| Age | Commit message (Collapse) | Author |
|---|
|
Since Bluetooth 4.1 there are two additional values for SSP OOB data,
namely C-256 and R-256. This patch updates the EIR definitions to take
into account both the 192 and 256 bit variants of C and R.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Simple patch to make symbols static. Symbols that are not
shared with other parts of the kernel can be made static.
This change also removes several sparse complains.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ajit Pal Singh <ajitpal.singh@st.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Some temperature sensors only get updated every few seconds and while
waiting for the first irq reporting a (new) temperature to happen there
get_temp operand will return -EAGAIN as it does not have any data to report
yet.
Not logging an error in this case avoids messages like these from showing
up in dmesg on affected systems:
[ 1.219353] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.015433] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.416737] thermal thermal_zone0: failed to read out thermal zone 0
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
r8a73a4 is R-Mobile APE6, not AP6.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Prevent UDP tunnels from operating on garbage socket
So this should do the rest of the work such that when we encapsulate
into a UDP tunnel, the output path works on the UDP tunnel's socket
rather than skb->sk.
Part of this work is based upon changes done by Jiri Pirko some time
ago.
Basically the first step is to pass the socket through the nf_hook
okfn(), and then next we do the same for the UDP tunnel xmit routines.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
|
|
The Makefile automatically generates the tomoyo policy files, which are
not removed by make clean (because they could have been provided by the
user). Instead of generating the missing files, use /dev/null if a
given file is not provided. Store the default exception_policy in
exception_policy.conf.default.
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Combine the generation of builtin-policy.h into a single command and use
if_changed, so that the file is regenerated each time the command
changes. The next patch will make use of this.
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Simplify the Makefile by using a readily available tool instead of a
custom sed script. The downside is that builtin-policy.h becomes
unreadable for humans, but it is only a generated file.
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is currently always set to NULL, but nf_queue is adjusted to be
prepared for it being set to a real socket by taking and releasing a
reference to that socket when necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This way we can consolidate where we setup new nf_hook_state objects,
to make sure the entire thing is initialized.
The only other place an nf_hook_object is instantiated is nf_queue,
wherein a structure copy is used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a driver doesn't implement the master->handle_err() callback and an
SPI transfer fails, the kernel will crash with a NULL pointer
dereference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0003000
[00000000] *pgd=80000040004003, *pmd=00000000
Internal error: Oops: 80000206 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.0.0-rc7-koelsch-05861-g1fc9fdd4add4f783 #1046
Hardware name: Generic R8A7791 (Flattened Device Tree)
task: eec359c0 ti: eec54000 task.ti: eec54000
PC is at 0x0
LR is at spi_transfer_one_message+0x1cc/0x1f0
Make the master->handle_err() callback optional to avoid the crash.
Also fix a spelling mistake in the callback documentation while we're at
it.
Fixes: b716c4ffc6a2b0bf ("spi: introduce master->handle_err() callback")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
While this driver was already using a 50ms resume
timeout, let's make sure everybody uses the same
macro so it's easy to fix later should anything
go wrong.
It also gives a more "stable" expectation to Linux
users.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Based on original work by Bin Liu <Bin Liu <b-liu@ti.com>>
Cc: Bin Liu <b-liu@ti.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Every USB Host controller should use this new
macro to define for how long resume signalling
should be driven on the bus.
Currently, almost every single USB controller
is using a 20ms timeout for resume signalling.
That's problematic for two reasons:
a) sometimes that 20ms timer expires a little
before 20ms, which makes us fail certification
b) some (many) devices actually need more than
20ms resume signalling.
Sure, in case of (b) we can state that the device
is against the USB spec, but the fact is that
we have no control over which device the certification
lab will use. We also have no control over which host
they will use. Most likely they'll be using a Windows
PC which, again, we have no control over how that
USB stack is written and how long resume signalling
they are using.
At the end of the day, we must make sure Linux passes
electrical compliance when working as Host or as Device
and currently we don't pass compliance as host because
we're driving resume signallig for exactly 20ms and
that confuses certification test setup resulting in
Certification failure.
