| Age | Commit message (Collapse) | Author |
|---|
|
If an aggregate has the following conditions:
- The SRIOV LAG DDP package has been enabled
- The bond is in 802.3ad LACP mode
- The bond is disqualified from supporting SRIOV VF LAG
- Both interfaces were added simultaneously to the bond (same command)
Then there is a chance that the two interfaces will be assigned different
LACP Aggregator ID's. This will cause a failure of the LACP control over
the bond.
To fix this, we can detect if the primary interface for the bond (as
defined by the driver) is not in switchdev mode, and exit the setup flow
if so.
Reproduction steps:
%> ip link add bond0 type bond mode 802.3ad miimon 100
%> ip link set bond0 up
%> ifenslave bond0 eth0 eth1
%> cat /proc/net/bonding/bond0 | grep Agg
Check for Aggregator IDs that differ.
Fixes: ec5a6c5f79ed ("ice: process events created by lag netdev event handler")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_repr_add_mac() function indicates that it does not store the MAC
address filters in the firmware. However, it still increments vf->num_mac.
This is incorrect, as vf->num_mac should represent the number of MAC
filters currently programmed to firmware.
Indeed, we only perform this increment if the requested filter is a unicast
address that doesn't match the existing vf->hw_lan_addr. In addition,
ice_vc_repr_del_mac() does not decrement the vf->num_mac counter. This
results in the counter becoming out of sync with the actual count.
As it turns out, vf->num_mac is currently only used in legacy made without
port representors. The single place where the value is checked is for
enforcing a filter limit on untrusted VFs.
Upcoming patches to support VF Live Migration will use this value when
determining the size of the TLV for MAC address filters. Fix the
representor mode function to stop incrementing the counter incorrectly.
Fixes: ac19e03ef780 ("ice: allow process VF opcodes in different ways")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This series fixes an use-after-free read, and an out-of-bounds read in
the CAN Broadcast Manager (BCM) protocol found by Anderson Nascimento.
Link: https://patch.msgid.link/20250519125027.11900-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the procfs content is generated for a bcm_op which is in the process
to be removed the procfs output might show unreliable data (UAF).
As the removal of bcm_op's is already implemented with rcu handling this
patch adds the missing rcu_read_lock() and makes sure the list entries
are properly removed under rcu protection.
Fixes: f1b4e32aca08 ("can: bcm: use call_rcu() instead of costly synchronize_rcu()")
Reported-by: Anderson Nascimento <anderson@allelesecurity.com>
Suggested-by: Anderson Nascimento <anderson@allelesecurity.com>
Tested-by: Anderson Nascimento <anderson@allelesecurity.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20250519125027.11900-2-socketcan@hartkopp.net
Cc: stable@vger.kernel.org # >= 5.4
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN broadcast manager (CAN BCM) can send a sequence of CAN frames via
hrtimer. The content and also the length of the sequence can be changed
resp reduced at runtime where the 'currframe' counter is then set to zero.
Although this appeared to be a safe operation the updates of 'currframe'
can be triggered from user space and hrtimer context in bcm_can_tx().
Anderson Nascimento created a proof of concept that triggered a KASAN
slab-out-of-bounds read access which can be prevented with a spin_lock_bh.
At the rework of bcm_can_tx() the 'count' variable has been moved into
the protected section as this variable can be modified from both contexts
too.
Fixes: ffd980f976e7 ("[CAN]: Add broadcast manager (bcm) protocol")
Reported-by: Anderson Nascimento <anderson@allelesecurity.com>
Tested-by: Anderson Nascimento <anderson@allelesecurity.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20250519125027.11900-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Don't dirty the whole folio - fixes write amplification with
applications doing mmaped writes.
https://www.reddit.com/r/bcachefs/comments/1klzcg1/incredible_amounts_of_write_amplification_when/
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
Add a new struct for platform data for the ti,am62-sdhci compatible to
apply additional quirks, namely "SDHCI_QUIRK2_SUPPRESS_V1P8_ENA", to
host controllers with am62 compatible.
Note, the fix was originally introduced by commit 941a7abd4666
("mmc: sdhci_am654: Add sdhci_am654_start_signal_voltage_switch") but was
found to be applied too broadly and had to be reverted.
This fixes MMC init failures seen across am62x boards.
