| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One notable fix to properly advertise our support for a new firmware
feature, caused by two series conflicting semantically but not
textually.
There's a new ioctl for the new ocxl driver, which is not a fix, but
needed to complete the userspace API and good to have before the
driver is in a released kernel.
Finally three minor selftest fixes, and a fix for intermittent build
failures for some obscure platforms, caused by a missing make
dependency.
Thanks to: Alastair D'Silva, Bharata B Rao, Guenter Roeck"
* tag 'powerpc-4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Fix vector5 in ibm architecture vector table
ocxl: Document the OCXL_IOCTL_GET_METADATA IOCTL
ocxl: Add get_metadata IOCTL to share OCXL information to userspace
selftests/powerpc: Skip the subpage_prot tests if the syscall is unavailable
selftests/powerpc: Fix missing clean of pmu/lib.o
powerpc/boot: Fix random libfdt related build errors
selftests/powerpc: Skip tm-trap if transactional memory is not enabled
|
|
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch reverts the commit 835e4241e714 ("usb: host: xhci-plat:
enable clk in resume timing") because this driver also has runtime PM
and the commit 560869100b99 ("clk: renesas: cpg-mssr: Restore module
clocks during resume") will restore the clock on R-Car H3 environment.
If the xhci_plat_suspend() disables the clk, the system cannot enable
the clk in resume like the following behavior:
< In resume >
- genpd_resume_noirq() runs and enable the clk (enable_count = 1)
- cpg_mssr_resume_noirq() restores the clk register.
-- Since the clk was disabled in suspend, cpg_mssr_resume_noirq()
will disable the clk and keep the enable_count.
- Even if xhci_plat_resume() calls clk_prepare_enable(), since
the enable_count is 1, the clk will be not enabled.
After this patch is applied, the cpg-mssr driver will save the clk
as enable, so the clk will be enabled in resume.
Fixes: 835e4241e714 ("usb: host: xhci-plat: enable clk in resume timing")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Moved 16bit resolution condition check for stoney platform
to acp_hw_params.Depending upon substream required register
value need to be programmed rather than enabling 16bit resolution
support all time in acp init.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This change fixes buffer overflows and silent data corruption with the
usbmon device driver text file read operations.
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following commit:
commit aa4d86163e4e ("block: loop: switch to VFS ITER_BVEC")
replaced __do_lo_send_write(), which used ITER_KVEC iterators, with
lo_write_bvec() which uses ITER_BVEC iterators. In this change, though,
the WRITE flag was lost:
- iov_iter_kvec(&from, ITER_KVEC | WRITE, &kvec, 1, len);
+ iov_iter_bvec(&i, ITER_BVEC, bvec, 1, bvec->bv_len);
This flag is necessary for the DAX case because we make decisions based on
whether or not the iterator is a READ or a WRITE in dax_iomap_actor() and
in dax_iomap_rw().
We end up going through this path in configurations where we combine a PMEM
device with 4k sectors, a loopback device and DAX. The consequence of this
missed flag is that what we intend as a write actually turns into a read in
the DAX code, so no data is ever written.
The very simplest test case is to create a loopback device and try and
write a small string to it, then hexdump a few bytes of the device to see
if the write took. Without this patch you read back all zeros, with this
you read back the string you wrote.
For XFS this causes us to fail or panic during the following xfstests:
xfs/074 xfs/078 xfs/216 xfs/217 xfs/250
For ext4 we have a similar issue where writes never happen, but we don't
currently have any xfstests that use loopback and show this issue.
Fix this by restoring the WRITE flag argument to iov_iter_bvec(). This
causes the xfstests to all pass.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Fixes: commit aa4d86163e4e ("block: loop: switch to VFS ITER_BVEC")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When populating shadow ctx from guest, we should handle oa related
registers in hw ctx, so that they will not be overlapped by guest oa
configs. This patch made it possible to capture oa data from host for
both host and guests.
