| Age | Commit message (Collapse) | Author |
|---|
|
There are specific ACPI and I\xB2C APIs to match device by different
parameters, such as ACPI HID, and retrieve an I\xB2C client.
Use them instead of home grown approach.
Note, it fixes a resource leak as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
IOSF MBI header contains a lot of definitions, such as
end point addresses of IPs. Move CCK address from AtomISP driver
to generic header.
While here, drop unused one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Intel MID special header is not in use in this driver.
Replace it with a better macro for now on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Instead of parsing GPIO for two exceptions inside the logic
which would be trying to use the GPIO, move the init code
to the routine which adds a new gmin device.
Move the notes to it too, as this helps to identify where
those two GPIO settings are used, explaining why they're
defaulting to -1 when not found.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There's only one place where a subdev can be added: when the
sensor driver registers it. Trying to do it elsewhere will
cause problems, as the detection code needs to access the
I2C bus in order to probe some things.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If the ACPI DSDT tables provide _CRS for the camera, the
GPIO core code should be able to handle them automatically.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The media core has now a check if fi->pad is bigger than zero
or bigger than sd->entity.num_pads, if the media controller
is defined.
This causes a call to g_frame_interval to return -EINVAL.
Fix it by first cleaning up the struct.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Newer devices don't place the PMIC CLK line inside an EFI
var. Instead, those are found at the _PR0 table.
Add a parser for it, using info stored via the DSDT table.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support code for this driver to use ACPI power management.
Yet, at least with known devices, this won't work without
further changes.
The rationale is that the ACPI handling code checks for the _PR? tables
in order to know what is required to switch the device from power state
D0 (_PR0) up to D3COLD (_PR3).
The adev->flags.power_manageable is set to true if the device has a _PR0
table, which can be checked by calling acpi_device_power_manageable(adev).
However, this only says that the device can be set to power off mode.
At least on the DSDT tables we've seen so far, there's no _PR3 nor _PS3
(which would have a somewhat similar effect).
So, using ACPI for power management won't work, except if adding
an ACPI override logic somewhere.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The gmin_subdev_add() currently doesn't use ACPI device
power management. In order to prepare for adding support
for it, let's shift some things, placing the PM-related
stuff at the end of the probing logic.
Let's also store the current gs on a temporary var, in
order to simplify the source code.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Jakub Sitnicki says:
====================
Changelog
=========
v4 -> v5:
- Enforce BPF prog return value to be SK_DROP or SK_PASS. (Andrii)
- Simplify prog runners now that only SK_DROP/PASS can be returned.
- Enable bpf_perf_event_output from the start. (Andrii)
- Drop patch
"selftests/bpf: Rename test_sk_lookup_kern.c to test_ref_track_kern.c"
- Remove tests for narrow loads from context at an offset wider in size
than target field, while we are discussing how to fix it:
https://lore.kernel.org/bpf/20200710173123.427983-1-jakub@cloudflare.com/
- Rebase onto recent bpf-next (bfdfa51702de)
- Other minor changes called out in per-patch changelogs,
see patches: 2, 4, 6, 13-15
- Carried over Andrii's Acks where nothing changed.
v3 -> v4:
- Reduce BPF prog return codes to SK_DROP/SK_PASS (Lorenz)
- Default to drop on illegal return value from BPF prog (Lorenz)
- Extend bpf_sk_assign to accept NULL socket pointer.
- Switch to saner return values and add docs for new prog_array API (Andrii)
- Add support for narrow loads from BPF context fields (Yonghong)
- Fix broken build when IPv6 is compiled as a module (kernel test robot)
- Fix null/wild-ptr-deref on BPF context access
- Rebase to recent bpf-next (eef8a42d6ce0)
- Other minor changes called out in per-patch changelogs,
see patches 1-2, 4, 6, 8, 10-12, 14, 16
v2 -> v3:
- Switch to link-based program attachment
- Support for multi-prog attachment
- Ability to skip reuseport socket selection
- Code on RX path is guarded by a static key
- struct in6_addr's are no longer copied into BPF prog context
- BPF prog context is initialized as late as possible
- Changes called out in patches 1-2, 4, 6, 8, 10-14, 16
- Patches dropped:
01/17 flow_dissector: Extract attach/detach/query helpers
03/17 inet: Store layer 4 protocol in inet_hashinfo
08/17 udp: Store layer 4 protocol in udp_table
v1 -> v2:
- Changes called out in patches 2, 13-15, 17
- Rebase to recent bpf-next (b4563facdcae)
RFCv2 -> v1:
- Switch to fetching a socket from a map and selecting a socket with
bpf_sk_assign, instead of having a dedicated helper that does both.
