| Age | Commit message (Collapse) | Author |
|---|
|
Implement tcpc.enable_frs to enable TCPC to receive
Fast role swap signal.
Additionally set the sink disconnect threshold to 4v
to prevent disconnect during Fast Role swap.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-8-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.
Once the explicit contract is negotiated, sink port is
expected to query the source port for sink caps to
determine whether the source is FRS capable.
Bits 23 & 24 of fixed pdo of the sink caps from the source, when
set, indicates the current needed by the source when fast role
swap is in progress(Implicit contract phasae). 0 indicates that
the source does not support Fast Role Swap.
Upon receiving the FRS signal from the source,
TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.
1. TCPM sends FRS PD message: FR_SWAP_SEND
2. If response is not received within the expiry of
SenderResponseTimer, Error recovery is triggered.:
FR_SWAP_SEND_TIMEOUT
3. Upon receipt of the accept message, TCPM waits for
PSSourceOffTimer for PS_READY message from the partner:
FR_SWAP_SNK_SRC_NEW_SINK_READY.
TCPC is expected to autonomously turn on vbus once the FRS
signal is received and vbus voltage falls below vsafe5v within
tSrcFrSwap. This is different from traditional power role swap
where the vbus sourcing is turned on by TCPM.
4. By this time, TCPC most likely would have started to
source vbus, TCPM waits for tSrcFrSwap to see if the
lower level TCPC driver signals TCPM_SOURCING_VBUS event:
FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
changes the CC pin from Rd to Rp. This is the end of fast
role swap sequence and TCPM initiates the sequnce to negotiate
explicit contract by transitioning into SRC_STARTUP after
SwapSrcStart.
The code is written based on the sequence described in "Figure 8-107:
Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
USB Power Delivery Specification Revision 3.0, Version 1.2.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-7-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Chip level TCPC driver for Maxim's TCPCI implementation.
This TCPC implementation does not support the following
commands: COMMAND.SinkVbus, COMMAND.SourceVbusDefaultVoltage,
COMMAND.SourceVbusHighVoltage. Instead the sinking and sourcing
from vbus is supported by writes to custom registers.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-5-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
set_vbus callback allows TCPC which are TCPCI based, however,
does not support turning on sink and source mode through
Command.SinkVbus and Command.SourceVbusDefaultVoltage.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow chip level drivers to retrieve reference to tcpm_port.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kcov testing uncovered call to usb_hcd_giveback_urb() without disabling
interrupts.
Link: https://lore.kernel.org/linux-usb/CAAeHK+wb4k-LGTjK9F5YbJNviF_+yU+wE_=Vpo9Rn7KFN8vG6Q@mail.gmail.com/
usb_hcd_giveback_urb() is called from vhci's urb_enqueue, when it
determines it doesn't need to xmit the urb and can give it back.
This path runs in task context.
Disable irqs around usb_hcd_giveback_urb() call.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201006223914.39257-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ES58X devices has a CDC ACM interface (used for debug
purpose). During probing, the device is thus recognized as USB Modem
(CDC ACM), preventing the etas-es58x module to load:
usbcore: registered new interface driver etas_es58x
usb 1-1.1: new full-speed USB device number 14 using xhci_hcd
usb 1-1.1: New USB device found, idVendor=108c, idProduct=0159, bcdDevice= 1.00
usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.1: Product: ES581.4
usb 1-1.1: Manufacturer: ETAS GmbH
usb 1-1.1: SerialNumber: 2204355
cdc_acm 1-1.1:1.0: No union descriptor, testing for castrated device
cdc_acm 1-1.1:1.0: ttyACM0: USB ACM device
Thus, these have been added to the ignore list in
drivers/usb/class/cdc-acm.c
N.B. Future firmware release of the ES58X will remove the CDC-ACM
interface.
`lsusb -v` of the three devices variant (ES581.4, ES582.1 and
ES584.1):
Bus 001 Device 011: ID 108c:0159 Robert Bosch GmbH ES581.4
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0159
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES581.4
iSerial 3 2204355
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0035
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 5 Bus Powered Configuration
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 4 ACM Control Interface
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x01
call management
bDataInterface 0
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 10
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 012: ID 108c:0168 Robert Bosch GmbH ES582
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0168
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES582
iSerial 3 0108933
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 013: ID 108c:0169 Robert Bosch GmbH ES584.1
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0169
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES584.1
iSerial 3 0100320
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201002154219.4887-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
Pull kvm fixes from Paolo Bonzini:
"Two bugfixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: update PFEC_MASK/PFEC_MATCH together with PF intercept
KVM: arm64: Restore missing ISB on nVHE __tlb_switch_to_guest
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"Fix a regression introduced in 5.9-rc3 which caused a system running
as fully virtualized guest under Xen to crash when using legacy
devices like a floppy"
* tag 'for-linus-5.9b-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: don't use chip_data for legacy IRQs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are some small USB and PHY driver fixes for 5.9-rc8
The PHY driver fix resolves an issue found by Dan Carpenter for a
memory leak.
