| Age | Commit message (Collapse) | Author |
|---|
|
The probe routine acquires the reset GPIO using GPIOD_OUT_LOW. Directly
afterwards it calls acx565akm_detect(), which sets the GPIO value to
HIGH. If the bootloader initialized the GPIO to HIGH before the probe
routine was called, there is only a very short time period of a few
instructions where the reset signal is LOW. Exact time depends on
compiler optimizations, kernel configuration and alignment of the stars,
but I expect it to be always way less than 10us. There are no public
datasheets for the panel, but acx565akm_power_on() has a comment with
timings and reset period should be at least 10us. So this potentially
brings the panel into a half-reset state.
The result is, that panel may not work after boot and can get into a
working state by re-enabling it (e.g. by blanking + unblanking), since
that does a clean reset cycle. This bug has recently been hit by Ivaylo
Dimitrov, but there are some older reports which are probably the same
bug. At least Tony Lindgren, Peter Ujfalusi and Jarkko Nikula have
experienced it in 2017 describing the blank/unblank procedure as
possible workaround.
Note, that the bug really goes back in time. It has originally been
introduced in the predecessor of the omapfb driver in commit 3c45d05be382
("OMAPDSS: acx565akm panel: handle gpios in panel driver") in 2012.
That driver eventually got replaced by a newer one, which had the bug
from the beginning in commit 84192742d9c2 ("OMAPDSS: Add Sony ACX565AKM
panel driver") and still exists in fbdev world. That driver has later
been copied to omapdrm and then was used as a basis for this driver.
Last but not least the omapdrm specific driver has been removed in
commit 45f16c82db7e ("drm/omap: displays: Remove unused panel drivers").
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes: 1c8fc3f0c5d2 ("drm/panel: Add driver for the Sony ACX565AKM panel")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127200429.129868-1-sebastian.reichel@collabora.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Two more places which invoke tracing from RCU disabled regions in the
idle path.
Similar to the entry path the low level idle functions have to be
non-instrumentable"
* tag 'locking-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_idle: Fix intel_idle() vs tracing
sched/idle: Fix arch_cpu_idle() vs tracing
|
|
In case of panels with low vertical back porch, the prefill bw
requirement will be high as we will have less time(vbp+pw) to
fetch and fill the hw latency buffers before start of first line
in active period.
For ex:
Say hw_latency_line_buffers = 24, and if blanking vbp+pw = 10
Here we need to fetch 24 lines of data in 10 line times.
This will increase the bw to the ratio of linebuffers to blanking.
DPU hw can also fetch data during vertical front porch provided
interface prefetch is enabled. Use vfp in the prefill calculation
as dpu driver enables prefetch if the blanking is not sufficient
to fill the latency lines.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two fixes for irqchip drivers:
- Save and restore the GICV3 ITS state unconditionally on
suspend/resume to handle firmware which fails to do so.
- Use the correct index into the fwspec parameters to read the irq
trigger type in the EXIU chip driver"
* tag 'irq-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Unconditionally save/restore the ITS state on suspend
irqchip/exiu: Fix the index of fwspec for IRQ type
|
|
GPU targets with an MMU-500 attached have a slightly different process for
enabling system cache. Use the compatible string on the IOMMU phandle
to see if an MMU-500 is attached and modify the programming sequence
accordingly.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The last level system cache can be partitioned to 32 different
slices of which GPU has two slices preallocated. One slice is
used for caching GPU buffers and the other slice is used for
caching the GPU SMMU pagetables. This talks to the core system
cache driver to acquire the slice handles, configure the SCID's
to those slices and activates and deactivates the slices upon
GPU power collapse and restore.
Some support from the IOMMU driver is also needed to make use
of the system cache to set the right TCR attributes. GPU then
has the ability to override a few cacheability parameters which
it does to override write-allocate to write-no-allocate as the
GPU hardware does not benefit much from it.
DOMAIN_ATTR_IO_PGTABLE_CFG is another domain level attribute used
by the IOMMU driver for pagetable configuration which will be used
to set a quirk initially to set the right attributes to cache the
hardware pagetables into the system cache.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
[saiprakash.ranjan: fix to set attr before device attach to iommu and rebase]
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The register read-modify-write construct is generic enough
that it can be used by other subsystems as needed, create
a more generic rmw() function and have the gpu_rmw() use
this new function.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
into msm-next-staging
Pull in new iommu domain attr.