- Run reuseport logic on sockets selected by BPF sk_lookup.
- Allow BPF sk_lookup to fail the lookup with no match.
- Go back to having just 2 hash table lookups in UDP.
RFCv1 -> RFCv2:
- Make socket lookup redirection map-based. BPF program now uses a
dedicated helper and a SOCKARRAY map to select the socket to redirect to.
A consequence of this change is that bpf_inet_lookup context is now
read-only.
- Look for connected UDP sockets before allowing redirection from BPF.
This makes connected UDP socket work as expected in the presence of
inet_lookup prog.
- Share the code for BPF_PROG_{ATTACH,DETACH,QUERY} with flow_dissector,
the only other per-netns BPF prog type.
Overview
========
This series proposes a new BPF program type named BPF_PROG_TYPE_SK_LOOKUP,
or BPF sk_lookup for short.
BPF sk_lookup program runs when transport layer is looking up a listening
socket for a new connection request (TCP), or when looking up an
unconnected socket for a packet (UDP).
This serves as a mechanism to overcome the limits of what bind() API allows
to express. Two use-cases driving this work are:
(1) steer packets destined to an IP range, fixed port to a single socket
192.0.2.0/24, port 80 -> NGINX socket
(2) steer packets destined to an IP address, any port to a single socket
198.51.100.1, any port -> L7 proxy socket
In its context, program receives information about the packet that
triggered the socket lookup. Namely IP version, L4 protocol identifier, and
address 4-tuple.
To select a socket BPF program fetches it from a map holding socket
references, like SOCKMAP or SOCKHASH, calls bpf_sk_assign(ctx, sk, ...)
helper to record the selection, and returns SK_PASS code. Transport layer
then uses the selected socket as a result of socket lookup.
Alternatively, program can also fail the lookup (SK_DROP), or let the
lookup continue as usual (SK_PASS without selecting a socket).
This lets the user match packets with listening (TCP) or receiving (UDP)
sockets freely at the last possible point on the receive path, where we
know that packets are destined for local delivery after undergoing
policing, filtering, and routing.
Program is attached to a network namespace, similar to BPF flow_dissector.
We add a new attach type, BPF_SK_LOOKUP, for this. Multiple programs can be
attached at the same time, in which case their return values are aggregated
according the rules outlined in patch #4 description.
Series structure
================
Patches are organized as so:
1: enables multiple link-based prog attachments for bpf-netns
2: introduces sk_lookup program type
3-4: hook up the program to run on ipv4/tcp socket lookup
5-6: hook up the program to run on ipv6/tcp socket lookup
7-8: hook up the program to run on ipv4/udp socket lookup
9-10: hook up the program to run on ipv6/udp socket lookup
11-13: libbpf & bpftool support for sk_lookup
14-15: verifier and selftests for sk_lookup
Patches are also available on GH:
https://github.com/jsitnicki/linux/commits/bpf-inet-lookup-v5
Follow-up work
==============
I'll follow up with below items, which IMHO don't block the review:
- benchmark results for udp6 small packet flood scenario,
- user docs for new BPF prog type, Documentation/bpf/prog_sk_lookup.rst,
- timeout for accept() in tests after extending network_helper.[ch].
