| Age | Commit message (Collapse) | Author |
|---|
|
Some BIOSes report incorrect length for ACPI address space descriptors,
so relax the checks to avoid regressions. This issue has appeared several
times as:
3162b6f0c5e1 ("PNPACPI: truncate _CRS windows with _LEN > _MAX - _MIN + 1")
d558b483d5a7 ("x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1")
f238b414a74a ("PNPACPI: compute Address Space length rather than using _LEN")
48728e077480 ("x86/PCI: compute Address Space length rather than using _LEN")
Please refer to https://bugzilla.kernel.org/show_bug.cgi?id=94221
for more details and example malformed ACPI resource descriptors.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94221
Fixes: 593669c2ac0f (x86/PCI/ACPI: Use common ACPI resource interfaces ...)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When parsing resources for PCI host bridge, we should ignore resources
consumed by host bridge itself and only report window resources available
to child PCI busses.
Fixes: 593669c2ac0f (x86/PCI/ACPI: Use common ACPI resource interfaces ...)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Below are the refinements.
1. Set DMA abort bit when disabling dma channel. This will clear
the remaining data in dma FIFO, to fix channel-swap issue.
2. Read DMA HW pointer when updating DMA status. Previously dma
position is calculated by adding one period size in dma interrupt.
This is inaccurate/insufficient for some high-quality audio APP.
Since interrupt bottom half handler has variable schedule delay,
it causes big error when calculating sample delay. Read the actual
HW pointer and feedback can improve the accuracy.
3. Do some minor code clean.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The commit [39f802d6b6d9: 'regulator: Build sysfs entries with static
attribute groups'] converted the sysfs entry creation to static
attribute groups, but this resulted in a regression due to the NULL
check of rdev->constraints. At the point where the device is
registered, rdev->constraints isn't set, so the attributes depending
on it are missing.
We may fix it by shuffling the code order in regulator_register(), but
a quicker fix is to just remove this NULL check. rdev->constraints is
in anyway always set to non-NULL in set_machine_constraints(), thus
the check there is basically superfluous.
Fixes: 39f802d6b6d9 ('regulator: Build sysfs entries with static attribute groups')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reportded-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since turning on idle-halt in commit fe46aa679f12 (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
really do
atmel,idle-halt property should be used with care, it actually makes the
watchdog not counting when the CPU is in idle state, therefore the
watchdog reset time depends on mean CPU usage and will not reset at all
of the CPU stop working while it is in idle state, which is probably not
what you want.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
With patch "include guest facilities in kvm facility test" it is no
longer necessary to have special handling for the non-LPAR case.
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Most facility related decisions in KVM have to take into account:
- the facilities offered by the underlying run container (LPAR/VM)
- the facilities supported by the KVM code itself
- the facilities requested by a guest VM
This patch adds the KVM driver requested facilities to the test routine.
It additionally renames struct s390_model_fac to kvm_s390_fac and its field
names to be more meaningful.
The semantics of the facilities stored in the KVM architecture structure
is changed. The address arch.model.fac->list now points to the guest
facility list and arch.model.fac->mask points to the KVM facility mask.
This patch fixes the behaviour of KVM for some facilities for guests
that ignore the guest visible facility bits, e.g. guests could use
transactional memory intructions on hosts supporting them even if the
chosen cpu model would not offer them.
The userspace interface is not affected by this change.
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
The facility lists were not fully copied.
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
There is now only one defconfig for the at91rm9200 and at91sam9. Add ethernet
support for the at91rm9200.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Recent distributions and userspace tools after 2009/2010 depend on
the existence of /sys/class/block/, and will not work with this option enabled.
Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Corrected pins used by usart3.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Under z/VM PQAP might trigger an operation exception if no crypto cards
are defined via APVIRTUAL or APDEDICATED.
[ 386.098666] Kernel BUG at 0000000000135c56 [verbose debug info unavailable]
[ 386.098693] illegal operation: 0001 ilc:2 [#1] SMP
[...]
[ 386.098751] Krnl PSW : 0704c00180000000 0000000000135c56 (kvm_s390_apxa_installed+0x46/0x98)
[...]
[ 386.098804] [<000000000013627c>] kvm_arch_init_vm+0x29c/0x358
[ 386.098806] [<000000000012d008>] kvm_dev_ioctl+0xc0/0x460
[ 386.098809] [<00000000002c639a>] do_vfs_ioctl+0x332/0x508
[ 386.098811] [<00000000002c660e>] SyS_ioctl+0x9e/0xb0
[ 386.098814] [<000000000070476a>] system_call+0xd6/0x258
[ 386.098815] [<000003fffc7400a2>] 0x3fffc7400a2
Lets add an extable entry and provide a zeroed config in that case.
