| Age | Commit message (Collapse) | Author |
|---|
|
Add missed suspend/resume callbacks to properly restore networking after
suspend/resume cycle.
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Grygorii Strashko says:
====================
net: ethernet: ti: ale: add static configuration
As existing, as newly introduced CPSW ALE versions have differences in
supported features and ALE table formats. Especially it's actual for the
recent AM65x/J721E/J7200 and future AM64x SoCs, which supports more
features like: auto-aging, classifiers, Link aggregation, additional HW
filtering, etc.
The existing ALE configuration interface is not practical in terms of
adding new features and requires consumers to program a lot static
parameters. And any attempt to add new features will case endless adding
and maintaining different combination of flags and options. Because CPSW
ALE configuration is static and fixed for SoC (or set of SoC), It is
reasonable to add support for static ALE configurations inside ALE module.
This series introduces static ALE configuration table for different ALE
variants and provides option for consumers to select required ALE
configuration by providing ALE const char *dev_id identifier (Patch 2).
And all existing driver have been switched to use new approach (Patches 3-6).
After this ALE HW auto-ageing feature can be enabled for AM65x CPSW ALE
variant (Patch 7).
Finally, Patches 8-9 introduces tables to describe the ALE VLAN entries
fields as the ALE VLAN entries are too much differ between different TI
CPSW ALE versions. So, handling them using flags, defines and get/set
functions are became over-complicated.
Patch 1 - is preparation patch
Changes in v3:
- fixed comment for Patch 2
Changes in v2:
- fixed sparse warnings
v2: https://lore.kernel.org/patchwork/cover/1301684/
v1: https://lore.kernel.org/patchwork/cover/1301048/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TI J721E (CPSW9g) ALE version is similar, in general, to Sitara AM3/4/5
CPSW ALE, but has more extended functions and different ALE VLAN entry
format.
This patch adds support for for multi port TI J721E (CPSW9g) ALE variant.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ALE VLAN entries are too much differ between different TI CPSW ALE
versions. So, handling them using flags, defines and get/set functions
became over-complicated.
This patch introduces tables to describe the ALE VLAN entries fields, which
are different between TI CPSW ALE versions, and new get/set access
functions. It also allows to detect incorrect access to not available ALL
entry fields.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AM65x ALE supports HW auto-ageing which can be enabled by programming
ageing interval in ALE_AGING_TIMER register. For this CPSW fck_clk
frequency has to be know by ALE.
This patch extends cpsw_ale_params with bus_freq field and enables ALE HW
auto ageing for AM65x CPSW2G ALE version.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hence all existing driver updated to use ALE dev_id the usage of ale dev_id
can be made mandatory and cpsw_ale_create() can be updated to use
"features" property from ALE static configuration.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI TI AM65x/J721E CPSW NUSS driver to use
dev_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI Keystone 2 NETCP driver to use dev_id and
perform clean up by removing "ale_entries" configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI cpsw driver to use dev_id="cpsw" and
perform clean up by removing "ale_entries" configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As existing, as newly introduced CPSW ALE versions have differences in
supported features and ALE table formats. Especially it's actual for the
recent AM65x/J721E/J7200 SoC and feature AM64x, which supports features
like: auto-aging, classifiers, Link aggregation, additional hw filtering,
etc.
Existing ALE configuration interface is not practical in terms of adding
new features and requires consumers to program a lot static parameters. Any
attempt to add new options will case endless adding and maintaining
different combination of flags and options.
Hence CPSW ALE configuration is static and fixed for SoC (or set of SoC) It
is reasonable to add support for static ALE configurations inside ALE
module. This patch adds static ALE configuration table for different ALE
versions and provides option for consumers to select required ALE
configuration by providing ALE const char *dev_id identifier.
This feature is not enabled by default until existing CPSW drivers will be
modified by follow up patches.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add cpsw_ale_get_num_entries() API to return number of ALE table entries
and update existing drivers to use it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladimir Oltean says:
====================
DSA tag_8021q cleanup
This small series tries to consolidate the VLAN handling in DSA a little
bit. It reworks tag_8021q to be minimally invasive to the dsa_switch_ops
structure. This makes the rest of the code a bit easier to follow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 314f76d7a68bab0516aa52877944e6aacfa0fc3f.
