| Age | Commit message (Collapse) | Author |
|---|
|
Enable IOMMU_DEV_FEAT_SVA before attempt to bind pasid. This is needed
according to iommu_sva_bind_device() comment. Currently Intel IOMMU code
does this before bind call. It really needs to be controlled by the driver.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894440621.3202472.17644507396206848134.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Convert sprintf() to sysfs_emit() in order to check buffer overrun on sysfs
outputs.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894440044.3202472.13926639619695319753.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
DSA spec states that when Request Interrupt Handle and Release Interrupt
Handle command bits are set in the CMDCAP register, these device commands
must be supported by the driver.
The interrupt handle is programmed in a descriptor. When Request Interrupt
Handle is not supported, the interrupt handle is the index of the desired
entry in the MSI-X table. When the command is supported, driver must use
the command to obtain a handle to be programmed in the submitted
descriptor.
A requested handle may be revoked. After the handle is revoked, any use of
the handle will result in Invalid Interrupt Handle error.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894439422.3202472.17579543737810265471.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The read-only configuration mode is defined by the DSA spec as a mode of
the device WQ configuration. When GENCAP register bit 31 is set to 0,
the device is in RO mode and group configuration and some fields of the
workqueue configuration registers are read-only and reflect the fixed
configuration of the device. Add support for RO mode. The driver will
load the values from the registers directly setup all the internally
cached data structures based on the device configuration.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894438847.3202472.6317563824045432727.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Current submission path has no way to restrict the submitter from
stop submiting on shutdown path or wq disable path. This provides a way to
quiesce the submission path.
Modeling after 'struct reqeust_queue' usage of percpu_ref. One of the
abilities of per_cpu reference counting is the ability to stop new
references from being taken while awaiting outstanding references to be
dropped. On wq shutdown, we want to block any new submissions to the kernel
workqueue and quiesce before disabling. The percpu_ref allows us to block
any new submissions and wait for any current submission calls to finish
submitting to the workqueue.
A percpu_ref is embedded in each idxd_wq context to allow control for
individual wq. The wq->wq_active counter is elevated before calling
movdir64b() or enqcmds() to submit a descriptor to the wq and dropped once
the submission call completes. The function is gated by
percpu_ref_tryget_live(). On shutdown with percpu_ref_kill() called, any
new submission would be blocked from acquiring a ref and failed. Once all
references are dropped for the wq, shutdown can continue.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161894438293.3202472.14894701611500822232.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"Just some small i915 and amdgpu fixes this week, should be all until
you open the merge window.
amdgpu:
- Fix gpuvm page table update issue
- Modifier fixes
- Register fix for dimgrey cavefish
i915:
- GVT's BDW regression fix for cmd parser
- Fix modesetting in case of unexpected AUX timeouts"
* tag 'drm-fixes-2021-04-23' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: fix GCR_GENERAL_CNTL offset for dimgrey_cavefish
amd/display: allow non-linear multi-planar formats
drm/amd/display: Update modifier list for gfx10_3
drm/amdgpu: reserve fence slot to update page table
drm/i915: Fix modesetting in case of unexpected AUX timeouts
drm/i915/gvt: Fix BDW command parser regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
"Save and restore the sysconfig register in gpio-omap to fix a
power-management issue"
* tag 'gpio-fixes-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: omap: Save and restore sysconfig
|
|
From: Alexey Klimov <klimov.linux@gmail.com>
Add the B550M AORUS PRO-P motherboard description to
gigabyte_wmi_known_working_platforms.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Thomas Weißschuh <thomas@weissschuh.net>
Link: https://lore.kernel.org/r/20210421234156.3942343-1-aklimov@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
A KernelCI bisection identified 59c35c44a9cf89 "ASoC: simple-card: add
simple_parse_node()" as causing simple-card to fail to instantiate on
kontron-sl28-var3-ads2 systems. Since the merge window is expected to
open over the weekend drop that commit and subsequent ones which depend
on it for now in case other systems are affected too.