Signed-off-by: Min He <min.he@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
|
|
If user continuously create vgpu, boot guest, shoutdown guest and destroy
vgpu from remote, the following calltrace exists in dmesg sometimes:
[ 6412.954721] RPM wakelock ref not held during HW access
[ 6412.954795] WARNING: CPU: 7 PID: 11941 at
linux/drivers/gpu/drm/i915/intel_drv.h:1800
intel_uncore_forcewake_get.part.7+0x96/0xa0 [i915]
[ 6412.954915] Call Trace:
[ 6412.954951] intel_uncore_forcewake_get+0x18/0x20 [i915]
[ 6412.954989] intel_gvt_switch_mmio+0x8e/0x770 [i915]
[ 6412.954996] ? __slab_free+0x14d/0x2c0
[ 6412.955001] ? __slab_free+0x14d/0x2c0
[ 6412.955006] ? __slab_free+0x14d/0x2c0
[ 6412.955041] intel_vgpu_stop_schedule+0x92/0xd0 [i915]
[ 6412.955073] intel_gvt_deactivate_vgpu+0x48/0x60 [i915]
[ 6412.955078] __intel_vgpu_release+0x55/0x260 [kvmgt]
when this happens, gvt_switch_mmio is called at vgpu destroy, host i915 is
idle and doesn't hold RPM wakelock, igd is in powersave mode, but
gvt_switch_mmio require igd power on to access register, so
intel_runtime_pm_get should be added to make sure igd power on before
gvt_switch_mmio.
v2: Move runtime_pm_get/put into gvt_switch_mmio.(Zhenyu)
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
|
|
The ATMEL_ST config selects MFD_SYSCON, but does not depend on HAS_IOMEM.
Compile testing on architecture without HAS_IOMEM causes "unmet direct
dependencies" in Kconfig phase. Detected by "make ARCH=score allyesconfig".
Add the proper dependency to the ATMEL_ST config.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/1520335233-11277-1-git-send-email-yamada.masahiro@socionext.com
|
|
When running rcutorture with TREE03 config, CONFIG_PROVE_LOCKING=y, and
kernel cmdline argument "rcutorture.gp_exp=1", lockdep reports a
HARDIRQ-safe->HARDIRQ-unsafe deadlock:
================================
WARNING: inconsistent lock state
4.16.0-rc4+ #1 Not tainted
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
takes:
__schedule+0xbe/0xaf0
{IN-HARDIRQ-W} state was registered at:
_raw_spin_lock+0x2a/0x40
scheduler_tick+0x47/0xf0
...
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&rq->lock);
<Interrupt>
lock(&rq->lock);
*** DEADLOCK ***
1 lock held by rcu_torture_rea/724:
rcu_torture_read_lock+0x0/0x70
stack backtrace:
CPU: 2 PID: 724 Comm: rcu_torture_rea Not tainted 4.16.0-rc4+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
Call Trace:
lock_acquire+0x90/0x200
? __schedule+0xbe/0xaf0
_raw_spin_lock+0x2a/0x40
? __schedule+0xbe/0xaf0
__schedule+0xbe/0xaf0
preempt_schedule_irq+0x2f/0x60
retint_kernel+0x1b/0x2d
RIP: 0010:rcu_read_unlock_special+0x0/0x680
? rcu_torture_read_unlock+0x60/0x60
__rcu_read_unlock+0x64/0x70
rcu_torture_read_unlock+0x17/0x60
rcu_torture_reader+0x275/0x450
? rcutorture_booster_init+0x110/0x110
? rcu_torture_stall+0x230/0x230
? kthread+0x10e/0x130
kthread+0x10e/0x130
? kthread_create_worker_on_cpu+0x70/0x70
? call_usermodehelper_exec_async+0x11a/0x150
ret_from_fork+0x3a/0x50
This happens with the following even sequence:
preempt_schedule_irq();
local_irq_enable();
__schedule():
local_irq_disable(); // irq off
...
rcu_note_context_switch():
rcu_note_preempt_context_switch():
rcu_read_unlock_special():
local_irq_save(flags);
...
raw_spin_unlock_irqrestore(...,flags); // irq remains off
rt_mutex_futex_unlock():
raw_spin_lock_irq();
...
raw_spin_unlock_irq(); // accidentally set irq on
<return to __schedule()>
rq_lock():
raw_spin_lock(); // acquiring rq->lock with irq on
which means rq->lock becomes a HARDIRQ-unsafe lock, which can cause
deadlocks in scheduler code.
