| Age | Commit message (Collapse) | Author |
|---|
|
MAINTAINERS still pointed to phy.txt after moving this file into the rst
format, fix this.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 25fe02d00a1e ("Documentation: net: phy: switch documentation to rst format")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christoph reported a stall while peeking datagram with an offset when
busy polling is enabled. __skb_try_recv_datagram() uses as the loop
termination condition 'queue empty'. When peeking, the socket
queue can be not empty, even when no additional packets are received.
Address the issue explicitly checking for receive queue changes,
as currently done by __skb_wait_for_more_packets().
Fixes: 2b5cd0dfa384 ("net: Change return type of sk_busy_loop from bool to void")
Reported-and-tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[Why]
VBIOS will not post pixel rate > 340MHz.
If driver set pixel rate > 340MHz and do restart bottom, VBIOS can't
post HDMI monitor due to monitor is stay in HDMI2.0 state.
[How]
Program Scrambling_Enable and TMDS_Bit_Clock_Ratio when disable stream.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If DAL requires to force MCLK high, the FCLK will be
forced to high also.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Avoid left shift overflow.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's OK to have this feature bit with old SMU firmwares.
But the feature should be disabled on them.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
use pcie_bandwidth_available to get real link state
to update pcie table.
v2: fix incorrect initialized return value
v3: expand the fetching method about the link width to all asics.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No change to functionality. Simply make transport event messages a little
clearer, and rework CRQ format enums such that we have separate enums for
INIT messages and XPORT events.
[mkp: typo]
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Status and error codes are returned in big endian from the VIOS. The values
are translated into a human readable format when logged, but the values are
also logged. This patch byte swaps those values so that they are consistent
between BE and LE platforms.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The VIOS uses the SCSI_ERROR class to report PRLI failures. These errors
are indicated with the combination of a IBMVFC_FC_SCSI_ERROR return status
and 0x8000 error code. Add these codes to cmd_status[] with appropriate
human readable error message.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The text of messages logged with ibmvfc_log_error() always contain the term
"failed". In the case of cancelled commands during EH they are reported
back by the VIOS using error codes. This can be confusing to somebody
looking at these log messages as to whether a command was successfully
cancelled. The following real log message for example it is unclear if the
transaction was actaully cancelled.
<6>sd 0:0:1:1: Cancelling outstanding commands.
<3>sd 0:0:1:1: [sde] Command (28) failed: transaction cancelled (2:6) flags: 0 fcp_rsp: 0, resid=0, scsi_status: 0
Remove prefixing of "failed" to all error logged messages. The
ibmvfc_log_error() function translates the returned error/status codes to a
human readable message already.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away. It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.
The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.
The call chain was:
zfcp_fc_incoming_rscn
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:
zfcp_fc_incoming_rscn
if (no_entries > 1) <===
list_for_each_entry(port, &adapter->port_list, list) <===
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
Abbreviated example trace records before this code change:
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x02
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x00 NOP => superfluous trace record
The last trace entry repeats if there are more than 2 RSCN elements.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit
ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org> #3.0+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery")
Cc: <stable@vger.kernel.org> #2.6.32+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes: a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size")
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Reported-by: Hussam Al-Tayeb <ht990332@gmx.com>
Tested-by: Hussam Al-Tayeb <ht990332@gmx.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
scsi_mq_uninit_cmd+0x1c/0x30
scsi_end_request+0x7c/0x1b8
scsi_io_completion+0x464/0x668
scsi_finish_command+0xbc/0x160
scsi_eh_flush_done_q+0x10c/0x170
sas_scsi_recover_host+0x84c/0xa98 [libsas]
scsi_error_handler+0x140/0x5b0
kthread+0x100/0x12c
ret_from_fork+0x10/0x18
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use dd to test a SCSI device:
1. echo "blocked" >/sys/block/sda/device/state
2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10
3. echo "running" >/sys/block/sda/device/state
dd should finish this work after step 3, but it hangs.
