| Age | Commit message (Collapse) | Author |
|---|
|
The cursor size also affects the register programming.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We were storing viewport relative coordinates. However, crtc_cursor_set2
and cursor_reset pass amdgpu_crtc->cursor_x/y as the x/y parameters of
cursor_move_locked, which would break if the CRTC isn't located at
(0, 0).
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
GUI idle interrupts should be enabled only after we
have enabled coarse grain clock gating (CGCG). This
prevents GFX engine generating idle interrupt even
though CGCG is not completely enabled.
Most of the time this goes un-noticed, but on some
Stoney ASICs this results in GFX engine hang after
system resumes from suspend. The issue is not
particular to Stoney though and could have occured
on any ASIC. The patch fixes this issue.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Sunil Uttarwar <Sunil.Uttarwar1@amd.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
VCE clocks are set to be disabled, when not in use.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
can't get uvd's state by uvd_enabled. uvd_enabled
is used for request higher mclk.
in multi-display case, mclk has been in highest clock,
no matter uvd's state changed, uvd_enabled will not
be changed.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Forget to check UCODE_ID_STORAGE case and will cause to print error
message when loading driver, correct it.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For virtualization, firmware loading need the firmware version info,
and will load the right firmware. So, transfer fw_version to toc.
Signed-off-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
the root cause is we gate the clock to uvd vcpu.
mclk's change should need the response from uvd if
it is power on.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's per queue not per pipe.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
in amdgpu"
This reverts commit a693e050edfe794fea81d7cfe72429a406aa380b.
This breaks on systems with huge amounts of system memory as we do not have
enough vram to store the page tables. Additionally, this is less of an issue
with the recent gtt manager changes.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
I noticed some wakeirq flakeyness with consumer drivers not using
autosuspend. For drivers not using autosuspend, the wakeirq may never
get unmasked in rpm_suspend() because of irq desc->depth.
We are configuring dedicated wakeirqs to start with IRQ_NOAUTOEN as we
naturally don't want them running until rpm_suspend() is called.
However, when a consumer driver initially calls pm_runtime_get(), we
now wrongly start with disable_irq_nosync() call on the dedicated
wakeirq that is disabled to start with.
This causes desc->depth to toggle between 1 and 2 instead of the usual
0 and 1. This can prevent enable_irq() from unmasking the wakeirq as
that only happens at desc->depth 1.
This does not necessarily show up with drivers using autosuspend as
there is time for disable_irq_nosync() before rpm_suspend() gets called
after the autosuspend timeout.
Let's fix the issue by adding wirq->status that lazily gets set on
the first rpm_suspend(). We also need PM runtime core private functions
for dev_pm_enable_wake_irq_check() and dev_pm_disable_wake_irq_check()
so we can enable the dedicated wakeirq on the first rpm_suspend().
While at it, let's also fix the comments for dev_pm_enable_wake_irq()
and dev_pm_disable_wake_irq(). Those can still be used by the consumer
drivers as needed because the IRQ core manages the interrupt usecount
for us.
Fixes: 4990d4fe327b (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are few 'else' keywords which are redundant in
acpi_os_get_root_pointer(). Refactor function to get rid of them.
While here, switch to pr_err() instead of printk(KERN_ERR ...).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is no need to override the error code returned by kstrtoul().
Propagate it directly to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Re-using idle state definition provided by arm,idle-state for domain
idle states creates a lot of confusion and limits further evolution of
the domain idle definition. To keep things clear and simple, define a
idle states for domain using a new compatible "domain-idle-state".
Fix existing PM domains code to look for the newly defined compatible.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This new expression allows us to refer to existing stateful objects from
rules.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Register a new quota stateful object type into the new stateful object
infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Register a new percpu counter stateful object type into the stateful
object infrastructure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch augments nf_tables to support stateful objects. This new
infrastructure allows you to create, dump and delete stateful objects,
that are identified by a user-defined name.
This patch adds the generic infrastructure, follow up patches add
support for two stateful objects: counters and quotas.
This patch provides a native infrastructure for nf_tables to replace
nfacct, the extended accounting infrastructure for iptables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
... so we can use current skb instead of working with a clone.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The caller assumes that < 0 means that skb was stolen (or free'd).
All other return values continue skb processing.
nf_hook_slow returns 3 different return value types:
A) a (negative) errno value: the skb was dropped (NF_DROP, e.g.
by iptables '-j DROP' rule).
