| Age | Commit message (Collapse) | Author |
|---|
|
On secondary CPUs, the Timer Control Register is not reset
to a sane value before the timer is registered, and the TRM
doesn't seem to indicate any reset value either. In some cases,
the kernel will take an interrupt too early, depending on what
junk was present in the registers at reset time.
The fix is to set the Timer Control Register to 0 before
registering the clock_event_device and enabling the interrupt.
Problem seen on VE (Cortex A5) and Tegra.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
On v7, we use the same cache maintenance instructions for data lines
as for unified lines. This was not the case for v6, where HARVARD_CACHE
was defined to indicate the L1 cache topology.
This patch removes the erroneous compile-time check for HARVARD_CACHE in
proc-v7.S, ensuring that we perform I-side invalidation at boot.
Reported-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Catalin Marinas <Catalin.Marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The merging of commits 1b6ba46b ("ARM: LPAE: MMU setup for the 3-level
page table format") and b4244738 ("ARM: 7202/1: Add Cortex-A7 proc info")
during the merge window ended up putting the Cortex-A7 proc_info into a
code block guarded by !CONFIG_ARM_LPAE. This makes Cortex-A7 platforms
unbootable when LPAE is enabled.
This patch moves the proc_info structure for Cortex-A7 outside of the
guarded block.
Cc: Pawel Moll <pawel.moll@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It turns out that the logical CPU mapping is useful even when !CONFIG_SMP
for manipulation of devices like interrupt and power controllers when
running a UP kernel on a CPU other than 0. This can happen when kexecing
a UP image from an SMP kernel.
In the future, multi-cluster systems running AMP configurations will
require something similar for mapping cluster IDs, so it makes sense to
decouple this logic in preparation for this support.
Acked-by: Yang Bai <hamo.by@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
To ensure correct alignment of cacheline-aligned data, the maximum
cacheline size needs to be known at compile time.
Since Cortex-A8 and Cortex-A15 have 64-byte cachelines (and it is likely
that there will be future ARMv7 implementations with the same line size)
then it makes sense to assume that CPU_V7 implies a 64-byte L1 cacheline
size. For CPUs with smaller caches, this will result in some harmless
padding but will help with single zImage work and avoid hitting subtle
bugs with misaligned data structures.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The exception fixup table is currently aligned to a 32-byte boundary.
Whilst this won't cause any problems, the exception_table_entry
structures contain only a pair of unsigned longs, so 4-byte alignment
is all that is required. If the table was walked from start to end,
cacheline alignment may bring some performance benefits, but since a
binary search is used, the access pattern is random and will not benefit
from a stricter alignment.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The linker script assumes a cacheline size of 32 bytes when aligning
the .data..cacheline_aligned and .data..percpu sections.
This patch updates the script to use L1_CACHE_BYTES, which should be set
to 64 on platforms that require it.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It doesn't seem right for the thermal subsystem to export a symbol
named generate_netlink_event. This function is thermal-specific and
its name should reflect that fact. Rename it to
thermal_generate_netlink_event.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: R.Durgadoss <durgadoss.r@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Allow ETHTOOL_GSSET_INFO ethtool ioctl() for unprivileged users.
ETHTOOL_GSTRINGS is already allowed, but is unusable without this one.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that all users of 'struct sysdev' are removed from the kernel, we
can safely remove the .h and .c files for this code, to ensure that no
one accidentally starts to use it again.
Many thanks for Kay who did all the hard work here on making this
happen.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If the ucb1x00 touchscreen is resumed while the touchscreen is being
touched, the main thread stops responding. This occurs because two
things happen:
1. When we suspended, we were woken up, and executed the loop.
Finding that the touchscreen was not pressed, we prepare to
schedule for a maximum timeout, before being stopped in
try_to_freeze().
2. an irq occurs, we disable the irq, and mark it as disabled,
and wake the thread. This wake occurs while the thread is
still within __refrigerator()
3. The thread is unfrozen, and __refrigerator() sets the threads
state back to INTERRUPTIBLE.
We then drop into schedule_timeout() with an infinite timeout and the
IRQ disabled. This prevents any further screen touches activating
the thread.
Fix this by using kthread_freezable_should_stop() which handles the
freezing issues for us outside of the hotspot where the task state
matters. Include a flag to ignore the touchscreen until it is
released to avoid sending unintended data to the application.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fixes:
net/bluetooth/hci_core.c: In function ‘__check_enable_hs’:
net/bluetooth/hci_core.c:2587:1: warning: return from incompatible pointer type [enabled by default]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a case in __sk_mem_schedule(), where an allocation
is beyond the maximum, but yet we are allowed to proceed.
It happens under the following condition:
sk->sk_wmem_queued + size >= sk->sk_sndbuf
The network code won't revert the allocation in this case,
meaning that at some point later it'll try to do it. Since
this is never communicated to the underlying res_counter
code, there is an inbalance in res_counter uncharge operation.
