| Age | Commit message (Collapse) | Author |
|---|
|
It is important to clear the hw->state value for non-stopped events
when they are added into the PMU. Otherwise when the event is
scheduled out, we won't read the counter because HES_UPTODATE is still
set. This breaks 'perf stat' and similar use cases, causing all the
events to show zero.
This worked for multi-pcr because we make explicit sparc_pmu_start()
calls in calculate_multiple_pcrs(). calculate_single_pcr() doesn't do
this because the idea there is to accumulate all of the counter
settings into the single pcr value. So we have to add explicit
hw->state handling there.
Like x86, we use the PERF_HES_ARCH bit to track truly stopped events
so that we don't accidently start them on a reload.
Related to all of this, sparc_pmu_start() is missing a userpage update
so add it.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.
This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.
For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb079cc3 ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use PIO mode instead if size is smaller than fifo size, since
dma may be less efficient.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Correct wml as the last rx sg length instead of the whole transfer
length. Otherwise, mtd_stresstest will be failed as below:
insmod mtd_stresstest.ko dev=0
=================================================
mtd_stresstest: MTD device: 0
mtd_stresstest: not NAND flash, assume page size is 512 bytes.
mtd_stresstest: MTD device size 4194304, eraseblock size 65536, page size 512, count of eraseblocks 64, pa0
mtd_stresstest: doing operations
mtd_stresstest: 0 operations done
mtd_test: mtd_read from 1ff532, size 880
mtd_test: mtd_read from 20c267, size 64998
spi_master spi0: I/O Error in DMA RX
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
mtd_test: error: read failed at 0x20c267
mtd_stresstest: error -110 occurred
=================================================
insmod: ERROR: could not insert module mtd_stresstest.ko: Connection timed out
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current dynamic burst length is based on the whole transfer length,
that's ok if there is only one sg, but is not right in case multi sgs
in one transfer,because the tail data should be based on the last sg
length instead of the whole transfer length. Move wml setting for DMA
to the later place, thus, the next patch could get the right last sg
length for wml setting. This patch is a preparation one, no any
function change involved.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
The Lochnagar board provides power supplies for the attached
CODEC/Amp device. Currently this driver supports the microphone
supplies and the digital core voltage for the attached
device. There are some additional supplies that will be
added in time but these supplies are sufficient for most
systems/use-cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This spares drivers from #ifdef-ing on CONFIG_PCI if the driver can be
optionally built on machines without PCI bus.
Consistent with acpi_driver_match_device() and similar.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SPI configuration state includes an SPI_NO_CS flag that disables
all CS line manipulation, for applications that want to manage their
own chip selects. However, this flag is ignored by the GPIO CS code
in the SPI framework.
Correct this omission with a trivial patch.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd writes:
"ARM: SoC fixes for 4.19
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this."
* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
ARM: dts: imx53-qsb: disable 1.2GHz OPP
|
|
Fix a leak of afs_server structs. The routine that installs them in the
various lookup lists and trees gets a ref on leaving the function, whether
it added the server or a server already exists. It shouldn't increment
the refcount if it added the server.
The effect of this that "rmmod kafs" will hang waiting for the leaked
server to become unused.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Just drop the "linux" part of the path, it was never correct.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 256ac0375098 ("dt-bindings: document devicetree bindings for mux-controllers and gpio-mux")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The file is GPL v2 or later.
Acked-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It turns out that the fix in commit 6636c3cc56 is bad; the assertion
that the iomap code no longer creates buffer heads is incorrect for
filesystems that set the IOMAP_F_BUFFER_HEAD flag.
Instead, what's happening is that gfs2_iomap_begin_write treats all
files that have the jdata flag set as journaled files, which is
incorrect as long as those files are inline ("stuffed"). We're handling
stuffed files directly via the page cache, which is why we ended up with
pages without buffer heads in gfs2_page_add_databufs.
Fix this by handling stuffed journaled files correctly in
gfs2_iomap_begin_write.
