| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a regression in lskcipher and an out-of-bound access
in arm64/neonbs"
* tag 'v6.8-p5' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm64/neonbs - fix out-of-bounds access on short input
crypto: lskcipher - Copy IV in lskcipher glue code always
|
|
Commit 'e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable
the domain")' aimed to make sure that a power-domain that is being
enabled without any particular performance-state requested will at least
turn the rail on, to avoid filling DeviceTree with otherwise unnecessary
required-opps properties.
But in the event that aggregation happens on a disabled power-domain, with
an enabled peer without performance-state, both the local and peer
corner are 0. The peer's enabled_corner is not considered, with the
result that the underlying (shared) resource is disabled.
One case where this can be observed is when the display stack keeps mmcx
enabled (but without a particular performance-state vote) in order to
access registers and sync_state happens in the rpmhpd driver. As mmcx_ao
is flushed the state of the peer (mmcx) is not considered and mmcx_ao
ends up turning off "mmcx.lvl" underneath mmcx. This has been observed
several times, but has been painted over in DeviceTree by adding an
explicit vote for the lowest non-disabled performance-state.
Fixes: e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable the domain")
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/linux-arm-msm/ZdMwZa98L23mu3u6@hovoldconsulting.com/
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240226-rpmhpd-enable-corner-fix-v1-1-68c004cec48c@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
hci_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific command
to trigger firmware coredump, but the command does not have any event as
its sync response, so it is not suitable to use __hci_cmd_sync(), fixed by
using __hci_cmd_send().
Fixes: 06d3fdfcdf5c ("Bluetooth: hci_qca: Add qcom devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BT adapter going into UNCONFIGURED state during BT turn ON when
devicetree has no local-bd-address node.
Bluetooth will not work out of the box on such devices, to avoid this
problem, added check to set HCI_QUIRK_USE_BDADDR_PROPERTY based on
local-bd-address node entry.
When this quirk is not set, the public Bluetooth address read by host
from controller though HCI Read BD Address command is
considered as valid.
Fixes: e668eb1e1578 ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Vendor-specific command patch config has HCI_Command_Complete event as
response, but qca_send_patch_config_cmd() wrongly expects vendor-specific
event for the command, fixed by using right event type.
Btmon log for the vendor-specific command are shown below:
< HCI Command: Vendor (0x3f|0x0000) plen 5
28 01 00 00 00
> HCI Event: Command Complete (0x0e) plen 5
Vendor (0x3f|0x0000) ncmd 1
Status: Success (0x00)
28
Fixes: 4fac8a7ac80b ("Bluetooth: btqca: sequential validation")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Right now Linux BT stack cannot pass test case "GAP/CONN/CPUP/BV-05-C
'Connection Parameter Update Procedure Invalid Parameters Central
Responder'" in Bluetooth Test Suite revision GAP.TS.p44. [0]
That was revoled by commit c49a8682fc5d ("Bluetooth: validate BLE
connection interval updates"), but later got reverted due to devices
like keyboards and mice may require low connection interval.
So only validate the max value connection interval to pass the Test
Suite, and let devices to request low connection interval if needed.
[0] https://www.bluetooth.org/docman/handlers/DownloadDoc.ashx?doc_id=229869
Fixes: 68d19d7d9957 ("Revert "Bluetooth: validate BLE connection interval updates"")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If we received HCI_EV_IO_CAPA_REQUEST while
HCI_OP_READ_REMOTE_EXT_FEATURES is yet to be responded assume the remote
does support SSP since otherwise this event shouldn't be generated.
Link: https://lore.kernel.org/linux-bluetooth/CABBYNZ+9UdG1cMZVmdtN3U2aS16AKMCyTARZZyFX7xTEDWcMOw@mail.gmail.com/T/#t
Fixes: c7f59461f5a7 ("Bluetooth: Fix a refcnt underflow problem for hci_conn")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
LIMITED_DISCOVERABLE flag is not reset from Class of Device and
advertisement on limited discoverable timeout. This prevents to pass PTS
test GAP/DISC/LIMM/BV-02-C
Calling set_discoverable_sync as when the limited discovery is set
correctly update the Class of Device and advertisement.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_store_wake_reason() wrongly parses event HCI_Connection_Request
as HCI_Connection_Complete and HCI_Connection_Complete as
HCI_Connection_Request, so causes recording wakeup BD_ADDR error and
potential stability issue, fix it by using the correct field.