Cc: <stable@vger.kernel.org> # v3.10+
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ar9550 or later chips, the AR_GPIO_IN_OUT register only can
control GPIO[0:3]. For the extra GPIO, use standard GPIO calls
instead of WMAC internal registers.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We can save some power by putting devices that are bound to vfio-pci
but not in use by the user in the D3hot power state. Devices get
woken into D0 when opened by the user. Resets return the device to
D0, so we need to re-apply the low power state after a bus reset.
It's tempting to try to use D3cold, but we have no reason to inhibit
hotplug of idle devices and we might get into a loop of having the
device disappear before we have a chance to try to use it.
A new module parameter allows this feature to be disabled if there are
devices that misbehave as a result of this change.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
As indicated in the comment, this is not entirely uncommon and
causes user concern for no reason.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
This copies the same support from pci-stub for exactly the same
purpose, enabling a set of PCI IDs to be automatically added to the
driver's dynamic ID table at module load time. The code here is
pretty simple and both vfio-pci and pci-stub are fairly unique in
being meta drivers, capable of attaching to any device, so there's no
attempt made to generalize the code into pci-core.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
If VFIO VGA access is disabled for the user, either by CONFIG option
or module parameter, we can often opt-out of VGA arbitration. We can
do this when PCI bridge control of VGA routing is possible. This
means that we must have a parent bridge and there must only be a
single VGA device below that bridge. Fortunately this is the typical
case for discrete GPUs.
Doing this allows us to minimize the impact of additional GPUs, in
terms of VGA arbitration, when they are only used via vfio-pci for
non-VGA applications.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Add a module option so that we don't require a CONFIG change and
kernel rebuild to disable VGA support. Not only can VGA support be
troublesome in itself, but by disabling it we can reduce the impact
to host devices by doing a VGA arbitration opt-out.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
vga_set_legacy_decoding() is defined in drivers/gpu/vga/vgaarb.c,
which is only compiled with CONFIG_VGA_ARB. A caller would
therefore get an undefined symbol if the VGA arbiter is not
enabled.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
|
|
This patch fix a spelling typo in MODULE_DESCRIPTION in
wl1251/main.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Use bool constants as the return values instead of 1 and 0.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
packet.
rtl8192cu can't connect to AP after physical reconnect.
according to dmesg, that problem's cause was DHCP timeout.
rtl_is_special_data function checks packet type for adjusting rate.
when that function is called from _rtl_rc_get_highest_rix, it can not
calculate offset correctly. so i add argument is_encn in rtl_is_special_data.
is_enc variable mean that iv header is added in skb parameter.
i test only rtl8192cu chipset. because i doesn't have other rtlwifi chipsets.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As the driver may send multiple wmi commands with identical cmd id,
it is more robust to check seq number for timeout instead.
Signed-off-by: Fred Chou <fred.chou.nd@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* some more work on LAR
* fixes for UMAC scan
* more work on debugging framework
* more work for 8000 devices
* cleanups and small bugfixes
|
|
The Bluetooth address setting for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Since the Intel Bluetooth support has its own header, it makes sense
to move all command structs into it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The Bluetooth address handling for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The majority of Intel Bluetooth vendor commands are shared between USB
and UART transports. This creates a separate module that eventually
will hold all Intel specific commands, but for now just start with the
commands to change the Bluetooth public address and check for the
default address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Future H:4 based UART drivers require custom packet types and custom
receive functions. To support this, extended the h4_recv_buf function
with a packet definition table.
For the default H:4 packets types of ACL data, SCO data and events,
provide helpers to reduce the amount of code duplication.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The Broadcom UART based devices seem to use a little bit different
firmare naming prefix. So add a separate table for these devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This adds the protocol support for Broadcom based UART devices to
enable firmware and patchram download procedure. It is a pretty
straight forward H:4 driver with the exception of actually having
its own setup and address configuration callbacks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