This reverts commit 6636c3cc5690c11631e6366cf9a28fb99c8b25bb.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
It doesn't make sense for a perf event to be configured as a CHAIN event
in isolation, so extend the arm_pmu structure with a ->filter_match()
function to allow the backend PMU implementation to reject CHAIN events
early.
Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We describe ranges of 'reserved' memory to userspace via /proc/iomem.
Commit 50d7ba36b916 ("arm64: export memblock_reserve()d regions via
/proc/iomem") updated the logic to export regions that were reserved
because their contents should be preserved. This allowed kexec-tools
to tell the difference between 'reserved' memory that must be
preserved and not overwritten, (e.g. the ACPI tables), and 'nomap'
memory that must not be touched without knowing the memory-attributes
(e.g. RAS CPER regions).
The above commit wrongly assumed that memblock_reserve() would not
be used to reserve regions that aren't memory. It turns out this is
exactly what early_init_dt_reserve_memory_arch() will do if it finds
a DT reserved-memory that was also carved out of the memory node, which
results in a WARN_ON_ONCE() and the region being reserved instead of
ignored. The ramoops description on hikey and dragonboard-410c both do
this, so we can't simply write this configuration off as "buggy firmware".
Avoid this issue by rewriting reserve_memblock_reserved_regions() so
that only the portions of reserved regions which overlap with mapped
memory are actually reserved.
Fixes: 50d7ba36b916 ("arm64: export memblock_reserve()d regions via /proc/iomem")
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Paolo Pisati <p.pisati@gmail.com>
CC: Akashi Takahiro <takahiro.akashi@linaro.org>
CC: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Access to the list of cells by /proc/net/afs/cells has a couple of
problems:
(1) It should be checking against SEQ_START_TOKEN for the keying the
header line.
(2) It's only holding the RCU read lock, so it can't just walk over the
list without following the proper RCU methods.
Fix these by using an hlist instead of an ordinary list and using the
appropriate accessor functions to follow it with RCU.
Since the code that adds a cell to the list must also necessarily change,
sort the list on insertion whilst we're at it.
Fixes: 989782dcdc91 ("afs: Overhaul cell database management")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Ulf writes:
"MMC core:
- Avoid fragile multiblock reads for the last sector in SPI mode
WIFI/SDIO:
- libertas: Fixup suspend sequence for the SDIO card"
* tag 'mmc-v4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
libertas: call into generic suspend code before turning off power
mmc: block: avoid multiblock reads for the last sector in SPI mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Linus writes:
"GPIO fix for the v4.19 series:
- Fix up the interrupt parent for the irqdomains."
* tag 'gpio-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Assign gpio_irq_chip::parents to non-stack pointer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Linus writes:
"pin control fix for v4.19:
A single pin control fix for v4.19:
- Interrupt setup in the MCP23S08 driver."
* tag 'pinctrl-v4.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mcp23s08: fix irq and irqchip setup order
|
|
Boris writes:
"mdt: fix for 4.19-rc8
* Fix a stack overflow in lib/bch.c"
* tag 'mtd/fixes-for-4.19-rc8' of git://git.infradead.org/linux-mtd:
lib/bch: fix possible stack overrun
|
|
Dave writes:
"drm fixes for 4.19-rc8
single nouveau runtime reference and mst change"
* tag 'drm-fixes-2018-10-12-1' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/drm/nouveau: Grab runtime PM ref in nv50_mstc_detect()
|
|
Doug writes:
"RDMA fixes:
Final for-rc pull request for 4.19
We only have one bug to submit this time around. It fixes a DMA
unmap issue where we unmapped the DMA address from the IOMMU before
we did from the card, resulting in a DMAR error with IOMMU enabled,
or possible crash without."