Fixes: ac5a41b472b4 ("Revert "mmc: sdhci_am654: Add sdhci_am654_start_signal_voltage_switch"")
Fixes: 941a7abd4666 ("mmc: sdhci_am654: Add sdhci_am654_start_signal_voltage_switch")
Cc: stable@vger.kernel.org
Suggested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20250516203121.3736379-1-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The "$id" value must match the relative path under bindings/ and is
missing the "net" sub-directory.
Fixes: 09328600c2f9 ("dt-bindings: can: convert microchip,mcp251x.txt to yaml")
Signed-off-by: "Rob Herring (Arm)" <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250507154201.1589542-1-robh@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
For SOCK_STREAM sockets, if user buffer size (len) is less
than skb size (skb->len), the remaining data from skb
will be lost after calling kfree_skb().
To fix this, move the statement for partial reading
above skb deletion.
Found by InfoTeCS on behalf of Linux Verification Center (linuxtesting.org)
Fixes: 30a584d944fb ("[LLX]: SOCK_DGRAM interface fixes")
Cc: stable@vger.kernel.org
Signed-off-by: Ilia Gavrilov <Ilia.Gavrilov@infotecs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When DP connected to a device with HDR capability,
the hdr structure was filled.Then connected to another
sink device without hdr capability, but the hdr info
still exist.
Fixes: e85959d6cbe0 ("drm: Parse HDR metadata info from EDID")
Cc: <stable@vger.kernel.org> # v5.3+
Signed-off-by: "feijuan.li" <feijuan.li@samsung.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250514063511.4151780-1-feijuan.li@samsung.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The tee info reg for teev2 is the same as teev1.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The bootloader info reg for pspv5 is the same as pspv4.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
'struct ahash_request' has a flexible array at the end, so it must be the
last member in a struct, to avoid overwriting other struct members.
Therefore, move 'fallback_req' to the end of the 'sun8i_ce_hash_reqctx'
struct.
Fixes: 56f6d5aee88d ("crypto: sun8i-ce - support hash algorithms")
Signed-off-by: Ovidiu Panait <ovidiu.panait.oss@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Current driver uses static LMTST region allocated by firmware.
Firmware allocated memory for LMTST is available in PF/VF BAR2.
Using this memory have performance impact as this is mapped as
device memory. There is another option to allocate contiguous
memory at run time and map this in LMT MAP table with the
help of AF driver. With this patch dynamic allocated memory
is used for LMTST.
Also add myself as maintainer for crypto octeontx2 driver
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Function otx2_cptlf_set_dev_info() initializes common
fields of cptlfs data-struct. This function is called
every time a cptlf is initialized but this needs be done
once for a cptlf block. So this initialization is moved
to early device probe code to avoid redundant initialization.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Only add ecb to the cipher name if it isn't already ecb.
Also use memcmp instead of strncmp since these strings are all
stored in an array of length CRYPTO_MAX_ALG_NAME.
Fixes: f1c131b45410 ("crypto: xts - Convert to skcipher")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Only add ecb to the cipher name if it isn't already ecb.
Also use memcmp instead of strncmp since these strings are all
stored in an array of length CRYPTO_MAX_ALG_NAME.
Fixes: 700cb3f5fe75 ("crypto: lrw - Convert to skcipher")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202505151503.d8a6cf10-lkp@intel.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Ensure that the hash state can be exported to and imported from
the generic algorithm.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
As shash is being phased out, use ahash for the generic tfm.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add ahash support to hmac so that drivers that can't do hmac in
hardware do not have to implement duplicate copies of hmac.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Soon hmac will support ahash. For compatibility hmac still supports
shash so it is possible for two hmac algorithms to be registered at
the same time. The shash algorithm will have the driver name
"hmac-shash(XXX-driver)". Due to a quirk in the API, there is no way
to locate the shash algorithm using the name "hmac(XXX-driver)". It
has to be addressed as either "hmac(XXX)" or "hmac-shash(XXX-driver)".
Looking it up with "hmac(XXX-driver)" will simply trigger the creation
of another instance, and on the second instantiation this will fail
with EEXIST.
Catch the error EEXIST along with ENOENT since it is expected.
If a real shash algorithm came this way, it would be addressed using
the proper name "hmac-shash(XXX-driver)".