This problem was introduced by commit 02a7c234e540 ("rcu: Suppress
lockdep false-positive ->boost_mtx complaints"). That brought the user
of rt_mutex_futex_unlock() with irq off.
To fix this, replace the *lock_irq() in rt_mutex_futex_unlock() with
*lock_irq{save,restore}() to make it safe to call rt_mutex_futex_unlock()
with irq off.
Fixes: 02a7c234e540 ("rcu: Suppress lockdep false-positive ->boost_mtx complaints")
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20180309065630.8283-1-boqun.feng@gmail.com
|
|
Disable the kprobe probing of the entry trampoline:
.entry_trampoline is a code area that is used to ensure page table
isolation between userspace and kernelspace.
At the beginning of the execution of the trampoline, we load the
kernel's CR3 register. This has the effect of enabling the translation
of the kernel virtual addresses to physical addresses. Before this
happens most kernel addresses can not be translated because the running
process' CR3 is still used.
If a kprobe is placed on the trampoline code before that change of the
CR3 register happens the kernel crashes because int3 handling pages are
not accessible.
To fix this, add the .entry_trampoline section to the kprobe blacklist
to prohibit the probing of code before all the kernel pages are
accessible.
Signed-off-by: Francis Deslauriers <francis.deslauriers@efficios.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: mathieu.desnoyers@efficios.com
Cc: mhiramat@kernel.org
Link: http://lkml.kernel.org/r/1520565492-4637-2-git-send-email-francis.deslauriers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In ctx_resched(), EVENT_FLEXIBLE should be sched_out when EVENT_PINNED is
added. However, ctx_resched() calculates ctx_event_type before checking
this condition. As a result, pinned events will NOT get higher priority
than flexible events.
The following shows this issue on an Intel CPU (where ref-cycles can
only use one hardware counter).
1. First start:
perf stat -C 0 -e ref-cycles -I 1000
2. Then, in the second console, run:
perf stat -C 0 -e ref-cycles:D -I 1000
The second perf uses pinned events, which is expected to have higher
priority. However, because it failed in ctx_resched(). It is never
run.
This patch fixes this by calculating ctx_event_type after re-evaluating
event_type.
Reported-by: Ephraim Park <ephiepark@fb.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <jolsa@redhat.com>
Cc: <kernel-team@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 487f05e18aa4 ("perf/core: Optimize event rescheduling on active contexts")
Link: http://lkml.kernel.org/r/20180306055504.3283731-1-songliubraving@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull NVMe fixes for this series from Keith:
"A few late fixes for 4.16:
* Reverting sysfs slave device links for native nvme multipathing.
The hidden disk attributes broke common user tools.
* A fix for a PPC pci error handling regression.
* Update pci interrupt count to consider the actual IRQ spread, fixing
potentially poor initial queue affinity.
* Off-by-one errors in nvme-fc queue sizes
* A fabrics discovery fix to be more tolerant with user tools."
* 'nvme-4.16-rc5' of git://git.infradead.org/nvme:
nvme_fc: rework sqsize handling
nvme-fabrics: Ignore nr_io_queues option for discovery controllers
Revert "nvme: create 'slaves' and 'holders' entries for hidden controllers"
nvme: pci: pass max vectors as num_possible_cpus() to pci_alloc_irq_vectors
nvme-pci: Fix EEH failure on ppc
|
|
into drm-fixes
Fixes for 4.16. A bit bigger than I would have liked, but most of that
is DC fixes which Harry helped me pull together from the past few weeks.