* tag 'for-gkh' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Unmap DMA addr from HCA before IOMMU
|
|
There is no need to have the 'struct dentry *dev_state' variable static
since new value always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Link: http://lkml.kernel.org/r/1539340822-117563-1-git-send-email-yuehaibing@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Dmitry writes:
"Input updates for v4.19-rc7
- we added a few scheduling points into various input interfaces to
ensure that large writes will not cause RCU stalls
- fixed configuring PS/2 keyboards as wakeup devices on newer
platforms
- added a new Xbox gamepad ID."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - add a schedule point in uinput_inject_events()
Input: evdev - add a schedule point in evdev_write()
Input: mousedev - add a schedule point in mousedev_write()
Input: i8042 - enable keyboard wakeups by default when s2idle is used
Input: xpad - add support for Xbox1 PDP Camo series gamepad
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes
Stephen writes:
"A couple of warning fixes:
Two fixes from Peter Oberparleiter <oberpar@linux.ibm.com>:
Commit 6b7dca401cb1 ("tracing: Allow gcov profiling on only ftrace subsystem")
uncovered linker problems when using gcov kernel profiling on some
architectures. These problems were likely introduced earlier, and are
possibly related to compiler changes."
* tag 'next-fixes-20181012' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
vmlinux.lds.h: Fix linker warnings about orphan .LPBX sections
vmlinux.lds.h: Fix incomplete .text.exit discards
|
|
If the size of spi-nor flash is larger than 16MB, the read_opcode
is set to SPINOR_OP_READ_1_1_4_4B, and fsl_qspi_get_seqid() will
return -EINVAL when cmd is SPINOR_OP_READ_1_1_4_4B. This can
cause read operation fail.
Fixes: e46ecda764dc ("mtd: spi-nor: Add Freescale QuadSPI driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Intel Ice Lake exposes the SPI serial flash controller as a PCI device
in the same way than Intel Denverton. Add Ice Lake SPI serial flash PCI
ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Fix up a compiler error on 64bit architectures where pointers
and integers differ in size.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is a potential execution path in which variable *ret* is checked
in an IF statement, and then its value is used to report an error at
line 659 without being properly initialized previously:
659 if (ret)
660 dev_err(priv->dev, "Failed to write to 0x%x (%d)\n", reg, ret);
Fix this by initializing variable *ret* to 0 in order to
avoid unpredictable or unintended results.
Addresses-Coverity-ID: 1471969 ("Uninitialized scalar variable")
Fixes: 218d72a77b0b ("pinctrl: madera: Add driver for Cirrus Logic Madera codecs")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After some recent menu governor changes, the promotion of the
"polling" state to a physical one is mostly controlled by the
latency limit (resulting from the "interactivity" factor) and
not by the time to the closest timer event, so it should be
sufficient to check the exit latency of that state for this
purpose (of course, its target residency still needs to be
within the next timer event range for energy-efficiency).
Also, the physical state the "polling" one is promoted to need not
be the next one in principle (in case the next state is disabled,
for example).
For these reasons, simplify the checks made to decide whether or
not to promote the "polling" state to a physical one and update
the target idle duration when it is promoted in case the residency
of the new state turns out to be above the tick boundary (in which
case there is no reason to stop the tick).
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c29 ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
gpio_hog depends on gdev field being initialized. This patch fixes an
OOPs during initialization of TI's AM335x-ICEv2.
Fixes: 3edfb7bd76bd1cba ("gpiolib: Show correct direction from the beginning")
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The previous patch introduced very large kernel stack usage and a Makefile
change to hide the warning about it.
From what I can tell, a number of things went wrong here:
- The BCH_MAX_T constant was set to the maximum value for 'n',
not the maximum for 't', which is much smaller.
- The stack usage is actually larger than the entire kernel stack
on some architectures that can use 4KB stacks (m68k, sh, c6x), which
leads to an immediate overrun.
- The justification in the patch description claimed that nothing
changed, however that is not the case even without the two points above:
the configuration is machine specific, and most boards never use the
maximum BCH_ECC_WORDS() length but instead have something much smaller.
That maximum would only apply to machines that use both the maximum
block size and the maximum ECC strength.
The largest value for 't' that I could find is '32', which in turn leads
to a 60 byte array instead of 2048 bytes. Making it '64' for future
extension seems also worthwhile, with 120 bytes for the array. Anything
larger won't fit into the OOB area on NAND flash.
With that changed, the warning can be enabled again.
Only linux-4.19+ contains the breakage, so this is only needed
as a stable backport if it does not make it into the release.