Thanks to the reviewers for their feedback to this patch series:
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Lorenz Bauer <lmb@cloudflare.com>
Cc: Marek Majkowski <marek@cloudflare.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Yonghong Song <yhs@fb.com>
-jkbs
[RFCv1] https://lore.kernel.org/bpf/20190618130050.8344-1-jakub@cloudflare.com/
[RFCv2] https://lore.kernel.org/bpf/20190828072250.29828-1-jakub@cloudflare.com/
[v1] https://lore.kernel.org/bpf/20200511185218.1422406-18-jakub@cloudflare.com/
[v2] https://lore.kernel.org/bpf/20200506125514.1020829-1-jakub@cloudflare.com/
[v3] https://lore.kernel.org/bpf/20200702092416.11961-1-jakub@cloudflare.com/
[v4] https://lore.kernel.org/bpf/20200713174654.642628-1-jakub@cloudflare.com/
====================
Reviewed-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Add tests to test_progs that exercise:
- attaching/detaching/querying programs to BPF_SK_LOOKUP hook,
- redirecting socket lookup to a socket selected by BPF program,
- failing a socket lookup on BPF program's request,
- error scenarios for selecting a socket from BPF program,
- accessing BPF program context,
- attaching and running multiple BPF programs.
Run log:
bash-5.0# ./test_progs -n 70
#70/1 query lookup prog:OK
#70/2 TCP IPv4 redir port:OK
#70/3 TCP IPv4 redir addr:OK
#70/4 TCP IPv4 redir with reuseport:OK
#70/5 TCP IPv4 redir skip reuseport:OK
#70/6 TCP IPv6 redir port:OK
#70/7 TCP IPv6 redir addr:OK
#70/8 TCP IPv4->IPv6 redir port:OK
#70/9 TCP IPv6 redir with reuseport:OK
#70/10 TCP IPv6 redir skip reuseport:OK
#70/11 UDP IPv4 redir port:OK
#70/12 UDP IPv4 redir addr:OK
#70/13 UDP IPv4 redir with reuseport:OK
#70/14 UDP IPv4 redir skip reuseport:OK
#70/15 UDP IPv6 redir port:OK
#70/16 UDP IPv6 redir addr:OK
#70/17 UDP IPv4->IPv6 redir port:OK
#70/18 UDP IPv6 redir and reuseport:OK
#70/19 UDP IPv6 redir skip reuseport:OK
#70/20 TCP IPv4 drop on lookup:OK
#70/21 TCP IPv6 drop on lookup:OK
#70/22 UDP IPv4 drop on lookup:OK
#70/23 UDP IPv6 drop on lookup:OK
#70/24 TCP IPv4 drop on reuseport:OK
#70/25 TCP IPv6 drop on reuseport:OK
#70/26 UDP IPv4 drop on reuseport:OK
#70/27 TCP IPv6 drop on reuseport:OK
#70/28 sk_assign returns EEXIST:OK
#70/29 sk_assign honors F_REPLACE:OK
#70/30 sk_assign accepts NULL socket:OK
#70/31 access ctx->sk:OK
#70/32 narrow access to ctx v4:OK
#70/33 narrow access to ctx v6:OK
#70/34 sk_assign rejects TCP established:OK
#70/35 sk_assign rejects UDP connected:OK
#70/36 multi prog - pass, pass:OK
#70/37 multi prog - drop, drop:OK
#70/38 multi prog - pass, drop:OK
#70/39 multi prog - drop, pass:OK
#70/40 multi prog - pass, redir:OK
#70/41 multi prog - redir, pass:OK
#70/42 multi prog - drop, redir:OK
#70/43 multi prog - redir, drop:OK
#70/44 multi prog - redir, redir:OK
#70 sk_lookup:OK
Summary: 1/44 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-16-jakub@cloudflare.com
|
|
Exercise verifier access checks for bpf_sk_lookup context fields.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-15-jakub@cloudflare.com
|
|
Make bpftool show human-friendly identifiers for newly introduced program
and attach type, BPF_PROG_TYPE_SK_LOOKUP and BPF_SK_LOOKUP, respectively.
Also, add the new prog type bash-completion, man page and help message.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-14-jakub@cloudflare.com
|
|
Make libbpf aware of the newly added program type, and assign it a
section name.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-13-jakub@cloudflare.com
|
|
Newly added program, context type and helper is used by tests in a
subsequent patch. Synchronize the header file.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-12-jakub@cloudflare.com
|
|
Same as for udp4, let BPF program override the socket lookup result, by
selecting a receiving socket of its choice or failing the lookup, if no
connected UDP socket matched packet 4-tuple.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-11-jakub@cloudflare.com
|
|
Prepare for calling into reuseport from __udp6_lib_lookup as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-10-jakub@cloudflare.com
|
|
Following INET/TCP socket lookup changes, modify UDP socket lookup to let
BPF program select a receiving socket before searching for a socket by
destination address and port as usual.