After step2, the call chain is this:
blk_mq_dispatch_rq_list-->scsi_queue_rq-->prep_to_mq
prep_to_mq will return BLK_STS_RESOURCE, and scsi_queue_rq will
transition it to BLK_STS_DEV_RESOURCE which means that driver can
guarantee that IO dispatch will be triggered in future when the
resource is available. Need to follow the rule if we set the device
state to running.
[mkp: tweaked commit description and code comment as suggested by Bart]
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull networking fixes from David Miller:
"Fixes here and there, a couple new device IDs, as usual:
1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.
2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.
3) Fix documentation for some eBPF helpers, from Quentin Monnet.
4) Some UAPI bpf header sync with tools, also from Quentin Monnet.
5) Set descriptor ownership bit at the right time for jumbo frames in
stmmac driver, from Aaro Koskinen.
6) Set IFF_UP properly in tun driver, from Eric Dumazet.
7) Fix load/store doubleword instruction generation in powerpc eBPF
JIT, from Naveen N. Rao.
8) nla_nest_start() return value checks all over, from Kangjie Lu.
9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
merge window. From Marcelo Ricardo Leitner and Xin Long.
10) Fix memory corruption with large MTUs in stmmac, from Aaro
Koskinen.
11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
Dumazet.
12) Fix topology subscription cancellation in tipc, from Erik Hugne.
13) Memory leak in genetlink error path, from Yue Haibing.
14) Valid control actions properly in packet scheduler, from Davide
Caratti.
15) Even if we get EEXIST, we still need to rehash if a shrink was
delayed. From Herbert Xu.
16) Fix interrupt mask handling in interrupt handler of r8169, from
Heiner Kallweit.
17) Fix leak in ehea driver, from Wen Yang"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
dpaa2-eth: fix race condition with bql frame accounting
chelsio: use BUG() instead of BUG_ON(1)
net: devlink: skip info_get op call if it is not defined in dumpit
net: phy: bcm54xx: Encode link speed and activity into LEDs
tipc: change to check tipc_own_id to return in tipc_net_stop
net: usb: aqc111: Extend HWID table by QNAP device
net: sched: Kconfig: update reference link for PIE
net: dsa: qca8k: extend slave-bus implementations
net: dsa: qca8k: remove leftover phy accessors
dt-bindings: net: dsa: qca8k: support internal mdio-bus
dt-bindings: net: dsa: qca8k: fix example
net: phy: don't clear BMCR in genphy_soft_reset
bpf, libbpf: clarify bump in libbpf version info
bpf, libbpf: fix version info and add it to shared object
rxrpc: avoid clang -Wuninitialized warning
tipc: tipc clang warning
net: sched: fix cleanup NULL pointer exception in act_mirr
r8169: fix cable re-plugging issue
net: ethernet: ti: fix possible object reference leak
net: ibm: fix possible object reference leak
...
|
|
If we use "crashkernel=Y[@X]" and the start address is above 4G,
the arm64 kdump capture kernel may call memblock_alloc_low() failure
in request_standard_resources(). Replacing memblock_alloc_low() with
memblock_alloc().