The boot log showed the error as:
<4>[ 9.948821] sysfs: cannot create duplicate filename '/devices/platform/sound/(null)-wm8904-hifi'
(backtrace)
<3>[ 10.191982] kobject_add_internal failed for (null)-wm8904-hifi with -EEXIST, don't try to register things with the same name in the same directory.
The dropped commits are:
73371bacf0475a20ab6 "ASoC: audio-graph: tidyup graph_dai_link_of_dpcm()"
434392271afcff350fe "ASoC: simple-card: add simple_link_init()"
59c35c44a9cf89a83a9 "ASoC: simple-card: add simple_parse_node()"
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the calculation of the register value determining the duty cycle the
requested period is used instead of the actually implemented period which
results in suboptimal settings.
The following example assumes an input clock of 133333333 Hz on one of
the SoCs with 16 bit period.
When the following state is to be applied:
.period = 414727681
.duty_cycle = 652806
the following register values used to be calculated:
PRES = 10
CPRD = 54000
CDTY = 53916
which yields an actual duty cycle of a bit more than 645120 ns.
The setting
PRES = 10
CPRD = 54000
CDTY = 53915
however yields a duty of 652800 ns which is between the current result
and the requested value and so is a better approximation.
The reason for this error is that for the calculation of CDTY the
requested period was used instead of the actually implemented one.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The CDTY register contains the number of inactive cycles. .apply() does
this correctly, however .get_state() got this wrong.
Fixes: 651b510a74d4 ("pwm: atmel: Implement .get_state()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add driver for the PWM controller on Toshiba Visconti ARM SoC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[thierry.reding@gmail.com: fix up a couple of checkpatch warnings]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
When using ACPI on arm64, which implies the GIC IRQ model, no
table should ever provide a GSI number in the range [0:15],
as these are reserved for IPIs.
However, drivers tend to call acpi_unregister_gsi() with any
random GSI number provided by half baked tables, which results
in an exploding kernel when its IPIs have been unconfigured.
In order to catch this, check for the silly case early, warn
that something is going wrong and avoid the above disaster.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20210421164317.1718831-3-maz@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When failing the driver probe because of invalid firmware properties,
the GTDT driver unmaps the interrupt that it mapped earlier.
However, it never checks whether the mapping of the interrupt actially
succeeded. Even more, should the firmware report an illegal interrupt
number that overlaps with the GIC SGI range, this can result in an
IPI being unmapped, and subsequent fireworks (as reported by Dann
Frazier).
Rework the driver to have a slightly saner behaviour and actually
check whether the interrupt has been mapped before unmapping things.
Reported-by: dann frazier <dann.frazier@canonical.com>
Fixes: ca9ae5ec4ef0 ("acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/YH87dtTfwYgavusz@xps13.dannf
Cc: <stable@vger.kernel.org>
Cc: Fu Wei <wefu@redhat.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: dann frazier <dann.frazier@canonical.com>
Tested-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20210421164317.1718831-2-maz@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Displaying two registers per line takes 15 lines. That improves to just
10 lines if we display three registers per line, which reduces the amount
of information lost when oopses are cut off. It stays within 80 columns
and matches x86-64.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210420172245.3679077-1-willy@infradead.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Florent Revest says:
====================
Alexei requested a couple of cleanups to the bpf_snprintf and
ARG_PTR_TO_CONST_STR verifier code.
https://lore.kernel.org/bpf/CABRcYmL_SMT80UTyV98bRsOzW0wBd1sZcYUpTrcOAV+9m+YoWQ@mail.gmail.com/T/#t
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
reg->type is enforced by check_reg_type() and map should never be NULL
(it would already have been dereferenced anyway) so these checks are
unnecessary.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210422235543.4007694-3-revest@chromium.org
|
|
In check_bpf_snprintf_call(), a map_direct_value_addr() of the fmt map
should never fail because it has already been checked by
ARG_PTR_TO_CONST_STR. But if it ever fails, it's better to error out
with an explicit debug message rather than silently fail.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210422235543.4007694-2-revest@chromium.org
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/song/md into for-5.13/drivers
Pull MD fixes from Song.