Fixes: 2f20216c1d6f ("Bluetooth: Emit controller suspend and resume events")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
During our fuzz testing of the connection and disconnection process at the
RFCOMM layer, we discovered this bug. By comparing the packets from a
normal connection and disconnection process with the testcase that
triggered a KASAN report. We analyzed the cause of this bug as follows:
1. In the packets captured during a normal connection, the host sends a
`Read Encryption Key Size` type of `HCI_CMD` packet
(Command Opcode: 0x1408) to the controller to inquire the length of
encryption key.After receiving this packet, the controller immediately
replies with a Command Completepacket (Event Code: 0x0e) to return the
Encryption Key Size.
2. In our fuzz test case, the timing of the controller's response to this
packet was delayed to an unexpected point: after the RFCOMM and L2CAP
layers had disconnected but before the HCI layer had disconnected.
3. After receiving the Encryption Key Size Response at the time described
in point 2, the host still called the rfcomm_check_security function.
However, by this time `struct l2cap_conn *conn = l2cap_pi(sk)->chan->conn;`
had already been released, and when the function executed
`return hci_conn_security(conn->hcon, d->sec_level, auth_type, d->out);`,
specifically when accessing `conn->hcon`, a null-ptr-deref error occurred.
To fix this bug, check if `sk->sk_state` is BT_CLOSED before calling
rfcomm_recv_frame in rfcomm_process_rx.
Signed-off-by: Yuxuan Hu <20373622@buaa.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
During suspend, only wakeable devices can be in acceptlist, so if the
device was previously added it needs to be removed otherwise the device
can end up waking up the system prematurely.
Fixes: 3b42055388c3 ("Bluetooth: hci_sync: Fix attempting to suspend with unfiltered passive scan")
Signed-off-by: Clancy Shang <clancy.shang@quectel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
|
|
While handling the HCI_EV_HARDWARE_ERROR event, if the underlying
BT controller is not responding, the GPIO reset mechanism would
free the hci_dev and lead to a use-after-free in hci_error_reset.
Here's the call trace observed on a ChromeOS device with Intel AX201:
queue_work_on+0x3e/0x6c
__hci_cmd_sync_sk+0x2ee/0x4c0 [bluetooth <HASH:3b4a6>]
? init_wait_entry+0x31/0x31
__hci_cmd_sync+0x16/0x20 [bluetooth <HASH:3b4a 6>]
hci_error_reset+0x4f/0xa4 [bluetooth <HASH:3b4a 6>]
process_one_work+0x1d8/0x33f
worker_thread+0x21b/0x373
kthread+0x13a/0x152
? pr_cont_work+0x54/0x54
? kthread_blkcg+0x31/0x31
ret_from_fork+0x1f/0x30
This patch holds the reference count on the hci_dev while processing
a HCI_EV_HARDWARE_ERROR event to avoid potential crash.
Fixes: c7741d16a57c ("Bluetooth: Perform a power cycle when receiving hardware error event")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
There's a very confusing mistake in the code starting a HCI inquiry: We're
calling hci_dev_test_flag() to test for HCI_INQUIRY, but hci_dev_test_flag()
checks hdev->dev_flags instead of hdev->flags. HCI_INQUIRY is a bit that's
set on hdev->flags, not on hdev->dev_flags though.
HCI_INQUIRY equals the integer 7, and in hdev->dev_flags, 7 means
HCI_BONDABLE, so we were actually checking for HCI_BONDABLE here.
The mistake is only present in the synchronous code for starting an inquiry,
not in the async one. Also devices are typically bondable while doing an
inquiry, so that might be the reason why nobody noticed it so far.