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
linux/rational.h is included more than once, Remove the one that isn't
necessary.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The only usage of dsi_host_ops is to assign its address to the ops field
in the mipi_dsi_host struct, which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
'struct tu_algo_data' is huge ~400 Bytes.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/dp/dp_ctrl.c: In function ‘_dp_ctrl_calc_tu.constprop’:
drivers/gpu/drm/msm/dp/dp_ctrl.c:938:1: warning: the frame size of 1184 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chandan Uddaraju <chandanu@codeaurora.org>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c:83:7: warning: no previous prototype for ‘state_kcalloc’ [-Wmissing-prototypes]
drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c:95:7: warning: no previous prototype for ‘state_kmemdup’ [-Wmissing-prototypes]
drivers/gpu/drm/msm/adreno/a6xx_gpu_state.c:947:6: warning: no previous prototype for ‘a6xx_gpu_state_destroy’ [-Wmissing-prototypes]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/msm_gem_shrinker.c:108: warning: Function parameter or member 'dev' not described in 'msm_gem_shrinker_init'
drivers/gpu/drm/msm/msm_gem_shrinker.c:108: warning: Excess function parameter 'dev_priv' description in 'msm_gem_shrinker_init'
drivers/gpu/drm/msm/msm_gem_shrinker.c:126: warning: Function parameter or member 'dev' not described in 'msm_gem_shrinker_cleanup'
drivers/gpu/drm/msm/msm_gem_shrinker.c:126: warning: Excess function parameter 'dev_priv' description in 'msm_gem_shrinker_cleanup'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/msm_drv.c:124:15: warning: no previous prototype for ‘_msm_ioremap’ [-Wmissing-prototypes]
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
descriptions
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:152: warning: Function parameter or member 'plane' not described in '_dpu_plane_calc_bw'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:152: warning: Function parameter or member 'fb' not described in '_dpu_plane_calc_bw'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:152: warning: Excess function parameter 'Plane' description in '_dpu_plane_calc_bw'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:200: warning: Function parameter or member 'plane' not described in '_dpu_plane_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:200: warning: Excess function parameter 'Plane' description in '_dpu_plane_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:232: warning: Function parameter or member 'src_width' not described in '_dpu_plane_calc_fill_level'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:232: warning: Excess function parameter 'src_wdith' description in '_dpu_plane_calc_fill_level'
drivers/gpu/drm/msm/disp/dpu1/dpu_plane.c:1060: warning: Function parameter or member 'error' not described in 'dpu_plane_set_error'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kalyan Thota <kalyan_t@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c:150: warning: Function parameter or member 'dpu_kms' not described in 'dpu_vbif_set_ot_limit'
drivers/gpu/drm/msm/disp/dpu1/dpu_vbif.c:150: warning: Excess function parameter 'vbif' description in 'dpu_vbif_set_ot_limit'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
description
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c:247: warning: Excess function parameter 'Return' description in '_dpu_rm_check_lm_peer'
drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c:283: warning: Function parameter or member 'global_state' not described in '_dpu_rm_check_lm_and_get_connected_blks'
drivers/gpu/drm/msm/disp/dpu1/dpu_rm.c:283: warning: Excess function parameter 'Return' description in '_dpu_rm_check_lm_and_get_connected_blks'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:240: warning: Function parameter or member 'ctx' not described in 'dpu_hw_sspp_setup_format'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:240: warning: Function parameter or member 'fmt' not described in 'dpu_hw_sspp_setup_format'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:240: warning: Function parameter or member 'flags' not described in 'dpu_hw_sspp_setup_format'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:240: warning: Function parameter or member 'rect_mode' not described in 'dpu_hw_sspp_setup_format'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:446: warning: Function parameter or member 'ctx' not described in 'dpu_hw_sspp_setup_rects'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:446: warning: Function parameter or member 'cfg' not described in 'dpu_hw_sspp_setup_rects'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_sspp.c:446: warning: Function parameter or member 'rect_index' not described in 'dpu_hw_sspp_setup_rects'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c:55: warning: Function parameter or member 'ctx' not described in '_stage_offset'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_lm.c:55: warning: Excess function parameter 'c' description in '_stage_offset'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:207: warning: Function parameter or member 'cur_slave' not described in 'dpu_encoder_virt'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:207: warning: Function parameter or member 'hw_pp' not described in 'dpu_encoder_virt'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:207: warning: Function parameter or member 'intfs_swapped' not described in 'dpu_encoder_virt'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1445: warning: Function parameter or member 'drm_enc' not described in '_dpu_encoder_trigger_flush'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1445: warning: Function parameter or member 'phys' not described in '_dpu_encoder_trigger_flush'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1445: warning: Function parameter or member 'extra_flush_bits' not described in '_dpu_encoder_trigger_flush'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1481: warning: Function parameter or member 'phys' not described in '_dpu_encoder_trigger_start'
drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c:1564: warning: Function parameter or member 'dpu_enc' not described in '_dpu_encoder_kickoff_phys'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
are used
These tables are not large or overbearing, so moving them into the
source file seems like the right thing to do. The alternative is to
use __maybe_unused, which is undesirable.