Highlights:
- Fix DL DVI with DC
- Various RV fixes for DC
- Overlay fixes for DC
- Fix HDMI2 handling on boards without HBR tables in the vbios
- Fix crash with pass-through on SI on amdgpu
- Fix RB harvesting on KV
- Fix hibernation failures on UVD with certain cards
* 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux: (35 commits)
drm/amd/display: validate plane format on primary plane
drm/amdgpu:Always save uvd vcpu_bo in VM Mode
drm/amdgpu:Correct max uvd handles
drm/amd/display: early return if not in vga mode in disable_vga
drm/amd/display: Fix takover from VGA mode
drm/amd/display: Fix memleaks when atomic check fails.
drm/amd/display: Return success when enabling interrupt
drm/amd/display: Use crtc enable/disable_vblank hooks
drm/amd/display: update infoframe after dig fe is turned on
drm/amd/display: fix boot-up on vega10
drm/amd/display: fix cursor related Pstate hang
drm/amd/display: Set irq state only on existing crtcs
drm/amd/display: Fixed non-native modes not lighting up
drm/amd/display: Call update_stream_signal directly from amdgpu_dm
drm/amd/display: Make create_stream_for_sink more consistent
drm/amd/display: Don't block dual-link DVI modes
drm/amd/display: Don't allow dual-link DVI on all ASICs.
drm/amd/display: Pass signal directly to enable_tmds_output
drm/amd/display: Remove unnecessary fail labels in create_stream_for_sink
drm/amd/display: Move MAX_TMDS_CLOCK define to header
...
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
sun4i fixes on clk, division by zero and LVDS.
* tag 'drm-misc-fixes-2018-03-07' of git://anongit.freedesktop.org/drm/drm-misc:
drm/sun4i: crtc: Call drm_crtc_vblank_on / drm_crtc_vblank_off
drm/sun4i: rgb: Fix potential division by zero
drm/sun4i: tcon: Reduce the scope of the LVDS error a bit
drm/sun4i: Release exclusive clock lock when disabling TCON
drm/sun4i: Fix dclk_set_phase
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- 2 fixes: 1 for perf and 1 execlist submission race.
* tag 'drm-intel-fixes-2018-03-07' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Suspend submission tasklets around wedging
drm/i915/perf: fix perf stream opening lock
|
|
This patch adds support for r8a77965 (R-Car M3-N).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
"A miscellaneous pile of MIPS fixes for 4.16:
- move put_compat_sigset() to evade hardened usercopy warnings (4.16)
- select ARCH_HAVE_PC_{SERIO,PARPORT} for Loongson64 platforms (4.16)
- fix kzalloc() failure handling in ath25 (3.19) and Octeon (4.0)
- fix disabling of IPIs during BMIPS suspend (3.19)"
* tag 'mips_fixes_4.16_4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: BMIPS: Do not mask IPIs during suspend
MIPS: Loongson64: Select ARCH_MIGHT_HAVE_PC_SERIO
MIPS: Loongson64: Select ARCH_MIGHT_HAVE_PC_PARPORT
signals: Move put_compat_sigset to compat.h to silence hardened usercopy
MIPS: OCTEON: irq: Check for null return on kzalloc allocation
MIPS: ath25: Check for kzalloc allocation failure
|
|
This USB-SATA controller seems to be similar with JMicron bridge
152d:2566 already on the list. Adding it here fixes "Invalid
field in cdb" errors.
Signed-off-by: Teijo Kinnunen <teijo.kinnunen@code-q.fi>
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform fix from Benson Leung:
"Revert a problematic patch that constified something imporperly"
* tag 'chrome-platform-4.16-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
Revert "platform/chrome: chromeos_laptop: make chromeos_laptop const"
|
|
We do want to respect the FLUSH_SYNC argument to nfs_commit_inode() to
ensure that all outstanding COMMIT requests to the inode in question are
complete. Currently we may exit early from both nfs_commit_inode() and
nfs_write_inode() even if there are COMMIT requests in flight, or unstable
writes on the commit list.
In order to get the right semantics w.r.t. sync_inode(), we don't need
to have nfs_commit_inode() reset the inode dirty flags when called from
nfs_wb_page() and/or nfs_wb_all(). We just need to ensure that
nfs_write_inode() leaves them in the right state if there are outstanding
commits, or stable pages.