Reported-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Tested-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
|
|
Bjørn reported that his machine hang during hibernation and eventually
bisected the problem to the following commit:
commit da2bc1b9db3351addd293e5b82757efe1f77ed1d
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Oct 23 19:23:26 2014 +0300
drm/i915: add poweroff_late handler
The problem seems to be that after the kernel puts the device into D3
the BIOS still tries to access it, or otherwise assumes that it's in D0.
This is clearly bogus, since ACPI mandates that devices are put into D3
by the OSPM if they are not wake-up sources. In the future we want to
unify more of the driver's runtime and system suspend paths, for example
by skipping all the system suspend/hibernation hooks if the device is
runtime suspended already. Accordingly for all other platforms the goal
is still to properly power down the device during hibernation.
v2:
- Another GEN4 Lenovo laptop had the same issue, while platforms from
other vendors (including mobile and desktop, GEN4 and non-GEN4) seem
to work fine. Based on this apply the workaround on all GEN4 Lenovo
platforms.
- add code comment about failing platforms (Ville)
Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-February/060633.html
Reported-and-bisected-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When we takeover from the BIOS and install our interrupt handler, the
BIOS may have left us a few surprises in the form of spontaneous
interrupts. (This is especially likely on hardware like 965gm where
display fifo underruns are continuous and the GMCH cannot filter that
interrupt souce.) As we enable our IRQ early so that we can use it
during hardware probing, our interrupt handler must be prepared to
handle a few sources prior to being fully configured. As such, we need
to add a simple is-ready check prior to dereferencing our KMS state for
reporting underruns.
Reported-by: Rob Clark <rclark@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1193972
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[Jani: dropped the extra !]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If the call to exchange-id returns with the EXCHGID4_FLAG_CONFIRMED_R flag
set, then that means our lease was established by a previous mount instance.
Ensure that we detect this situation, and that we clear the state held by
that mount.
Reported-by: Jorge Mora <Jorge.Mora@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
After d905c5df9aef ("PPC: POWERNV: move iommu_add_device earlier"), the
refcnt on the kobject backing the IOMMU group for a PCI device is
elevated by each call to pci_dma_dev_setup_pSeriesLP() (via
set_iommu_table_base_and_group). When we go to dlpar a multi-function
PCI device out:
iommu_reconfig_notifier ->
iommu_free_table ->
iommu_group_put
BUG_ON(tbl->it_group)
We trip this BUG_ON, because there are still references on the table, so
it is not freed. Fix this by moving the powernv bus notifier to common
code and calling it for both powernv and pseries.
Fixes: d905c5df9aef ("PPC: POWERNV: move iommu_add_device earlier")
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Anton has a busy ppc64le KVM box where guests sometimes hit the infamous
"kernel BUG at kernel/smpboot.c:134!" issue during boot:
BUG_ON(td->cpu != smp_processor_id());
Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops
output confirms it:
CPU: 0
Comm: watchdog/130
The problem is that we aren't ensuring the CPU active bit is set for the
secondary before allowing the master to continue on. The master unparks
the secondary CPU's kthreads and the scheduler looks for a CPU to run
on. It calls select_task_rq() and realises the suggested CPU is not in
the cpus_allowed mask. It then ends up in select_fallback_rq(), and
since the active bit isnt't set we choose some other CPU to run on.
This seems to have been introduced by 6acbfb96976f "sched: Fix hotplug
vs. set_cpus_allowed_ptr()", which changed from setting active before
online to setting active after online. However that was in turn fixing a
bug where other code assumed an active CPU was also online, so we can't
just revert that fix.
The simplest fix is just to spin waiting for both active & online to be
set. We already have a barrier prior to set_cpu_online() (which also
sets active), to ensure all other setup is completed before online &
active are set.
Fixes: 6acbfb96976f ("sched: Fix hotplug vs. set_cpus_allowed_ptr()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We do not want to allow a race with another NFS mount to cause
nfs41_walk_client_list() to establish a lease on our nfs_client before
we're done checking for trunking.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Pull nfsd fixes from Bruce Fields:
"Three miscellaneous bugfixes, most importantly the clp->cl_revoked
bug, which we've seen several reports of people hitting"
* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
sunrpc: integer underflow in rsc_parse()
nfsd: fix clp->cl_revoked list deletion causing softlock in nfsd
svcrpc: fix memory leak in gssp_accept_sec_context_upcall
|
|
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
|
|
Need to double the viewport height.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Passing zeroed drm_radeon_cs struct to DRM_IOCTL_RADEON_CS produces the
following oops.