Citing that commit message, the call graph was:
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Now that tag_8021q has its own ops structure, it no longer relies on
dsa_port_vid_add, and therefore on the dsa_switch_ops to install its
VLANs.
So dsa_port_vid_add now only has one single caller. So we can simplify
the call graph to what it was before, aka:
dsa_slave_vlan_rx_add_vid dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While working on another tag_8021q driver implementation, some things
became apparent:
- It is not mandatory for a DSA driver to offload the tag_8021q VLANs by
using the VLAN table per se. For example, it can add custom TCAM rules
that simply encapsulate RX traffic, and redirect & decapsulate rules
for TX traffic. For such a driver, it makes no sense to receive the
tag_8021q configuration through the same callback as it receives the
VLAN configuration from the bridge and the 8021q modules.
- Currently, sja1105 (the only tag_8021q user) sets a
priv->expect_dsa_8021q variable to distinguish between the bridge
calling, and tag_8021q calling. That can be improved, to say the
least.
- The crosschip bridging operations are, in fact, stateful already. The
list of crosschip_links must be kept by the caller and passed to the
relevant tag_8021q functions.
So it would be nice if the tag_8021q configuration was more
self-contained. This patch attempts to do that.
Create a struct dsa_8021q_context which encapsulates a struct
dsa_switch, and has 2 function pointers for adding and deleting a VLAN.
These will replace the previous channel to the driver, which was through
the .port_vlan_add and .port_vlan_del callbacks of dsa_switch_ops.
Also put the list of crosschip_links into this dsa_8021q_context.
Drivers that don't support cross-chip bridging can simply omit to
initialize this list, as long as they dont call any cross-chip function.
The sja1105_vlan_add and sja1105_vlan_del functions are refactored into
a smaller sja1105_vlan_add_one, which now has 2 entry points:
- sja1105_vlan_add, from struct dsa_switch_ops
- sja1105_dsa_8021q_vlan_add, from the tag_8021q ops
But even this change is fairly trivial. It just reflects the fact that
for sja1105, the VLANs from these 2 channels end up in the same hardware
table. However that is not necessarily true in the general sense (and
that's the reason for making this change).
The rest of the patch is mostly plain refactoring of "ds" -> "ctx". The
dsa_8021q_context structure needs to be propagated because adding a VLAN
is now done through the ops function pointers inside of it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no point in calling dsa_port_setup_8021q_tagging for each
individual port. Additionally, it will become more difficult to do that
when we'll have a context structure to tag_8021q (next patch). So
refactor this now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous assumption was that the caller would already have this
header file included.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like u32p_replace_bits() should be used instead of
u32_replace_bits() which does not modifies the value but returns the
modified version.
Fixes: 2b9feef2b6c2 ("soc: qcom: ipa: filter and routing tables")
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves complete nic tls offload (kTLS) code from crypto
directory to drivers/net/ethernet/chelsio/inline_crypto/ch_ktls
directory. nic TLS is made a separate ULD of cxgb4.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling hinic_close in hinic_set_channels, all queues are
stopped after netif_tx_disable, but some queue may be rewaken in
free_tx_poll by mistake while drv is handling tx irq. If one queue
is rewaken core may call hinic_xmit_frame to send pkt after
netif_tx_disable within a short time which may results in accessing
memory that has been already freed in hinic_close. So we call
napi_disable before netif_tx_disable in hinic_close to fix this bug.
Fixes: 2eed5a8b614b ("hinic: add set_channels ethtool_ops support")
Signed-off-by: Luo bin <luobin9@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's possible that the user specifies an interval that couldn't allow
any packet to be transmitted. This also avoids the issue of the
hrtimer handler starving the other threads because it's running too
often.
The solution is to reject interval sizes that according to the current
link speed wouldn't allow any packet to be transmitted.
Reported-by: syzbot+8267241609ae8c23b248@syzkaller.appspotmail.com
Fixes: 5a781ccbd19e ("tc: Add support for configuring the taprio scheduler")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-09-09
This series contains updates to i40e and igc drivers.
Stefan Assmann changes num_vlans to u16 to fix may be used uninitialized
error and propagates error in i40_set_vsi_promisc() for i40e.
