| Age | Commit message (Collapse) | Author |
|---|
|
All MXS users have been converted to device tree and the board files have
been removed.
No need to keep platform data in the driver.
Also move bus_width declaration in the beggining of mxs_mmc_probe() to
avoid: 'warning: ISO C90 forbids mixed declarations and code'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Before this patch, we always used only single sg entry for SDIO transfer.
This patch switches to using multiple sg entries. In the case of dwmci,
it supports only up to 4KB size per single sg entry. So if we want to
transfer more than 4KB, we should send more than 1 command.
When we tested before applying this patch, it took around 335 us for
5K(5120) bytes transfer with dwmci controller. After applying this patch,
it takes 242 us for 5K bytes. So this patch makes around 38% performance
improvement for 5K bytes transfer. If the transfer size is bigger, then
the performance improvement ratio will be increased.
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The patch "dw_mmc: fix multiple drv_data NULL dereferences" has
unfortunately clashed with my "mmc: dw_mmc: constify dw_mci_idmac_ops
in exynos back-end" patch, causing new warnings to appear.
This should hopefully fix the issue for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The at91-mci driver is not needed anymore since the atmel-mci driver now
supports all Atmel devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
MMC debounce clock is applicable only for omap2430, warning message gets
printed when enable fails for debounce clock. Remove the get debounce clock
failure message as it is noisy for other platforms.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Maximum bus frequency can be limited by external circuitry like level
shifters etc. Allow passing this value from DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This allows DT-driven board to set up the pin mux only when the driver
is in use.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When a SD card is initialized some data transfers of 64 and 8 bytes
are issued. It seems the DMA has some problems dealing with these kind
of "short" transfers, leading sometimes to the SD card not being detected.
In order to solve this problem, do not use DMA for transfer sizes lower
than the sector size.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Since v3.2 we have nice macro to define the platform driver's init and exit
calls. This patch simplifies the dw_mmc platform driver by using that macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Girish K S <girish.shivanajappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In case both 'req' and 'mq->mqrq_prev->req' are null, there is no request
to be processed. That means there is no need to switch buffer.
Switching buffer is required only after finishing 'issue_fn'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On some systems, e.g., kzm9g, MMCIF interfaces can produce spurious
interrupts without any active request. To prevent the Oops, that results
in such cases, don't dereference the mmc request pointer until we make
sure, that we are indeed processing such a request.
Reported-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The vmmc regulator enable in sdhci_add_host is NOT necessary since
it can be enabled during mmc_power_up by function mmc_regulator_set_ocr.
And this extra enable will make regulator_enable/regulator_disable
unbalanced. Consequently, vmmc can't be disabled during mmc_power_off.
Also, if the vqmmc regulator exists, it should be enabled regardless it
support 1.8v or not.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This reverts commit 8464dd52d3198dd05, which was a misapplied debugging
version of the patch, not the final patch itself.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: stable@vger.kernel.org
|
|
2abeb5c5ded2 ("Add clk_(enable/disable) in runtime suspend/resume")
added the capability to stop the clocks when the device is runtime
suspended, but forgot to handle the case of the card-detect using
an external gpio.
Therefore in the case that runtime-pm is enabled, start the io-clock
when a card is inserted and stop it again once it is removed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
in cgroup_add_file,when creating files for cgroup,
some of creation may be skipped. So we need to avoid
deleting these uncreated files in cgroup_rm_file,
otherwise the warning msg will be triggered.
"cgroup_addrm_files: failed to remove memory_pressure_enabled, err=-2"
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@redhat.com>
Cc: stable@vger.kernel.org
|
|
Pull MIPS fixes from Ralf Baechle:
"These are the fixes for the N32 syscall bugs found by Al, an
extraneous break that broke detection for R3000 and R3081 processors,
an endless loop processing signals for kernel task (x86 received the
same fix a while ago) and a fix for transparent huge page which took
ages to track down because it was so hard to come up with a workable
test case."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix endless loop when processing signals for kernel tasks
MIPS: R3000/R3081: Fix CPU detection.
MIPS: N32: Fix signalfd4 syscall entry point
MIPS: N32: Fix preadv(2) and pwritev(2) entry points.
MIPS: Avoid mcheck by flushing page range in huge_ptep_set_access_flags()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull build fix from Rusty Russell:
"Tim Gardner <tim.gardner@canonical.com> writes:
> It is $(obj)/oid_registry.o that is dependent on $(obj)/oid_registry_data.c.
> The object file cannot be built until $(obj)/oid_registry_data.c has been
> generated.
>
> A periodic and hard to reproduce parallel build failure is due to
> this incorrect lib/Makefile dependency. The compile error is completely
> disingenuous.
