIO feature is ideally implemented using the
"Enclosure Management" register of the AHCI controller, but those
registeres are not implemented in the Seattle SoC. Instead SoC
(Rev B0 onwards) provides a 32-bit SGPIO control register which should
be programmed to control the activity, locate and fault LEDs.
The driver is based on ahci_platform driver.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: tj@kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
On BXT platform Host Controller and Device Controller figure as
same PCI device but with different device function. HCD should
not pass data to Device Controller but only to Host Controllers.
Checking if companion device is Host Controller, otherwise skip.
Cc: <stable@vger.kernel.org>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Cc: stable@vger.kernel.org
Reported-and-tested-by: David Webb <djw@noc.ac.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 64d513ac31bd ("scsi: use host wide tags by default") causes
the SCSI core to queue more commands then we can handle on devices with
multiple LUNs, limit the queue depth at the scsi-host level instead of
per slave to fix this.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1315013
Cc: stable@vger.kernel.org # 4.4.x and 4.5.x
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It tries to "match" drivers for each interface (not "much").
Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Otherwise generic-xhci and xhci-platform which have no data get wrongly
detected as XHCI_PLAT_TYPE_MARVELL_ARMADA by xhci_plat_type_is().
This fixes a regression in v4.5 for STiH407 family SoC's which use the
synopsis dwc3 IP, whereby the disable_clk error path gets taken due to
wrongly being detected as XHCI_PLAT_TYPE_MARVELL_ARMADA and the hcd never
gets added.
I suspect this will also fix other dwc3 DT platforms such as Exynos,
although I've only tested on STih410 SoC.
Fixes: 4efb2f694114 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: stable@vger.kernel.org
Cc: gregory.clement@free-electrons.com
Cc: yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes some wild pointers produced by xhci_mem_cleanup.
These wild pointers will cause system crash if xhci_mem_cleanup()
is called twice.
Reported-and-tested-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue that cannot work if R-Car Gen2/3 run on
above 4GB physical memory environment to use a quirk XHCI_NO_64BIT_SUPPORT.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of
HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
address memory pointers actually. So, in this case, this driver should
call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup().
Otherwise, the xHCI controller will be died after a usb device is
connected if it runs on above 4GB physical memory environment.
So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve
such an issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Cc: <stable@vger.kernel.org>
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Broxton B0 also requires XHCI_PME_STUCK_QUIRK.
Adding PCI device ID for Broxton B and adding to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Under some circumstances acm_tty_flush_chars() is called
with no buffer to flush. We simply need to do nothing.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These identifiers are bogus. The interested architectures should define
HAVE_EFFICIENT_UNALIGNED_ACCESS whenever relevant to do so. If this
isn't true for some arch, it should be fixed in the arch definition.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on Sergey's test patch [1], this fixes zram with lz4 compression
on big endian cpus.
Note that the 64-bit preprocessor test is not a cleanup, it's part of
the fix, since those identifiers are bogus (for example, __ppc64__
isn't defined anywhere else in the kernel, which means we'd fall into
the 32-bit definitions on ppc64).
Tested on ppc64 with no regression on x86_64.
[1] http://marc.info/?l=linux-kernel&m=145994470805853&w=4
Cc: stable@vger.kernel.org
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit 895005202987 ("dmaengine: dw: apply both HS interfaces and remove
slave_id usage") cleaned up the code to avoid usage of depricated slave_id
member of generic slave configuration.
Meanwhile it broke the master selection by removing important call to
dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from
custom slave configuration to the internal channel structure.
Everything works until now since there is no customized connection of
DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use.
The configurations where 2 masters are connected to the different masters are
not working anymore. We are expecting one user of such configuration and need
to select masters properly. Besides that it is obviously a performance
regression since only one master is in use in multi-master configuration.
Select masters in accordance with what user asked for. Keep this patch in a form
more suitable for back porting.
We are safe to take necessary data in ->device_alloc_chan_resources() because
we don't support generic slave configuration embedded into custom one, and thus
the only way to provide such is to use the parameter to a filter function which
is called exactly before channel resource allocation.