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add support to crypto_inst_setname for having a driver template
name that differs from the algorithm template name.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Make reqsize static for shash algorithms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add export_import and import_core so that hmac can be used as a
fallback by block-only drivers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The shash desc needs to be zeroed after use in setkey as it is
not finalised (finalisation automatically zeroes it).
Also remove the final function as it's been superseded by finup.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Provide an option to handle the partial blocks in the ahash API.
Almost every hash algorithm has a block size and are only able
to hash partial blocks on finalisation.
As a first step disable virtual address support for algorithms
with state sizes larger than HASH_MAX_STATESIZE. This is OK as
virtual addresses are currently only used on synchronous fallbacks.
This means ahash_do_req_chain only needs to handle synchronous
fallbacks, removing the complexities of saving the request state.
Also move the saved request state into the ahash_request object
as nesting is no longer possible.
Add a scatterlist to ahash_request to store the partial block.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add export_core and import_core hooks. These are intended to be
used by algorithms which are wrappers around block-only algorithms,
but are not themselves block-only, e.g., hmac.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The core export and import functions are targeted at implementors
so move them into internal/hash.h.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Convert the Marvell CESA binding to DT schema format. The
marvell-cesa.txt and mv_cesa.txt are duplicate bindings.
The clock properties are quite varied for each platform hence the
if/then schemas. The old binding was fairly accurate with reality.
The original binding didn't mention there is 1 interrupt per CESA
engine. Based on users, there's a maximum of 2 engines.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Convert the Imagination Technologies hardware hash accelerator binding
to DT schema format. It's a straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Convert the HiSilicon HIP06/7 Security Accelerator binding to DT schema
format. It's a straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Convert the Broadcom SPUM/SPU2 binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Convert the Axis Crypto engine binding to DT schema format. It's a
straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Convert the AMD Cryptographic Coprocessor binding to DT schema format.
It's a straight forward conversion.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The mediatek,eip97-crypto binding is half abandoned. The driver was
dropped in 2020 as the Mediatek platforms use InsideSecure block and
the driver for it. All the platforms except MT7623 were updated. A
patch to update it was submitted, but never addressed the review
comments.
Link: https://lore.kernel.org/all/20210303080923.16761-1-vic.wu@mediatek.com/
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The fsl,sec-v6.0 binding is the same as the fsl,sec-v4.0 binding, so add
it to the existing schema and drop the old .txt binding.
The compatibles in the .txt binding don't match the 1 user. Follow the
user for the schema.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Enable the reporting of error counters through sysfs for QAT GEN6
devices and update the ABI documentation.
This enables the reporting of the following:
- errors_correctable - hardware correctable errors that allow the
system to recover without data loss.
- errors_nonfatal: errors that can be isolated to specific in-flight
requests.
- errors_fatal: errors that cannot be contained to a request,
requiring a Function Level Reset (FLR) upon occurrence.
Signed-off-by: Suman Kumar Chakraborty <suman.kumar.chakraborty@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Enable the reporting and handling of errors for QAT GEN6 devices.
Errors are categorized as correctable, non-fatal, or fatal. Error
handling involves reading the error source registers (ERRSOU0 to ERRSOU3)
to determine the source of the error and then decoding the actual source
reading specific registers.
The action taken depends on the error type:
- Correctable and Non-Fatal errors. These error are logged, cleared and
the corresponding counter is incremented.
- Fatal errors. These errors are logged, cleared and a Function Level
Reset (FLR) is scheduled.
This reports and handles the following errors:
- Accelerator engine (AE) correctable errors
- Accelerator engine (AE) uncorrectable errors
- Chassis push-pull (CPP) errors
- Host interface (HI) parity errors
- Internal memory parity errors
- Receive interface (RI) errors
- Transmit interface (TI) errors
- Interface for system-on-chip (SoC) fabric (IOSF) primary command
parity errors
- Shared RAM and slice module (SSM) errors
Signed-off-by: Suman Kumar Chakraborty <suman.kumar.chakraborty@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add a new CCP/PSP PCI device ID.
Signed-off-by: John Allen <john.allen@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If accept(2) is called on socket type algif_hash with
MSG_MORE flag set and crypto_ahash_import fails,
sk2 is freed. However, it is also freed in af_alg_release,
leading to slab-use-after-free error.