B) 0. The skb was stolen by the hook or queued to userspace.
C) 1. all hooks returned NF_ACCEPT so the caller should invoke
the okfn so packet processing can continue.
nft ingress facility currently doesn't have the 'okfn' that
the NF_HOOK() macros use; there is no nfqueue support either.
So 1 means that nf_hook_ingress() caller should go on processing the skb.
In order to allow use of NF_STOLEN from ingress we need to translate
this to an errno number, else we'd crash because we continue with
already-free'd (or about to be free-d) skb.
The errno value isn't checked, its just important that its less than 0,
so return -1.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
I lost one test case in the last commit for xt_multiport.
For example, the rule is "-m multiport --dports 22,80,443".
When first port is unmatched and the second is matched, the curent codes
could not return the right result.
It would return false directly when the first port is unmatched.
Fixes: dd2602d00f80 ("netfilter: xt_multiport: Use switch case instead
of multiple condition checks")
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds a new flag that signals the kernel to update layer 4
checksum if the packet field belongs to the layer 4 pseudoheader. This
implicitly provides stateless NAT 1:1 that is useful under very specific
usecases.
Since rules mangling layer 3 fields that are part of the pseudoheader
may potentially convey any layer 4 packet, we have to deal with the
layer 4 checksum adjustment using protocol specific code.
This patch adds support for TCP, UDP and ICMPv6, since they include the
pseudoheader in the layer 4 checksum calculation. ICMP doesn't, so we
can skip it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Otherwise, if fib lookup fail, *dest will be filled with garbage value,
so reverse path filtering will not work properly:
# nft add rule x prerouting fib saddr oif eq 0 drop
Fixes: f6d0cbcf09c5 ("netfilter: nf_tables: add fib expression")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Acctually ntohl and htonl are identical, so this doesn't affect
anything, but it is conceptually wrong.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
instead of allocating each xt_counter individually, allocate 4k chunks
and then use these for counter allocation requests.
This should speed up rule evaluation by increasing data locality,
also speeds up ruleset loading because we reduce calls to the percpu
allocator.
As Eric points out we can't use PAGE_SIZE, page_allocator would fail on
arches with 64k page size.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Keeps some noise away from a followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
On SMP we overload the packet counter (unsigned long) to contain
percpu offset. Hide this from callers and pass xt_counters address
instead.
Preparation patch to allocate the percpu counters in page-sized batch
chunks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This is to facilitate converting from a singly-linked list to an array
of elements.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
During nfhook traversal we only need a very small subset of
nf_hook_ops members.
We need:
- next element
- hook function to call
- hook function priv argument
Bridge netfilter also needs 'thresh'; can be obtained via ->orig_ops.
nf_hook_entry struct is now 32 bytes on x86_64.
A followup patch will turn the run-time list into an array that only
stores hook functions plus their priv arguments, eliminating the ->next
element.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This allows easier future refactoring.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
nf_defrag modules for ipv4 and ipv6 export an empty stub function.
Any module that needs the defragmentation hooks registered simply 'calls'
this empty function to create a phony module dependency -- modprobe will
then load the defrag module too.
This extends netfilter ipv4/ipv6 defragmentation modules to delay the hook
registration until the functionality is requested within a network namespace
instead of module load time for all namespaces.
Hooks are only un-registered on module unload or when a namespace that used
such defrag functionality exits.
We have to use struct net for this as the register hooks can be called
before netns initialization here from the ipv4/ipv6 conntrack module
init path.
There is no unregister functionality support, defrag will always be
active once it was requested inside a net namespace.
The reason is that defrag has impact on nft and iptables rulesets
(without defrag we might see framents).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Passing zero for the size to vfio_find_dma() isn't compatible with
matching the start address of an existing vfio_dma. Doing so triggers a
corner case. In vfio_find_dma(), when the start address is equal to
dma->iova and size is 0, check for the end of search range makes it to
take wrong side of RB-tree. That fails the search even though the address
is present in mapped dma ranges.
In functions pin_pages and unpin_pages, the iova which is being searched
is base address of page to be pinned or unpinned. So here size should be
set to PAGE_SIZE, as argument to vfio_find_dma().