* 'md-next' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
md/raid1: properly indicate failure when ending a failed write request
md-cluster: fix use-after-free issue when removing rdev
|
|
Add bindings for the Toshiba Visconti PWM Controller.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3368-evb-act8846.dt.yaml:
pwm@ff680030: clock-names: ['pwm'] is too short
Devices with only one PWM clock use it to both to derive the functional
clock for the device and as the bus clock. The driver does not need
"clock-names" to get a handle, so remove them all.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/pwm/pwm-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
A test with the command below gives this error:
/arch/arm/boot/dts/rk3036-evb.dt.yaml:
pwm@20050030: clock-names: ['pwm'] is too short
Devices with only one PWM clock use it to both to derive the functional
clock for the device and as the bus clock. The driver does not need
"clock-names" to get a handle, so remove them all.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/pwm/pwm-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The compatible strings below are already in use in the Rockchip
DTSI files, but were somehow never added to a document, so add
"rockchip,rk3328-pwm"
"rockchip,rk3036-pwm", "rockchip,rk2928-pwm"
"rockchip,rk3368-pwm", "rockchip,rk3288-pwm"
"rockchip,rk3399-pwm", "rockchip,rk3288-pwm"
"rockchip,px30-pwm", "rockchip,rk3328-pwm"
"rockchip,rk3308-pwm", "rockchip,rk3328-pwm"
for PWM nodes to pwm-rockchip.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Current dts files with 'pwm' nodes are manually verified. In order to
automate this process pwm-rockchip.txt has to be converted to YAML.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Fix the following clang warning:
drivers/pwm/pwm-mediatek.c:110:19: warning: unused function
'pwm_mediatek_readl' [-Wunused-function].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The chip does not come out of POR in active state but in sleep state.
To be sure (in case the bootloader woke it up) we force it to sleep in
probe.
If runtime PM is disabled, we instead wake the chip in .probe and put it
to sleep in .remove.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Implement .get_state to read-out the current hardware state.
The hardware readout may return slightly different values than those
that were set in apply due to the limited range of possible prescale and
counter register values.
Also note that although the datasheet mentions 200 Hz as default
frequency when using the internal 25 MHz oscillator, the calculated
period from the default prescaler register setting of 30 is 5079040ns.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The switch to the atomic API goes hand in hand with a few fixes to
previously experienced issues:
- The duty cycle is no longer lost after disable/enable (previously the
OFF registers were cleared in disable and the user was required to
call config to restore the duty cycle settings)
- If one sets a period resulting in the same prescale register value,
the sleep and write to the register is now skipped
- Previously, only the full ON bit was toggled in GPIO mode (and full
OFF cleared if set to high), which could result in both full OFF and
full ON not being set and on=0, off=0, which is not allowed according
to the datasheet
- The OFF registers were reset to 0 in probe, which could lead to the
forbidden on=0, off=0. Fixed by resetting to POR default (full OFF)
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This patch addresses a data corruption bug in raid1 arrays using bitmaps.
Without this fix, the bitmap bits for the failed I/O end up being cleared.
Since we are in the failure leg of raid1_end_write_request, the request
either needs to be retried (R1BIO_WriteError) or failed (R1BIO_Degraded).
Fixes: eeba6809d8d5 ("md/raid1: end bio when the device faulty")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Paul Clements <paul.clements@us.sios.com>
Signed-off-by: Song Liu <song@kernel.org>
|
|
md_kick_rdev_from_array will remove rdev, so we should
use rdev_for_each_safe to search list.
How to trigger:
env: Two nodes on kvm-qemu x86_64 VMs (2C2G with 2 iscsi luns).
```
node2=192.168.0.3
for i in {1..20}; do
echo ==== $i `date` ====;
mdadm -Ss && ssh ${node2} "mdadm -Ss"
wipefs -a /dev/sda /dev/sdb
mdadm -CR /dev/md0 -b clustered -e 1.2 -n 2 -l 1 /dev/sda \
/dev/sdb --assume-clean
ssh ${node2} "mdadm -A /dev/md0 /dev/sda /dev/sdb"
mdadm --wait /dev/md0
ssh ${node2} "mdadm --wait /dev/md0"
mdadm --manage /dev/md0 --fail /dev/sda --remove /dev/sda
sleep 1
done
```
Crash stack:
```
stack segment: 0000 [#1] SMP
... ...
