| Age | Commit message (Collapse) | Author |
|---|
|
The IVA DPLL in DRA7xx provides the output clocks for only the IVAHD
subsystem in DRA7xx as compared to previous OMAP generations when it
provided the clocks for both DSP and IVAHD subsystems. This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
IVA DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The reset value of the divider M2 (that supplies the IVA_GFLCK, the
functional clock for the IVAHD subsystem) does not match a specific
OPP. So, the derived output clock from this IVA DPLL has to be
initialized as well to avoid initializing these divider outputs to an
incorrect frequencies.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 2300 MHz, so
the dpll_iva_ck clock rate used is half of this value. The value for the
divider clock, dpll_iva_m2_ck, has to be set to 388.333334 MHz or more
for the divider clk logic to compute the appropriate divider value for
OPP_NOM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The DSP DPLL is a new DPLL compared to previous OMAP generations and
supplies the root clocks for the DSP processors, as well as a mux
input source for EVE sub-system (on applicable SoCs). This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
DSP DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The DSP DPLL provides two output clocks, DSP_GFCLK and EVE_GCLK. The
desired rate for DSP_GFCLK is 600 MHz (same as DSP DPLL CLKOUT frequency),
and is currently auto set due to the desired M2 divider value being the
same as reset value for the locked frequency of 600 MHz. The EVE_GCLK
however is required to be 400 MHz, so set the dpll_dsp_m3x2_ck's rate
explicitly so that the divider is set properly. The dpll_dsp_m2_ck rate
is also set explicitly to not rely on any implicit matching divider reset
values to the locked DPLL frequency.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 1200 MHz, so
the dpll_dsp_ck clock rate used is half of this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IPU1 functional clock is actually the output of a mux clock,
ipu1_gfclk_mux. The mux clock is sourced by default from the
DPLL_ABE_X2_CLK, and this results in a rather odd clock frequency
(361 MHz) for the IPU1 functional clock on platforms where ABE_DPLL
is configured properly. Reconfigure the mux clock to be sourced from
CORE_IPU_ISS_BOOST_CLK (dpll_core_h22x2_ck), so that both the IPU1
and IPU2 are running from the same clock and clocked at the same
nominal frequency of 425 MHz.
This also ensures that IPU1 functional clock is always configured
properly and becomes independent of the state of the ABE DPLL on
all boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers H11 & H12 (functional clocks for DSP
and IVAHD respectively) are identical to each other, but are different
at each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP_NOM values as defined in
the OMAP5432 SR2.0 Data Manual Book vK, section 5.2.3.5 "DPLL_IVA
Preferred Settings". The recommended maximum DPLL locked frequency is
2330 MHz for OPP_NOM (value for DPLL_IVA_X2_CLK), so the dpll_iva_ck
clock rate used is half of this value. The value 465.92 MHz is used
instead of 465.9 MHz for dpll_iva_h11x2_ck so that proper divider
value can be calculated.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers M4 & M5 (functional clocks for DSP and
IVAHD respectively) are identical to each other, but are different at
each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP100 values as defined in the
OMAP4430 ES2.x Public TRM vAP, section "3.6.3.8.7 DPLL_IVA Preferred
Settings". The DPLL locked frequency is 1862.4 MHz (value for
DPLL_IVA_X2_CLK), so the dpll_iva_ck clock rate used is half of
this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Renesas Salvator-XS (Salvator-X 2nd version) development board can
be equipped with either an R-Car H3 ES2.0 or M3-W ES1.x SiP, which are
pin-compatible.
Document board part number and compatible values for the version with
R-Car H3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The board part numbers for the R-Car H3 and M3 ULCB boards corresponded
to versions predating mass production. Update them for mass production.
Note that the H3 ULCB board can be equipped with either revision ES1.1
or ES2.0 of the R-Car H3 SoC. While these have different board part
numbers, no new compatible values are needed, as the revision can be
detected at runtime using the PRR register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Document the iW-RainboW-G20D-Qseven-RZG1M device tree bindings,
listing it as a supported board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Document the iW-RainboW-G20M-Qseven-RZG1M device tree bindings,
listing it as a supported system on module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The bogus 'device_type = "pci"' confuses dtc, causing lots of totally
unrelated warnings. After fixing that, real warnings like
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (pci_device_reg): Node /pci@ee090000/usb@0,1 PCI unit address format error, expected "1,0"
are left. Correct the unit-addresses and reg properties of the subnodes
to fix these.
Signed-off-by: Rob Herring <robh@kernel.org>
[geert: Improve description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for iWave RainboW-G20D-Qseven board based on RZ/G1M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for iWave RZG1M Qseven System On Module.
http://www.iwavesystems.com/rz-g1m-qseven-module.html
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Adds VIN, decoder and connector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add device tree source for Renesas GR-Peach board.
GR-Peach is an RZ/A1H based board with 10MB of on-chip SRAM and 8MB
QSPI flash storage.
