| Age | Commit message (Collapse) | Author |
|---|
|
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add WM8962 codec connected to SAI1 interface.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i2c io expander support for imx943 evk board.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add lpi2c and i2c-mux support for imx943 evk board.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add micfil and mqs device nodes
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The RTC module on S32G2/S32G3 based SoCs is used as a wakeup source from
system suspend.
Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@oss.nxp.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
S32G3 and S32G2 have the same 6 SPI devices, add the DT entries. Devices
are all the same except spi0 has 8 chip selects instead of 5. Clock
settings for the chip rely on ATF Firmware [1].
[1]: https://github.com/nxp-auto-linux/arm-trusted-firmware
Co-developed-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Set ethernet1 alias to EQOS interface on phyBOARD-Segin-i.MX93 marking
it the secondary networking interface. The primary ethernet0 interface
is already set by the SoM include file (imx93-phycore-som.dtsi).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move alias for ethernet0 interface to the phyCORE-i.MX93 SoM include
file. The reason behind it is that the physical location of the PHY chip
connected to FEC interface is on the SoM itself and alias thus belongs
into the SoM device-tree. Consequently, it can be used by all boards
based on the phyCORE-i.MX93 SoM (phyBOARD-Segin and phyBOARD-Nash).
This also enables us to mark FEC interface as the primary / first for
networking in the bootloader and systemd (predictable interface names).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable EASRC support in tlv320aic32x4 sound card.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable EASRC support in tlv320aic32x4 sound card.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the BOE av123z7m-n17 variant of the Moduline Display, this variant
comes with a 12.3" 1920x720 display.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the BOE av101hdt-a10 variant of the Moduline Display, this variant
comes with a 10.1 1280x720 display with a touchscreen (not working in
mainline).
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Moduline Display platform is a part of the wider GOcontroll Moduline
ecosystem. These are embedded controllers that focus on modularity with
their swappable IO modules.
The base Moduline Display board includes a board-to-board connector with
various busses to enable adding new display types required by the
application. It includes 2 Moduline IO module slots, a simple mono
codec/amplifier, a four channel adc, 2 CAN busses, an RTC and optional
wifi/bluetooth.
busses to the display adapter include:
- 4 lane LVDS
- 4 lane MIPI-DSI
- 4 lane MIPI-CSI
- HDMI 2.0a
- USB 2.0
- I2S
- I2C
- SPI
Also a couple of GPIO and PWM pins for controlling various ICs on the
display adapter board.
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Ka-Ro Electronics tx8p-ml81 is a COM based on the imx8mp SOC. It has
2 GB of ram and 8 GB of eMMC storage on board.
Add it to enable boards based on this Module
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Currently to configure each IOMUXC_SW_PAD_CTL_PAD the raw value of this
register is written in the dts, these values are not obvious. Add defines
which describe the fields of this register which can be or-ed together to
produce readable settings.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
After commit da5dd31efd24 ("gpio: vf610: Switch to gpio-mmio"),
the vf610 GPIO driver no longer uses the static number 32 for
gc->ngpio. This allows users to configure the number of GPIOs
per port.
And some gpio controllers did have less pads. So add 'ngpios' here,
this can save some memory when request bitmap, and also show user
more accurate information when use gpio tools.
Besides, some gpio controllers have hole in the gpio ranges, so use
'gpio-reserved-ranges' to cover that, then the gpioinfo tool show the
correct result.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Starting with commit e6ef4f8ede09f ("gpio: vf610: make irq_chip immutable")
gpio-vf610 supports locking GPIO being used for IRQ. This already prevents
configuring the GPIO as output, so there is no need for a GPIO hog.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
TQMa9352 is only using LPDDR4X, so the BUCK2 regulator should be fixed
at 600MV.
Fixes: d2858e6bd36c ("arm64: dts: freescale: imx93-tqma9352: Add PMIC node")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Hook up the gpu as a passive cooling device to the thermal zones' alert
trip point just like the cpu.
The gpu here consists of 3D GPU, 2D GPU and NPU.