Fixes: abfeea476c68 ("Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom BCM4377 driver has so far been
setting this flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag, which can simply be replaced
with HCI_QUIRK_USE_BDADDR_PROPERTY to indicate that the default address
is invalid but can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc81a ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org # 6.5
Reported-by: Felix Zhang <mrman@mrman314.tech>
Link: https://lore.kernel.org/r/77419ffacc5b4875e920e038332575a2a5bff29f.camel@mrman314.tech/
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Felix Zhang <mrman@mrman314.tech>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
ath12k uses BSD-3-Clause-Clear, not ISC.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240226180745.3195805-1-kvalo@kernel.org
|
|
Unlike the event configuration which can be modified by MHI, the
channel and controller configurations are expected to be const. And
since they are not modified locally, constify them to prevent runtime
modification.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223-mhi-const-wifi-ath11k-v1-1-51b9d42d2639@quicinc.com
|
|
Warning will appear when running P2P GO:
WARNING: suspicious RCU usage
drivers/net/wireless/ath/ath12k/mac.c:583 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.8.0-rc4-wt-ath+ #4
Call Trace:
<IRQ>
dump_stack_lvl+0x82/0xa0
dump_stack+0x14/0x20
lockdep_rcu_suspicious+0x214/0x3b0
ath12k_mac_get_ar_by_vdev_id+0x192/0x220 [ath12k]
ath12k_wmi_op_rx+0x2d7/0x1b40 [ath12k]
ath12k_mac_get_ar_by_vdev_id() requires its callers to have called
rcu_read_lock(), but in ath12k_wmi_p2p_noa_event() it is called without
doing so, and hence the warning was triggered.
Add rcu_read_lock() and rcu_read_unlock() to avoid warning.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 9411eecb60cb ("wifi: ath12k: implement handling of P2P NoA event")
Reported-by: Kalle Valo <quic_kvalo@quicinc.com>
Closes: https://lore.kernel.org/linux-wireless/87o7cusyvw.fsf@kernel.org/
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223054505.438839-1-quic_kangyang@quicinc.com
|
|
Currently buf_len field of ath11k_mhi_config_qca6390 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
There is a fail report which is caused by it:
kworker/u32:45: page allocation failure: order:4, mode:0x40c00(GFP_NOIO|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 19318 Comm: kworker/u32:45 Not tainted 6.8.0-rc3-1.gae4495f-default #1 openSUSE Tumbleweed (unreleased) 493b6d5b382c603654d7a81fc3c144d59a1dfceb
Workqueue: events_unbound async_run_entry_fn
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x60
warn_alloc+0x13a/0x1b0
? srso_alias_return_thunk+0x5/0xfbef5
? __alloc_pages_direct_compact+0xab/0x210
__alloc_pages_slowpath.constprop.0+0xd3e/0xda0
__alloc_pages+0x32d/0x350
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__kmalloc_large_node+0x72/0x110
__kmalloc+0x37c/0x480
? mhi_map_single_no_bb+0x77/0xf0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__mhi_prepare_for_transfer+0x44/0x80 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? __pfx_____mhi_prepare_for_transfer+0x10/0x10 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
device_for_each_child+0x5c/0xa0
? __pfx_pci_pm_resume+0x10/0x10
ath11k_core_resume+0x65/0x100 [ath11k a5094e22d7223135c40d93c8f5321cf09fd85e4e]
? srso_alias_return_thunk+0x5/0xfbef5
ath11k_pci_pm_resume+0x32/0x60 [ath11k_pci 830b7bfc3ea80ebef32e563cafe2cb55e9cc73ec]
? srso_alias_return_thunk+0x5/0xfbef5
dpm_run_callback+0x8c/0x1e0
device_resume+0x104/0x340
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x32/0x120
process_one_work+0x168/0x330
worker_thread+0x2f5/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe8/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Actually those buffers are used only by QMI target -> host communication.
And for WCN6855 and QCA6390, the largest packet size for that is less
than 6KB. So change buf_len field to 8KB, which results in order 1
allocation if page size is 4KB. In this way, we can at least save some
memory, and as well as decrease the possibility of allocation failure
in those scenarios.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Closes: https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223053111.29170-1-quic_bqiang@quicinc.com
|
|
This reverts commit e467e0bde881 ("drm/msm/dp: use
drm_bridge_hpd_notify() to report HPD status changes").
The commit changed the way how the MSM DP driver communicates
HPD-related events to the userspace. The mentioned commit made some of
the HPD events being reported earlier. This way userspace starts poking
around. It interacts in a bad way with the dp_bridge_detect and the
driver's state machine, ending up either with the very long delays
during hotplug detection or even inability of the DP driver to report
the display as connected.