The USB fixes fall into two groups:
- usb gadget fix from Bryan that is a fix for a previous security fix
that showed up in in-the-wild testing
- usb core driver matching bugfixes. This fixes a bug that has
plagued the both the usbip driver and syzbot testing tools this -rc
release cycle. All is now working properly so usbip connections
will work, and syzbot can get back to fuzzing USB drivers properly.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usbcore/driver: Accommodate usbip
usbcore/driver: Fix incorrect downcast
usbcore/driver: Fix specific driver selection
Revert "usbip: Implement a match function to fix usbip"
USB: gadget: f_ncm: Fix NDP16 datagram validation
phy: ti: am654: Fix a leak in serdes_am654_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some more driver fixes for i2c"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: npcm7xx: Clear LAST bit after a failed transaction.
i2c: cpm: Fix i2c_ram structure
i2c: i801: Exclude device from suspend direct complete optimization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A couple more driver quirks, now enabling newer trackpoints from
Synaptics for real"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add nopnp quirk for Acer Aspire 5 A515
Input: trackpoint - enable Synaptics trackpoints
|
|
One of the entries has three fields "mistake||correction||correction"
rather than the expected two fields "mistake||correction". Fix it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/20200930234359.255295-1-ebiggers@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
memalloc_nocma_{save/restore} APIs can be used to skip page allocation
on CMA area, but, there is a missing case and the page on CMA area could
be allocated even if APIs are used. This patch handles this case to fix
the potential issue.
For now, these APIs are used to prevent long-term pinning on the CMA
page. When the long-term pinning is requested on the CMA page, it is
migrated to the non-CMA page before pinning. This non-CMA page is
allocated by using memalloc_nocma_{save/restore} APIs. If APIs doesn't
work as intended, the CMA page is allocated and it is pinned for a long
time. This long-term pin for the CMA page causes cma_alloc() failure
and it could result in wrong behaviour on the device driver who uses the
cma_alloc().
Missing case is an allocation from the pcplist. MIGRATE_MOVABLE pcplist
could have the pages on CMA area so we need to skip it if ALLOC_CMA
isn't specified.
Fixes: 8510e69c8efe (mm/page_alloc: fix memalloc_nocma_{save/restore} APIs)
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Link: https://lkml.kernel.org/r/1601429472-12599-1-git-send-email-iamjoonsoo.kim@lge.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The routine that applies debug flags to the kmem_cache slabs
inadvertantly prevents non-debug flags from being applied to those
same objects. That is, if slub_debug=<flag>,<slab> is specified,
non-debugged slabs will end up having flags of zero, and the slabs
may be unusable.
Fix this by including the input flags for non-matching slabs with the
contents of slub_debug, so that the caches are created as expected
alongside any debugging options that may be requested. With this, we
can remove the check for a NULL slub_debug_string, since it's covered
by the loop itself.
Fixes: e17f1dfba37b ("mm, slub: extend slub_debug syntax for multiple blocks")
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Kees Cook <keescook@chromium.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Link: https://lkml.kernel.org/r/20200930161931.28575-1-farman@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.10 merge window
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
usb: dwc2: override PHY input signals with usb role switch support
dt-bindings: usb: dwc2: add optional usb-role-switch property
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
usb: dwc3: gadget: Support up to max stream id
usb: dwc3: gadget: Return early if no TRB update
usb: dwc3: gadget: Keep TRBs in request order
usb: dwc3: gadget: Revise setting IOC when no TRB left
usb: dwc3: gadget: Look ahead when setting IOC
usb: dwc3: gadget: Allow restarting a transfer
usb: bdc: remove duplicated error message
usb: dwc3: Stop active transfers before halting the controller
usb: cdns3: gadget: enlarge the TRB ring length
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
usb: cdns3: gadget: need to handle sg case for workaround 2 case
usb: cdns3: gadget: handle sg list use case at completion correctly
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/arm64 fixes for 5.9, take #3
- Fix synchronization of VTTBR update on TLB invalidation for nVHE systems
|
|
The PFEC_MASK and PFEC_MATCH fields in the VMCS reverse the meaning of
the #PF intercept bit in the exception bitmap when they do not match.