[ 0.000000] MEMBLOCK configuration:
[ 0.000000] memory size = 0x0000000040650000 reserved size = 0x0000000004db7f39
[ 0.000000] memory.cnt = 0x6
[ 0.000000] memory[0x0] [0x00000000395f0000-0x000000003968ffff], 0x00000000000a0000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x1] [0x0000000039730000-0x000000003973ffff], 0x0000000000010000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x2] [0x0000000039780000-0x000000003986ffff], 0x00000000000f0000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x3] [0x0000000039890000-0x0000000039d0ffff], 0x0000000000480000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x4] [0x000000003ed00000-0x000000003ed2ffff], 0x0000000000030000 bytes on node 0 flags: 0x4
[ 0.000000] memory[0x5] [0x0000002040000000-0x000000207fffffff], 0x0000000040000000 bytes on node 0 flags: 0x0
[ 0.000000] reserved.cnt = 0x7
[ 0.000000] reserved[0x0] [0x0000002040080000-0x0000002041c4dfff], 0x0000000001bce000 bytes flags: 0x0
[ 0.000000] reserved[0x1] [0x0000002041c53000-0x0000002042c203f8], 0x0000000000fcd3f9 bytes flags: 0x0
[ 0.000000] reserved[0x2] [0x000000207da00000-0x000000207dbfffff], 0x0000000000200000 bytes flags: 0x0
[ 0.000000] reserved[0x3] [0x000000207ddef000-0x000000207fbfffff], 0x0000000001e11000 bytes flags: 0x0
[ 0.000000] reserved[0x4] [0x000000207fdf2b00-0x000000207fdfc03f], 0x0000000000009540 bytes flags: 0x0
[ 0.000000] reserved[0x5] [0x000000207fdfd000-0x000000207ffff3ff], 0x0000000000202400 bytes flags: 0x0
[ 0.000000] reserved[0x6] [0x000000207ffffe00-0x000000207fffffff], 0x0000000000000200 bytes flags: 0x0
[ 0.000000] Kernel panic - not syncing: request_standard_resources: Failed to allocate 384 bytes
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.1.0-next-20190321+ #4
[ 0.000000] Call trace:
[ 0.000000] dump_backtrace+0x0/0x188
[ 0.000000] show_stack+0x24/0x30
[ 0.000000] dump_stack+0xa8/0xcc
[ 0.000000] panic+0x14c/0x31c
[ 0.000000] setup_arch+0x2b0/0x5e0
[ 0.000000] start_kernel+0x90/0x52c
[ 0.000000] ---[ end Kernel panic - not syncing: request_standard_resources: Failed to allocate 384 bytes ]---
Link: https://www.spinics.net/lists/arm-kernel/msg715293.html
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
free the symlink body after the same RCU delay we have for freeing the
struct inode itself, so that traversal during RCU pathwalk wouldn't step
into freed memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
VirtualBox 6.0.x has a new feature where the guest kernel driver passes
info about the origin of the request (e.g. userspace or kernelspace) to
the hypervisor.
If we do not pass this information then when running the 6.0.x userspace
guest-additions tools on a 6.0.x host, some requests will get denied
with a VERR_VERSION_MISMATCH error, breaking vboxservice.service and
the mounting of shared folders marked to be auto-mounted.
This commit implements passing the requestor info to the host, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unlike 'client_ops' which is initialized to 'default_client_ops', the
port operations 'ops' may be left to NULL.
Check the 'ops' value before checking the 'ops->x' value.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Echo "" to /sys/module/kgdboc/parameters/kgdboc will fail with "No such
device” error.
This is caused by function "configure_kgdboc" who init err to ENODEV
when the config is empty (legal input) the code go out with ENODEV
returned.
Fixes: 2dd453168643 ("kgdboc: Fix restrict error")
Signed-off-by: Wentao Wang <witallwang@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds dt-binding documentation of uart for Mediatek MT8183 SoC
Platform.
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In half-duplex operation, RX should be started after TX completes.
If DMA is used, there is a case when the DMA transfer completes but the
TX FIFO is not emptied, so the RX cannot be restarted just yet.
Use a boolean variable to store this state and rearm TX interrupt mask
to be signaled again that the transfer finished. In interrupt transmit
handler this variable is used to start RX. A warning message is generated
if RX is activated before TX fifo is cleared.
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable
RX after TX is done")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use a helper function to check that a port needs to use half duplex
communication, replacing several occurrences of multi-line bit checking.
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
if platform_driver_register fails, cleanup the allocated resource
gracefully.
Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.
This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.
Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().
Fixes: 1aba579f3cf5 cdc-acm: handle read pipe errors
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Andrii Nakryiko says:
====================
This patch set fixes bug in btf_dedup_is_equiv() check mishandling equivalence
comparison between VOID kind in candidate type graph versus anonymous non-VOID
kind in canonical type graph.
Patch #1 fixes bug, by comparing candidate and canonical kinds for equality,
before proceeding to kind-specific checks.
Patch #2 adds a test case testing this specific scenario.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This patch adds specific test exposing bug in btf_dedup_is_equiv() when
comparing candidate VOID type to a non-VOID canonical type. It's
important for canonical type to be anonymous, otherwise name equality
check will do the right thing and will exit early.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
btf_dedup_is_equiv() used to compare btf_type->info fields, before doing
kind-specific equivalence check. This comparsion implicitly verified
that candidate and canonical types are of the same kind. With enum fwd
resolution logic this check couldn't be done generically anymore, as for
enums info contains vlen, which differs between enum fwd and
fully-defined enum, so this check was subsumed by kind-specific
equivalence checks.
