| Age | Commit message (Collapse) | Author |
|---|
|
bnxt_add_one_ctr() adds a hardware counter to a software counter and
adjusts for the hardware counter wraparound against the mask. The logic
assumes that the hardware counter is always smaller than or equal to
the mask.
This assumption is mostly correct. But in some cases if the firmware
is older and does not provide the accurate mask, the driver can use
a mask that is smaller than the actual hardware mask. This can cause
some extra carry bits to be added to the software counter, resulting in
counters that far exceed the actual value. Fix it by masking the
hardware counter with the mask passed into bnxt_add_one_ctr().
Fixes: fea6b3335527 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware is unable to retain the port counters during any kind of
fatal or non-fatal resets, so we must clear the port counters to
avoid false detection of port counter overflow.
Fixes: fea6b3335527 ("bnxt_en: Accumulate all counters.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.
Fix the firmware call by passing page_number 0 for the A2h slave address
space.
Fixes: 42ee18fe4ca2 ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Transactions sit on one of several lists, depending on their state
(allocated, pending, complete, or polled). A spinlock protects
against concurrent access when transactions are moved between these
lists.
Transactions are also reference counted. A newly-allocated
transaction has an initial count of 1; a transaction is released in
gsi_trans_free() only if its decremented reference count reaches 0.
Releasing a transaction includes removing it from the polled (or if
unused, allocated) list, so the spinlock is acquired when we release
a transaction.
The reference count is used to allow a caller to synchronously wait
for a committed transaction to complete. In this case, the waiter
takes an extra reference to the transaction *before* committing it
(so it won't be freed), and releases its reference (calls
gsi_trans_free()) when it is done with it.
Similarly, gsi_channel_update() takes an extra reference to ensure a
transaction isn't released before the function is done operating on
it. Until the transaction is moved to the completed list (by this
function) it won't be freed, so this reference is taken "safely."
But in the quiesce path, we want to wait for the "last" transaction,
which we find in the completed or polled list. Transactions on
these lists can be freed at any time, so we (try to) prevent that
by taking the reference while holding the spinlock.
Currently gsi_trans_free() decrements a transaction's reference
count unconditionally, acquiring the lock to remove the transaction
from its list *only* when the count reaches 0. This does not
protect the quiesce path, which depends on the lock to ensure its
extra reference prevents release of the transaction.
Fix this by only dropping the last reference to a transaction
in gsi_trans_free() while holding the spinlock.
Fixes: 9dd441e4ed575 ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201114182017.28270-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If tcp socket has more data than Encrypted Handshake Message then
tls_sw_recvmsg will try to decrypt next record instead of returning
full control message to userspace as mentioned in comment. The next
message - usually Application Data - gets corrupted because it uses
zero copy for decryption that's why the data is not stored in skb
for next iteration. Revert check to not decrypt next record if
current is not Application Data.
Fixes: 692d7b5d1f91 ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/1605413760-21153-1-git-send-email-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During rmnet unregistration, the real device rx_handler is first cleared
followed by the removal of rx_handler_data after the rcu synchronization.
Any packets in the receive path may observe that the rx_handler is NULL.
However, there is no check when dereferencing this value to use the
rmnet_port information.
This fixes following splat by adding the NULL check.
Unable to handle kernel NULL pointer dereference at virtual
address 000000000000000d
pc : rmnet_rx_handler+0x124/0x284
lr : rmnet_rx_handler+0x124/0x284
rmnet_rx_handler+0x124/0x284
__netif_receive_skb_core+0x758/0xd74
__netif_receive_skb+0x50/0x17c
process_backlog+0x15c/0x1b8
napi_poll+0x88/0x284
net_rx_action+0xbc/0x23c
__do_softirq+0x20c/0x48c
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Link: https://lore.kernel.org/r/1605298325-3705-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Recycle the page running page_pool_put_full_page() in
mvneta_swbm_add_rx_fragment routine when the last descriptor
contains just the FCS or if the received packet contains more than
MAX_SKB_FRAGS fragments
Fixes: ca0e014609f0 ("net: mvneta: move skb build after descriptors processing")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/df6a2bad70323ee58d3901491ada31c1ca2a40b9.1605291228.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix an issue where dump stack is printed on suspend resume flow due to
netif_set_real_num_rx_queues() is not called with rtnl_lock held().