RIP: 0010:md_check_recovery+0x1e8/0x570 [md_mod]
... ...
RSP: 0018:ffffb149807a7d68 EFLAGS: 00010207
RAX: 0000000000000000 RBX: ffff9d494c180800 RCX: ffff9d490fc01e50
RDX: fffff047c0ed8308 RSI: 0000000000000246 RDI: 0000000000000246
RBP: 6b6b6b6b6b6b6b6b R08: ffff9d490fc01e40 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000
R13: ffff9d494c180818 R14: ffff9d493399ef38 R15: ffff9d4933a1d800
FS: 0000000000000000(0000) GS:ffff9d494f700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe68cab9010 CR3: 000000004c6be001 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
raid1d+0x5c/0xd40 [raid1]
? finish_task_switch+0x75/0x2a0
? lock_timer_base+0x67/0x80
? try_to_del_timer_sync+0x4d/0x80
? del_timer_sync+0x41/0x50
? schedule_timeout+0x254/0x2d0
? md_start_sync+0xe0/0xe0 [md_mod]
? md_thread+0x127/0x160 [md_mod]
md_thread+0x127/0x160 [md_mod]
? wait_woken+0x80/0x80
kthread+0x10d/0x130
? kthread_park+0xa0/0xa0
ret_from_fork+0x1f/0x40
```
Fixes: dbb64f8635f5d ("md-cluster: Fix adding of new disk with new reload code")
Fixes: 659b254fa7392 ("md-cluster: remove a disk asynchronously from cluster environment")
Cc: stable@vger.kernel.org
Reviewed-by: Gang He <ghe@suse.com>
Signed-off-by: Heming Zhao <heming.zhao@suse.com>
Signed-off-by: Song Liu <song@kernel.org>
|
|
The flex-byte for GTP-U protocol header fields uses the magic number,
which is hard to maintain and understand, define the interested fields
with meaningful macro name, based on the GTP-U protocol stack:
GTP-U header
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x1 |1|0|1|0|0| 0xff | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TEID = 1654 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number = 0 |N-PDU Number=0 |NextExtHdr=0x85|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
GTP-U Extension Header (PDU Session Container)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ExtHdrLen=2 |Type=0 | Spare |0|0| QFI | PPI | Spare |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Padding |NextExtHdr=0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When the FDIR entry is found, just return the result directly to break
the loop.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The maximum number (2) of flex-byte support is derived from ethtool
use-def data size (8 byte).
Change the magic number 2 to macro definition, and add the comment to
track the design thinking, so the code is clear and easily maintained.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Both iavf_free_all_tx_resources() and iavf_free_all_rx_resources() have
already been called in the very same function.
Remove the duplicate calls.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The minimum size of admin send/receive queue is 1 and 2 respectively.
The admin send queue can't be set to 1 because in that case, the
firmware would fail to init.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use the minimum of the number of descriptors thus we will allocate the
minimal ring buffers for kdump.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Set the number of the MSI-X vectors to 1. When MSI-X is enabled,
it's not allowed to use more TC queue pairs than MSI-X vectors
(pf->num_lan_msix) exist. Thus the number of Tx and Rx pairs
(vsi->num_queue_pairs) will be equal to the number of MSI-X vectors,
i.e., 1.
Signed-off-by: Coiby Xu <coxu@redhat.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Refactor repeated link state reporting code into a separate helper
functions: i40e_set_vf_link_state() i40e_vc_link_speed2mbps().
Add support of VIRTCHNL_VF_CAP_ADV_LINK_SPEED;
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 9af7706492f9 ("lib/vsprintf: Remove support for %pF and %pf in
favour of %pS and %ps") removed support for %pF and %pf, and correctly
removed the handling of those cases in vbin_printf(). However, the
corresponding cases in bstr_printf() were left behind.