This change caused btf_dedup_is_equiv() to let through VOID vs other
types check to reach switch, which was never meant to be handing VOID
kind, as VOID kind is always pre-resolved to itself and is only
equivalent to itself, which is checked early in btf_dedup_is_equiv().
This change adds back BTF kind equality check in place of more generic
btf_type->info check, still defering further kind-specific checks to
a per-kind switch.
Fixes: 9768095ba97c ("btf: resolve enum fwds in btf_dedup")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Since commit
ad67b74d2469 ("printk: hash addresses printed with %p")
at boot "____ptrval____" is printed instead of the trampoline addresses:
Base memory trampoline at [(____ptrval____)] 99000 size 24576
Remove the print as we don't want to leak kernel addresses and this
statement is not needed anymore.
Fixes: ad67b74d2469d9b8 ("printk: hash addresses printed with %p")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190326203046.20787-1-mcroce@redhat.com
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If we use the "i2c-" prefix for the binding documentation file name,
then it should match the file name of the driver, if possible. It is
possible for this driver, so rename it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Similar to commit edfc3722cfef ("HID: quirks: Fix keyboard + touchpad on
Toshiba Click Mini not working"), the Lenovo Miix 630 has a combo
keyboard/touchpad device with vid:pid of 04F3:0400, which is shared with
Elan touchpads. The combo on the Miix 630 has an ACPI id of QTEC0001,
which is not claimed by the elan_i2c driver, so key on that similar to
what was done for the Toshiba Click Mini.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The declarations related to immovable memory handling are out of the
BOOT_COMPRESSED_MISC_H #ifdef scope, wrap them inside.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Chao Fan <fanc.fnst@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190304055546.18566-1-bhe@redhat.com
|
|
The debugfs read callback must advance ppos or users using read() on
the file descriptor will never get the EOL. This wasn't spotted before
as I was using busybox cat for testing which uses sendfile() internally
and only noticed it now when switched to cat from coreutils.
Fixes: 2a9e27408e12 ("gpio: mockup: rework debugfs interface")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
gpio-aspeed implements support for PIN_CONFIG_INPUT_DEBOUNCE. As of
v5.1-rc1 we're seeing the following when booting a Romulus BMC kernel:
> [ 21.373137] ------------[ cut here ]------------
> [ 21.374545] WARNING: CPU: 0 PID: 1 at drivers/gpio/gpio-aspeed.c:834 unregister_allocated_timer+0x38/0x94
> [ 21.376181] No timer allocated to offset 74
> [ 21.377672] CPU: 0 PID: 1 Comm: swapper Not tainted 5.1.0-rc1-dirty #6
> [ 21.378800] Hardware name: Generic DT based system
> [ 21.379965] Backtrace:
> [ 21.381024] [<80107d44>] (dump_backtrace) from [<80107f78>] (show_stack+0x20/0x24)
> [ 21.382713] r7:8038b720 r6:00000009 r5:00000000 r4:87897c64
> [ 21.383815] [<80107f58>] (show_stack) from [<80656398>] (dump_stack+0x20/0x28)
> [ 21.385042] [<80656378>] (dump_stack) from [<80115f1c>] (__warn.part.3+0xb4/0xdc)
> [ 21.386253] [<80115e68>] (__warn.part.3) from [<80115fb0>] (warn_slowpath_fmt+0x6c/0x90)
> [ 21.387471] r6:00000342 r5:807f8758 r4:80a07008
> [ 21.388278] [<80115f48>] (warn_slowpath_fmt) from [<8038b720>] (unregister_allocated_timer+0x38/0x94)