>
> GEN lib/oid_registry_data.c
> Compiling 49 OIDs
> CC lib/oid_registry.o
> gcc: error: lib/oid_registry.c: No such file or directory
> gcc: fatal error: no input files
> compilation terminated.
> make[3]: *** [lib/oid_registry.o] Error 4
I can't reproduce it either. It's completely weird; nothing ever
removes lib/oid_registry.c, so either gcc is giving the wrong message
or it's a weird fs with a very odd race.
But your version is definitely more correct than the previous one,
so..."
* 'more-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
lib/Makefile: Fix oid_registry build dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module signing fixes from Rusty Russell:
"David gave me these a month ago, during my git workflow churn :("
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
ASN.1: Fix an indefinite length skip error
MODSIGN: Don't use enum-type bitfields in module signature info block
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull watchdog fix from Thomas Gleixner:
"Trivial CPU hotplug regression fix for the watchdog code"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
watchdog: Fix CPU hotplug regression
|
|
The vmclear function will be assigned to the callback function pointer
when loading kvm-intel module. And the bitmap indicates whether we
should do VMCLEAR operation in kdump. The bits in the bitmap are
set/unset according to different conditions.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
|
|
This patch provides a way to VMCLEAR VMCSs related to guests
on all cpus before executing the VMXOFF when doing kdump. This
is used to ensure the VMCSs in the vmcore updated and
non-corrupted.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
|
|
The variable se_sess is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Zero copy TX has been around for a while now.
We seem to be down to eliminating theoretical bugs
and performance tuning at this point:
it's probably time to enable it by default so that
most users get the benefit.
Keep the flag around meanwhile so users can experiment
with disabling this if they experience regressions.
I expect that we will remove it in the future.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
For short packets zerocopy mode adds overhead
of managing heads which isn't necessary: we
could simly update used ring directly
same as with zerocopy disabled.
Things seem to run a bit faster if we detect
and bypass head management when zcopy isn't used.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
When memory map changes, we need to flush outstanding
DMAs as they might in theory reference old memory addresses.
To do this simply stop initiating new DMAs
and wait for ubufs ref count to drop to 0.
Afterwards reset the count back to 1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
vring changes already do a flush internally where appropriate, so we do
not need a second flush.
It's currently not very expensive but a follow-up patch makes flush more
heavy-weight, so remove the extra flush here to avoid regressing
performance if call or kick fds are changed on data path.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We do not allow old-style function definition. Always spell foo(void) if
a function does not take any parameters.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Support these transfer modes from the SPI layer by setting
the appropriate register bits before doing the transfer.
This was tested on the Marvell kirkwood SOC that uses this driver.
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The MSIOF hardware block is used in the SH Mobile series as well, so we
add it here.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
clk_get() no longer needs a character string for associating the right
clock as this is done via the device struct now.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
In order to avoid constantly allocating and deallocating there is a fixed
buffer which spi_write_then_read() uses for transfers, with an early error
check to ensure that the transfer fits within the buffer. This limits the
size of transfers to this size, currently max(32, SMP_CACHE_BYTES).
Since we can dynamically allocate and in fact already have a fallback
to do so when there is contention for the fixed buffer remove this
restriction and instead dynamically allocate a suitably sized buffer if
the transfer won't fit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This driver is obsolete and can't even be built anymore since the
platform it depends has been removed.
The STMP series is completely covered by the MXS platform these days, so
spi-mxs can be used instead.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc.git
Pull in the changes Mark has queued up for SPI
|
|
The Kconfig currently enables MSDOS partitions by default because they
are assumed to be essential, but it's necessary to enable "advanced
partition selection" in order to get GPT support. IMO GPT partitions
are becoming common enought to deserve the same treatment MSDOS
partitions get.
(Side note: I got bit by a disk that had MSDOS and GPT partition
tables, but for some reason the MSDOS table was different from the
GPT one. I was stupid enought to disable "advanced partition
selection" in my .config, which disabled GPT partitioning and made
my btrfs pool unbootable because it couldn't find the partitions)
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The function bsg_goose_queue() does not have any in-tree callers,
so let's remove it.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some request_fn implementations, e.g. scsi_request_fn(), unlock
the queue lock internally. This may result in multiple threads
executing request_fn for the same queue simultaneously. Keep
track of the number of active request_fn calls and make sure that
blk_cleanup_queue() waits until all active request_fn invocations
have finished. A block driver may start cleaning up resources
needed by its request_fn as soon as blk_cleanup_queue() finished,
so blk_cleanup_queue() must wait for all outstanding request_fn
invocations to finish.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Chanho Min <chanho.min@lge.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Running a queue must continue after it has been marked dying until
it has been marked dead. So the function blk_run_queue_async() must
not schedule delayed work after blk_cleanup_queue() has marked a queue
dead. Hence add a test for that queue state in blk_run_queue_async()
and make sure that queue_unplugged() invokes that function with the
queue lock held. This avoids that the queue state can change after
it has been tested and before mod_delayed_work() is invoked. Drop
the queue dying test in queue_unplugged() since it is now
superfluous: __blk_run_queue() already tests whether or not the
queue is dead.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A block driver may start cleaning up resources needed by its
request_fn as soon as blk_cleanup_queue() finished, so request_fn
must not be invoked after draining finished. This is important
when blk_run_queue() is invoked without any requests in progress.