Vinicius corrects timestamping latency values for i225 devices and
accounts for TX timestamping delay for igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Edward Cree says:
====================
sfc: encap offloads on EF10
EF10 NICs from the 8000 series onwards support TX offloads (checksumming,
TSO) on VXLAN- and NVGRE-encapsulated packets. This series adds driver
support for these offloads.
Changes from v1:
* Fix 'no TXQ of type' error handling in patch #1 (and clear up the
misleading comment that inspired the wrong version)
* Add comment in patch #5 explaining what the deal with TSOv3 is
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Necessitates an .ndo_features_check, as the EF10 datapath has several
limitations on what it can handle.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From the 8000 series onwards, EF10 NICs with suitable firmware are able
to perform TSO within VXLAN or NVGRE encapsulation.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the tx_queue->handle_tso function pointer, and just use
tx_queue->tso_version to decide which function to call, thus removing
an indirect call from the fast path.
Instead of passing a tso_v2 flag to efx_mcdi_tx_init(), set the desired
tx_queue->tso_version before calling it.
In efx_mcdi_tx_init(), report back failure to obtain a TSOv2 context by
setting tx_queue->tso_version to 0, which will cause the TX path to
use the GSO-based fallback.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Won't actually be exercised until we start advertising the corresponding
offload features.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the MC reports the VXLAN_NVGRE datapath capability, then these queues
can be used for checksum offload of encapsulated packets.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nothing yet creates inner csum TXQs; just change all references to
EFX_TXQ_TYPE_OFFLOAD to the new EFX_TXQ_TYPE_OUTER_CSUM.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make it possible to have an arbitrary mapping from types to labels,
because when we add inner-csum-offload TXQs there will no longer be a
convenient nesting hierarchy of NIC types (EF10 will have inner-csum
TXQs, while Siena will have HIGHPRI).
Correct a misleading comment on efx_hard_start_xmit().
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are never modified, so constify them to allow the compiler to
place them in read-only memory. This moves about 25kB to read-only
memory as seen by the output of the size command.
Before:
text data bss dec hex filename
296203 65464 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko
After:
text data bss dec hex filename
321003 40664 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Edward Cree says:
====================
sfc: misc cleanups
Clean up a few nits I noticed while working on TXQ stuff.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The old_channel argument is never used, so remove it.
The function is only called from elsewhere in efx_channels.c, so make
it static and remove the declaration from the header file.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The statement above it already returns, so there is no way to get here.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
efx_init_struct already calls this, we don't need to do it again.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each MDB entry is encoded in a nested netlink attribute called
'MDBA_MDB_ENTRY'. In turn, this attribute contains another nested
attributed called 'MDBA_MDB_ENTRY_INFO', which encodes a single port
group entry within the MDB entry.
The cited commit added the ability to restart a dump from a specific
port group entry. However, on failure to add a port group entry to the
dump the entire MDB entry (stored in 'nest2') is removed, resulting in
missing port group entries.
Fix this by finalizing the MDB entry with the partial list of already
encoded port group entries.
Fixes: 5205e919c9f0 ("net: bridge: mcast: add support for src list and filter mode dumping")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable err is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is redundant
and can be removed. Also re-order variable declarations in reverse
Christmas tree ordering.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the correct resolution for the conflict from
merging the "net" tree fix:
commit 26cb7085c898 ("enetc: Remove the mdio bus on PF probe bailout")
with the "net-next" new work:
commit 07095c025ac2 ("net: enetc: Use DT protocol information to set up the ports")
that moved mdio bus allocation to an ealier stage of
the PF probing routine.
Fixes: a57066b1a019 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Oleksij Rempel says:
====================
ag71xx: add ethtool and flow control support
The main target of this patches is to provide flow control support
for ag71xx driver. To be able to validate this functionality, I also
added ethtool support with HW counters. So, this patches was validated
with iperf3 and counters showing Pause frames send or received by this
NIC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add flow control support. The functionality was tested on AR9331 SoC and
confirmed by iperf3 results and HW counters exported over ethtool.