One way to test would be to set one "alert" trip point low enough
and watch the cooling device state increase:
echo 10000 > /sys/class/thermal/thermal_zone0/trip_point_0_temp
watch cat /sys/class/thermal/cooling_device*/cur_state
And of course set the trip point back to its original value and watch
the cooling device states jump to 0 again.
Signed-off-by: Martin Kepplinger-Novaković <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
I.MX95 I3C only need two clocks so add clock fix. Add "nxp,imx95-i3c"
compatible string for all imx95 i3c nodes.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Add initial DMR support, which required smarter RAPL probe
- Fix AMD MSR RAPL energy reporting
- Add RAPL power limit configuration output
- Minor fixes
* tag 'turbostat-2025.06.08' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: version 2025.06.08
tools/power turbostat: Add initial support for BartlettLake
tools/power turbostat: Add initial support for DMR
tools/power turbostat: Dump RAPL sysfs info
tools/power turbostat: Avoid probing the same perf counters
tools/power turbostat: Allow probing RAPL with platform_features->rapl_msrs cleared
tools/power turbostat: Clean up add perf/msr counter logic
tools/power turbostat: Introduce add_msr_counter()
tools/power turbostat: Remove add_msr_perf_counter_()
tools/power turbostat: Remove add_cstate_perf_counter_()
tools/power turbostat: Remove add_rapl_perf_counter_()
tools/power turbostat: Quit early for unsupported RAPL counters
tools/power turbostat: Always check rapl_joules flag
tools/power turbostat: Fix AMD package-energy reporting
tools/power turbostat: Fix RAPL_GFX_ALL typo
tools/power turbostat: Add Android support for MSR device handling
tools/power turbostat.8: pm_domain wording fix
tools/power turbostat.8: fix typo: idle_pct should be pct_idle
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer cleanup from Thomas Gleixner:
"The delayed from_timer() API cleanup:
The renaming to the timer_*() namespace was delayed due massive
conflicts against Linux-next. Now that everything is upstream finish
the conversion"
* tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide, timers: Rename from_timer() to timer_container_of()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Cure IO bitmap inconsistencies
A failed fork cleans up all resources of the newly created thread
via exit_thread(). exit_thread() invokes io_bitmap_exit() which
does the IO bitmap cleanups, which unfortunately assume that the
cleanup is related to the current task, which is obviously bogus.
Make it work correctly
- A lockdep fix in the resctrl code removed the clearing of the
command buffer in two places, which keeps stale error messages
around. Bring them back.
- Remove unused trace events"
* tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/resctrl: Restore the rdt_last_cmd_clear() calls after acquiring rdtgroup_mutex
x86/iopl: Cure TIF_IO_BITMAP inconsistencies
x86/fpu: Remove unused trace events
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"Add the missing seq_file forward declaration in the timer namespace
header"
* tag 'timers-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timens: Add struct seq_file forward declaration
|
|
Add initial DMR support, which required smarter RAPL probe
Fix AMD MSR RAPL energy reporting
Add RAPL power limit configuration output
Minor fixes
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add initial support for BartlettLake.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add initial support for DMR.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
for example:
intel-rapl:1: psys 28.0s:100W 976.0us:100W
intel-rapl:0: package-0 28.0s:57W,max:15W 2.4ms:57W
intel-rapl:0/intel-rapl:0:0: core disabled
intel-rapl:0/intel-rapl:0:1: uncore disabled
intel-rapl-mmio:0: package-0 28.0s:28W,max:15W 2.4ms:57W
[lenb: simplified format]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
squish me
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
For the RAPL package energy status counter, Intel and AMD share the same
perf_subsys and perf_name, but with different MSR addresses.
Both rapl_counter_arch_infos[0] and rapl_counter_arch_infos[1] are
introduced to describe this counter for different Vendors.
As a result, the perf counter is probed twice, and causes a failure in
in get_rapl_counters() because expected_read_size and actual_read_size
don't match.
Fix the problem by skipping the already probed counter.
Note, this is not a perfect fix. For example, if different
vendors/platforms use the same MSR value for different purpose, the code
can be fooled when it probes a rapl_counter_arch_infos[] entry that does
not belong to the running Vendor/Platform.