As an example, if blk_drain_queue() and scsi_run_queue() run in
parallel, blk_drain_queue() may have finished all requests after
scsi_run_queue() has taken a SCSI device off the starved list but
before that last function has had a chance to run the queue.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Chanho Min <chanho.min@lge.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Let the caller of blk_drain_queue() obtain the queue lock to improve
readability of the patch called "Avoid that request_fn is invoked on
a dead queue".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
QUEUE_FLAG_DEAD is used to indicate that queuing new requests must
stop. After this flag has been set queue draining starts. However,
during the queue draining phase it is still safe to invoke the
queue's request_fn, so QUEUE_FLAG_DYING is a better name for this
flag.
This patch has been generated by running the following command
over the kernel source tree:
git grep -lEw 'blk_queue_dead|QUEUE_FLAG_DEAD' |
xargs sed -i.tmp -e 's/blk_queue_dead/blk_queue_dying/g' \
-e 's/QUEUE_FLAG_DEAD/QUEUE_FLAG_DYING/g'; \
sed -i.tmp -e "s/QUEUE_FLAG_DYING$(printf \\t)*5/QUEUE_FLAG_DYING$(printf \\t)5/g" \
include/linux/blkdev.h; \
sed -i.tmp -e 's/ DEAD/ DYING/g' -e 's/dead queue/a dying queue/' \
-e 's/Dead queue/A dying queue/' block/blk-core.c
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Before queuing the flip but crucially after attaching the unpin-work to
the crtc, we continue to setup the unpin-work. However, should the
hardware fire early, we see the connected unpin-work and queue the task.
The task then promptly runs and unpins the fb before we finish taking
the required references or even pinning it... Havoc.
To close the race, we use the flip-pending atomic to indicate when the
flip is finally setup and enqueued. So during the flip-done processing,
we can check more accurately whether the flip was expected.
v2: Add the appropriate mb() to ensure that the writes to the page-flip
worker are complete prior to marking it active and emitting the MI_FLIP.
On the read side, the mb should be enforced by the spinlocks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Review the barriers a bit, we need a write barrier both
before and after updating ->pending. Similarly we need a read barrier
in the interrupt handler both before and after reading ->pending. With
well-ordered irqs only one barrier in each place should be required,
but since this patch explicitly sets out to combat spurious interrupts
with is staged activation of the unpin work we need to go full-bore on
the barriers, too. Discussed with Chris Wilson on irc and changes
acked by him.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the sdata work is pending while the interface is stopped,
we currently flush it. If it's not running this means waiting
for it to run, which could take a while if the workqueue is
backlogged. However, the work exits right away if it starts
to run while the interface is already stopping. There's no
point in waiting for that, so use cancel_work_sync() instead.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is really a 3-bit field, not a single bit,
so declare a mask and shift. Also fix hwsim, it
advertises the maximum possible.
While at it reindent all the defines using tabs
instead of spaces.
Change-Id: I7cd81c0d72f76deb5010aba5bfa3dd312006e898
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Previously, mesh peering frames from a STA without a station
entry were being dropped.
Mesh Peering Open and other frames (WLAN_CATEGORY_SELF_PROTECTED)
are valid mesh peering frames even if received from a yet unknown
station; the STA entry will be created in mesh_peer_init later.
The problem didn't occur previously since both STAs receive each
other's beacons which created the STA entry. However, this causes
an unnecessary delay and beacons might not be received if either
node is in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ret_count has to be at least 3, as we have to count the 2 bytes that are used
for the size of the reply. Without this, memcpy() might be called with zero or
negative count.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The previous memcpy implementation relied on the size advertized by the
device. There were no guarantees that buf was big enough.
Some gymnastic is also required with the +2/-2 to take into account
the first 2 bytes of the returned buffer where the total returned
length is supplied by the device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
There is no point in keeping the irq in i2c_hid as it's already
there in client.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