Fixes: 686cff3d7022 ("net: stmmac: Fix incorrect location to set real_num_rx|tx_queues")
Reported-by: Christophe ROULLIER <christophe.roullier@st.com>
Tested-by: Christophe ROULLIER <christophe.roullier@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201115074210.23605-1-vee.khee.wong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In br_forward.c and br_input.c fields dev->stats.tx_dropped and
dev->stats.multicast are populated, but they are ignored in
ndo_get_stats64.
Fixes: 28172739f0a2 ("net: fix 64 bit counters on 32 bit arches")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/58ea9963-77ad-a7cf-8dfd-fc95ab95f606@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 83a8471ba255 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605250173-18438-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 9efc9b2b04c7 ("net: stmmac: Add dwmac-intel-plat for GBE driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605249243-17262-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3ced0a88cd4c ("qlcnic: Add support to run firmware POST")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605248186-16013-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: ca139d76b0d9 ("cx82310_eth: re-enable ethernet mode after router reboot")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605247627-15385-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Around one third of the fixes this time are for dts files that list
their ethernet controller as using 'phy-mode="rgmii"' but are changed
to 'phy-mode="rgmii-id"' now, because the PHY drivers (realtek,
ksz9031, dp83867, ...) now configure the internal delay based on that
when they used to stay on the hardware default.
The long story is archived at
https://lore.kernel.org/netdev/CAMj1kXEEF_Un-4NTaD5iUN0NoZYaJQn-rPediX0S6oRiuVuW-A@mail.gmail.com/
I was trying to hold off on the bugfixes until there was a solution
that would avoid breaking all boards, but that does not seem to be
happening any time soon, so I am now sending the correct version of
the dts files to ensure that at least these machines can use their
network devices again.
The other changes this time are:
- Updating the MAINTAINER lists for Allwinner and Samsung SoCs
- Multiple i.MX8MN machines get updates for their CPU operating
points to match the data sheet
- A revert for a dts patch that caused a regression in USB support on
Odroid U3
- Two fixes for the AMD Tee driver, addressing a memory leak and
missing locking
- Mark the network subsystem on qoriq-fman3 as cache coherent for
correctness as better performance.
- Minor dts fixes elsewhere, addressing dtc warnings and similar
problems"
* tag 'arm-soc-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: dts: exynos: revert "add input clock to CMU in Exynos4412 Odroid"
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: stm32: Keep VDDA LDO1 always on on DHCOM
ARM: dts: stm32: Enable thermal sensor support on stm32mp15xx-dhcor
ARM: dts: stm32: Define VIO regulator supply on DHCOM
ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2
ARM: dts: stm32: Fix TA3-GPIO-C key on STM32MP1 DHCOM PDK2
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
tee: amdtee: synchronize access to shm list
tee: amdtee: fix memory leak due to reset of global shm list
arm64: dts: agilex/stratix10: Fix qspi node compatible
ARM: dts: imx6q-prti6q: fix PHY address
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
arm64: dts imx8mn: Remove non-existent USB OTG2
arm64: dts: imx8mm-beacon-som: Fix Choppy BT audio
arm64: dts: fsl: DPAA FMan DMA operations are coherent
arm64: dts: fsl: fix endianness issue of rcpm
arm64: dts: imx8mn-evk: fix missing PMIC's interrupt line pull-up
...
|
|
If intel context create failed, the perf_request_latency() will return 0
rather than error, because we doesn't initialize the return value.
Fixes: 25c26f18ea79 ("drm/i915/selftests: Measure dispatch latency")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116143540.3648870-1-zhangxiaoxu5@huawei.com
(cherry picked from commit 19384452052a1e0525e663bfbdd62ac1399bb647)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
If intel context create failed, the perf_series_engines() will return 0
rather than error, because we doesn't initialize the return value.