Lookup of connected sockets that match packet 4-tuple is unaffected by this
change. BPF program runs, and potentially overrides the lookup result, only
if a 4-tuple match was not found.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-9-jakub@cloudflare.com
|
|
Prepare for calling into reuseport from __udp4_lib_lookup as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-8-jakub@cloudflare.com
|
|
Following ipv4 stack changes, run a BPF program attached to netns before
looking up a listening socket. Program can return a listening socket to use
as result of socket lookup, fail the lookup, or take no action.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-7-jakub@cloudflare.com
|
|
Prepare for calling into reuseport from inet6_lookup_listener as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-6-jakub@cloudflare.com
|
|
Run a BPF program before looking up a listening socket on the receive path.
Program selects a listening socket to yield as result of socket lookup by
calling bpf_sk_assign() helper and returning SK_PASS code. Program can
revert its decision by assigning a NULL socket with bpf_sk_assign().
Alternatively, BPF program can also fail the lookup by returning with
SK_DROP, or let the lookup continue as usual with SK_PASS on return, when
no socket has been selected with bpf_sk_assign().
This lets the user match packets with listening sockets freely at the last
possible point on the receive path, where we know that packets are destined
for local delivery after undergoing policing, filtering, and routing.
With BPF code selecting the socket, directing packets destined to an IP
range or to a port range to a single socket becomes possible.
In case multiple programs are attached, they are run in series in the order
in which they were attached. The end result is determined from return codes
of all the programs according to following rules:
1. If any program returned SK_PASS and selected a valid socket, the socket
is used as result of socket lookup.
2. If more than one program returned SK_PASS and selected a socket,
last selection takes effect.
3. If any program returned SK_DROP, and no program returned SK_PASS and
selected a socket, socket lookup fails with -ECONNREFUSED.
4. If all programs returned SK_PASS and none of them selected a socket,
socket lookup continues to htable-based lookup.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-5-jakub@cloudflare.com
|
|
Prepare for calling into reuseport from __inet_lookup_listener as well.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-4-jakub@cloudflare.com
|
|
Add a new program type BPF_PROG_TYPE_SK_LOOKUP with a dedicated attach type
BPF_SK_LOOKUP. The new program kind is to be invoked by the transport layer
when looking up a listening socket for a new connection request for
connection oriented protocols, or when looking up an unconnected socket for
a packet for connection-less protocols.
When called, SK_LOOKUP BPF program can select a socket that will receive
the packet. This serves as a mechanism to overcome the limits of what
bind() API allows to express. Two use-cases driving this work are:
(1) steer packets destined to an IP range, on fixed port to a socket
192.0.2.0/24, port 80 -> NGINX socket
(2) steer packets destined to an IP address, on any port to a socket
198.51.100.1, any port -> L7 proxy socket
In its run-time context program receives information about the packet that
triggered the socket lookup. Namely IP version, L4 protocol identifier, and
address 4-tuple. Context can be further extended to include ingress
interface identifier.
To select a socket BPF program fetches it from a map holding socket
references, like SOCKMAP or SOCKHASH, and calls bpf_sk_assign(ctx, sk, ...)
helper to record the selection. Transport layer then uses the selected
socket as a result of socket lookup.
In its basic form, SK_LOOKUP acts as a filter and hence must return either
SK_PASS or SK_DROP. If the program returns with SK_PASS, transport should
look for a socket to receive the packet, or use the one selected by the
program if available, while SK_DROP informs the transport layer that the
lookup should fail.
This patch only enables the user to attach an SK_LOOKUP program to a
network namespace. Subsequent patches hook it up to run on local delivery
path in ipv4 and ipv6 stacks.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-3-jakub@cloudflare.com
|
|
Extend the BPF netns link callbacks to rebuild (grow/shrink) or update the
prog_array at given position when link gets attached/updated/released.
This let's us lift the limit of having just one link attached for the new
attach type introduced by subsequent patch.