Fixes the following W=1 kernel build warning(s):
In file included from drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c:11:
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog_format.h:7:23: warning: ‘qcom_compressed_supported_formats’ defined but not used [-Wunused-const-variable=]
7 | static const uint32_t qcom_compressed_supported_formats[] = {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog_format.h:48:23: warning: ‘plane_formats_yuv’ defined but not used [-Wunused-const-variable=]
48 | static const uint32_t plane_formats_yuv[] = {
| ^~~~~~~~~~~~~~~~~
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog_format.h:17:23: warning: ‘plane_formats’ defined but not used [-Wunused-const-variable=]
17 | static const uint32_t plane_formats[] = {
| ^~~~~~~~~~~~~
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
'max_linewidth'
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c:124:19: warning: initialized field overwritten [-Woverride-init]
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c:124:19: note: (near initialization for ‘sm8250_dpu_caps.max_linewidth’)
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'fmt' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'a' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'r' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'g' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'b' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'e0' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'e1' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'e2' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'e3' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'uc' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'alpha' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'bp' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'flg' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'fm' not described in 'INTERLEAVED_RGB_FMT'
drivers/gpu/drm/msm/disp/dpu1/dpu_formats.c:50: warning: Function parameter or member 'np' not described in 'INTERLEAVED_RGB_FMT'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Fritz Koenig <frkoenig@google.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
description
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_blk.c:28: warning: Function parameter or member 'hw_blk' not described in 'dpu_hw_blk_init'
drivers/gpu/drm/msm/disp/dpu1/dpu_hw_blk.c:120: warning: Excess function parameter 'free_blk' description in 'dpu_hw_blk_put'
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:31: warning: Enum value 'DPU_PERF_MODE_MAX' not described in enum 'dpu_perf_mode'
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:34: warning: Cannot understand * @_dpu_core_perf_calc_bw() - to calculate BW per crtc
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:73: warning: Function parameter or member 'kms' not described in '_dpu_core_perf_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:73: warning: Function parameter or member 'crtc' not described in '_dpu_core_perf_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:73: warning: Function parameter or member 'state' not described in '_dpu_core_perf_calc_clk'
drivers/gpu/drm/msm/disp/dpu1/dpu_core_perf.c:249: warning: Cannot understand * @dpu_core_perf_crtc_release_bw() - request zero bandwidth
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kalyan Thota <kalyan_t@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:227: warning: Function parameter or member 'ctl' not described in 'mdp5_ctl_set_encoder_state'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:227: warning: Function parameter or member 'pipeline' not described in 'mdp5_ctl_set_encoder_state'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:227: warning: Function parameter or member 'enabled' not described in 'mdp5_ctl_set_encoder_state'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:227: warning: Excess function parameter 'enable' description in 'mdp5_ctl_set_encoder_state'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:529: warning: Function parameter or member 'ctl' not described in 'mdp5_ctl_commit'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:529: warning: Function parameter or member 'pipeline' not described in 'mdp5_ctl_commit'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:529: warning: Function parameter or member 'flush_mask' not described in 'mdp5_ctl_commit'
drivers/gpu/drm/msm/disp/mdp5/mdp5_ctl.c:529: warning: Function parameter or member 'start' not described in 'mdp5_ctl_commit'
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Borislav Petkov:
"More EFI fixes forwarded from Ard Biesheuvel:
- revert efivarfs kmemleak fix again - it was a false positive
- make CONFIG_EFI_EARLYCON depend on CONFIG_EFI explicitly so it does
not pull in other dependencies unnecessarily if CONFIG_EFI is not
set
- defer attempts to load SSDT overrides from EFI vars until after the
efivar layer is up"
* tag 'efi-urgent-for-v5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: EFI_EARLYCON should depend on EFI
efivarfs: revert "fix memory leak in efivarfs_create()"
efi/efivars: Set generic ops before loading SSDT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"A couple of urgent fixes which accumulated this last week:
- Two resctrl fixes to prevent refcount leaks when manipulating the
resctrl fs (Xiaochen Shen)
- Correct prctl(PR_GET_SPECULATION_CTRL) reporting (Anand K Mistry)
- A fix to not lose already seen MCE severity which determines
whether the machine can recover (Gabriele Paoloni)"
* tag 'x86_urgent_for_v5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Do not overwrite no_way_out if mce_end() fails
x86/speculation: Fix prctl() when spectre_v2_user={seccomp,prctl},ibpb
x86/resctrl: Add necessary kernfs_put() calls to prevent refcount leak
x86/resctrl: Remove superfluous kernfs_get() calls to prevent refcount leak
|
|
In the Rockchip DRM LVDS component driver, the endpoint id provided to
drm_of_find_panel_or_bridge is grabbed from the endpoint's reg property.