Fixes: cbfd3a0c5a55 ("drm/i915/selftests: Add request throughput measurement to perf")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116144112.3673011-1-zhangxiaoxu5@huawei.com
(cherry picked from commit 01d708840c26c9532579677eaca942363a009fd5)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
I forgot to free the old list when growing past 16 entries.
Luckily, as much as I checked, none of the current platforms has more than
16 workarounds on a single list.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 452420d22d5b ("drm/i915: Fuse per-context workaround handling with the common framework")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201113132510.2298483-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 77c296966e866a795742a46fc52a218771894867)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Some media power gates are disabled by default. commit 5d86923060fc
("drm/i915/tgl: Enable VD HCP/MFX sub-pipe power gating")
tried to enable it, but it duplicated an existent register.
So, the main PG setup sequences ended up overwriting it.
So, let's now merge this to the main PG setup sequence.
v2: (Chris): s/BIT/REG_BIT, remove useless comment,
remove useless =0, use the right gt,
remove rc6 sequence doubt from commit message.
Fixes: 5d86923060fc ("drm/i915/tgl: Enable VD HCP/MFX sub-pipe power gating")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: stable@vger.kernel.org#v5.5+
Cc: Dale B Stimson <dale.b.stimson@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201111072859.1186070-1-rodrigo.vivi@intel.com
(cherry picked from commit 695dc55b573985569259e18f8e6261a77924342b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V fix from Wei Liu:
"One patch from Chris to fix kexec on Hyper-V"
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: vmbus: Allow cleanup of VMBUS_CONNECT_CPU if disconnected
|
|
Pull vhost fixes from Michael Tsirkin:
"Fixes all over the place, most notably vhost scsi IO error fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost scsi: Add support for LUN resets.
vhost scsi: add lun parser helper
vhost scsi: fix cmd completion race
vhost scsi: alloc cmds per vq instead of session
vhost: add helper to check if a vq has been setup
vdpasim: fix "mac_pton" undefined error
swiotlb: using SIZE_MAX needs limits.h included
|
|
Update cxgb4 and cxgb3 driver maintainer
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20201116104322.3959-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This has been stable for a while.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A user reports (slightly shortened from the original message):
libphy: lantiq,xrx200-mdio: probed
mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing.
gswip 1e108000.switch lan: no phy at 2
gswip 1e108000.switch lan: failed to connect to port 2: -19
lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy
This is a single-port board using the internal Fast Ethernet PHY. The
user reports that switching to PHY scanning instead of configuring the
PHY within device-tree works around this issue.
The documentation for the standalone variant of the PHY11G (which is
probably very similar to what is used inside the xRX200 SoCs but having
the firmware burnt onto that standalone chip in the factory) states that
the PHY needs 300ms to be ready for MDIO communication after releasing
the reset.
Add a 300ms delay after initializing all GPHYs to ensure that the GPHY
firmware had enough time to initialize and to appear on the MDIO bus.
Unfortunately there is no (known) documentation on what the minimum time
to wait after releasing the reset on an internal PHY so play safe and
take the one for the external variant. Only wait after the last GPHY
firmware is loaded to not slow down the initialization too much (
xRX200 has two GPHYs but newer SoCs have at least three GPHYs).
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 65b4414a05eb ("selftests/bpf: add sockopt test that exercises BPF_F_ALLOW_MULTI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20201116101633.64627-1-wanghai38@huawei.com
|
|
We catch the case where we enter generic_file_buffered_read() with data
already transferred, but we also need to be careful not to allow an async
page lock if we're looping transferring data. If not, we could be
returning -EIOCBQUEUED instead of the transferred amount, and it could
result in double waitqueue additions as well.
Cc: stable@vger.kernel.org # v5.9
Fixes: 1a0a7853b901 ("mm: support async buffered reads in generic_file_buffered_read()")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
During stream start DSP firmware requires LPCS disabled as that moment in
time is resource heavy. Currently high-clock is selected on start of
second stream onwards while low-clock is re-selected before stream
actually leaves RESUME state i.e. PAUSE_STREAM call. Fix this by always
updating clock before RESUME_STREAM and directly after PAUSE_STREAM.