Reported-by: Scott Mayhew <smayhew@redhat.com>
Fixes: dc4fd9ab01ab ("nfs: don't wait on commit in nfs_commit_inode()...")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Ensure that we hold a reference to the layout header when processing
the pNFS return-on-close so that the refcount value does not inadvertently
go to zero.
Reported-by: Tigran Mkrtchyan <tigran.mkrtchyan@desy.de>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org # v4.10+
Tested-by: Tigran Mkrtchyan <tigran.mkrtchyan@desy.de>
|
|
The start offset needs to be of type loff_t.
Fixed: 5fadeb47dcc5c ("nfs: count DIO good bytes correctly with mirroring")
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Corrected four outstanding issues in the transport around sqsize.
1: Create Connection LS is sending the 1's-based sqsize, should be
sending the 0's-based value.
2: allocation of hw queue is using the 0's-base size. It should be
using the 1's-based value.
3: normalization of ctrl.sqsize by MQES is using MQES+1 (1's-based
value). It should be MQES (0's-based value).
4: Missing clause to ensure queue_count not larger than ctrl->sqsize.
Corrected by:
Clean up routines that pass queue size around. The queue size value is
the actual count (1's-based) value and determined from ctrl->sqsize + 1.
Routines that send 0's-based value adapt from queue size.
Sset ctrl->sqsize properly for MQES.
Added clause to nsure queue_count not larger than ctrl->sqsize + 1.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <keith.busch@intel.com>
|
|
The xHCI DbC implementation might enter a deadlock situation because
there is no sufficient protection against the shared data between
process and softirq contexts. This can lead to the following lockdep
warnings. This patch changes to use spin_{,un}lock_irq{save,restore}
to avoid potential deadlock.
[ 528.248084] ================================
[ 528.252914] WARNING: inconsistent lock state
[ 528.257756] 4.15.0-rc1+ #1630 Not tainted
[ 528.262305] --------------------------------
[ 528.267145] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 528.273953] ksoftirqd/1/17 [HC0[0]:SC1[1]:HE0:SE0] takes:
[ 528.280075] (&(&port->port_lock)->rlock){+.?.}, at: [<ffffffff815396a8>] dbc_rx_push+0x38/0x1c0
[ 528.290043] {SOFTIRQ-ON-W} state was registered at:
[ 528.295570] _raw_spin_lock+0x2f/0x40
[ 528.299818] dbc_write_complete+0x27/0xa0
[ 528.304458] xhci_dbc_giveback+0xd1/0x200
[ 528.309098] xhci_dbc_flush_endpoint_requests+0x50/0x70
[ 528.315116] xhci_dbc_handle_events+0x696/0x7b0
[ 528.320349] process_one_work+0x1ee/0x6e0
[ 528.324988] worker_thread+0x4a/0x430
[ 528.329236] kthread+0x13e/0x170
[ 528.332992] ret_from_fork+0x24/0x30
[ 528.337141] irq event stamp: 2861
[ 528.340897] hardirqs last enabled at (2860): [<ffffffff810674ea>] tasklet_action+0x6a/0x250
[ 528.350460] hardirqs last disabled at (2861): [<ffffffff817dc1ef>] _raw_spin_lock_irq+0xf/0x40
[ 528.360219] softirqs last enabled at (2852): [<ffffffff817e0e8c>] __do_softirq+0x3dc/0x4f9
[ 528.369683] softirqs last disabled at (2857): [<ffffffff8106805b>] run_ksoftirqd+0x1b/0x60
[ 528.379048]
[ 528.379048] other info that might help us debug this:
[ 528.386443] Possible unsafe locking scenario:
[ 528.386443]
[ 528.393150] CPU0
[ 528.395917] ----
[ 528.398687] lock(&(&port->port_lock)->rlock);
[ 528.403821] <Interrupt>
[ 528.406786] lock(&(&port->port_lock)->rlock);
[ 528.412116]
[ 528.412116] *** DEADLOCK ***
[ 528.412116]
[ 528.418825] no locks held by ksoftirqd/1/17.