I see two ways of fixing this:
1) storing the information about those allocations somewhere
in memcg, and then deducting from that first, before
we start draining the res_counter,
2) providing a slightly different allocation function for
the res_counter, that matches the original behavior of
the network code more closely.
I decided to go for #2 here, believing it to be more elegant,
since #1 would require us to do basically that, but in a more
obscure way.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: Li Zefan <lizf@cn.fujitsu.com>
CC: Laurent Chavey <chavey@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the memcg sock code, we'll need to register allocations
that are temporarily over limit. Let's make sure that margin
is 0 in this case.
I am keeping this as a separate patch, so that if any weirdness
interaction appears in the future, we can now exactly what caused
it.
Suggested by Johannes Weiner
Signed-off-by: Glauber Costa <glommer@parallels.com>
CC: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
CC: Johannes Weiner <hannes@cmpxchg.org>
CC: Michal Hocko <mhocko@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is still a build bug with the sock memcg code, that triggers
with !CONFIG_NET, that survived my series of randconfig builds.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
CC: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix new kernel-doc warning:
Warning(include/net/sock.h:372): No description found for parameter 'sk_cgrp_prioidx'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix new kernel-doc warning:
Warning(drivers/net/phy/mdio_bus.c:49): No description found for parameter 'size'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
md5 key is added in socket through remote address.
remote address should be used in finding md5 key when
sending out reset packet.
Signed-off-by: shawnlu <shawn.lu@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently RSS rings are not created in a multi-channel config.
RSS rings can be created on one (out of four) interfaces per port in a
multi-channel config. Doing this insulates the driver from a FW bug wherin
multi-channel config is wrongly reported even when not enabled. This also
helps performance in a multi-channel config, as one interface per port gets
RSS rings.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every call to num_args() immediately checks the return value for
less than zero, as it will return -EFAULT for a failed get_user()
call. So it makes no sense for the function to be declared as an
unsigned long.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correctly implement a loss detection heuristic: New sequences (above
high_seq) sent during the fast recovery are deemed lost when higher
sequences are SACKed.
Current code does not catch these losses, because tcp_mark_head_lost()
does not check packets beyond high_seq. The fix is straight-forward by
checking packets until the highest sacked packet. In addition, all the
FLAG_DATA_LOST logic are in-effective and redundant and can be removed.
Update the loss heuristic comments. The algorithm above is documented
as heuristic B, but it is redundant too because heuristic A already
covers B.
Note that this change only marks some forward-retransmitted packets LOST.
It does NOT forbid TCP performing further CWR on new losses. A potential
follow-up patch under preparation is to perform another CWR on "new"
losses such as
1) sequence above high_seq is lost (by resetting high_seq to snd_nxt)
2) retransmission is lost.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver should check for mapping errors.
Machines with limited DMA maps may return an error when a PCI map is
requested (not an issue on standard x86).
Also use upper/lower 32 bits macros for clarity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skge device would assert carrier (link up) as soon as network device open
was called, rather than waiting until PHY has detected link.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With netem reordering, a gap of N is supposed to reorder every Nth packet with
given reorder probability. However, the code currently skips N packets and
reorders every (N+1)th packet.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Slave async events were mapped to single eq. This patch fixes this issue, so
the slaves can map the async events to any eq.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Num mtts from profile is really the number of mtt segments.
Thus, in make profile, to get the proper number of MTT entries,
must multiply num_mtts by mtts per segment.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Virtual Functions should not be aware their function number.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In native mode display all available staticstics.
In SRIOV mode on VF display only SW counters statistics,
in SRIOV mode on hypervisor display SW counters and errors (got from FW)
statistics.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In multifunction mode - DUMP_STATS command is not executed
for VFs.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug fix: Not all stats fields were cleared.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petriln <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should be allowing a 5ms delay after the charge pump is started in
order to ensure it has finished ramping.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
Passing the address of a variable as an operand to an asm statement
doesn't mark the value of this variable as used, so gcc may optimize its
initialisation away. Fix this by using the "m" constraint instead.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
|
|
Rename the "Mac ESP" irq as "ESP" to be consistent with all the other Mac
drivers and ESP drivers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Don't enable the SCSI irq when initialising the chip -- the irq has no
handler yet.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
macfb won't init in black & white modes since fb_alloc_cmap() no longer
works for zero cmap length. Fix this and also clean up a few printk's and
some stylistic inconsistencies.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The m68k core irq code stopped honoring these flags during the irq
restructuring in 2006.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
gpiolib drivers should first set the output data before setting the
direction to avoid putting glitches on an output signal. As an
additional bonus, we tweak the code to avoid unnecessary register
writes to the output and direction registers if they have no need
to be updated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We were not restoring the UCB1x00 gpio output data on resume, resulting
in incorrect GPIO output data after a resume. Add the missing register
write.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
mcp_priv() does unexpected things when passed a void pointer. Make it
a typed inline function, which ensures that it works correctly in
these cases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The perf_event_time() will call perf_cgroup_event_time()
if @event is a cgroup event. Just do it directly and avoid
the extra check..