This means that, if PFEC_MASK and/or PFEC_MATCH are set, the
hypervisor can get a vmexit for #PF exceptions even when the
corresponding bit is clear in the exception bitmap.
This is unexpected and is promptly detected by a WARN_ON_ONCE.
To fix it, reset PFEC_MASK and PFEC_MATCH when the #PF intercept
is disabled (as is common with enable_ept && !allow_smaller_maxphyaddr).
Reported-by: Qian Cai <cai@redhat.com>>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some pin control fixes here. All of them are driver fixes, the Intel
Cherryview being the most interesting one.
- Fix a mux problem for I2C in the MVEBU driver.
- Fix a really hairy inversion problem in the Intel Cherryview
driver.
- Fix the register for the sdc2_clk in the Qualcomm SM8250 driver.
- Check the virtual GPIO boot failur in the Mediatek driver"
* tag 'pinctrl-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: check mtk_is_virt_gpio input parameter
pinctrl: qcom: sm8250: correct sdc2_clk
pinctrl: cherryview: Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
pinctrl: mvebu: Fix i2c sda definition for 98DX3236
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix rockchip regression in rockchip_pcie_valid_device() (Lorenzo
Pieralisi)
- Add Pali Rohár as aardvark PCI maintainer (Pali Rohár)
* tag 'pci-v5.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add Pali Rohár as aardvark PCI maintainer
PCI: rockchip: Fix bus checks in rockchip_pcie_valid_device()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two patches in driver frameworks. The iscsi one corrects a bug induced
by a BPF change to network locking and the other is a regression we
introduced"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: iscsi_tcp: Avoid holding spinlock while calling getpeername()
scsi: target: Fix lun lookup for TARGET_SCF_LOOKUP_LUN_FROM_TAG case
|
|
Pull io_uring fixes from Jens Axboe:
- fix for async buffered reads if read-ahead is fully disabled (Hao)
- double poll match fix
- ->show_fdinfo() potential ABBA deadlock complaint fix
* tag 'io_uring-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
io_uring: fix async buffered reads when readahead is disabled
io_uring: fix potential ABBA deadlock in ->show_fdinfo()
io_uring: always delete double poll wait entry on match
|
|
Pull block fix from Jens Axboe:
"Single fix for a ->commit_rqs failure case"
* tag 'block-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
blk-mq: call commit_rqs while list empty but error happen
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull epoll fixes from Al Viro:
"Several race fixes in epoll"
* 'work.epoll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ep_create_wakeup_source(): dentry name can change under you...
epoll: EPOLL_CTL_ADD: close the race in decision to take fast path
epoll: replace ->visited/visited_list with generation count
epoll: do not insert into poll queues until all sanity checks are done
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"Two fixes for this week:
- The addition of a symbol export for clint_time_val, which has been
inlined into some timex functions and can be used by drivers.
- A fix to avoid calling get_cycles() before the timers have been
probed.
These both only effect !MMU systems"
* tag 'riscv-for-linus-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Check clint_time_val before use
clocksource: clint: Export clint_time_val for modules
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Two more fixes.
One is for a lockdep warning/lockup (also caught by syzbot), that one
has been seen in practice. Regarding the other syzbot reports
mentioned last time, they don't seem to be urgent and reliably
reproducible so they'll be fixed later.
The second fix is for a potential corruption when device replace
finishes and the in-memory state of trim is not copied to the new
device"
* tag 'for-5.9-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix filesystem corruption after a device replace
btrfs: move btrfs_rm_dev_replace_free_srcdev outside of all locks
btrfs: move btrfs_scratch_superblocks into btrfs_dev_replace_finishing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix one more issue related to the recent RCU-lockdep changes, a
typo in documentation and add a missing return statement to
intel_pstate.
Specifics:
- Fix up RCU usage for cpuidle on the ARM imx6q platform (Ulf
Hansson)
- Fix typo in the PM documentation (Yoann Congal)
- Add return statement that is missing after recent changes in the
intel_pstate driver (Zhang Rui)"
* tag 'pm-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: imx6q: Fixup RCU usage for cpuidle
Documentation: PM: Fix a reStructuredText syntax error
cpufreq: intel_pstate: Fix missing return statement
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are two small IIO driver fixes for 5.9-rc8 that resolve some
reported issues:
- driver name fixed in one driver
- device name typo fixed
Both have been in linux-next for a while with no reported problems"
* tag 'staging-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: qcom-spmi-adc5: fix driver name
iio: adc: ad7124: Fix typo in device name
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Fix deadlock when removing MEMSTICK host
- Workaround broken CMDQ on Intel GLK based IRBIS models
* tag 'mmc-v5.9-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci: Workaround broken command queuing on Intel GLK based IRBIS models
memstick: Skip allocating card when removing host
|
|
Commit f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") broke compilation and was temporarily fixed by Linus in
83bdc7275e62 ("random32: remove net_rand_state from the latent entropy
gcc plugin") by entirely moving net_rand_state out of the things handled
by the latent_entropy GCC plugin.