> [ 21.389809] r3:0000004a r2:807f8774
> [ 21.390526] r7:00000000 r6:0000000a r5:60000153 r4:0000004a
> [ 21.391601] [<8038b6e8>] (unregister_allocated_timer) from [<8038baac>] (aspeed_gpio_set_config+0x330/0x48c)
> [ 21.393248] [<8038b77c>] (aspeed_gpio_set_config) from [<803840b0>] (gpiod_set_debounce+0xe8/0x114)
> [ 21.394745] r10:82ee2248 r9:00000000 r8:87b63a00 r7:00001388 r6:87947320 r5:80729310
> [ 21.396030] r4:879f64a0
> [ 21.396499] [<80383fc8>] (gpiod_set_debounce) from [<804b4350>] (gpio_keys_probe+0x69c/0x8e0)
> [ 21.397715] r7:845d94b8 r6:00000001 r5:00000000 r4:87b63a1c
> [ 21.398618] [<804b3cb4>] (gpio_keys_probe) from [<8040eeec>] (platform_dev_probe+0x44/0x80)
> [ 21.399834] r10:00000003 r9:80a3a8b0 r8:00000000 r7:00000000 r6:80a7f9dc r5:80a3a8b0
> [ 21.401163] r4:8796bc10
> [ 21.401634] [<8040eea8>] (platform_drv_probe) from [<8040d0d4>] (really_probe+0x208/0x3dc)
> [ 21.402786] r5:80a7f8d0 r4:8796bc10
> [ 21.403547] [<8040cecc>] (really_probe) from [<8040d7a4>] (driver_probe_device+0x130/0x170)
> [ 21.404744] r10:0000007b r9:8093683c r8:00000000 r7:80a07008 r6:80a3a8b0 r5:8796bc10
> [ 21.405854] r4:80a3a8b0
> [ 21.406324] [<8040d674>] (driver_probe_device) from [<8040da8c>] (device_driver_attach+0x68/0x70)
> [ 21.407568] r9:8093683c r8:00000000 r7:80a07008 r6:80a3a8b0 r5:00000000 r4:8796bc10
> [ 21.408877] [<8040da24>] (device_driver_attach) from [<8040db14>] (__driver_attach+0x80/0x150)
> [ 21.410327] r7:80a07008 r6:8796bc10 r5:00000001 r4:80a3a8b0
> [ 21.411294] [<8040da94>] (__driver_attach) from [<8040b20c>] (bus_for_each_dev+0x80/0xc4)
> [ 21.412641] r7:80a07008 r6:8040da94 r5:80a3a8b0 r4:87966f30
> [ 21.413580] [<8040b18c>] (bus_for_each_dev) from [<8040dc0c>] (driver_attach+0x28/0x30)
> [ 21.414943] r7:00000000 r6:87b411e0 r5:80a33fc8 r4:80a3a8b0
> [ 21.415927] [<8040dbe4>] (driver_attach) from [<8040bbf0>] (bus_add_driver+0x14c/0x200)
> [ 21.417289] [<8040baa4>] (bus_add_driver) from [<8040e2b4>] (driver_register+0x84/0x118)
> [ 21.418652] r7:80a60ae0 r6:809226b8 r5:80a07008 r4:80a3a8b0
> [ 21.419652] [<8040e230>] (driver_register) from [<8040fc28>] (__platform_driver_register+0x3c/0x50)
> [ 21.421193] r5:80a07008 r4:809525f8
> [ 21.421990] [<8040fbec>] (__platform_driver_register) from [<809226d8>] (gpio_keys_init+0x20/0x28)
> [ 21.423447] [<809226b8>] (gpio_keys_init) from [<8090128c>] (do_one_initcall+0x80/0x180)
> [ 21.424886] [<8090120c>] (do_one_initcall) from [<80901538>] (kernel_init_freeable+0x1ac/0x26c)
> [ 21.426354] r8:80a60ae0 r7:80a60ae0 r6:8093685c r5:00000008 r4:809525f8
> [ 21.427579] [<8090138c>] (kernel_init_freeable) from [<8066d9a0>] (kernel_init+0x18/0x11c)
> [ 21.428819] r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:8066d988
> [ 21.429947] r4:00000000
> [ 21.430415] [<8066d988>] (kernel_init) from [<801010e8>] (ret_from_fork+0x14/0x2c)
> [ 21.431666] Exception stack(0x87897fb0 to 0x87897ff8)
> [ 21.432877] 7fa0: 00000000 00000000 00000000 00000000
> [ 21.434446] 7fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> [ 21.436052] 7fe0: 00000000 00000000 00000000 00000000 00000013 00000000
> [ 21.437308] r5:8066d988 r4:00000000
> [ 21.438102] ---[ end trace d7d7ac3a80567d0e ]---
We only hit unregister_allocated_timer() if the argument to
aspeed_gpio_set_config() is 0, but we can't be calling through
gpiod_set_debounce() from gpio_keys_probe() unless the gpio-keys button has a
non-zero debounce interval.