Fixes: fe869cdb89c9 ("crypto: algif_hash - User-space interface for hash operations")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
A recent patch that addressed a UAF introduced a reference count leak:
the parallel_data refcount is incremented unconditionally, regardless
of the return value of queue_work(). If the work item is already queued,
the incremented refcount is never decremented.
Fix this by checking the return value of queue_work() and decrementing
the refcount when necessary.
Resolves:
Unreferenced object 0xffff9d9f421e3d80 (size 192):
comm "cryptomgr_probe", pid 157, jiffies 4294694003
hex dump (first 32 bytes):
80 8b cf 41 9f 9d ff ff b8 97 e0 89 ff ff ff ff ...A............
d0 97 e0 89 ff ff ff ff 19 00 00 00 1f 88 23 00 ..............#.
backtrace (crc 838fb36):
__kmalloc_cache_noprof+0x284/0x320
padata_alloc_pd+0x20/0x1e0
padata_alloc_shell+0x3b/0xa0
0xffffffffc040a54d
cryptomgr_probe+0x43/0xc0
kthread+0xf6/0x1f0
ret_from_fork+0x2f/0x50
ret_from_fork_asm+0x1a/0x30
Fixes: dd7d37ccf6b1 ("padata: avoid UAF for reorder_work")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dominik Grzegorzek <dominik.grzegorzek@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This wasn't checking indirect extents.
Fixes: https://github.com/koverstreet/bcachefs/issues/887
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
There is a race condition in the readdir concurrency process, which may
access the rsp buffer after it has been released, triggering the
following KASAN warning.
==================================================================
BUG: KASAN: slab-use-after-free in cifs_fill_dirent+0xb03/0xb60 [cifs]
Read of size 4 at addr ffff8880099b819c by task a.out/342975
CPU: 2 UID: 0 PID: 342975 Comm: a.out Not tainted 6.15.0-rc6+ #240 PREEMPT(full)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x53/0x70
print_report+0xce/0x640
kasan_report+0xb8/0xf0
cifs_fill_dirent+0xb03/0xb60 [cifs]
cifs_readdir+0x12cb/0x3190 [cifs]
iterate_dir+0x1a1/0x520
__x64_sys_getdents+0x134/0x220
do_syscall_64+0x4b/0x110
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f996f64b9f9
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89
f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01
f0 ff ff 0d f7 c3 0c 00 f7 d8 64 89 8
RSP: 002b:00007f996f53de78 EFLAGS: 00000207 ORIG_RAX: 000000000000004e
RAX: ffffffffffffffda RBX: 00007f996f53ecdc RCX: 00007f996f64b9f9
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 00007f996f53dea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000207 R12: ffffffffffffff88
R13: 0000000000000000 R14: 00007ffc8cd9a500 R15: 00007f996f51e000
</TASK>
Allocated by task 408:
kasan_save_stack+0x20/0x40
kasan_save_track+0x14/0x30
__kasan_slab_alloc+0x6e/0x70
kmem_cache_alloc_noprof+0x117/0x3d0
mempool_alloc_noprof+0xf2/0x2c0
cifs_buf_get+0x36/0x80 [cifs]
allocate_buffers+0x1d2/0x330 [cifs]
cifs_demultiplex_thread+0x22b/0x2690 [cifs]
kthread+0x394/0x720
ret_from_fork+0x34/0x70
ret_from_fork_asm+0x1a/0x30
Freed by task 342979:
kasan_save_stack+0x20/0x40
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x37/0x50
kmem_cache_free+0x2b8/0x500
cifs_buf_release+0x3c/0x70 [cifs]
cifs_readdir+0x1c97/0x3190 [cifs]
iterate_dir+0x1a1/0x520
__x64_sys_getdents64+0x134/0x220
do_syscall_64+0x4b/0x110
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The buggy address belongs to the object at ffff8880099b8000
which belongs to the cache cifs_request of size 16588
The buggy address is located 412 bytes inside of
freed 16588-byte region [ffff8880099b8000, ffff8880099bc0cc)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x99b8
head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
anon flags: 0x80000000000040(head|node=0|zone=1)
page_type: f5(slab)
raw: 0080000000000040 ffff888001e03400 0000000000000000 dead000000000001
raw: 0000000000000000 0000000000010001 00000000f5000000 0000000000000000
head: 0080000000000040 ffff888001e03400 0000000000000000 dead000000000001
head: 0000000000000000 0000000000010001 00000000f5000000 0000000000000000
head: 0080000000000003 ffffea0000266e01 00000000ffffffff 00000000ffffffff
head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000008
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880099b8080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880099b8100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8880099b8180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8880099b8200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880099b8280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
POC is available in the link [1].