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Neo Jia <cjia@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Passing zero for the size to vfio_find_dma() isn't compatible with
matching the start address of an existing vfio_dma. Doing so triggers a
corner case. In vfio_find_dma(), when the start address is equal to
dma->iova and size is 0, check for the end of search range makes it to
take wrong side of RB-tree. That fails the search even though the address
is present in mapped dma ranges. Due to this, in vfio_dma_do_unmap(),
while checking boundary conditions, size should be set to 1 for verifying
start address of unmap range.
vfio_find_dma() is also used to verify last address in unmap range with
size = 0, but in that case address to be searched is calculated with
start + size - 1 and so it works correctly.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Neo Jia <cjia@nvidia.com>
[aw: changelog tweak]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
We now support nonblocking commits on drm_atomic_helper_commit()
so the comment is not valid anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1480946626-30917-1-git-send-email-gustavo@padovan.org
|
|
Pull sparc fix from David Miller:
"A use-before-NULL-check from Dan Carpenter"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
dbri: move dereference after check for NULL
|
|
A "real" driver for this hardware has now landed in the networking tree,
so remove this old staging driver so that we don't have multiple drivers
for the same hardware, and so people don't waste their time trying to
clean up this old code.
Cc: Lior Dotan <liodot@gmail.com>
Cc: Christopher Harrer <charrer@alacritech.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We accidentally introduced a dereference before the NULL check in
xmit_descs() as part of silencing a GCC warning.
Fixes: 16f46050e709 ("dbri: Fix compiler warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) When dcbnl_cee_fill() fails to be able to push a new netlink
attribute, it return 0 instead of an error code. From Pan Bian.
2) Two suffix handling fixes to FIB trie code, from Alexander Duyck.
3) bnxt_hwrm_stat_ctx_alloc() goes through all the trouble of setting
and maintaining a return code 'rc' but fails to actually return it.
Also from Pan Bian.
4) ping socket ICMP handler needs to validate ICMP header length, from
Kees Cook.
5) caif_sktinit_module() has this interesting logic:
int err = sock_register(...);
if (!err)
return err;
return 0;
Just return sock_register()'s return value directly which is the
only possible correct thing to do.
6) Two bnx2x driver fixes from Yuval Mintz, return a reasonable
estimate from get_ringparam() ethtool op when interface is down and
avoid trying to use UDP port based tunneling on 577xx chips.
7) Fix ep93xx_eth crash on module unload from Florian Fainelli.
8) Missing uapi exports, from Stephen Hemminger.
9) Don't schedule work from sk_destruct(), because the socket will be
freed upon return from that function. From Herbert Xu.
10) Buggy drivers, of which we know there is at least one, can send a
huge packet into the TCP stack but forget to set the gso_size in the
SKB, which causes all kinds of problems.
Correct this when it happens, and emit a one-time warning with the
device name included so that it can be diagnosed more easily.
From Marcelo Ricardo Leitner.
11) virtio-net does DMA off the stack causes hiccups with VMAP_STACK,
fix from Andy Lutomirski.
12) Fix fec driver compilation with CONFIG_M5272, from Nikita
Yushchenko.
13) mlx5 fixes from Kamal Heib, Saeed Mahameed, and Mohamad Haj Yahia.
(erroneously flushing queues on error, module parameter validation,
etc)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
net/mlx5e: Change the SQ/RQ operational state to positive logic
net/mlx5e: Don't flush SQ on error
net/mlx5e: Don't notify HW when filling the edge of ICO SQ
net/mlx5: Fix query ISSI flow
net/mlx5: Remove duplicate pci dev name print
net/mlx5: Verify module parameters
net: fec: fix compile with CONFIG_M5272
be2net: Add DEVSEC privilege to SET_HSW_CONFIG command.
virtio-net: Fix DMA-from-the-stack in virtnet_set_mac_address()
tcp: warn on bogus MSS and try to amend it
uapi glibc compat: fix outer guard of net device flags enum
net: stmmac: clear reset value of snps, wr_osr_lmt/snps, rd_osr_lmt before writing
netlink: Do not schedule work from sk_destruct
uapi: export nf_log.h
uapi: export tc_skbmod.h
net: ep93xx_eth: Do not crash unloading module
bnx2x: Prevent tunnel config for 577xx
bnx2x: Correct ringparam estimate when DOWN
isdn: hisax: set error code on failure
net: bnx2x: fix improper return value
...
|
|
The shmem hole punching with fallocate(FALLOC_FL_PUNCH_HOLE) does not
want to race with generating new pages by faulting them in.
However, the wait-queue used to delay the page faulting has a serious
problem: the wait queue head (in shmem_fallocate()) is allocated on the
stack, and the code expects that "wake_up_all()" will make sure that all
the queue entries are gone before the stack frame is de-allocated.