However, the property may be missing in the case of a single endpoint.
Initialize the endpoint_id variable to 0 to avoid using an
uninitialized variable in that case.
Fixes: 34cc0aa25456 ("drm/rockchip: Add support for Rockchip Soc LVDS")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110200430.1713467-1-paul.kocialkowski@bootlin.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"I've collected a handful of fixes over the past few weeks:
- A fix to un-break the build-id argument to the vDSO build, which is
necessary for the LLVM linker.
- A fix to initialize the jump label subsystem, without which it (and
all the stuff that uses it) doesn't actually function.
- A fix to include <asm/barrier.h> from <vdso/processor.h>, without
which some drivers won't compile"
* tag 'riscv-for-linus-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: fix barrier() use in <vdso/processor.h>
RISC-V: Add missing jump label initialization
riscv: Explicitly specify the build id style in vDSO Makefile again
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Fixes: a1a8b4594f8d ("NFC: pn544: i2c: Add DTS Documentation")
Fixes: 6be88670fc59 ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Fixes: e3b329221567 ("dt-bindings: can: tcan4x5x: Update binding to use interrupt property")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for tcan4x5x.txt
Link: https://lore.kernel.org/r/20201026153620.89268-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Dany Madden says:
====================
ibmvnic: assorted bug fixes
Assorted fixes for ibmvnic originated from "[PATCH net 00/15] ibmvnic:
assorted bug fixes" sent by Lijun Pan.
====================
Link: https://lore.kernel.org/r/20201126000432.29897-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reduce the wait time for Command Response Queue response from 30 seconds
to 20 seconds, as recommended by VIOS and Power Hypervisor teams.
Fixes: bd0b672313941 ("ibmvnic: Move login and queue negotiation into ibmvnic_open")
Fixes: 53da09e92910f ("ibmvnic: Add set_link_state routine for setting adapter link state")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reset timeout is going off right after adapter reset. This patch ensures
that timeout is scheduled if it has been 5 seconds since the last reset.
5 seconds is the default watchdog timeout.
Fixes: ed651a10875f1 ("ibmvnic: Updated reset handling")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
send_login() does not check for the result of ibmvnic_send_crq() of the
login request. This results in the driver needlessly retrying the login
10 times even when CRQ is no longer active. Check the return code and
give up in case of errors in sending the CRQ.
The only time we want to retry is if we get a PARITALSUCCESS response
from the partner.
Fixes: 032c5e82847a2 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If after ibmvnic sends a LOGIN it gets a FAILOVER, it is possible that
the worker thread will start reset process and free the login response
buffer before it gets a (now stale) LOGIN_RSP. The ibmvnic tasklet will
then try to access the login response buffer and crash.
Have ibmvnic track pending logins and discard any stale login responses.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If auto-priority failover is enabled, the backing device needs time
to settle if hard resetting fails for any reason. Add a delay of 60
seconds before retrying the hard-reset.
Fixes: 2770a7984db5 ("ibmvnic: Introduce hard reset recovery")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a failed reset, driver could end up in VNIC_PROBED or VNIC_CLOSED
state and cannot recover in subsequent resets, leaving it offline.
This patch restores the adapter state to reset_state, the original
state when reset was called.
Fixes: b27507bb59ed5 ("net/ibmvnic: unlock rtnl_lock in reset so linkwatch_event can run")
Fixes: 2770a7984db58 ("ibmvnic: Introduce hard reset recovery")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
scrq->msgs could be NULL during device reset, causing Linux to crash.