The problem triggering process is as follows:
Process 1 Process 2
-----------------------------------------------------------------
cifs_readdir
/* file->private_data == NULL */
initiate_cifs_search
cifsFile = kzalloc(sizeof(struct cifsFileInfo), GFP_KERNEL);
smb2_query_dir_first ->query_dir_first()
SMB2_query_directory
SMB2_query_directory_init
cifs_send_recv
smb2_parse_query_directory
srch_inf->ntwrk_buf_start = (char *)rsp;
srch_inf->srch_entries_start = (char *)rsp + ...
srch_inf->last_entry = (char *)rsp + ...
srch_inf->smallBuf = true;
find_cifs_entry
/* if (cfile->srch_inf.ntwrk_buf_start) */
cifs_small_buf_release(cfile->srch_inf // free
cifs_readdir ->iterate_shared()
/* file->private_data != NULL */
find_cifs_entry
/* in while (...) loop */
smb2_query_dir_next ->query_dir_next()
SMB2_query_directory
SMB2_query_directory_init
cifs_send_recv
compound_send_recv
smb_send_rqst
__smb_send_rqst
rc = -ERESTARTSYS;
/* if (fatal_signal_pending()) */
goto out;
return rc
/* if (cfile->srch_inf.last_entry) */
cifs_save_resume_key()
cifs_fill_dirent // UAF
/* if (rc) */
return -ENOENT;
Fix this by ensuring the return code is checked before using pointers
from the srch_inf.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220131 [1]
Fixes: a364bc0b37f1 ("[CIFS] fix saving of resume key before CIFSFindNext")
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Wang Zhaolong <wangzhaolong1@huawei.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
|
|
The following commit:
efef7f184f2e ("x86/msr: Add explicit includes of <asm/msr.h>")
added a superfluous inclusion of <asm/asm.h> to
drivers/acpi/processor_throttling.c.
Remove it.
Fixes: efef7f184f2e ("x86/msr: Add explicit includes of <asm/msr.h>")
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Link: https://lore.kernel.org/r/20250512084552.1586883-2-xin@zytor.com
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clk driver fixes from Chen-Yu Tsai:
Only two changes:
- Fix the order of arguments in clk macro for
SUNXI_CCU_MP_DATA_WITH_MUX_GATE_FEAT that was recently introduced in
v6.15-rc1
- Add missing post-divider for D1 MMC clocks to correct halved
performance
* tag 'sunxi-clk-fixes-for-6.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: d1: Add missing divider for MMC mod clocks
clk: sunxi-ng: fix order of arguments in clock macro
|
|
Add two helpers, one for posting overflows for lockless_cq rings, and
one for non-lockless_cq rings. The former can allocate sanely with
GFP_KERNEL, but needs to grab the completion lock for posting, while the
latter must do non-sleeping allocs as it already holds the completion
lock.
While at it, mark the overflow handling functions as __cold as well, as
they should not generally be called during normal operations of the
ring.
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Rather than pass extra1/extra2 separately, just pass in the (now) named
io_big_cqe struct instead. The callers that don't use/support CQE32 will
now just pass a single NULL, rather than two seperate mystery zero
values.
Move the clearing of the big_cqe elements into io_alloc_ocqe() as well,
so it can get moved out of the generic code.
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The number of arguments to io_alloc_ocqe() is a bit unwieldy. Make it
take a struct io_cqe pointer rather than three separate CQE args. One
path already has that readily available, add an io_init_cqe() helper for
the remaining two.
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a new helper, io_alloc_ocqe(), that simply allocates and fills an
overflow entry. Then it can get done outside of the locking section,
and hence use more appropriate gfp_t allocation flags rather than always
default to GFP_ATOMIC.
Inspired by a previous series from Pavel:
https://lore.kernel.org/io-uring/cover.1747209332.git.asml.silence@gmail.com/
Reviewed-by: Caleb Sander Mateos <csander@purestorage.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