A proper fix will involve redesigning of the HPD handling in the MSM DP
driver. It is underway, but it will be intrusive and can not be thought
about as a simple fix for the issue. Thus, revert the offending commit.
Fixes: e467e0bde881 ("drm/msm/dp: use drm_bridge_hpd_notify() to report HPD status changes")
Link: https://gitlab.freedesktop.org/drm/msm/-/issues/50
Reported-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/Zd3YPGmrprxv-N-O@hovoldconsulting.com/
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Paloma Arellano <quic_parellan@quicinc.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Patchwork: https://patchwork.freedesktop.org/patch/580313/
Link: https://lore.kernel.org/r/20240227220808.50146-1-dmitry.baryshkov@linaro.org
|
|
AC5X spec says PHY init complete bit must be polled until zero.
We see cases in which timeout can take longer than the standard
calculation on AC5X, which is expected following the spec comment above.
According to the spec, we must wait as long as it takes for that bit to
toggle on AC5X.
Cap that with 100 delay loops so we won't get stuck forever.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222191714.1216470-3-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Each time SD/mmc phy is initialized, at times, in some of
the attempts, phy fails to completes its initialization
which results into timeout error. Per the HW spec, it is
a pre-requisite to ensure a stable SD clock before a phy
initialization is attempted.
Fixes: 06c8b667ff5b ("mmc: sdhci-xenon: Add support to PHYs of Marvell Xenon SDHC")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240222200930.1277665-1-enachman@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Like many other models, the Lenovo 21J2 (ThinkBook 16 G5+ APO)
needs a quirk entry for the internal microphone to function.
Signed-off-by: Jiawei Wang <me@jwang.link>
Link: https://msgid.link/r/20240228073914.232204-2-me@jwang.link
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Lenovo 21J2 (ThinkBook 16 G5+ APO) has this new variant,
as detected with lspci:
64:00.5 Multimedia controller: Advanced Micro Devices, Inc. [AMD]
ACP/ACP3X/ACP6x Audio Coprocessor (rev 63)
Signed-off-by: Jiawei Wang <me@jwang.link>
Link: https://msgid.link/r/20240228073914.232204-1-me@jwang.link
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Andrew Lunn says:
====================
drivers: net: Convert EEE handling to use linkmode bitmaps
EEE has until recently been limited to lower speeds due to the use of
the legacy u32 for link speeds. This restriction has been lifted, with
the use of linkmode bitmaps, added in the following patches:
1f069de63602 ethtool: add linkmode bitmap support to struct ethtool_keee
1d756ff13da6 ethtool: add suffix _u32 to legacy bitmap members of struct ethtool_keee
285cc15cc555 ethtool: adjust struct ethtool_keee to kernel needs
0b3100bc8fa7 ethtool: switch back from ethtool_keee to ethtool_eee for ioctl
d80a52335374 ethtool: replace struct ethtool_eee with a new struct ethtool_keee on kernel side
This patchset converts the remaining MAC drivers still using the old
_u32 to link modes.
A couple of Intel drivers do odd things with EEE, setting the autoneg
bit. It is unclear why, no other driver does, ethtool does not display
it, and EEE is always negotiated. One patch in this series deletes
this code.
With all users of the legacy _u32 changed to link modes, the _u32
values are removed from keee, and support for them in the ethtool core
is removed.
---
Changes in v5:
- Restore zeroing eee_data.advertised in ax8817_178a
- Fix lp_advertised -> supported in ixgdb
- Link to v4: https://lore.kernel.org/r/20240218-keee-u32-cleanup-v4-0-71f13b7c3e60@lunn.ch
Changes in v4:
- Add missing conversion in igb
- Add missing conversion in r8152
- Add patch to remove now unused _u32 members
- Link to v3: https://lore.kernel.org/r/20240217-keee-u32-cleanup-v3-0-fcf6b62a0c7f@lunn.ch
Changes in v3:
- Add list of commits adding linkmodes to EEE to cover letter
- Fix grammar error in cover letter.
- Add Reviewed-by from Jacob Keller
- Link to v2: https://lore.kernel.org/r/20240214-keee-u32-cleanup-v2-0-4ac534b83d66@lunn.ch
Changes in v2:
- igb: Fix type 100BaseT to 1000BaseT.