[ 528.423662]
[ 528.423662] stack backtrace:
[ 528.428598] CPU: 1 PID: 17 Comm: ksoftirqd/1 Not tainted 4.15.0-rc1+ #1630
[ 528.436387] Call Trace:
[ 528.439158] dump_stack+0x5e/0x8e
[ 528.442914] print_usage_bug+0x1fc/0x220
[ 528.447357] mark_lock+0x4db/0x5a0
[ 528.451210] __lock_acquire+0x726/0x1130
[ 528.455655] ? __lock_acquire+0x557/0x1130
[ 528.460296] lock_acquire+0xa2/0x200
[ 528.464347] ? dbc_rx_push+0x38/0x1c0
[ 528.468496] _raw_spin_lock_irq+0x35/0x40
[ 528.473038] ? dbc_rx_push+0x38/0x1c0
[ 528.477186] dbc_rx_push+0x38/0x1c0
[ 528.481139] tasklet_action+0x1d2/0x250
[ 528.485483] __do_softirq+0x1dc/0x4f9
[ 528.489630] run_ksoftirqd+0x1b/0x60
[ 528.493682] smpboot_thread_fn+0x179/0x270
[ 528.498324] kthread+0x13e/0x170
[ 528.501981] ? sort_range+0x20/0x20
[ 528.505933] ? kthread_delayed_work_timer_fn+0x80/0x80
[ 528.511755] ret_from_fork+0x24/0x30
Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix incorrent values showed for max Primary stream and
Linear stream array (LSA) values in the endpoint context
decoder.
Fixes: 19a7d0d65c4a ("usb: host: xhci: add Slot and EP Context tracers")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds missing initialisation for HP 2013 UltraSlim Dock
Line-In/Out PINs and activates keyboard mute/micmute leds
for HP ProBook 640 G2
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds missing initialisation for HP 2013 UltraSlim Dock
Line-In/Out PINs and activates keyboard mute/micmute leds
for HP EliteBook 820 G3
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus
Pull a xen_blkfront fix from Konrad:
"It has one simple fix for the multi-queue support not showing up after
a block device was detached/re-attached."
* 'stable/for-jens-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen-blkfront: move negotiate_mq to cover all cases of new VBDs
|
|
This removes a dependency on the order options are passed when creating
a fabrics controller. With the old code, if "nr_io_queues" appears before
an "nqn" option specifying the discovery controller, then nr_io_queues
is overridden with zero. If "nr_io_queues" appears after specifying the
discovery controller, then the nr_io_queues option is used to set the
number of queues, and the driver attempts to establish IO connections
to the discovery controller (which doesn't work).
It seems better to ignore (and warn about) the "nr_io_queues" option
if userspace has already asked to connect to the discovery controller.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
|
|
cmd_dt_S_dtb constructs the assembly source to incorporate a devicetree
FDT (that is, the .dtb file) as binary data in the kernel image. This
assembly source contains labels before and after the binary data. The
label names incorporate the file name of the corresponding .dtb file.
Hyphens are not legal characters in labels, so .dtb files built into the
kernel with hyphens in the file name result in errors like the
following:
bcm3368-netgear-cvg834g.dtb.S: Assembler messages:
bcm3368-netgear-cvg834g.dtb.S:5: Error: : no such section
bcm3368-netgear-cvg834g.dtb.S:5: Error: junk at end of line, first unrecognized character is `-'
bcm3368-netgear-cvg834g.dtb.S:6: Error: unrecognized opcode `__dtb_bcm3368-netgear-cvg834g_begin:'
bcm3368-netgear-cvg834g.dtb.S:8: Error: unrecognized opcode `__dtb_bcm3368-netgear-cvg834g_end:'
bcm3368-netgear-cvg834g.dtb.S:9: Error: : no such section
bcm3368-netgear-cvg834g.dtb.S:9: Error: junk at end of line, first unrecognized character is `-'
Fix this by updating cmd_dt_S_dtb to transform all hyphens from the file
name to underscores when constructing the labels.