In a long run, better to put rapl_counter_arch_infos[] into the
platform_features so that this becomes Vendor/Platform specific.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
cleared
platform_features->rapl_msrs describes the RAPL MSRs supported. While
RAPL Perf counters can be exposed from different kernel backend drivers,
e.g. RAPL MSR I/F driver, or RAPL TPMI I/F driver.
Thus, turbostat should first blindly probe all the available RAPL Perf
counters, and falls back to the RAPL MSR counters if they are listed in
platform_features->rapl_msrs.
With this, platforms that don't have RAPL MSRs can clear the
platform_features->rapl_msrs bits and use RAPL Perf counters only.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Increase the code readability by moving the no_perf/no_msr flag and the
cai->perf_name/cai->msr sanity checks into the counter probe functions.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
probe_rapl_msr() is reused for probing RAPL MSR counters, cstate MSR
counters and MPERF/APERF/SMI MSR counters, thus its name is misleading.
Similar to add_perf_counter(), introduce add_msr_counter() to probe a
counter via MSR. Introduce wrapper function add_rapl_msr_counter() at
the same time to add extra check for Zero return value for specified
RAPL counters.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
As the only caller of add_msr_perf_counter_(), add_msr_perf_counter()
just gives extra debug output on top. There is no need to keep both
functions.
Remove add_msr_perf_counter_() and move all the logic to
add_msr_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
As the only caller of add_cstate_perf_counter_(),
add_cstate_perf_counter() just gives extra debug output on top. There is
no need to keep both functions.
Remove add_cstate_perf_counter_() and move all the logic to
add_cstate_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
As the only caller of add_rapl_perf_counter_(), add_rapl_perf_counter()
just gives extra debug output on top. There is no need to keep both
functions.
Remove add_rapl_perf_counter_() and move all the logic to
add_rapl_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Quit early for unsupported RAPL counters.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
rapl_joules bit should always be checked even if
platform_features->rapl_msrs is not set or no_msr flag is used.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
commit 05a2f07db888 ("tools/power turbostat: read RAPL counters via
perf") that adds support to read RAPL counters via perf defines the
notion of a RAPL domain_id which is set to physical_core_id on
platforms which support per_core_rapl counters (Eg: AMD processors
Family 17h onwards) and is set to the physical_package_id on all the
other platforms.
However, the physical_core_id is only unique within a package and on
platforms with multiple packages more than one core can have the same
physical_core_id and thus the same domain_id. (For eg, the first cores
of each package have the physical_core_id = 0). This results in all
these cores with the same physical_core_id using the same entry in the
rapl_counter_info_perdomain[]. Since rapl_perf_init() skips the
perf-initialization for cores whose domain_ids have already been
visited, cores that have the same physical_core_id always read the
perf file corresponding to the physical_core_id of the first package
and thus the package-energy is incorrectly reported to be the same
value for different packages.
Note: This issue only arises when RAPL counters are read via perf and
not when they are read via MSRs since in the latter case the MSRs are
read separately on each core.
Fix this issue by associating each CPU with rapl_core_id which is
unique across all the packages in the system.
Fixes: 05a2f07db888 ("tools/power turbostat: read RAPL counters via perf")
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Fix typo in the currently unused RAPL_GFX_ALL macro definition.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
It uses /dev/msrN device paths on Android instead of /dev/cpu/N/msr,
updates error messages and permission checks to reflect the Android
device path, and wraps platform-specific code with #if defined(ANDROID)
to ensure correct behavior on both Android and non-Android systems.
These changes improve compatibility and usability of turbostat on
Android devices.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
turbostat.8: clarify that uncore "domains" are Power Management domains,
aka pm_domains.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
idle_pct should be pct_idle
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 perf fix from Thomas Gleixner:
"A single fix for the x86 performance counters on Intel CPUs:
The MSR offset calculations for fixed performance counters are stored
at the wrong index in the configuration array causing the general
purpose counter MSR offset to be overwritten, so both the general
purpose and the fixed counters offsets are incorrect.