No functional changes intended.
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200717103536.397595-2-jakub@cloudflare.com
|
|
Fix wrong reading of upper pages for SFP EEPROM. According to "Memory
Organization" figure in SFF-8472 spec: When reading upper pages 1, 2 and
3 the offset should be set relative to zero and I2C high address 0x51
[1010001X (A2h)] is to be used.
Fixes: a45bfb5a5070 ("mlxsw: core: Extend QSFP EEPROM size for ethtool")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netif_msg_enable() to process param settings.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mark Starovoytov says:
====================
net: atlantic: add support for FW 4.x
This patch set adds support for FW 4.x, which is about to get into the
production for some products.
4.x is mostly compatible with 3.x, save for soft reset, which requires
the acquisition of 2 additional semaphores.
Other differences (e.g. absence of PTP support) are handled via
capabilities.
Note: 4.x targets specific products only. 3.x is still the main firmware
branch, which should be used by most users (at least for now).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for FW 4.x, which is about to get into the
production for some products.
4.x is mostly compatible with 3.x, save for soft reset, which requires
the acquisition of 2 additional semaphores.
Other differences (e.g. absence of PTP support) are handled via
capabilities.
Note: 4.x targets specific products only. 3.x is still the main firmware
branch, which should be used by most users (at least for now).
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch aligns the return value of hw_atl_utils_ver_match function with
its name.
Change the return type to bool, because it's better aligned with the actual
usage. Return true when the version matches, false otherwise.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Validate MAC address before copying the same to outgoing frame
skb destination address. Since a node can have zero mac
address for Link B until a valid frame is received over
that link, this fix address the issue of a zero MAC address
being in the packet.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For small Ethernet frames with size less than minimum size 66 for HSR
vs 60 for regular Ethernet frames, hsr driver currently doesn't pad the
frame to make it minimum size. This results in incorrect LSDU size being
populated in the HSR tag for these frames. Fix this by padding the frame
to the minimum size applicable for HSR.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the removal of an unused variable assignment (remove
unused variable 'pm_csr') the associated register read can also go,
as the read also occurs in the subsequent et1310_in_phy_coma()
call.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gcc report warning as follows:
drivers/net/ethernet/agere/et131x.c:953:6: warning:
variable 'pm_csr' set but not used [-Wunused-but-set-variable]
953 | u32 pm_csr;
| ^~~~~~
drivers/net/ethernet/agere/et131x.c:1002:6:warning:
variable 'pm_csr' set but not used [-Wunused-but-set-variable]
1002 | u32 pm_csr;
| ^~~~~~
drivers/net/ethernet/agere/et131x.c:3446:8: warning:
variable 'pm_csr' set but not used [-Wunused-but-set-variable]
3446 | u32 pm_csr;
| ^~~~~~
After commit 38df6492eb51 ("et131x: Add PCIe gigabit ethernet driver
et131x to drivers/net"), 'pm_csr' is never used in these functions,
so removing it to avoid build warning.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gcc report warning as follows:
drivers/net/ethernet/brocade/bna/bfa_ioc.c:1538:6: warning:
variable 't' set but not used [-Wunused-but-set-variable]
1538 | u32 t;
| ^
After commit c107ba171f3d ("bna: Firmware Patch Simplification"),
't' is never used, so removing it to avoid build warning.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The double poll additions were centered around doing POLL_ADD on file
descriptors that use more than one waitqueue (typically one for read,
one for write) when being polled. However, it can also end up being
triggered for when we use poll triggered retry. For that case, we cannot
safely use req->io, as that could be used by the request type itself.
Add a second io_poll_iocb pointer in the structure we allocate for poll
based retry, and ensure we use the right one from the two paths.
Fixes: 18bceab101ad ("io_uring: allow POLL_ADD with double poll_wait() users")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Drop the doubled word "be" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is one RGMII check not using the phy_interface_mode_is_rgmii()
helper. This prevents the driver from configuring the MAC properly when
using a phy-mode that is not just rgmii, e.g. rgmii-rxid. This became an
issue on sama5d3 xplained since the ksz9031 driver is hadling phy-mode
properly and the phy-mode has to be set to rgmii-rxid.