As of v4.16-rc2, 1139 .dts files across ARM64, ARM, MIPS and PowerPC
contain hyphens in their names, but the issue only currently manifests
on Broadcom MIPS platforms, as that is the only place where such files
are built into the kernel. For example when CONFIG_DT_NETGEAR_CVG834G=y,
or on BMIPS kernels when the dtbs target is used (in the latter case it
admittedly shouldn't really build all the dtb.o files, but thats a
separate issue).
Fixes: 695835511f96 ("MIPS: BMIPS: rename bcm96358nb4ser to bcm6358-neufbox4-sercom")
Signed-off-by: James Hogan <jhogan@kernel.org>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The bloat-o-meter script has two typos in the help, fix both.
Fixes: 192efb7a1f9b ("bloat-o-meter: provide 3 different arguments for data, function and All")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.16-rc4
Just small fixes now. The two most important are a fix for a a lock up
on USB ID pin change during system suspend/resume on dwc3 and a
use-after-free fix in ffs_fs_kill_sb().
Apart from that, some DT compatible fixes.
|
|
The check_interval file in
/sys/devices/system/machinecheck/machinecheck<cpu number>
directory is a global timer value for MCE polling. If it is changed by one
CPU, mce_restart() broadcasts the event to other CPUs to delete and restart
the MCE polling timer and __mcheck_cpu_init_timer() reinitializes the
mce_timer variable.
If more than one CPU writes a specific value to the check_interval file
concurrently, mce_timer is not protected from such concurrent accesses and
all kinds of explosions happen. Since only root can write to those sysfs
variables, the issue is not a big deal security-wise.
However, concurrent writes to these configuration variables is void of
reason so the proper thing to do is to serialize the access with a mutex.
Boris:
- Make store_int_with_restart() use device_store_ulong() to filter out
negative intervals
- Limit min interval to 1 second
- Correct locking
- Massage commit message
Signed-off-by: Seunghun Han <kkamagui@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180302202706.9434-1-kkamagui@gmail.com
|
|
Updating microcode used to be relatively rare. Now that it has become
more common we should save the microcode version in a machine check
record to make sure that those people looking at the error have this
important information bundled with the rest of the logged information.
[ Borislav: Simplify a bit. ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180301233449.24311-1-tony.luck@intel.com
|
|
Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
One version of Lenovo Thinkpad T570 did not use ALC298
(like other Kaby Lake devices). Instead it uses ALC292.
In order to make the Lenovo dock working with that codec
the dock quirk for ALC292 will be used.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
s/visinble/visible/
Signed-off-by: Seunghun Han <kkamagui@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1520397135-132809-1-git-send-email-kkamagui@gmail.com
|
|
With the previous two fixes for the write / ioctl races:
ALSA: seq: Don't allow resizing pool in use
ALSA: seq: More protection for concurrent write and ioctl races
the cells aren't any longer in queues at the point calling
snd_seq_pool_done() in snd_seq_ioctl_set_client_pool(). Hence the
function call snd_seq_queue_client_leave_cells() can be dropped safely
from there.
Suggested-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch is an attempt for further hardening against races between
the concurrent write and ioctls. The previous fix d15d662e89fc
("ALSA: seq: Fix racy pool initializations") covered the race of the
pool initialization at writer and the pool resize ioctl by the
client->ioctl_mutex (CVE-2018-1000004). However, basically this mutex
should be applied more widely to the whole write operation for
avoiding the unexpected pool operations by another thread.
The only change outside snd_seq_write() is the additional mutex
argument to helper functions, so that we can unlock / relock the given
mutex temporarily during schedule() call for blocking write.
Fixes: d15d662e89fc ("ALSA: seq: Fix racy pool initializations")
Reported-by: 范龙飞 <long7573@126.com>
Reported-by: Nicolai Stange <nstange@suse.de>
Reviewed-and-tested-by: Nicolai Stange <nstange@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Original idea by Ashok, completely rewritten by Borislav.
Before you read any further: the early loading method is still the
preferred one and you should always do that. The following patch is
improving the late loading mechanism for long running jobs and cloud use
cases.
Gather all cores and serialize the microcode update on them by doing it
one-by-one to make the late update process as reliable as possible and
avoid potential issues caused by the microcode update.