So, check before memset scrq->msgs.
Fixes: c8b2ad0a4a901 ("ibmvnic: Sanitize entire SCRQ buffer on reset")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When ibmvnic fails to reset, it breaks out of the reset loop and frees
all of the remaining resets from the workqueue. Doing so prevents the
adapter from recovering if no reset is scheduled after that. Instead,
have the driver continue to process resets on the workqueue.
Remove the no longer need free_all_rwi().
Fixes: ed651a10875f1 ("ibmvnic: Updated reset handling")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Inconsistent login with the vnicserver is causing the device to be
removed. This does not give the device a chance to recover from error
state. This patch schedules a FATAL reset instead to bring the adapter
up.
Fixes: 032c5e82847a2 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Fix insufficient validation of IPSET_ATTR_IPADDR_IPV6 reported
by syzbot.
2) Remove spurious reports on nf_tables when lockdep gets disabled,
from Florian Westphal.
3) Fix memleak in the error path of error path of
ip_vs_control_net_init(), from Wang Hai.
4) Fix missing control data in flow dissector, otherwise IP address
matching in hardware offload infra does not work.
5) Fix hardware offload match on prefix IP address when userspace
does not send a bitwise expression to represent the prefix.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nftables_offload: build mask based from the matching bytes
netfilter: nftables_offload: set address type in control dissector
ipvs: fix possible memory leak in ip_vs_control_net_init
netfilter: nf_tables: avoid false-postive lockdep splat
netfilter: ipset: prevent uninit-value in hash_ip6_add
====================
Link: https://lore.kernel.org/r/20201127190313.24947-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
a proper kernel configuration for running kselftest can be obtained with:
$ yes | make kselftest-merge
enable compile support for the 'red' qdisc: otherwise, tdc kselftest fail
when trying to run tdc test items contained in red.json.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/cfa23f2d4f672401e6cebca3a321dd1901a9ff07.1606416464.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When inet_rtm_getroute() was converted to use the RCU variants of
ip_route_input() and ip_route_output_key(), the TOS parameters
stopped being masked with IPTOS_RT_MASK before doing the route lookup.
As a result, "ip route get" can return a different route than what
would be used when sending real packets.
For example:
$ ip route add 192.0.2.11/32 dev eth0
$ ip route add unreachable 192.0.2.11/32 tos 2
$ ip route get 192.0.2.11 tos 2
RTNETLINK answers: No route to host
But, packets with TOS 2 (ECT(0) if interpreted as an ECN bit) would
actually be routed using the first route:
$ ping -c 1 -Q 2 192.0.2.11
PING 192.0.2.11 (192.0.2.11) 56(84) bytes of data.
64 bytes from 192.0.2.11: icmp_seq=1 ttl=64 time=0.173 ms
--- 192.0.2.11 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.173/0.173/0.173/0.000 ms
This patch re-applies IPTOS_RT_MASK in inet_rtm_getroute(), to
return results consistent with real route lookups.
Fixes: 3765d35ed8b9 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/b2d237d08317ca55926add9654a48409ac1b8f5b.1606412894.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-11-28
1) Do not reference the skb for xsk's generic TX side since when looped
back into RX it might crash in generic XDP, from Björn Töpel.
2) Fix umem cleanup on a partially set up xsk socket when being destroyed,
from Magnus Karlsson.
3) Fix an incorrect netdev reference count when failing xsk_bind() operation,
from Marek Majtyka.