Fixes: 02361bc77888 ("lib/bch: Remove VLA usage")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
David writes:
"Networking
1) RXRPC receive path fixes from David Howells.
2) Re-export __skb_recv_udp(), from Jiri Kosina.
3) Fix refcounting in u32 classificer, from Al Viro.
4) Userspace netlink ABI fixes from Eugene Syromiatnikov.
5) Don't double iounmap on rmmod in ena driver, from Arthur
Kiyanovski.
6) Fix devlink string attribute handling, we must pull a copy into a
kernel buffer if the lifetime extends past the netlink request.
From Moshe Shemesh.
7) Fix hangs in RDS, from Ka-Cheong Poon.
8) Fix recursive locking lockdep warnings in tipc, from Ying Xue.
9) Clear RX irq correctly in socionext, from Ilias Apalodimas.
10) bcm_sf2 fixes from Florian Fainelli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: dsa: bcm_sf2: Call setup during switch resume
net: dsa: bcm_sf2: Fix unbind ordering
net: phy: sfp: remove sfp_mutex's definition
r8169: set RX_MULTI_EN bit in RxConfig for 8168F-family chips
net: socionext: clear rx irq correctly
net/mlx4_core: Fix warnings during boot on driverinit param set failures
tipc: eliminate possible recursive locking detected by LOCKDEP
selftests: udpgso_bench.sh explicitly requires bash
selftests: rtnetlink.sh explicitly requires bash.
qmi_wwan: Added support for Gemalto's Cinterion ALASxx WWAN interface
tipc: queue socket protocol error messages into socket receive buffer
tipc: set link tolerance correctly in broadcast link
net: ipv4: don't let PMTU updates increase route MTU
net: ipv4: update fnhe_pmtu when first hop's MTU changes
net/ipv6: stop leaking percpu memory in fib6 info
rds: RDS (tcp) hangs on sendto() to unresponding address
net: make skb_partial_csum_set() more robust against overflows
devlink: Add helper function for safely copy string param
devlink: Fix param cmode driverinit for string type
devlink: Fix param set handling for string type
...
|
|
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c29 ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Trace events are useful for people who collect data from the
Ftrace outputs. There're people who analyse the relationship
of cpufreq, thermal and hwmon (power/voltage/current) using
the convenient and timestamped Ftrace outputs, while unlike
cpufreq and thermal subsystems the hwmon does not have trace
events supported yet.
So this patch adds initial trace events for the hwmon core.
To call hwmon_attr_base() for aligned attr index numbers, it
also moves the function upward.
Ftrace outputs:
...: hwmon_attr_show_string: index=2, attr_name=in2_label, val=VDD_5V
...: hwmon_attr_show: index=2, attr_name=in2_input, val=5112
...: hwmon_attr_show: index=2, attr_name=curr2_input, val=440
Note that the _attr_show and _attr_store functions are tied
to the _with_info API. So a hwmon driver requiring the trace
events feature should use _with_info API to register a hwmon
device.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Please note that below oops is from an older kernel, but the same
race seems to be present in the upstream kernel too.