[ Borislav: Rewrite completely. ]
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: https://lkml.kernel.org/r/20180228102846.13447-8-bp@alien8.de
|
|
... so that any newer version can land in the cache and can later be
fished out by the application functions. Do that before grabbing the
hotplug lock.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: https://lkml.kernel.org/r/20180228102846.13447-7-bp@alien8.de
|
|
The cache might contain a newer patch - look in there first.
A follow-on change will make sure newest patches are loaded into the
cache of microcode patches.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: https://lkml.kernel.org/r/20180228102846.13447-6-bp@alien8.de
|
|
Avoid loading microcode if any of the CPUs are offline, and issue a
warning. Having different microcode revisions on the system at any time
is outright dangerous.
[ Borislav: Massage changelog. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: http://lkml.kernel.org/r/1519352533-15992-4-git-send-email-ashok.raj@intel.com
Link: https://lkml.kernel.org/r/20180228102846.13447-5-bp@alien8.de
|
|
Updating microcode is less error prone when caches have been flushed and
depending on what exactly the microcode is updating. For example, some
of the issues around certain Broadwell parts can be addressed by doing a
full cache flush.
[ Borislav: Massage it and use native_wbinvd() in both cases. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: http://lkml.kernel.org/r/1519352533-15992-3-git-send-email-ashok.raj@intel.com
Link: https://lkml.kernel.org/r/20180228102846.13447-4-bp@alien8.de
|
|
After updating microcode on one of the threads of a core, the other
thread sibling automatically gets the update since the microcode
resources on a hyperthreaded core are shared between the two threads.
Check the microcode revision on the CPU before performing a microcode
update and thus save us the WRMSR 0x79 because it is a particularly
expensive operation.
[ Borislav: Massage changelog and coding style. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: http://lkml.kernel.org/r/1519352533-15992-2-git-send-email-ashok.raj@intel.com
Link: https://lkml.kernel.org/r/20180228102846.13447-3-bp@alien8.de
|
|
It is a useless remnant from earlier times. Use the ucode_state enum
directly.
No functional change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com>
Link: https://lkml.kernel.org/r/20180228102846.13447-2-bp@alien8.de
|
|
As:
1) It's known that hypervisors lie about the environment anyhow (host
mismatch)
2) Even if the hypervisor (Xen, KVM, VMWare, etc) provided a valid
"correct" value, it all gets to be very murky when migration happens
(do you provide the "new" microcode of the machine?).
And in reality the cloud vendors are the ones that should make sure that
the microcode that is running is correct and we should just sing lalalala
and trust them.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
Cc: kvm <kvm@vger.kernel.org>
Cc: Krčmář <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180226213019.GE9497@char.us.oracle.com
|
|
This is a fix for a (sort of) fallout in the recent commit
d15d662e89fc ("ALSA: seq: Fix racy pool initializations") for
CVE-2018-1000004.
As the pool resize deletes the existing cells, it may lead to a race
when another thread is writing concurrently, eventually resulting a
UAF.
A simple workaround is not to allow the pool resizing when the pool is
in use. It's an invalid behavior in anyway.
Fixes: d15d662e89fc ("ALSA: seq: Fix racy pool initializations")
Reported-by: 范龙飞 <long7573@126.com>
Reported-by: Nicolai Stange <nstange@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since Linux v3.2, vsyscalls have been deprecated and slow. From v3.2
on, Linux had three vsyscall modes: "native", "emulate", and "none".
"emulate" is the default. All known user programs work correctly in
emulate mode, but vsyscalls turn into page faults and are emulated.
This is very slow. In "native" mode, the vsyscall page is easily
usable as an exploit gadget, but vsyscalls are a bit faster -- they
turn into normal syscalls. (This is in contrast to vDSO functions,
which can be much faster than syscalls.) In "none" mode, there are
no vsyscalls.
For all practical purposes, "native" was really just a chicken bit
in case something went wrong with the emulation. It's been over six
years, and nothing has gone wrong. Delete it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Kernel Hardening <kernel-hardening@lists.openwall.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/519fee5268faea09ae550776ce969fa6e88668b0.1520449896.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