While here, replase BUG_ON to less noisy dev_warn() and prevent channel
allocation in case of error.
Fixes: 895005202987 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu/coldfire fix from Greg Ungerer:
"Only a single change that removes a local arch specific gpio bus sysfs
device that now clashes with the generic gpio bus sysfs device
interface"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k/gpio: remove arch specific sysfs bus device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes for -rc4, for various platforms.
Nothing really substantial and worth pointing out in particular; small
fixes for various bugs, see shortlog for details"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: sa1100: remove references to the defunct handhelds.org
bus: uniphier-system-bus: fix condition of overlap check
ARM: uniphier: drop weird sizeof()
ARM: dts: am335x-baltos-ir5221: fix cpsw_emac0 link type
ARM: OMAP: Correct interrupt type for ARM TWD
ARM: DRA722: Add ID detect for Silicon Rev 2.0
ARM: dts: am43xx: fix edma memcpy channel allocation
ARM: dts: AM43x-epos: Fix clk parent for synctimer
ARM: OMAP2: Fix up interconnect barrier initialization for DRA7
documentation: Fix pinctrl documentation for Meson8 / Meson8b
ARM: dts: amlogic: Split pinctrl device for Meson8 / Meson8b
ARM: mvebu: Correct unit address for linksys
bus: mvebu-mbus: use %pa to print phys_addr_t
arm64: dts: vulcan: Update PCI ranges
ARM: u8500_defconfig: turn on the Synaptics RMI4 driver
ARM: pxa: fix the number of DMA requestor lines
ARM: OMAP2+: hwmod: Fix updating of sysconfig register
ARM: OMAP2+: Use srst_udelay for USB on dm814x
|
|
Pull KVM fixes from Radim Krčmář:
"ARM fixes:
- Wrong indentation in the PMU code from the merge window
- A long-time bug occuring with running ntpd on the host, candidate
for stable
- Properly handle (and warn about) the unsupported configuration of
running on systems with less than 40 bits of PA space
- More fixes to the PM and hotplug notifier stuff from the merge
window
x86:
- leak of guest xcr0 (typically shows up as SIGILL)
- new maintainer (who is sending the pull request too)
- fix for merge window regression
- fix for guest CPUID"
Paolo Bonzini points out:
"For the record, this tag is signed by me because I prepared the pull
request. Further pull requests for 4.6 will be signed and sent out by
Radim directly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: mask CPUID(0xD,0x1).EAX against host value
kvm: x86: do not leak guest xcr0 into host interrupt handlers
KVM: MMU: fix permission_fault()
KVM: new maintainer on the block
arm64: KVM: unregister notifiers in hyp mode teardown path
arm64: KVM: Warn when PARange is less than 40 bits
KVM: arm/arm64: Handle forward time correction gracefully
arm64: KVM: Add braces to multi-line if statement in virtual PMU code
|
|
The emmc-phy occupies a contiguous set of 8 registers inside the general
register files, so the reg property should specify this.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The emmc-phy is fully enclosed in the general register files (GRF).
Therefore as seen from the device-tree it shouldn't be a separate platform-
device but instead a sub-device of the GRF - using the simply-mfd mechanism.
The driver entered the kernel in the current merge-window, so we can still
adapt the binding without needing a fallback, as the binding hasn't been
released with a full kernel yet.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The displayport-phy is fully enclosed in the general register files (GRF).
Therefore as seen from the device-tree it shouldn't be a separate platform-
device but instead a sub-device of the GRF - using the simply-mfd mechanism.
The driver entered the kernel in the current merge-window, so we can still
adapt the binding without needing a fallback, as the binding hasn't been
released with a full kernel yet.
While the edp phy is fully part of the GRF, it doesn't have any separate
register set there, so doesn't get any register-area assigned.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This reverts commit cc8ed76938b5cf6a54ab3d60edabaf808dc960d1
("soc: mediatek: SCPSYS: Fix double enabling of regulators") [1].
This patch fixes mt8173-evb failing boot issue. With commit [1],
genpd state will not sync to real power domain state. So some
resources such as clocks and regulators may stay in a wrong state.