Following test configurations was used:
iMX6S receiver <--- TL-SG1005D switch <---- AR9331 sender
The switch is supporting symmytric flow control:
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
--->> Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: on
Port: MII
PHYAD: 4
Transceiver: external
Link detected: yes
The iMX6S system was configured to 10Mbit, to let the switch use flow
control:
- ethtool -s eth0 speed 10
With flow control disabled on AR9331:
- ethtool -A eth0 rx off tx off
- iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 66.2 MBytes 55.5 Mbits/sec 0.000 ms 0/47155 (0%) sender
[ 5] 0.00-10.04 sec 11.5 MBytes 9.57 Mbits/sec 1.309 ms 38986/47146 (83%) receiver
With flow control enabled on AR9331:
- ethtool -A eth0 rx on tx on
- iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 15.1 MBytes 12.6 Mbits/sec 0.000 ms 0/10727 (0%) sender
[ 5] 0.00-10.05 sec 11.5 MBytes 9.57 Mbits/sec 1.371 ms 2525/10689 (24%) receiver
Similar results are get in opposite direction by introducing extra CPU
load on AR9331:
- chrt 40 dd if=/dev/zero of=/dev/null &
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic ethtool support. The functionality was tested on AR9331 SoC.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "SLF_OUTWAIT" flag defined in x25_asy.h is not actually used.
It is only cleared at one place in x25_asy.c but is never read or set.
So we can remove it.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
code to return
We found the following warning when using W=1 to build kernel:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret, coe = priv->hw->rx_csum;
When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and
dwxgmac2_get_rx_header_len() return 0 only, without any error code to
report. Therefore, it's better to define get_rx_header_len() as void.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Awogbemila says:
====================
Add GVE Features.
Note: Patch 4 in v3 was dropped.
Patch 4 (patch 5 in v3): Start/stop timer only when report stats is
enabled/disabled.
Patch 7 (patch 8 in v3): Use netdev_info, not dev_info, to log
device link status.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change allows the driver to report the device link speed
when the ethtool command:
ethtool <nic name>
is run.
Getting the link speed is done via a new admin queue command:
ReportLinkSpeed.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes the driver better aware of the connectivity status of the
device. Based on the device's status register, the driver can call
netif_carrier_{on,off}.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Patricio Noyola <patricion@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for batching AQ commands and uses it for creating and
destroying queues.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds per queue NIC stats to ethtool stats and to report-stats.
These stats are always exposed to guest whether or not the
report-stats flag is turned on.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds functionality to report driver stats to Hypervisor.
(Users may want to turn this feature off as a matter of privacy
so a "report-stats" flag is added as an ethtool priv option.
It is also disabled by default.)
The hypervisor would trigger a stats report in case "too many"
packets dropped; the stats would be useful in debugging stuck
queues.
A "stats_report_trigger_cnt" stat is added to count the number of times
the hypervisor attempts to trigger stats report.
A timer is also added so that when report-stats is enabled, stat are
updated once every 20 seconds.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Kuo Zhao <kuozhao@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the driver to use dev_info/err instead of netif_info/err.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sample output of "ethtool -S <interface-name>" with 1 RX queue and 1 TX
queue:
NIC statistics:
rx_packets: 1039
tx_packets: 37
rx_bytes: 822071
tx_bytes: 4100
rx_dropped: 0
tx_dropped: 0
tx_timeouts: 0
rx_skb_alloc_fail: 0
rx_buf_alloc_fail: 0
rx_desc_err_dropped_pkt: 0
interface_up_cnt: 1
interface_down_cnt: 0
reset_cnt: 0
page_alloc_fail: 0
dma_mapping_error: 0
rx_posted_desc[0]: 1365
rx_completed_desc[0]: 341
rx_bytes[0]: 215094
rx_dropped_pkt[0]: 0
rx_copybreak_pkt[0]: 3
rx_copied_pkt[0]: 3
tx_posted_desc[0]: 6
tx_completed_desc[0]: 6
tx_bytes[0]: 420
tx_wake[0]: 0
tx_stop[0]: 0
tx_event_counter[0]: 6
adminq_prod_cnt: 34
adminq_cmd_fail: 0
adminq_timeouts: 0
adminq_describe_device_cnt: 1
adminq_cfg_device_resources_cnt: 1
adminq_register_page_list_cnt: 16
adminq_unregister_page_list_cnt: 0
adminq_create_tx_queue_cnt: 8
adminq_create_rx_queue_cnt: 8
adminq_destroy_tx_queue_cnt: 0
adminq_destroy_rx_queue_cnt: 0
adminq_dcfg_device_resources_cnt: 0
adminq_set_driver_parameter_cnt: 0
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Kuo Zhao <kuozhao@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