From what I understand when reading the plugin code, using the
__latent_entropy attribute on a declaration was the wrong part and
simply keeping the __latent_entropy attribute on the variable definition
was the correct fix.
Fixes: 83bdc7275e62 ("random32: remove net_rand_state from the latent entropy gcc plugin")
Acked-by: Willy Tarreau <w@1wt.eu>
Cc: Emese Revfy <re.emese@gmail.com>
Signed-off-by: Thibaut Sautereau <thibaut.sautereau@ssi.gouv.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* pm-cpufreq:
cpufreq: intel_pstate: Fix missing return statement
|
|
Since commit ea426c2a7de8 ("mm: memcg: prepare for byte-sized vmstat
items") the write side of slab counters accepts a value in bytes and
converts it to pages. It happens in __mod_node_page_state().
However a non-SMP version of __mod_node_page_state() doesn't perform
this conversion. It leads to incorrect (unrealistically high) slab
counters values. Fix this by adding a similar conversion to the non-SMP
version of __mod_node_page_state().
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-and-tested-by: Bastian Bittorf <bb@npl.de>
Fixes: ea426c2a7de8 ("mm: memcg: prepare for byte-sized vmstat items")
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The latest reference to usbfs_conn_disc_event() removed in
commit fb28d58b72aa ("USB: remove CONFIG_USB_DEVICEFS")
in 2012 and now a user poll() waits infinitely for content changes.
Signed-off-by: Sergey Korolev <s.korolev@ndmsystems.com>
Link: https://lore.kernel.org/r/20200809161233.13135-1-s.korolev@ndmsystems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
STMicroelectronics USB Type-C port controllers use I2C interface to
configure, control and read the operation status of the device. All ST USB
Type-C port controllers are based on the same I2C register map. That's why
this driver can be used with all ST USB Type-C ICs.
Some ST USB Type-C port controllers are Dual Role Port (DRP), only Sink or
Source, some supports USB Power Delivery. This can be configured through
connector device tree bindings.
This driver is a basic Type-C port controller driver, with no power
delivery support. It allows to configure ST USB Type-C port controller.
Interrupt is supported and enables CC connection events, to detect
attach and detach and update Type-C subsystem accordingly as well as usb
role switch.
ST USB Type-C port controller can be supplied in three different ways
depending on the target application:
- through VDD pin only (so VDD is the main supply)
- through VSYS pin only (so VSYS is the main supply)
- through VDD and VSYS pins.
When both VDD and VSYS power supplies are present, the low power supply
VSYS is selected as main supply when VSYS voltage is above 3.1V, else
VDD is selected as main supply.
In case of Source or Dual port type, if VDD supply is present, it has to be
enabled in case of Source power role to provide Vbus. When interrupt
support is available, VDD supply is dynamically managed upon attach/detach
interrupt. When there is no interrupt support, VDD supply is enabled by
default.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-5-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a function that converts power operation mode string into
power operation mode value.
It is useful to configure power operation mode through device tree
property, as power capabilities may be linked to hardware design.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-3-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some platforms have only super speed data bus connected to this device
and high speed data bus directly connected to the SoC. In such platforms
modelling connector as a child of this device is making it non compliant
with usb connector bindings. By modelling connector node as standalone
device node along with this device and the SoC data bus will make it
compliant with usb connector bindings.