Correct the array index calculation to fix that"
* tag 'perf-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Fix incorrect MSR index calculations in intel_pmu_config_acr()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for the PCI/MSI code:
The conversion to per device MSI domains created a MSI domain with
size 1 instead of sizing it to the maximum possible number of MSI
interrupts for the device. This "worked" as the subsequent allocations
resized the domain, but the recent change to move the prepare() call
into the domain creation path broke this works by chance mechanism.
Size the domain properly at creation time"
* tag 'irq-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Size device MSI domain with the maximum number of vectors
|
|
Pull mount fixes from Al Viro:
"Various mount-related bugfixes:
- split the do_move_mount() checks in subtree-of-our-ns and
entire-anon cases and adapt detached mount propagation selftest for
mount_setattr
- allow clone_private_mount() for a path on real rootfs
- fix a race in call of has_locked_children()
- fix move_mount propagation graph breakage by MOVE_MOUNT_SET_GROUP
- make sure clone_private_mnt() caller has CAP_SYS_ADMIN in the right
userns
- avoid false negatives in path_overmount()
- don't leak MNT_LOCKED from parent to child in finish_automount()
- do_change_type(): refuse to operate on unmounted/not ours mounts"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
do_change_type(): refuse to operate on unmounted/not ours mounts
clone_private_mnt(): make sure that caller has CAP_SYS_ADMIN in the right userns
selftests/mount_setattr: adapt detached mount propagation test
do_move_mount(): split the checks in subtree-of-our-ns and entire-anon cases
fs: allow clone_private_mount() for a path on real rootfs
fix propagation graph breakage by MOVE_MOUNT_SET_GROUP move_mount(2)
finish_automount(): don't leak MNT_LOCKED from parent to child
path_overmount(): avoid false negatives
fs/fhandle.c: fix a race in call of has_locked_children()
|
|
git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- multichannel/reconnect fixes
- move smbdirect (smb over RDMA) defines to fs/smb/common so they will
be able to be used in the future more broadly, and a documentation
update explaining setting up smbdirect mounts
- update email address for Paulo
* tag '6.16-rc-part2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
MAINTAINERS, mailmap: Update Paulo Alcantara's email address
cifs: add documentation for smbdirect setup
cifs: do not disable interface polling on failure
cifs: serialize other channels when query server interfaces is pending
cifs: deal with the channel loading lag while picking channels
smb: client: make use of common smbdirect_socket_parameters
smb: smbdirect: introduce smbdirect_socket_parameters
smb: client: make use of common smbdirect_socket
smb: smbdirect: add smbdirect_socket.h
smb: client: make use of common smbdirect.h
smb: smbdirect: add smbdirect.h with public structures
smb: client: make use of common smbdirect_pdu.h
smb: smbdirect: add smbdirect_pdu.h with protocol definitions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull more tracing fixes from Steven Rostedt:
- Fix regression of waiting a long time on updating trace event filters
When the faultable trace points were added, it needed task trace RCU
synchronization.
This was added to the tracepoint_synchronize_unregister() function.
The filter logic always called this function whenever it updated the
trace event filters before freeing the old filters. This increased
the time of "trace-cmd record" from taking 13 seconds to running over
2 minutes to complete.
Move the freeing of the filters to call_rcu*() logic, which brings
the time back down to 13 seconds.
- Fix ring_buffer_subbuf_order_set() error path lock protection
The error path of the ring_buffer_subbuf_order_set() released the
mutex too early and allowed subsequent accesses to setting the
subbuffer size to corrupt the data and cause a bug.
By moving the mutex locking to the end of the error path, it prevents
the reentrant access to the critical data and also allows the
function to convert the taking of the mutex over to the guard()
logic.
- Remove unused power management clock events
The clock events were added in 2010 for power management. In 2011 arm
used them. In 2013 the code they were used in was removed. These
events have been wasting memory since then.
- Fix sparse warnings
There was a few places that sparse warned about trace_events_filter.c
where file->filter was referenced directly, but it is annotated with
an __rcu tag. Use the helper functions and fix them up to use
rcu_dereference() properly.
* tag 'trace-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Add rcu annotation around file->filter accesses
tracing: PM: Remove unused clock events
ring-buffer: Fix buffer locking in ring_buffer_subbuf_order_set()
tracing: Fix regression of filter waiting a long time on RCU synchronization
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