Commit 6581eaf0e890 ("gpio: use new gpio_set_config() helper in more places")
spreads the use of gpio_set_config() to the debounce and transitory
state configuration paths. The implementation of gpio_set_config() is:
> static int gpio_set_config(struct gpio_chip *gc, unsigned offset,
> enum pin_config_param mode)
> {
> unsigned long config = { PIN_CONF_PACKED(mode, 0) };
>
> return gc->set_config ? gc->set_config(gc, offset, config) : -ENOTSUPP;
> }
Here it packs its own config value with a fixed argument of 0; this is
incorrect behaviour for implementing the debounce and transitory functions, and
the debounce and transitory gpio_set_config() call-sites now have an undetected
type mismatch as they both already pack their own config parameter (i.e. what
gets passed is not an `enum pin_config_param`). Indeed this can be seen in the
small diff for 6581eaf0e890:
> diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
> index de595fa31a1a..1f239aac43df 100644
> --- a/drivers/gpio/gpiolib.c
> +++ b/drivers/gpio/gpiolib.c
> @@ -2725,7 +2725,7 @@ int gpiod_set_debounce(struct gpio_desc *desc, unsigned debounce)
> }
>
> config = pinconf_to_config_packed(PIN_CONFIG_INPUT_DEBOUNCE, debounce);
> - return chip->set_config(chip, gpio_chip_hwgpio(desc), config);
> + return gpio_set_config(chip, gpio_chip_hwgpio(desc), config);
> }
> EXPORT_SYMBOL_GPL(gpiod_set_debounce);
>
> @@ -2762,7 +2762,7 @@ int gpiod_set_transitory(struct gpio_desc *desc, bool transitory)
> packed = pinconf_to_config_packed(PIN_CONFIG_PERSIST_STATE,
> !transitory);
> gpio = gpio_chip_hwgpio(desc);
> - rc = chip->set_config(chip, gpio, packed);
> + rc = gpio_set_config(chip, gpio, packed);
> if (rc == -ENOTSUPP) {
> dev_dbg(&desc->gdev->dev, "Persistence not supported for GPIO %d\n",
> gpio);
Revert commit 6581eaf0e890 ("gpio: use new gpio_set_config() helper in
more places") to restore correct behaviour for gpiod_set_debounce() and
gpiod_set_transitory().
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The live_context() function returns error pointers. It never returns
NULL.
Fixes: 9c1477e83e62 ("drm/i915/selftests: Exercise adding requests to a full GGTT")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326050843.GA20038@kadam
(cherry picked from commit 602cbe8efc523ba56e1f41e8f74c7aa835672593)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The Linux RISC-V 32bit kernel is broken after we moved setup_vm() from
kernel/setup.c to mm/init.c because Linux RISC-V 32bit kernel by default
uses cmodel=medlow which results in a non-position-independent setup_vm().
This patch fixes Linux RISC-V 32bit kernel booting by:
1. Forcing cmodel=medany for mm/init.c
2. Moving remaing MM-related stuff va_pa_offset, pfn_base and
empty_zero_page from kernel/setup.c to mm/init.c
Further, the setup_vm() cannot handle GCC instrumentation for FTRACE so
we disable it for mm/init.c by not using "-pg" compiler flag.
Fixes: 6f1e9e946f0b ("RISC-V: Move setup_vm() to mm/init.c")
Suggested-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
A memory save operation to 8-byte variable in RV32 is divided into
two sw instructions in the put_user macro. The current fixup returns
execution flow to the second sw instead of the one after it.