- Link to v1: https://lore.kernel.org/r/20240204-keee-u32-cleanup-v1-0-fb6e08329d9a@lunn.ch
====================
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All MAC drivers have been converted to use the link mode members of
keee. So remove the _u32 values, and the code in the ethtool core to
convert the legacy _u32 values to link modes.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Energy Efficient Ethernet should always be negotiated with the link
peer. Don't include SUPPORTED_Autoneg in the results of get_eee() for
supported, advertised or lp_advertised, since it is
assumed. Additionally, ethtool(1) ignores the set bit, and no other
driver sets this.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the tables to make use of ETHTOOL link mode bits, rather than
the old u32 SUPPORTED speeds. Make use of the linkmode helps to set
bits and compare linkmodes. As a result, the _u32 members of keee are
no longer used, a step towards removing them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the existing linkmode helpers for bit manipulation of EEE
advertise, support and link partner support. The aim is to drop the
restricted _u32 variants in the near future.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the existing linkmode helpers for converting PHY EEE
register values into links modes, now that ethtool_keee uses link
modes, rather than u32 values.
Rework determining if EEE is active to make is similar as to how
phylib decides, and make use of a phylib helper to validate if EEE is
valid in for the current link mode. This then requires that PHYLIB is
selected.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a somewhat common pattern of using FIELD_PREP()
even for single bits, e.g.
cmd->info1 |= FIELD_PREP(HTT_SRNG_SETUP_CMD_INFO1_RING_FLAGS_MSI_SWAP,
!!(params.flags & HAL_SRNG_FLAGS_MSI_SWAP));
which might as well be written as
if (params.flags & HAL_SRNG_FLAGS_MSI_SWAP)
cmd->info1 |= HTT_SRNG_SETUP_CMD_INFO1_RING_FLAGS_MSI_SWAP;
(since info1 is fully initialized to start with), but in
a long chain of FIELD_PREP() this really seems fine.
However, it triggers a sparse warning, in the check in
the macro for whether a constant value fits into the mask,
as this contains a "& (_val)". In this case, this really
is always intentional, so just suppress the warning by
adding "0+" to the expression, indicating explicitly that
this is correct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223100146.d243b6b1a9a1.I033828b1187c6bccf086e31400f7e933bb8373e7@changeid
|
|
Moving struct ieee80211_sta *sta variable definition to the front
of the code to fix the ISO C90 forbids mixed declarations and code
warning.
Fixes: 43532c050f8e ("wifi: rtl8xxxu: support multiple interfaces in set_aifs()")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/TYAP286MB03157A408E0D69F2F6FBD88ABC552@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
This code wants to compare the obtained value, but as it also
has a special type for register addresses to find places doing
such compares and calculations wrong, we need explicit casts
here to silence sparse.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223114023.976fcd59e97a.I0bba4ef7dc2847ce8ab5ec229149e1a09413b8b9@changeid
|
|
Clearly writing __le32 was intended here, so just put the
right casts into the code to silence sparse about it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223114023.ce0c714124e9.I2b5710b761f63522574fbe7654d37151c31e0b77@changeid
|
|
sparse complains on this code about casts that lose bits
due to the usage of bitwise not, but really we do want
16 bits only, so clarify that by using masks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223114023.06e5ade90bcd.I41a0cbae1fa259cfbf5fa117ddfce908877475a2@changeid
|
|
sparse complains on this code about casts that lose bits
due to the usage of bitwise not, but really we do want
16 bits only, so clarify that by using masks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223114023.c64e2d348453.Iccc4ace1116721a044e5f31f40ea7709e72145f3@changeid
|
|
The input parameter 'level' in rawv6_get/seticmpfilter is not used.
Therefore, remove it.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fast path usage breakdown describes the detail for 'inet_sock', fix
the markup title.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when suspending driver and stopping workqueue it is checked whether
workqueue is not NULL and if so, it is destroyed.
Function destroy_workqueue() does drain queue and does clear variable, but
it does not set workqueue variable to NULL. This can cause kernel/module
panic if code attempts to clear workqueue that was not initialized.