---8<---
The following panic was encountered during removing the ipmi_ssif
module:
[ 526.352555] Unable to handle kernel paging request at virtual address ffff000006923090
[ 526.360464] Mem abort info:
[ 526.363257] ESR = 0x86000007
[ 526.366304] Exception class = IABT (current EL), IL = 32 bits
[ 526.372221] SET = 0, FnV = 0
[ 526.375269] EA = 0, S1PTW = 0
[ 526.378405] swapper pgtable: 4k pages, 48-bit VAs, pgd = 000000008ae60416
[ 526.385185] [ffff000006923090] *pgd=000000bffcffe803, *pud=000000bffcffd803, *pmd=0000009f4731a003, *pte=0000000000000000
[ 526.396141] Internal error: Oops: 86000007 [#1] SMP
[ 526.401008] Modules linked in: nls_iso8859_1 ipmi_devintf joydev input_leds ipmi_msghandler shpchp sch_fq_codel ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear i2c_smbus hid_generic usbhid uas hid usb_storage ast aes_ce_blk i2c_algo_bit aes_ce_cipher qede ttm crc32_ce ptp crct10dif_ce drm_kms_helper ghash_ce syscopyarea sha2_ce sysfillrect sysimgblt pps_core fb_sys_fops sha256_arm64 sha1_ce mpt3sas qed drm raid_class ahci scsi_transport_sas libahci gpio_xlp i2c_xlp9xx aes_neon_bs aes_neon_blk crypto_simd cryptd aes_arm64 [last unloaded: ipmi_ssif]
[ 526.468085] CPU: 125 PID: 0 Comm: swapper/125 Not tainted 4.15.0-35-generic #38~lp1775396+build.1
[ 526.476942] Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL022 08/14/2018
[ 526.484932] pstate: 00400009 (nzcv daif +PAN -UAO)
[ 526.489713] pc : 0xffff000006923090
[ 526.493198] lr : call_timer_fn+0x34/0x178
[ 526.497194] sp : ffff000009b0bdd0
[ 526.500496] x29: ffff000009b0bdd0 x28: 0000000000000082
[ 526.505796] x27: 0000000000000002 x26: ffff000009515188
[ 526.511096] x25: ffff000009515180 x24: ffff0000090f1018
[ 526.516396] x23: ffff000009519660 x22: dead000000000200
[ 526.521696] x21: ffff000006923090 x20: 0000000000000100
[ 526.526995] x19: ffff809eeb466a40 x18: 0000000000000000
[ 526.532295] x17: 000000000000000e x16: 0000000000000007
[ 526.537594] x15: 0000000000000000 x14: 071c71c71c71c71c
[ 526.542894] x13: 0000000000000000 x12: 0000000000000000
[ 526.548193] x11: 0000000000000001 x10: ffff000009b0be88
[ 526.553493] x9 : 0000000000000000 x8 : 0000000000000005
[ 526.558793] x7 : ffff80befc1f8528 x6 : 0000000000000020
[ 526.564092] x5 : 0000000000000040 x4 : 0000000020001b20
[ 526.569392] x3 : 0000000000000000 x2 : ffff809eeb466a40
[ 526.574692] x1 : ffff000006923090 x0 : ffff809eeb466a40
[ 526.579992] Process swapper/125 (pid: 0, stack limit = 0x000000002eb50acc)
[ 526.586854] Call trace:
[ 526.589289] 0xffff000006923090
[ 526.592419] expire_timers+0xc8/0x130
[ 526.596070] run_timer_softirq+0xec/0x1b0
[ 526.600070] __do_softirq+0x134/0x328
[ 526.603726] irq_exit+0xc8/0xe0
[ 526.606857] __handle_domain_irq+0x6c/0xc0
[ 526.610941] gic_handle_irq+0x84/0x188
[ 526.614679] el1_irq+0xe8/0x180
[ 526.617822] cpuidle_enter_state+0xa0/0x328
[ 526.621993] cpuidle_enter+0x34/0x48
[ 526.625564] call_cpuidle+0x44/0x70
[ 526.629040] do_idle+0x1b8/0x1f0
[ 526.632256] cpu_startup_entry+0x2c/0x30
[ 526.636174] secondary_start_kernel+0x11c/0x130
[ 526.640694] Code: bad PC value
[ 526.643800] ---[ end trace d020b0b8417c2498 ]---
[ 526.648404] Kernel panic - not syncing: Fatal exception in interrupt
[ 526.654778] SMP: stopping secondary CPUs
[ 526.658734] Kernel Offset: disabled
[ 526.662211] CPU features: 0x5800c38
[ 526.665688] Memory Limit: none
[ 526.668768] ---[ end Kernel panic - not syncing: Fatal exception in interrupt
Prevent mod_timer from arming a timer that was already removed by
del_timer during module unload.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Cc: <stable@vger.kernel.org> # 3.19
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Florian Fainelli says:
====================
net: dsa: bcm_sf2: Couple of fixes
Here are two fixes for the bcm_sf2 driver that were found during
testing unbind and analysing another issue during system
suspend/resume.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c9c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb8e ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enabling both CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y and
CONFIG_GCOV_PROFILE_ALL=y results in linker warnings:
warning: orphan section `.data..LPBX1' being placed in
section `.data..LPBX1'.