Fix by always calling INIT_LIST_HEAD() to avoid the crash in list_sort().
----------------------------------
#include <stdint.h>
#include <fcntl.h>
#include <unistd.h>
#include <sys/ioctl.h>
#include <drm/radeon_drm.h>
static const struct drm_radeon_cs cs;
int main(int argc, char **argv)
{
return ioctl(open(argv[1], O_RDWR), DRM_IOCTL_RADEON_CS, &cs);
}
----------------------------------
[ttrantal@test2 ~]$ ./main /dev/dri/card0
[ 46.904650] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 46.905022] IP: [<ffffffff814d6df2>] list_sort+0x42/0x240
[ 46.905022] PGD 68f29067 PUD 688b5067 PMD 0
[ 46.905022] Oops: 0002 [#1] SMP
[ 46.905022] CPU: 0 PID: 2413 Comm: main Not tainted 4.0.0-rc1+ #58
[ 46.905022] Hardware name: Hewlett-Packard HP Compaq dc5750 Small Form Factor/0A64h, BIOS 786E3 v02.10 01/25/2007
[ 46.905022] task: ffff880058e2bcc0 ti: ffff880058e64000 task.ti: ffff880058e64000
[ 46.905022] RIP: 0010:[<ffffffff814d6df2>] [<ffffffff814d6df2>] list_sort+0x42/0x240
[ 46.905022] RSP: 0018:ffff880058e67998 EFLAGS: 00010246
[ 46.905022] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 46.905022] RDX: ffffffff81644410 RSI: ffff880058e67b40 RDI: ffff880058e67a58
[ 46.905022] RBP: ffff880058e67a88 R08: 0000000000000000 R09: 0000000000000000
[ 46.905022] R10: ffff880058e2bcc0 R11: ffffffff828e6ca0 R12: ffffffff81644410
[ 46.905022] R13: ffff8800694b8018 R14: 0000000000000000 R15: ffff880058e679b0
[ 46.905022] FS: 00007fdc65a65700(0000) GS:ffff88006d600000(0000) knlGS:0000000000000000
[ 46.905022] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 46.905022] CR2: 0000000000000000 CR3: 0000000058dd9000 CR4: 00000000000006f0
[ 46.905022] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 46.905022] DR3: 0000000000000000 DR6: 00000000ffff4ff0 DR7: 0000000000000400
[ 46.905022] Stack:
[ 46.905022] ffff880058e67b40 ffff880058e2bcc0 ffff880058e67a78 0000000000000000
[ 46.905022] 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 46.905022] 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 46.905022] Call Trace:
[ 46.905022] [<ffffffff81644a65>] radeon_cs_parser_fini+0x195/0x220
[ 46.905022] [<ffffffff81645069>] radeon_cs_ioctl+0xa9/0x960
[ 46.905022] [<ffffffff815e1f7c>] drm_ioctl+0x19c/0x640
[ 46.905022] [<ffffffff810f8fdd>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[ 46.905022] [<ffffffff810f90ad>] ? trace_hardirqs_on+0xd/0x10
[ 46.905022] [<ffffffff8160c066>] radeon_drm_ioctl+0x46/0x80
[ 46.905022] [<ffffffff81211868>] do_vfs_ioctl+0x318/0x570
[ 46.905022] [<ffffffff81462ef6>] ? selinux_file_ioctl+0x56/0x110
[ 46.905022] [<ffffffff81211b41>] SyS_ioctl+0x81/0xa0
[ 46.905022] [<ffffffff81dc6312>] system_call_fastpath+0x12/0x17
[ 46.905022] Code: 48 89 b5 10 ff ff ff 0f 84 03 01 00 00 4c 8d bd 28 ff ff
ff 31 c0 48 89 fb b9 15 00 00 00 49 89 d4 4c 89 ff f3 48 ab 48 8b 46 08 <48> c7
00 00 00 00 00 48 8b 0e 48 85 c9 0f 84 7d 00 00 00 c7 85
[ 46.905022] RIP [<ffffffff814d6df2>] list_sort+0x42/0x240
[ 46.905022] RSP <ffff880058e67998>
[ 46.905022] CR2: 0000000000000000
[ 47.149253] ---[ end trace 09576b4e8b2c20b8 ]---
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Split DCE6 and DCE8 programming of DCCG_AUDIO_DTO1
registers to properly enable DP audio for both DCE
revisions.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use proper tabs.