This scenario is possible when resuming suspended driver in stmmac_resume(),
because there is no handling for failed stmmac_hw_setup(),
which can fail and return if DMA engine has failed to initialize,
and workqueue is initialized after DMA engine.
Should DMA engine fail to initialize, resume will proceed normally,
but interface won't work and TX queue will eventually timeout,
causing 'Reset adapter' error.
This then does destroy workqueue during reset process.
And since workqueue is initialized after DMA engine and can be skipped,
it will cause kernel/module panic.
To secure against this possible crash, set workqueue variable to NULL when
destroying workqueue.
Log/backtrace from crash goes as follows:
[88.031977]------------[ cut here ]------------
[88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out
[88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398
<Skipping backtrace for watchdog timeout>
[88.032251]---[ end trace e70de432e4d5c2c0 ]---
[88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter.
[88.036359]------------[ cut here ]------------
[88.036519]Call trace:
[88.036523] flush_workqueue+0x3e4/0x430
[88.036528] drain_workqueue+0xc4/0x160
[88.036533] destroy_workqueue+0x40/0x270
[88.036537] stmmac_fpe_stop_wq+0x4c/0x70
[88.036541] stmmac_release+0x278/0x280
[88.036546] __dev_close_many+0xcc/0x158
[88.036551] dev_close_many+0xbc/0x190
[88.036555] dev_close.part.0+0x70/0xc0
[88.036560] dev_close+0x24/0x30
[88.036564] stmmac_service_task+0x110/0x140
[88.036569] process_one_work+0x1d8/0x4a0
[88.036573] worker_thread+0x54/0x408
[88.036578] kthread+0x164/0x170
[88.036583] ret_from_fork+0x10/0x20
[88.036588]---[ end trace e70de432e4d5c2c1 ]---
[88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
Fixes: 5a5586112b929 ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct type in the hsr_forward_do() comment.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updating link clock rate for different speeds is only needed when
using RGMII, as that mode requires changing clock speed when the link
speed changes. Let's restrict updating the link clock speed in
ethqos_update_link_clk() to just RGMII. Other modes such as SGMII
only need to enable the link clock (which is already done in probe).
Signed-off-by: Sarosh Hasan <quic_sarohasa@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Reviewed-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Justin Iurman says:
====================
ioam6: netlink multicast event
v5:
- remove the "must be the destination" check before sending an ioam6
event
v4:
- rebase on top of net merge
v3:
- patchset was mistakenly superseded due to same cover title used for
iproute2-next equivalent patch -> resend (renamed)
v2:
- fix warnings
Add generic netlink multicast event support to ioam6 as another solution
to share IOAM data with user space. The other one being via IPv6 raw
sockets combined with ancillary data (or packet socket, if the listener
does not need the processing of the IOAM Option-Type, since the hook is
before in that case). This patchset focuses on the IOAM Pre-allocated
Trace (the only Option-Type currently supported in the kernel), and so
on IOAM "trace" events. See an example of a consumer here [1].
[1] https://github.com/Advanced-Observability/ioam-agent-python/blob/netlink_event/ioam-agent.py
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we're processing an IOAM Pre-allocated Trace Option-Type (the only
one supported currently), then send the trace as an ioam6 event to the
netlink multicast group. This way, user space apps will be able to
collect IOAM data.
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a multicast group to the ioam6 generic netlink family and provide
ioam6_event() to send an ioam6 event to the multicast group.
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new api to support ioam6 events for generic netlink multicast. A
first "trace" event is added to the list of ioam6 events, which will
represent an IOAM Pre-allocated Trace Option-Type. It provides another
solution to share IOAM data with user space.
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dtschema defines label as string, so $ref in other bindings is
redundant.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a previous patch I added "select PHYLIB" at the wrong place for the
ADIN1110 driver symbol, so move it to its correct place under the
ADIN1110 kconfig symbol.
Fixes: a9f80df4f514 ("net: ethernet: adi: requires PHYLIB support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Closes: https://lore.kernel.org/lkml/77012b38-4b49-47f4-9a88-d773d52909ad@infradead.org/T/#m8ba397484738711edc0ad607b2c63ca02244e3c3
Cc: Lennart Franzen <lennart@lfdomain.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Cc: Nuno Sa <nuno.sa@analog.com>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