Fixes: bcf3440c6dd78bfe ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fact that NETIF_F_HW_TC is not set should be a sufficient
indication to the user that TC offloads are not supported.
No need to bother users of older firmware versions with
pointless warnings on every boot.
Also, since the support is optional, bnxt_init_tc() should not
return an error in case FW is old, similarly to how error
is not returned when CONFIG_BNXT_FLOWER_OFFLOAD is not set.
With that we can add an error message to the caller, to warn
about actual unexpected failures.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch disables PTP on AQC111 and AQC112 due to a known HW issue,
which can cause datapath issues.
Ideally PTP block should have been disabled via PHY provisioning, but
unfortunately many units have been shipped with enabled PTP block.
Thus, we have to work around this in the driver.
Fixes: dbcd6806af420 ("net: aquantia: add support for Phy access")
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into master
Pull NFS client fixes from Anna Schumaker:
"A few more NFS client bugfixes for Linux 5.8:
NFS:
- Fix interrupted slots by using the SEQUENCE operation
SUNRPC:
- revert d03727b248d0 to fix unkillable IOs
xprtrdma:
- Fix double-free in rpcrdma_ep_create()
- Fix recursion into rpcrdma_xprt_disconnect()
- Fix return code from rpcrdma_xprt_connect()
- Fix handling of connect errors
- Fix incorrect header size calculations"
* tag 'nfs-for-5.8-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC reverting d03727b248d0 ("NFSv4 fix CLOSE not waiting for direct IO compeletion")
xprtrdma: fix incorrect header size calculations
NFS: Fix interrupted slots by sending a solo SEQUENCE operation
xprtrdma: Fix handling of connect errors
xprtrdma: Fix return code from rpcrdma_xprt_connect()
xprtrdma: Fix recursion into rpcrdma_xprt_disconnect()
xprtrdma: Fix double-free in rpcrdma_ep_create()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into master
Pull ARM SoC fixes from Arnd Bergmann:
"This time there are a number of actual code fixes, plus a small set of
device tree issues getting addressed:
Renesas:
- one defconfig cleanup to allow a later Kconfig change
Intel socfpga:
- enable QSPI devices on some machines
- fix DTC validation warnings
TI OMAP:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target
module driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
NXP i.MX:
- A couple of fixes on i.MX platform device registration code to
stop the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit
52102a3ba6a61 ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
Amlogic Meson:
- misc DT fixes
- SoC ID fixes to detect all chips correctly"
* tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema
ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema
arm64: dts: stratix10: increase QSPI reg address in nand dts file
arm64: dts: stratix10: add status to qspi dts node
arm64: dts: agilex: add status to qspi dts node
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
ARM: dts: meson: Align L2 cache-controller nodename with dtschema
arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
arm64: dts: meson: add missing gxl rng clock
soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux into master
Pull arm64 fixes from Will Deacon:
"A batch of arm64 fixes.
Although the diffstat is a bit larger than we'd usually have at this
stage, a decent amount of it is the addition of comments describing
our syscall tracing behaviour, and also a sweep across all the modular
arm64 PMU drivers to make them rebust against unloading and unbinding.
There are a couple of minor things kicking around at the moment (CPU
errata and module PLTs for very large modules), but I'm not expecting
any significant changes now for us in 5.8.
- Fix kernel text addresses for relocatable images booting using EFI
and with KASLR disabled so that they match the vmlinux ELF binary.
- Fix unloading and unbinding of PMU driver modules.
- Fix generic mmiowb() when writeX() is called from preemptible
context (reported by the riscv folks).
- Fix ptrace hardware single-step interactions with signal handlers,
system calls and reverse debugging.
- Fix reporting of 64-bit x0 register for 32-bit tasks via
'perf_regs'.