Signed-off-by: Slava Grigorev <slava.grigorev@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Move it out of the UNIPHY case to handle older DCE blocks.
- set audio dpms before video dpms
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If DCPLL or ext PLL is used, use the disp clk. If
PPLL is used, use the dp clock.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We don't necessarily have an EDID at this point when
audio detect gets called. Ideally we'd update these
fields in detect, but that requires a larger rework
of the display detect code.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Should be done only at detect time to avoid spurious
state changes on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
To avoid possible sound artifacts while setting up audio.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We need the pin from detect on, it's too late in dpms.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Don't touch the audio enable bits as these are already
handled in display detection. Enable the hdmi secondary
streams in hdmi enable to match dp. Rename dp dpms
callback to be consistent with hdmi.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=89327
https://bugzilla.kernel.org/show_bug.cgi?id=93921
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set actions consist of a regular OVS_KEY_ATTR_* attribute nested inside
of a OVS_ACTION_ATTR_SET action attribute. When converting masked actions
back to regular set actions, the inner attribute length was not changed,
ie, double the length being serialized. This patch fixes the bug.
Fixes: 83d2b9b ("net: openvswitch: Support masked set actions.")
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6ce29b0e2a04 ("gianfar: Avoid unnecessary reg accesses in adjust_link()")
eliminates unnecessary calls to adjust_link for phy devices which don't support
interrupts and need polling. As part of that work, the 'new_state' local flag,
which was used to reduce logging noise on the console, was eliminated.
Unfortunately, that means that a 'Link is Down' log message will now be
issued continuously if a link is configured as UP, the link state is down,
and the associated phy requires polling. This occurs because priv->oldduplex
is -1 in this case, which always differs from phydev->duplex. In addition,
phydev->speed may also differ from priv->oldspeed. gfar_update_link_state()
is therefore called each time a phy is polled, even if the link state did not
change.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
On some platforms, there are multiple SRAM nodes defined in the device tree but
some of them are disabled, leading to allocation failure. Try to find the first
enabled SRAM node and allocate from it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
at91rm9200 standby and suspend to ram has been broken since
00482a4078f4. It is wrongly using AT91_BASE_SYS which is a physical address
and actually doesn't correspond to any register on at91rm9200.
Use the correct at91_ramc_base[0] instead.
Fixes: 00482a4078f4 (ARM: at91: implement the standby function for pm/cpuidle)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
make build fail if structure no longer fits into ->cb storage.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfs_vm_page_mkwrite() should wait until the page cache invalidation
is finished. This is the second patch in a 2 patch series to deprecate
the NFS client's reliance on nfs_release_page() in the context of
nfs_invalidate_mapping().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
The DDRSDR controller fails miserably to put LPDDR1 memories in
self-refresh. Force the controller to think it has DDR2 memories
during the self-refresh period, as the DDR2 self-refresh spec is
equivalent to LPDDR1, and is correctly implemented in the
controller.
Assume that the second controller has the same fault, but that is
untested.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Removed timeout on XTAL, PLL lock and Master Clock Ready, hang if
something went wrong instead of continuing in unknown condition. There
is not much we can do if a PLL lock never ends, we are running in SRAM
and we will not be able to connect back the sdram or ddram in order to
be able to fire up a message or just panic.
As a bonus, not decounting the timeout register in slow clock mode
reduce cumulated suspend time and resume time from ~17ms to ~15ms.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Wenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
When invalidating the page cache for a regular file, we want to first
sync all dirty data to disk and then call invalidate_inode_pages2().
The latter relies on nfs_launder_page() and nfs_release_page() to deal
respectively with dirty pages, and unstable written pages.
When commit 9590544694bec ("NFS: avoid deadlocks with loop-back mounted
NFS filesystems.") changed the behaviour of nfs_release_page(), then it
made it possible for invalidate_inode_pages2() to fail with an EBUSY.
Unfortunately, that error is then propagated back to read().
Let's therefore work around the problem for now by protecting the call
to sync the data and invalidate_inode_pages2() so that they are atomic
w.r.t. the addition of new writes.
Later on, we can revisit whether or not we still need nfs_launder_page()
and nfs_release_page().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