There is no regulator double enabling issue on mainline kernel, so
we can refert commit [1] safely.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
When we loop over all queued machine check error records to pass them
to the registered notifiers we use llist_for_each_entry(). But the loop
calls gen_pool_free() for the entry in the body of the loop - and then
the iterator looks at node->next after the free.
Use llist_for_each_entry_safe() instead.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Cc: Gong Chen <gong.chen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/0205920@agluck-desk.sc.intel.com
Link: http://lkml.kernel.org/r/1459929916-12852-4-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
With commit 7b91369b4655 ("mmc: sdhci: Set DMA mask when adding host")
DMA access got disabled for device drivers with zero DMA mask property.
sdhci-esdhc-imx got blocked from DMA access by this. Hence: initialize
the DMA mask to enable access again.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
While the previous commit fixed the missing monitor_present flag
update, it may be still in an inconsistent state while the driver
repolls: the flag itself is updated, but the eld_valid flag and the
contents don't follow until the repoll finishes (and may be repeated
for a few times).
The basic problem is that pin_eld->monitor_present is updated in the
caller side. This should have been updated only in update_eld(). So,
the proper fix is to avoid accessing pin_eld but only spec->temp_eld.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit [bd48128539ab: ALSA: hda - Fix forgotten HDMI
monitor_present update] covered the missing update of monitor_present
flag, but this caused a regression for devices without the i915 eld
notifier. Since the old code supposed that pin_eld->monitor_present
was updated by the caller side, the hdmi_present_sense_via_verbs()
doesn't update the temporary eld->monitor_present but only
pin_eld->monitor_present, which is now overridden in update_eld().
The fix is to update pin_eld->monitor_present as well before calling
update_eld().
Note that this may still leave monitor_present flag in an inconsistent
state when the driver repolls, but this is at least the old behavior.
More proper fix will follow in the later patch.
Fixes: bd48128539ab ('ALSA: hda - Fix forgotten HDMI monitor_present update')
Signed-off-by: Hyungwon Hwang <hyungwon.hwang7@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
commit ee36027427c7 ("clk: imx: Add clock support for imx6qp")
introduced a regression due to a subtle typo in the 'can_root' clock
definition. The effect is that trying to configure the bitrate of the
can interfaces fails with -EDOM or produces a division by zero error
due to the clock_freq of the can serial clock being reported as '0'.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Fixes: ee36027427c7 ("clk: imx: Add clock support for imx6qp")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As Al pointed, d_revalidate should return RCU lookup before using d_inode.
This was originally introduced by:
commit 34286d666230 ("fs: rcu-walk aware d_revalidate method").
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: stable <stable@vger.kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into for-linus
|
|
If a requested extension exists as module and is not loaded,
ebt_check_match() might accidentally use an NFPROTO_UNSPEC one with same
name and fail.
Reproduced with limit match: Given xt_limit and ebt_limit both built as
module, the following would fail:
modprobe xt_limit
ebtables -I INPUT --limit 1/s -j ACCEPT
The fix is to make ebt_check_match() distrust a found NFPROTO_UNSPEC
extension and retry after requesting an appropriate module.
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Starting with 4.1 the tracing subsystem has its own filesystem
which is automounted in the tracing subdirectory of debugfs.
Prior to this debugfs could be bind mounted in a cloned mount
namespace, but if tracefs has been mounted under debugfs this
now fails because there is a locked child mount. This creates
a regression for container software which bind mounts debugfs
to satisfy the assumption of some userspace software.
In other pseudo filesystems such as proc and sysfs we're already
creating mountpoints like this in such a way that no dirents can
be created in the directories, allowing them to be exceptions to
some MNT_LOCKED tests. In fact we're already do this for the
tracefs mountpoint in sysfs.
Do the same in debugfs_create_automount(), since the intention
here is clearly to create a mountpoint. This fixes the regression,
as locked child mounts on permanently empty directories do not
cause a bind mount to fail.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel DNV has the same iSMT SMBus host controller than Intel Avoton. Add
DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