Add support for the board, and create a 2MB partition to use as rootfs.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Export the ethernet gate clock to the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Export the USB related clocks (for the USB controller and the USB2 PHYs)
so they can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
This exports the clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Export the SDIO clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Export the clocks for the SAR ADC so they can be used in the
dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
|
|
Motorola Droid 4 uses a WL1285C, so use proper compatible value.
To avoid regressions while support for the new compatible value
is added to the Linux kernel, the old compatible value is preserved
as fallback.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Droid 4 has a isl29030 to measure ambient light (e.g. for
automatically adapting display brightness) and proximity.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Orange Pi Plus 2E, unlike the Orange Pi PC and PC Plus which its
schematics are based on, uses an external Realtek RTL8211E PHY in
RGMII mode, with a GPIO enabling the regulator for I/O signalling
power supplies. The PHY's main power supply is enabled by the main
5V power supply.
Add the regulator and PHY nodes, and override the PHY phandle under
the EMAC node, so that the EMAC works properly on this board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This removes the dummy clk81 gate and replaces it with the actual clock
controller's CLKID_CLK81. This will also allow us to pass the real clock
IDs to all devices where the clock is controlled by clkc in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add basic support for stm32h743i-discovery board
This board offers :
_ 2MBytes Flash
_ 1 x micro USB OTG port
_ 1 x STLink connector (micro USB)
_ 1 x micro SD card slot
_ 1 x RJ45 connector
_ 1 x RCA connector
_ 2 x Audio jack connectors (in and out)
_ 2 x speaker connectors (left and right)
_ 1 x joystick
_ 1 x DCMI connector (Digital camera interface)
_ 1 x 4 inch DSI LCD (Display Serial Interface)
_ Arduino Uno Connectors
_ 2 x PIO connectors (PMOD and PMOD+)
_ 1 x wakeup button
_ 1 x reset button
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This usart is used for console output on stm32h743i-disco board
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Add usart2 pins definition in order to add usart2 support
dedicated for console output on stm32h743i-disco board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
The A83T has 1 pingroup with 13 pins belonging to the R_PIO
or special pin controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The size field of the memory node is wrong. Rely on the default value in
sama5d2.dtsi that happens to be correct for the SAMA5D2 Xplained board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
sources
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Enable the CRC32 crypto on stm32429i-eval board.
Signed-off-by: Cosar Dindar <cosardindar@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Enable the CRC32 crypto on stm32429-disco board.
Signed-off-by: Cosar Dindar <cosardindar@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Add CRC32 Crypto support to stm32f429.
Signed-off-by: Cosar Dindar <cosardindar@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Enable OV2640 camera support of STM32F429-EVAL board.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Enable STMPE1600 gpio expander of STM32F429-EVAL board.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Enable DCMI camera interface on STM32F429-EVAL board.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Enable DCMI camera interface on STM32F429 MCU.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
rcc node must include reset-cells node.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch set each gpio controller as a interrupt controller. User who
wants to use gpio as interrupt will have choice to use either "gpiolib"
interface or "common" interrupt interface.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
This patch adds watchdog support for STM32x9I-Eval board.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Add watchdog into DT for stm32f429 family.
Signed-off-by: Yannick FERTRE <yannick.fertre@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Allwinner V3s SoC features a "Display Engine 2.0" with only one mixer
and only one TCON connected to this mixer, which have RGB LCD output.
Add device nodes for this display pipeline.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add SoC specific compatibles for all sunXi crypto nodes, in addition to
the one already used (allwinner,sun4i-a10-crypto).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add a node for the cryptographic engine that can be found on sun5i SoCs.
This cryptographic engine is compatible with the Allwinner cryptographic
accelerator driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Enable ltdc & enable am-480272h3tmqw-t01h panel.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Add LTDC (Lcd-tft Display Controller) support.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Stm32f769I & stm32f746 are MCUs of stm32f7 family. Here are the major
specs of the two boards:
stm32f769I discovery board:
- Cortex-M7 core @216MHz
- 2MB mcu internal flash
- 512KB internal sram
- 16MB sdram memory
- 64MB qspi flash memory
- 4 inch wvga LCD-TFT Display
stm32f746 discovery board:
- Cortex-M7 core @216MHz
- 1MB mcu internal flash
- 320KB internal sram
- 8MB sdram memory
- 16MB qspi flash memory
- 4.3 inch 480x272 LCD-TFT display
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
|
Add audio driver node for mt2701
Signed-off-by: Garlic Tseng <garlic.tseng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The imx6 PCI driver ignores the GPIO polarity from 'reset-gpio' and
considers that the PCI reset is active low, unless the
property 'reset-gpio-active-high' is present.
Fix the device tree description by explicitly passing the
'GPIO_ACTIVE_LOW' flag to the 'reset-gpio' property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