Fixes: a126750fc865 ("ASoC: Intel: catpt: PCM operations")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201116133332.8530-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Playing with very low period sizes may lead to timeouts when awaiting
RESET_STREAM reply for offload streams. This is caused by NOTIFY_POSITION
appearing in the middle of trigger(stop).
Stream is unprepared during trigger(stop) where PAUSE_STREAM IPC gets
invoked. However, all data that is already mixed in DSP firmware's mixer
stream will still be played regardless of the pause. For offload streams,
this means possibility for another NOTIFY_POSITION to process. Keep these
notifications in check by only handling them when stream is in prepared
state.
Fixes: a126750fc865 ("ASoC: Intel: catpt: PCM operations")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201116133332.8530-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix to return the error code from
devm_reset_control_get_optional_exclusive() instaed of 0
in cqspi_probe().
Fixes: 31fb632b5d43ca ("spi: Move cadence-quadspi driver to drivers/spi/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20201116141836.2970579-1-chengzhihao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
lpass_pcm_data is not freed in error paths. Free it in
error paths to avoid memory leak.
Fixes: 022d00ee0b55 ("ASoC: lpass-platform: Fix broken pcm data usage")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/1605416210-14530-1-git-send-email-srivasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
S24_LE is 24 bit audio in 32 bit container configuration
Fixing the configuration to match the data arrangement of
this audio format.
Fixes: c5477e966728 ("ASoC: Intel: Add KeemBay platform driver")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201116061905.32431-2-michael.wei.hong.sit@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If we have more than 4 displays we will run
into dummy irq calls or flip timout issues.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
From commit 6915564dc5a8 ("ACPI: OSL: Change the type of
acpi_os_map_generic_address() return value"),
acpi_os_map_generic_address() will return logical address or NULL
for error, but for ACPI_ADR_SPACE_SYSTEM_IO case, it should be also
return 0 as it's a normal case, but now it will return -ENXIO.
So check it out for such case to avoid einj module initialization
fail.
Fixes: 6915564dc5a8 ("ACPI: OSL: Change the type of acpi_os_map_generic_address() return value")
Cc: <stable@vger.kernel.org>
Reviewed-by: James Morse <james.morse@arm.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aili Yao <yaoaili@kingsoft.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Martin Schiller is an active developer and reviewer for the X.25 code.
His company is providing products based on the Linux X.25 stack.
So he is a good candidate for maintainers of the X.25 code.
The original maintainer of the X.25 network layer (Andrew Hendry) has
not sent any email to the netdev mail list since 2013. So he is probably
inactive now.
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20201114111029.326972-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Packets are processed even though the first fragment don't include all
headers through the upper layer header. This breaks TAHI IPv6 Core
Conformance Test v6LC.1.3.6.
Referring to RFC8200 SECTION 4.5: "If the first fragment does not include
all headers through an Upper-Layer header, then that fragment should be
discarded and an ICMP Parameter Problem, Code 3, message should be sent to
the source of the fragment, with the Pointer field set to zero."
The fragment needs to be validated the same way it is done in
commit 2efdaaaf883a ("IPv6: reply ICMP error if the first fragment don't
include all headers") for ipv6. Wrap the validation into a common function,
ipv6_frag_thdr_truncated() to check for truncation in the upper layer
header. This validation does not fullfill all aspects of RFC 8200,
section 4.5, but is at the moment sufficient to pass mentioned TAHI test.
In netfilter, utilize the fragment offset returned by find_prev_fhdr() to
let ipv6_frag_thdr_truncated() start it's traverse from the fragment
header.
Return 0 to drop the fragment in the netfilter. This is the same behaviour
as used on other protocol errors in this function, e.g. when
nf_ct_frag6_queue() returns -EPROTO. The Fragment will later be picked up
by ipv6_frag_rcv() in reassembly.c. ipv6_frag_rcv() will then send an
appropriate ICMP Parameter Problem message back to the source.