- Add comments describing syscall entry/exit tracing ABI"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
drivers/perf: Prevent forced unbinding of PMU drivers
asm-generic/mmiowb: Allow mmiowb_set_pending() when preemptible()
arm64: Use test_tsk_thread_flag() for checking TIF_SINGLESTEP
arm64: ptrace: Use NO_SYSCALL instead of -1 in syscall_trace_enter()
arm64: syscall: Expand the comment about ptrace and syscall(-1)
arm64: ptrace: Add a comment describing our syscall entry/exit trap ABI
arm64: compat: Ensure upper 32 bits of x0 are zero on syscall return
arm64: ptrace: Override SPSR.SS when single-stepping is enabled
arm64: ptrace: Consistently use pseudo-singlestep exceptions
drivers/perf: Fix kernel panic when rmmod PMU modules during perf sampling
efi/libstub/arm64: Retain 2MB kernel Image alignment if !KASLR
|
|
Setting interrupt affinity on inactive interrupts is inconsistent when
hierarchical irq domains are enabled. The core code should just store the
affinity and not call into the irq chip driver for inactive interrupts
because the chip drivers may not be in a state to handle such requests.
X86 has a hacky workaround for that but all other irq chips have not which
causes problems e.g. on GIC V3 ITS.
Instead of adding more ugly hacks all over the place, solve the problem in
the core code. If the affinity is set on an inactive interrupt then:
- Store it in the irq descriptors affinity mask
- Update the effective affinity to reflect that so user space has
a consistent view
- Don't call into the irq chip driver
This is the core equivalent of the X86 workaround and works correctly
because the affinity setting is established in the irq chip when the
interrupt is activated later on.
Note, that this is only effective when hierarchical irq domains are enabled
by the architecture. Doing it unconditionally would break legacy irq chip
implementations.
For hierarchial irq domains this works correctly as none of the drivers can
have a dependency on affinity setting in inactive state by design.
Remove the X86 workaround as it is not longer required.
Fixes: 02edee152d6e ("x86/apic/vector: Ignore set_affinity call for inactive interrupts")
Reported-by: Ali Saidi <alisaidi@amazon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ali Saidi <alisaidi@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200529015501.15771-1-alisaidi@amazon.com
Link: https://lkml.kernel.org/r/877dv2rv25.fsf@nanos.tec.linutronix.de
|
|
When nfc_register_device fails in nci_register_device,
destroy_workqueue() shouled be called to destroy ndev->tx_wq.
Fixes: 3c1c0f5dc80b ("NFC: NCI: Fix nci_register_device init sequence")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-07-16
Fixes:
1) Fix build break when CONFIG_XPS is not set
2) Fix missing switch_id for representors
Updates:
1) IPsec XFRM RX offloads from Raed and Huy.
- Added IPSec RX steering flow tables to NIC RX
- Refactoring of the existing FPGA IPSec, to add support
for ConnectX IPsec.
- RX data path handling for IPSec traffic
- Synchronize offloading device ESN with xfrm received SN
2) Parav allows E-Switch to siwtch to switchdev mode directly without
the need to go through legacy mode first.
3) From Tariq, Misc updates including:
3.1) indirect calls for RX and XDP handlers
3.2) Make MLX5_EN_TLS non-prompt as it should always be enabled when
TLS and MLX5_EN are selected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Doug Berger says:
====================
net: bcmgenet: fix WAKE_FILTER resume from deep sleep
The WAKE_FILTER logic can only wake the system from the standby
power state. However, some systems that include the GENET IP
support deeper power saving states and the driver should suspend
and resume correctly from those states as well.
This commit set squashes a few issues uncovered while testing
suspend and resume from these deep sleep states.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Hardware Filter Block RAM may not be preserved when the GENET
block is reset during a deep sleep, so it is not sufficient to
only backup and restore the enables.
This commit clears out the HFB block and reprograms the rxnfc
rules when the system resumes from a suspended state. To support
this the bcmgenet_hfb_create_rxnfc_filter() function is modified
to access the register space directly so that it can't fail due
to memory allocation issues.
Fixes: f50932cca632 ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the GENET driver resumes from deep sleep the UMAC_CMD
register may not be accessible and therefore should not be
accessed from bcmgenet_wol_power_up_cfg() if the GENET has
been reset.
This commit adds a check of the RBUF_ACPI_EN flag when Wake
on Filter is enabled. A clear flag indicates that the GENET
hardware must have been reset so the remainder of the
hardware programming is bypassed.
Fixes: f50932cca632 ("net: bcmgenet: add WAKE_FILTER support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