Update the driver to handle this model by using OF graph API to get the
connector fwnode and usb role switch class API to get role switch handle.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200920134905.4370-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Document HS and SS data bus for the "usb-role-switch" enabled case.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200920134905.4370-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert ti,hd3ss3220.txt to YAML. Updated the binding documentation
as graph bindings of this device model Super Speed (SS) data bus to
the Super Speed (SS) capable connector.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200920134905.4370-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into usb-next
Vinod writes:
phy for 5.9
- Core:
- New PHY attribute for max_link_rate
- New phy drivers:
- Rockchip dphy driver moved from staging
- Socionext UniPhier AHCI PHY driver
- Intel LGM SoC USB phy
- Intel Keem Bay eMMC PHY driver
- Updates:
- Support for imx8mp usb phy
- Support for DP Phy and USB3+DP combo phy in QMP driver
- Support for Qualcomm sc7180 DP phy
- Support for cadence torrent PCIe and USB single linke and multilink
configurations along with USB, SGMII/QSGMII configurations
* tag 'phy-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
phy: qcom-qmp: initialize the pointer to NULL
phy: qcom-qmp: Add support for sc7180 DP phy
phy: qcom-qmp: Add support for DP in USB3+DP combo phy
phy: qcom-qmp: Use devm_platform_ioremap_resource() to simplify
phy: qcom-qmp: Get dp_com I/O resource by index
phy: qcom-qmp: Move 'serdes' and 'cfg' into 'struct qcom_phy'
phy: qcom-qmp: Remove 'initialized' in favor of 'init_count'
phy: qcom-qmp: Move phy mode into struct qmp_phy
dt-bindings: phy: qcom,qmp-usb3-dp: Add DP phy information
dt-bindings: phy: ti,phy-j721e-wiz: fix bindings for torrent phy
dt-bindings: phy: cdns,torrent-phy: add reset-names
phy: rockchip-dphy-rx0: Include linux/delay.h
phy: fix USB_LGM_PHY warning & build errors
phy: cadence-torrent: Add USB + SGMII/QSGMII multilink configuration
phy: cadence-torrent: Add PCIe + USB multilink configuration
phy: cadence-torrent: Add single link USB register sequences
phy: cadence-torrent: Add single link SGMII/QSGMII register sequences
phy: cadence-torrent: Configure PHY_PLL_CFG as part of link_cmn_vals
phy: cadence-torrent: Add PHY link configuration sequences for single link
phy: cadence-torrent: Add clk changes for multilink configuration
...
|
|
In DDMA mode if INTR OUT transfers mps not multiple of 4 then single packet
corresponds to single descriptor.
Descriptor limit set to mps and desc chain limit set to mps *
MAX_DMA_DESC_NUM_GENERIC. On that descriptors complete, to calculate
transfer size should be considered correction value for each descriptor.
In start request function, if "continue" is true then dma buffer address
should be incremmented by offset for all type of transfers, not only for
Control DATA_OUT transfers.
Fixes: cf77b5fb9b394 ("usb: dwc2: gadget: Transfer length limit checking for DDMA")
Fixes: e02f9aa6119e0 ("usb: dwc2: gadget: EP 0 specific DDMA programming")
Fixes: aa3e8bc81311e ("usb: dwc2: gadget: DDMA transfer start and complete")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
If usb-role-switch is present in the device tree, it means that ID and Vbus
signals are not connected to the OTG controller but to an external
component (GPIOs, Type-C controller). In this configuration, usb role
switch is used to force valid sessions on STM32MP15 SoCs.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
This patch adds support for usb role switch to dwc2, by using overriding
control of the PHY voltage valid and ID input signals.
iddig signal (ID) can be overridden:
- when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1;
- when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0.
avalid/bvalid/vbusvalid signals can be overridden respectively with:
- GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL
- GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL
- GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL
It is possible to determine valid sessions thanks to usb role switch:
- if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid
- if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid
- if USB_ROLE_HOST then avalid && !bvalid && vbusvalid
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
This patch documents the usb-role-switch property in dwc2 bindings, now
that usb-role-switch support is available in dwc2 driver.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Add compatible string to use this generic glue layer to support
Intel Keem Bay platform's dwc3 controller.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
Binding description for Intel Keem Bay USB controller.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
DWC3 IPs can use the maximum stream id (up to 2^16) specified by the
USB 3.x specs. Don't limit to stream id 2^15 only. Note that this does
not reflect the number of concurrent streams the controller handles
internally.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
[1] https://syzkaller.appspot.com/bug?id=e7b761593b23eb50855b9ea31e3be5472b711186
[2] https://lkml.kernel.org/r/27b7545e-8f41-10b8-7c02-e35a08eb1611@i-love.sakura.ne.jp
[3] https://lkml.kernel.org/r/79ba410f-e0ef-2465-b94f-6b9a4a82adf5@i-love.sakura.ne.jp
[4] https://lkml.kernel.org/r/20200530011040.GB12419@rowland.harvard.edu
[5] https://lkml.kernel.org/r/c85331fc-874c-6e46-a77f-0ef1dc075308@i-love.sakura.ne.jp
Reported-by: syzbot <syzbot+854768b99f19e89d7f81@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928141755.3476-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