References commit 2efdaaaf883a ("IPv6: reply ICMP error if the first
fragment don't include all headers")
Signed-off-by: Georg Kohmann <geokohma@cisco.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/20201111115025.28879-1-geokohma@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Zhang Qilong says:
====================
Fix usage counter leak by adding a general sync ops
In many case, we need to check return value of pm_runtime_get_sync,
but it brings a trouble to the usage counter processing. Many callers
forget to decrease the usage counter when it failed, which could
resulted in reference leak. It has been discussed a lot[0][1]. So we
add a function to deal with the usage counter for better coding and
view. Then, we replace pm_runtime_resume_and_get with it in fec_main.c
to avoid it.
[0] https://lkml.org/lkml/2020/6/14/88
[1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139
====================
Link: https://lore.kernel.org/r/20201110092933.3342784-1-zhangqilong3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f8d0 ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In many case, we need to check return value of pm_runtime_get_sync, but
it brings a trouble to the usage counter processing. Many callers forget
to decrease the usage counter when it failed, which could resulted in
reference leak. It has been discussed a lot[0][1]. So we add a function
to deal with the usage counter for better coding.
[0]https://lkml.org/lkml/2020/6/14/88
[1]https://patchwork.ozlabs.org/project/linux-tegra/list/?series=178139
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Actually, burst size is equal to '1 << desc->rqcfg.brst_size'.
we should use burst size, not desc->rqcfg.brst_size.
dma memcpy performance on Rockchip RV1126
@ 1512MHz A7, 1056MHz LPDDR3, 200MHz DMA:
dmatest:
/# echo dma0chan0 > /sys/module/dmatest/parameters/channel
/# echo 4194304 > /sys/module/dmatest/parameters/test_buf_size
/# echo 8 > /sys/module/dmatest/parameters/iterations
/# echo y > /sys/module/dmatest/parameters/norandom
/# echo y > /sys/module/dmatest/parameters/verbose
/# echo 1 > /sys/module/dmatest/parameters/run
dmatest: dma0chan0-copy0: result #1: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #2: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #3: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #4: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #5: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #6: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #7: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #8: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
Before:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 48 iops 200338 KB/s (0)
After this patch:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 179 iops 734873 KB/s (0)
After this patch and increase dma clk to 400MHz:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 259 iops 1062929 KB/s (0)
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Link: https://lore.kernel.org/r/1605326106-55681-1-git-send-email-sugar.zhang@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit 7f832645d0e5 ("dmaengine: ioatdma: remove ioatdma v2 registration")
missed to remove dca2_tag_map_valid() during its removal. Hence, since
then, dca2_tag_map_valid() is unused and make CC=clang W=1 warns:
drivers/dma/ioat/dca.c:44:19:
warning: unused function 'dca2_tag_map_valid' [-Wunused-function]
So, remove this unused function and get rid of a -Wused-function warning.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113081248.26416-1-lukas.bulwahn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This fix is for a failure that occurred in the DWARF unwind perf test.
Stack unwinders may probe memory when looking for frames.
Memory sanitizer will poison and track uninitialized memory on the
stack, and on the heap if the value is copied to the heap.
This can lead to false memory sanitizer failures for the use of an
uninitialized value.
Avoid this problem by removing the poison on the copied stack.