4) Fix bpftool to set an error code on failed calloc() in build_btf_type_table(),
from Zhen Lei.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add MAINTAINERS entry for BPF LSM
bpftool: Fix error return value in build_btf_type_table
net, xsk: Avoid taking multiple skbuff references
xsk: Fix incorrect netdev reference count
xsk: Fix umem cleanup bug at socket destruct
MAINTAINERS: Update XDP and AF_XDP entries
====================
Link: https://lore.kernel.org/r/20201128005104.1205-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Fix head/tailroom issues for fragments, by Sven Eckelmann (3 patches)
* tag 'batadv-net-pullrequest-20201127' of git://git.open-mesh.org/linux-merge:
batman-adv: Don't always reallocate the fragmentation skb head
batman-adv: Reserve needed_*room for fragments
batman-adv: Consider fragmentation for needed_headroom
====================
Link: https://lore.kernel.org/r/20201127173849.19208-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Netfilter changes PACKET_OTHERHOST to PACKET_HOST before invoking the
hooks as, while it's an expected value for a bridge, routing expects
PACKET_HOST. The change is undone later on after hook traversal. This
can be seen with pairs of functions updating skb>pkt_type and then
reverting it to its original value:
For hook NF_INET_PRE_ROUTING:
setup_pre_routing / br_nf_pre_routing_finish
For hook NF_INET_FORWARD:
br_nf_forward_ip / br_nf_forward_finish
But the third case where netfilter does this, for hook
NF_INET_POST_ROUTING, the packet type is changed in br_nf_post_routing
but never reverted. A comment says:
/* We assume any code from br_dev_queue_push_xmit onwards doesn't care
* about the value of skb->pkt_type. */
But when having a tunnel (say vxlan) attached to a bridge we have the
following call trace:
br_nf_pre_routing
br_nf_pre_routing_ipv6
br_nf_pre_routing_finish
br_nf_forward_ip
br_nf_forward_finish
br_nf_post_routing <- pkt_type is updated to PACKET_HOST
br_nf_dev_queue_xmit <- but not reverted to its original value
vxlan_xmit
vxlan_xmit_one
skb_tunnel_check_pmtu <- a check on pkt_type is performed
In this specific case, this creates issues such as when an ICMPv6 PTB
should be sent back. When CONFIG_BRIDGE_NETFILTER is enabled, the PTB
isn't sent (as skb_tunnel_check_pmtu checks if pkt_type is PACKET_HOST
and returns early).
If the comment is right and no one cares about the value of
skb->pkt_type after br_dev_queue_push_xmit (which isn't true), resetting
it to its original value should be safe.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20201123174902.622102-1-atenart@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Remove unused OBJSIZE variable.
- Fix rootless deb-pkg build in a setgid directory.
* tag 'kbuild-fixes-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
builddeb: Fix rootless build in setuid/setgid directory
kbuild: remove unused OBJSIZE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tool fixes from Arnaldo Carvalho de Melo:
- Fix die_entrypc() when DW_AT_ranges DWARF attribute not available
- Cope with broken DWARF (missing DW_AT_declaration) generated by some
recent gcc versions
- Do not generate CGROUP metadata events when not asked to in 'perf
record'
- Use proper CPU for shadow stats in 'perf stat'
- Update copy of libbpf's hashmap.c, silencing tools/perf build warning
- Fix return value in 'perf diff'
* tag 'perf-tools-fixes-for-v5.10-2020-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf probe: Change function definition check due to broken DWARF
perf probe: Fix to die_entrypc() returns error correctly
perf stat: Use proper cpu for shadow stats
perf record: Synthesize cgroup events only if needed
perf diff: Fix error return value in __cmd_diff()
perf tools: Update copy of libbpf's hashmap.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY driver fixes from Greg KH:
"Here are a few small USB and PHY driver fixes for 5.10-rc6. They
include:
- small PHY driver fixes to resolve reported issues
- USB quirks added for "broken" devices
- typec fixes for reported problems
- USB gadget fixes for small issues
Full details are in the shortlog, nothing major in here and all have
been in linux-next with no reported issues"
* tag 'usb-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: stusb160x: fix power-opmode property with typec-power-opmode
USB: core: Change %pK for __user pointers to %px
USB: core: Fix regression in Hercules audio card
usb: gadget: Fix memleak in gadgetfs_fill_super
usb: gadget: f_midi: Fix memleak in f_midi_alloc
USB: quirks: Add USB_QUIRK_DISCONNECT_SUSPEND quirk for Lenovo A630Z TIO built-in usb-audio card
usb: typec: qcom-pmic-typec: fix builtin build errors
phy: mediatek: fix spelling mistake in Kconfig "veriosn" -> "version"
phy: qualcomm: Fix 28 nm Hi-Speed USB PHY OF dependency
phy: qualcomm: usb: Fix SuperSpeed PHY OF dependency
phy: intel: PHY_INTEL_KEEMBAY_EMMC should depend on ARCH_KEEMBAY
usb: cdns3: gadget: calculate TD_SIZE based on TD
usb: cdns3: gadget: initialize link_trb as NULL
phy: cpcap-usb: Use IRQF_ONESHOT
phy: qcom-qmp: Initialize another pointer to NULL
phy: tegra: xusb: Fix dangling pointer on probe failure
phy: usb: Fix incorrect clearing of tca_drv_sel bit in SETUP reg for 7211
|