In the same series, %pf was re-purposed for dealing with
fwnodes (3bd32d6a2ee6, "lib/vsprintf: Add %pfw conversion specifier
for printing fwnode names").
So should anyone use %pf with the binary printf routines,
vbin_printf() would (correctly, as it involves dereferencing the
pointer) do the string formatting to the u32 array, but bstr_printf()
would not copy the string from the u32 array, but instead interpret
the first sizeof(void*) bytes of the formatted string as a pointer -
which generally won't end well (also, all subsequent get_args would be
out of sync).
Fixes: 9af7706492f9 ("lib/vsprintf: Remove support for %pF and %pf in favour of %pS and %ps")
Cc: stable@vger.kernel.org
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210423094529.1862521-1-linux@rasmusvillemoes.dk
|
|
When alloc_pages_node() returns null in svc_rqst_alloc(), the
null rq_scratch_page pointer will be dereferenced when calling
put_page() in svc_rqst_free(). Fix it by adding a null check.
Addresses-Coverity: ("Dereference after null check")
Fixes: 5191955d6fc6 ("SUNRPC: Prepare for xdr_stream-style decoding on the server-side")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
The enable1 is confusing name. Change it to clearly show what is
the intention behind it. No functional changes.
Fixes: 25093bdeb6bc ("spi: implement SW control for CS times")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210420131846.75983-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a compatible string to support TCS4525/TCS4526 devices,
which are compatible with Fairchild FAN53555 regulators.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210421210338.43819-2-ezequiel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TCS4525 main features:
- 2.7V to 5.5V Input Voltage Range;
- 3MHz Constant Switching Frequency;
- 5A Available Load Current;
- Programmable Output Voltage: 0.6V to 1.4V in 6.25mV Steps;
- PFM/PWM Operation for Optimum Increased Efficiency;
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[Ezequiel: Forward port]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210421210338.43819-3-ezequiel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Shenzhen City Tang Cheng Technology (http://www.tctek.cn/)
is a power management IC manufacturer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210421210338.43819-1-ezequiel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds the return value when the volume settings were changed.
The userspace application might monitor the kcontrols to check which control changed.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210422103235.22048-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DAPM event and mixer control could mute/unmute the capture directly.
That will be confused that capture still works if the user settings is unmute before the capture.
Therefore, this patch uses the variables to record the capture switch status of DAPM and mixer.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20210422103220.21987-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
do this to avoid race below:
userspace kernel
| check sqring and iopoll_list
submit sqe |
check IORING_SQ_NEED_WAKEUP |
(which is not set) | |
| set IORING_SQ_NEED_WAKEUP
wait cqe | schedule(never wakeup again)
Signed-off-by: Hao Xu <haoxu@linux.alibaba.com>
Link: https://lore.kernel.org/r/1619018351-75883-1-git-send-email-haoxu@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
arm64: tegra: Device tree fixes for v5.12-rc6
This contains a couple of device tree fixes for the v5.12 release cycle.
These are needed for proper audio support on Jetson AGX Xavier, to boot
the Jetson Xavier NX from an SD card and to be able to suspend/resume
the Jetson TX2.
* tegra/dt64:
arm64: tegra: Move clocks from RT5658 endpoint to device node
arm64: tegra: Fix mmc0 alias for Jetson Xavier NX
arm64: tegra: Set fw_devlink=on for Jetson TX2
arm64: tegra: Add unit-address for ACONNECT on Tegra186
Link: https://lore.kernel.org/linux-arm-kernel/YILD4yyPXuiYbHW1@orome.fritz.box/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
After commit 9fb7410f955f ("arm64/BUG: Use BRK instruction for generic
BUG traps"), arm64 has switched to generic BUG implementation, so
there's no need to select HAVE_DEBUG_BUGVERBOSE.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210418215231.563d4b72@xhacker
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In __apply_alternatives() we take a pointer to void which we later
assign to a pointer to struct alt_region. As all callers are passing a
pointer to struct alt_region to begin with, it's simpler and more robust
to take a pointer to struct alt region, so let's do so and avoid the
need for a temporary variable.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210416163032.10857-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