The full msan failure with track origins looks like:
==2168==WARNING: MemorySanitizer: use-of-uninitialized-value
#0 0x559ceb10755b in handle_cfi elfutils/libdwfl/frame_unwind.c:648:8
#1 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4
#2 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7
#3 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10
#4 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17
#5 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17
#6 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14
#7 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10
#8 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8
#9 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8
#10 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#11 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#12 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#13 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#14 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#15 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#16 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#17 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#18 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#19 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#20 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#21 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#22 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#23 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was stored to memory at
#0 0x559ceb106acf in __libdwfl_frame_reg_set elfutils/libdwfl/frame_unwind.c:77:22
#1 0x559ceb106acf in handle_cfi elfutils/libdwfl/frame_unwind.c:627:13
#2 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4
#3 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7
#4 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10
#5 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17
#6 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17
#7 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14
#8 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10
#9 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8
#10 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8
#11 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#12 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#13 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#14 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#15 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#16 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#17 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#18 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#19 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#20 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#21 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#22 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#23 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#24 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was stored to memory at
#0 0x559ceb106a54 in handle_cfi elfutils/libdwfl/frame_unwind.c:613:9
#1 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4
#2 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7
#3 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10
#4 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17
#5 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17
#6 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14
#7 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10
#8 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8
#9 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8
#10 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#11 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#12 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#13 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#14 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#15 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#16 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#17 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#18 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#19 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#20 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#21 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#22 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#23 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was stored to memory at
#0 0x559ceaff8800 in memory_read tools/perf/util/unwind-libdw.c:156:10
#1 0x559ceb10f053 in expr_eval elfutils/libdwfl/frame_unwind.c:501:13
#2 0x559ceb1060cc in handle_cfi elfutils/libdwfl/frame_unwind.c:603:18
#3 0x559ceb105448 in __libdwfl_frame_unwind elfutils/libdwfl/frame_unwind.c:741:4
#4 0x559ceb0ece90 in dwfl_thread_getframes elfutils/libdwfl/dwfl_frame.c:435:7
#5 0x559ceb0ec6b7 in get_one_thread_frames_cb elfutils/libdwfl/dwfl_frame.c:379:10
#6 0x559ceb0ec6b7 in get_one_thread_cb elfutils/libdwfl/dwfl_frame.c:308:17
#7 0x559ceb0ec6b7 in dwfl_getthreads elfutils/libdwfl/dwfl_frame.c:283:17
#8 0x559ceb0ec6b7 in getthread elfutils/libdwfl/dwfl_frame.c:354:14
#9 0x559ceb0ec6b7 in dwfl_getthread_frames elfutils/libdwfl/dwfl_frame.c:388:10
#10 0x559ceaff6ae6 in unwind__get_entries tools/perf/util/unwind-libdw.c:236:8
#11 0x559ceabc9dbc in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:111:8
#12 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#13 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#14 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#15 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#16 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#17 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#18 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#19 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#20 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#21 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#22 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#23 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#24 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#25 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was stored to memory at
#0 0x559cea9027d9 in __msan_memcpy llvm/llvm-project/compiler-rt/lib/msan/msan_interceptors.cpp:1558:3
#1 0x559cea9d2185 in sample_ustack tools/perf/arch/x86/tests/dwarf-unwind.c:41:2
#2 0x559cea9d202c in test__arch_unwind_sample tools/perf/arch/x86/tests/dwarf-unwind.c:72:9
#3 0x559ceabc9cbd in test_dwarf_unwind__thread tools/perf/tests/dwarf-unwind.c:106:6
#4 0x559ceabca5cf in test_dwarf_unwind__compare tools/perf/tests/dwarf-unwind.c:138:26
#5 0x7f812a6865b0 in bsearch (libc.so.6+0x4e5b0)
#6 0x559ceabca871 in test_dwarf_unwind__krava_3 tools/perf/tests/dwarf-unwind.c:162:2
#7 0x559ceabca926 in test_dwarf_unwind__krava_2 tools/perf/tests/dwarf-unwind.c:169:9
#8 0x559ceabca946 in test_dwarf_unwind__krava_1 tools/perf/tests/dwarf-unwind.c:174:9
#9 0x559ceabcae12 in test__dwarf_unwind tools/perf/tests/dwarf-unwind.c:211:8
#10 0x559ceabbc4ab in run_test tools/perf/tests/builtin-test.c:418:9
#11 0x559ceabbc4ab in test_and_print tools/perf/tests/builtin-test.c:448:9
#12 0x559ceabbac70 in __cmd_test tools/perf/tests/builtin-test.c:669:4
#13 0x559ceabbac70 in cmd_test tools/perf/tests/builtin-test.c:815:9
#14 0x559cea960e30 in run_builtin tools/perf/perf.c:313:11
#15 0x559cea95fbce in handle_internal_command tools/perf/perf.c:365:8
#16 0x559cea95fbce in run_argv tools/perf/perf.c:409:2
#17 0x559cea95fbce in main tools/perf/perf.c:539:3
Uninitialized value was created by an allocation of 'bf' in the stack frame of function 'perf_event__synthesize_mmap_events'
#0 0x559ceafc5f60 in perf_event__synthesize_mmap_events tools/perf/util/synthetic-events.c:445
SUMMARY: MemorySanitizer: use-of-uninitialized-value elfutils/libdwfl/frame_unwind.c:648:8 in handle_cfi
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: clang-built-linux@googlegroups.com
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20201113182053.754625-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Portal size is 4k. Current code is mapping all 4 portals in a single chunk.