LD_DEAD_CODE_DATA_ELIMINATION adds compiler flag -fdata-sections. This
option causes GCC to create separate data sections for data objects,
including those generated by GCC internally for gcov profiling. The
names of these objects start with a dot (.LPBX0, .LPBX1), resulting in
section names starting with 'data..'.
As section names starting with 'data..' are used for specific purposes
in the Linux kernel, the linker script does not automatically include
them in the output data section, resulting in the "orphan section"
linker warnings.
Fix this by specifically including sections named "data..LPBX*" in the
data section.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
Enabling CONFIG_GCOV_PROFILE_ALL=y causes linker errors on ARM:
`.text.exit' referenced in section `.ARM.exidx.text.exit':
defined in discarded section `.text.exit'
`.text.exit' referenced in section `.fini_array.00100':
defined in discarded section `.text.exit'
And related errors on NDS32:
`.text.exit' referenced in section `.dtors.65435':
defined in discarded section `.text.exit'
The gcov compiler flags cause certain compiler versions to generate
additional destructor-related sections that are not yet handled by the
linker script, resulting in references between discarded and
non-discarded sections.
Since destructors are not used in the Linux kernel, fix this by
discarding these additional sections.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Greentime Hu <green.hu@gmail.com>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
This function was renamed in commit 82fe39a6bc7b ("i2c: refactor
function to release a DMA safe buffer") but this kernel doc wasn't
updated to point at the new function. Rename it.
Fixes: 82fe39a6bc7b ("i2c: refactor function to release a DMA safe buffer")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch implements the 'pattern_set'and 'pattern_clear'
interfaces to support SC27XX LED breathing mode.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.c>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
This patch adds a new LED trigger that LED device can configure
to employ software or hardware pattern engine.
Consumers can write 'pattern' file to enable the software pattern
which alters the brightness for the specified duration with one
software timer.
Moreover consumers can write 'hw_pattern' file to enable the hardware
pattern for some LED controllers which can autonomously control
brightness over time, according to some preprogrammed hardware
patterns.
Signed-off-by: Raphael Teysseyre <rteysseyre@gmail.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Tetsuo brought to my attention that I screwed up the scale_up/scale_down
helpers when I factored out the rq-qos code. We need to wake up all the
waiters when we add slots for requests to make, not when we shrink the
slots. Otherwise we'll end up things waiting forever. This was a
mistake and simply puts everything back the way it was.
cc: stable@vger.kernel.org
Fixes: a79050434b45 ("blk-rq-qos: refactor out common elements of blk-wbt")
eported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The sfp_mutex variable is defined but never used in this file. Not even
in the commit that introduced that variable.
Remove sfp_mutex, it has no purpose.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been reported that since
commit 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
at least RTL_GIGA_MAC_VER_38 NICs work erratically after a resume from
suspend.
The problem has been traced to a missing RX_MULTI_EN bit in the RxConfig
register.
We already set this bit for RTL_GIGA_MAC_VER_35 NICs of the same 8168F
chip family so let's do it also for its other siblings: RTL_GIGA_MAC_VER_36
and RTL_GIGA_MAC_VER_38.
Curiously, the NIC seems to work fine after a system boot without having
this bit set as long as the system isn't suspended and resumed.
Fixes: 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 63ae7949e94a ("net: socionext: Use descriptor info instead of MMIO reads on Rx")
removed constant mmio reads from the driver and started using a descriptor
field to check if packet should be processed.
This lead the napi rx handler being constantly called while no packets
needed processing and ksoftirq getting 100% cpu usage. Issue one mmio read
to clear the irq correcty after processing packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BFQ is already doing a similar thing in its .pd_offline_fn() method
implementation.
While it seems that after commit 4c6994806f70
("blk-throttle: fix race between blkcg_bio_issue_check() and cgroup_rmdir()")
was reverted leaving these pointers intact no longer causes crashes
clearing them is still a sensible thing to do to make the code more robust.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