Signed-off-by: Namhyung Kim <namhyung.kim@lge.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/1327021966-27688-2-git-send-email-namhyung.kim@lge.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When alloc_callchain_buffers() fails, it frees all of
entries before return. In addition, calling the
release_callchain_buffers() will cause a NULL pointer
dereference since callchain_cpu_entries is not set.
Signed-off-by: Namhyung Kim <namhyung.kim@lge.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/1327021966-27688-1-git-send-email-namhyung.kim@lge.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Sony Vaio VPCCW29FX does not resume correctly without
acpi_sleep=nonvs, so add it to the ACPI sleep blacklist.
https://bugzilla.kernel.org/show_bug.cgi?id=34722
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
With the conversion of atomicio's routines in place (see commits
6f68c91c55e and 700130b41f4), atomicio.[ch] can be removed, replacing
the APEI specific pre-mapping capabilities with the more generalized
versions that drivers/acpi/osl.c provides.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch adds support for RAM to ACPI's mapping capabilities in order
to support APEI error injection (EINJ) actions.
This patch re-factors similar functionality introduced in commit
76da3fb3575, bringing it into osl.c in preparation for removing
./drivers/acpi/atomicio.[ch].
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Base ACPI (CA) currently does not support atomic 64-bit reads and writes
(acpi_read() and acpi_write() split 64-bit loads/stores into two
32-bit transfers) yet APEI expects 64-bit transfer capability, even
when running on 32-bit systems.
This patch implements 64-bit read and write routines for APEI usage.
This patch re-factors similar functionality introduced in commit
04c25997c97, bringing it into the ACPI subsystem in preparation for
removing ./drivers/acpi/atomicio.[ch]. In the implementation I have
replicated acpi_os_read_memory() and acpi_os_write_memory(), creating
64-bit versions for APEI to utilize, as opposed to something more
elegant. My thinking is that we should attempt to see if we can get
ACPI's CA/OSL changed so that the existing acpi_read() and acpi_write()
interfaces are natively 64-bit capable and then subsequently remove the
replication.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch fixes CUBIC so that cwnd reductions made during RTOs can be
undone (just as they already can be undone when using the default/Reno
behavior).
When undoing cwnd reductions, BIC-derived congestion control modules
were restoring the cwnd from last_max_cwnd. There were two problems
with using last_max_cwnd to restore a cwnd during undo:
(a) last_max_cwnd was set to 0 on state transitions into TCP_CA_Loss
(by calling the module's reset() functions), so cwnd reductions from
RTOs could not be undone.
(b) when fast_covergence is enabled (which it is by default)
last_max_cwnd does not actually hold the value of snd_cwnd before the
loss; instead, it holds a scaled-down version of snd_cwnd.
This patch makes the following changes:
(1) upon undo, revert snd_cwnd to ca->loss_cwnd, which is already, as
the existing comment notes, the "congestion window at last loss"
(2) stop forgetting ca->loss_cwnd on TCP_CA_Loss events
(3) use ca->last_max_cwnd to check if we're in slow start
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Sangtae Ha <sangtae.ha@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes BIC so that cwnd reductions made during RTOs can be
undone (just as they already can be undone when using the default/Reno
behavior).
When undoing cwnd reductions, BIC-derived congestion control modules
were restoring the cwnd from last_max_cwnd. There were two problems
with using last_max_cwnd to restore a cwnd during undo:
(a) last_max_cwnd was set to 0 on state transitions into TCP_CA_Loss
(by calling the module's reset() functions), so cwnd reductions from
RTOs could not be undone.
(b) when fast_covergence is enabled (which it is by default)
last_max_cwnd does not actually hold the value of snd_cwnd before the
loss; instead, it holds a scaled-down version of snd_cwnd.
This patch makes the following changes:
(1) upon undo, revert snd_cwnd to ca->loss_cwnd, which is already, as
the existing comment notes, the "congestion window at last loss"
(2) stop forgetting ca->loss_cwnd on TCP_CA_Loss events
(3) use ca->last_max_cwnd to check if we're in slow start
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reverting back change that access enic->num_vfs outside
CONFIG_PCI_IOV
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a mx28evk board the following errors happens on mxs-sgtl5000 probe:
[ 0.660000] saif0_clk_set_rate: divider writing timeout
[ 0.670000] mxs-sgtl5000: probe of mxs-sgtl5000.0 failed with error -110
[ 0.670000] ALSA device list:
[ 0.680000] No soundcards found.
This timeout happens because clk_set_rate will result in writing to the DIV bits
of register HW_CLKCTRL_SAIF0 with the saif clock gated (CLKGATE bit set to one).
MX28 Reference states the following about CLKGATE:
"The DIV field can change ONLY when this clock gate bit field is low."
So call clk_prepare_enable prior to clk_set_rate to fix this problem.
After this change the mxs-saif driver can be correctly probed and audio is functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This reverts commit 42ff6572e5a4a7414330a4ca91f0335da67deca9.
New forcewake voodoo makes this no longer necessary.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