This patch fixes this fixup code according to the load access part.
Signed-off-by: Alan Kao<alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
In cpu_to_drc_index() in the case when FW_FEATURE_DRC_INFO is absent,
we currently use of_read_property() to obtain the pointer to the array
corresponding to the property "ibm,drc-indexes". The elements of this
array are of type __be32, but are accessed without any conversion to
the OS-endianness, which is buggy on a Little Endian OS.
Fix this by using of_property_read_u32_index() accessor function to
safely read the elements of the array.
Fixes: e83636ac3334 ("pseries/drc-info: Search DRC properties for CPU indexes")
Cc: stable@vger.kernel.org # v4.16+
Reported-by: Pavithra R. Prakash <pavrampu@in.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[mpe: Make the WARN_ON a WARN_ON_ONCE so it's not retriggerable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Syzkaller report this:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN PTI
CPU: 0 PID: 4378 Comm: syz-executor.0 Tainted: G C 5.0.0+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
RIP: 0010:__lock_acquire+0x95b/0x3200 kernel/locking/lockdep.c:3573
Code: 00 0f 85 28 1e 00 00 48 81 c4 08 01 00 00 5b 5d 41 5c 41 5d 41 5e 41 5f c3 4c 89 ea 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 cc 24 00 00 49 81 7d 00 e0 de 03 a6 41 bc 00 00
RSP: 0018:ffff8881e3c07a40 EFLAGS: 00010002
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000010 RSI: 0000000000000000 RDI: 0000000000000080
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8881e3c07d98 R11: ffff8881c7f21f80 R12: 0000000000000001
R13: 0000000000000080 R14: 0000000000000000 R15: 0000000000000001
FS: 00007fce2252e700(0000) GS:ffff8881f2400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fffc7eb0228 CR3: 00000001e5bea002 CR4: 00000000007606f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
lock_acquire+0xff/0x2c0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xdf/0x1050 kernel/locking/mutex.c:1072
drain_workqueue+0x24/0x3f0 kernel/workqueue.c:2934
destroy_workqueue+0x23/0x630 kernel/workqueue.c:4319
__do_sys_delete_module kernel/module.c:1018 [inline]
__se_sys_delete_module kernel/module.c:961 [inline]
__x64_sys_delete_module+0x30c/0x480 kernel/module.c:961
do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x462e99
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fce2252dc58 EFLAGS: 00000246 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000020000140
RBP: 0000000000000002 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fce2252e6bc
R13: 00000000004bcca9 R14: 00000000006f6b48 R15: 00000000ffffffff
If alloc_workqueue fails, it should return -ENOMEM, otherwise may
trigger this NULL pointer dereference while unloading drivers.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0a38c17a21a0 ("fm10k: Remove create_workqueue")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current check for WoL on i40e is broken. Code comment says only
magic packet is supported, so only check for that.
Fixes: 540a152da762 (i40e/ixgbe/igb: fail on new WoL flag setting WAKE_MAGICSECURE)
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The ixgbe ignores errors returned from mdiobus_register() and leaves
adapter->mii_bus non-NULL and MDIO bus state as MDIOBUS_ALLOCATED.
This triggers a BUG from mdiobus_unregister() during ixgbe_remove() call.
Fixes: 8fa10ef01260 ("ixgbe: register a mdiobus")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The runtime_suspend device callbacks are not supposed to save
configuration state or change the power state. Commit fb29f76cc566
("igb: Fix an issue that PME is not enabled during runtime suspend")
changed the driver to not save configuration state during runtime
suspend, however the driver callback still put the device into a
low-power state. This causes a warning in the pci pm core and results in
pci_pm_runtime_suspend not calling pci_save_state or pci_finish_runtime_suspend.
Fix this by not changing the power state either, leaving that to pci pm
core, and make the same change for suspend callback as well.
Also move a couple of defines into the appropriate header file instead
of inline in the .c file.
Fixes: fb29f76cc566 ("igb: Fix an issue that PME is not enabled during runtime suspend")
Signed-off-by: Arvind Sankar <niveditas98@gmail.com>
Reviewed-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