And that is not at all necessarily the case.
Yes, a normal wake-up sequence will remove the wait-queue entry that
caused the wakeup (see "autoremove_wake_function()"), but the key
wording there is "that caused the wakeup". When there are multiple
possible wakeup sources, the wait queue entry may well stay around.
And _particularly_ in a page fault path, we may be faulting in new pages
from user space while we also have other things going on, and there may
well be other pending wakeups.
So despite the "wake_up_all()", it's not at all guaranteed that all list
entries are removed from the wait queue head on the stack.
Fix this by introducing a new wakeup function that removes the list
entry unconditionally, even if the target process had already woken up
for other reasons. Use that "synchronous" function to set up the
waiters in shmem_fault().
This problem has never been seen in the wild afaik, but Dave Jones has
reported it on and off while running trinity. We thought we fixed the
stack corruption with the blk-mq rq_list locking fix (commit
7fe311302f7d: "blk-mq: update hardware and software queues for sleeping
alloc"), but it turns out there was _another_ stack corruptor hiding
in the trinity runs.
Vegard Nossum (also running trinity) was able to trigger this one fairly
consistently, and made us look once again at the shmem code due to the
faults often being in that area.
Reported-and-tested-by: Vegard Nossum <vegard.nossum@oracle.com>.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes 2016-12-04
Some bug fixes for mlx5 core and mlx5e driver.
v1->v2:
- replace "uint" with "unsigned int"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the negative logic (i.e. FLUSH state), after the RQ/SQ reopen
we will have a time interval that the RQ/SQ is not really ready and the
state indicates that its not in FLUSH state because the initial SQ/RQ struct
memory starts as zeros.
Now we changed the state to indicate if the SQ/RQ is opened and we will
set the READY state after finishing preparing all the SQ/RQ resources.
Fixes: 6e8dd6d6f4bd ("net/mlx5e: Don't wait for SQ completions on close")
Fixes: f2fde18c52a7 ("net/mlx5e: Don't wait for RQ completions on close")
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are doing SQ descriptors cleanup in driver.
Fixes: 6e8dd6d6f4bd ("net/mlx5e: Don't wait for SQ completions on close")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are going to do this a couple of steps ahead anyway.
Fixes: d3c9bc2743dc ("net/mlx5e: Added ICO SQs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In old FWs query ISSI command is not supported and for some of those FWs
it might fail with status other than "MLX5_CMD_STAT_BAD_OP_ERR".
In such case instead of failing the driver load, we will treat any FW
status other than 0 for Query ISSI FW command as ISSI not supported and
assume ISSI=0 (most basic driver/FW interface).
In case of driver syndrom (query ISSI failure by driver) we will fail
driver load.
Fixes: f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicate pci dev name printing from mlx5_core_warn/dbg.
Fixes: 5a7883989b1c ('net/mlx5_core: Improve mlx5 messages')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify the mlx5_core module parameters by making sure that they are in
the expected range and if they aren't restore them to their default
values.
Fixes: 9603b61de1ee ('mlx5: Move pci device handling from mlx5_ib to mlx5_core')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces the RX checksum function to check the
status of the hardware calculated checksum and its error and
appropriately convey status to the upper stack in skb->ip_summed
field.
In hardware, we only support checksum for the following
protocols:
1) IPv4,
2) TCP(over IPv4 or IPv6),
3) UDP(over IPv4 or IPv6),
4) SCTP(over IPv4 or IPv6)
but we support many L3(IPv4, IPv6, MPLS, PPPoE etc) and
L4(TCP, UDP, GRE, SCTP, IGMP, ICMP etc.) protocols.
Hardware limitation:
Our present hardware RX Descriptor lacks L3/L4 checksum
"Status & Error" bit (which usually can be used to indicate whether
checksum was calculated by the hardware and if there was any error
encountered during checksum calculation).
Software workaround:
We do get info within the RX descriptor about the kind of
L3/L4 protocol coming in the packet and the error status. These
errors might not just be checksum errors but could be related to
version, length of IPv4, UDP, TCP etc.
Because there is no-way of knowing if it is a L3/L4 error due
to bad checksum or any other L3/L4 error, we will not (cannot)
convey hardware checksum status(CHECKSUM_UNNECESSARY) for such
cases to upper stack and will not maintain the RX L3/L4 checksum
counters as well.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 80cca775cdc4 ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cdc4 ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