Restrict the mapped portal size to a single portal to ensure that submission
only goes to the intended portal address.
Fixes: c52ca478233c ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160513342642.510187.16450549281618747065.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
"perf inject" can create corrupt files when synthesizing sample events from AUX
data. This happens when in the input file, the first event (for the AUX data)
has a different sample_type from the second event (generally dummy).
Specifically, they differ in the bits that indicate the standard fields
appended to perf records in the mmap buffer. "perf inject" deletes the first
event and moves up the second event to first position.
The problem is with the synthetic PERF_RECORD_MMAP (etc.) events created
by "perf record".
Since these are synthetic versions of events which are normally produced
by the kernel, they have to have the standard fields appended as
described by sample_type.
"perf record" fills these in with zeroes, including the IDENTIFIER
field; perf readers interpret records with zero IDENTIFIER using the
descriptor for the first event in the file.
Since "perf inject" changes the first event, these synthetic records are
then processed with the wrong value of sample_type, and the perf reader
reads bad data, reports on incorrect length records etc.
Mismatching sample_types are seen with "perf record -e cs_etm//", where the AUX
event has TID|TIME|CPU|IDENTIFIER and the dummy event has TID|TIME|IDENTIFIER.
Perhaps they could be the same, but it isn't normally a problem if they aren't
- perf has no problems reading the file.
The sample_types have to agree on the position of IDENTIFIER, because
that's how perf finds the right event descriptor in the first place, but
they don't normally have to agree on other fields, and perf doesn't
check that they do.
The problem is specific to the way "perf inject" reorganizes the events
and the way synthetic MMAP events are recorded with a zero identifier. A
simple solution is to stop "perf inject" deleting the tracing event.
Committer testing
Removed the now unused 'evsel' variable, update the comment about the
evsel removal not being performed anymore, and apply the patch manually
as it failed with this warning:
warning: Patch sent with format=flowed; space at the end of lines might be lost.
Testing it with:
$ perf bench internals inject-build-id
# Running 'internals/inject-build-id' benchmark:
Average build-id injection took: 8.543 msec (+- 0.130 msec)
Average time per event: 0.838 usec (+- 0.013 usec)
Average memory usage: 12717 KB (+- 9 KB)
Average build-id-all injection took: 5.710 msec (+- 0.058 msec)
Average time per event: 0.560 usec (+- 0.006 usec)
Average memory usage: 12079 KB (+- 7 KB)
$
Signed-off-by: Al Grant <al.grant@arm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LPU-Reference: b9cf5611-daae-2390-3439-6617f8f0a34b@foss.arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.10, round 4:
- Fix MDIO over clocking on vf610-zii-dev-rev-b board to get switch
device work reliably.
- Fix imx50-evk IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
- Fix voltage for 1.6GHz CPU operating point on i.MX8MM to match
hardware datasheet.
- Fix phy-mode for KSZ9031 PHY on imx6qdl-udoo board.
* tag 'imx-fixes-5.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx50-evk: Fix the chip select 1 IOMUX
arm64: dts: imx8mm: fix voltage for 1.6GHz CPU operating point
ARM: dts: vf610-zii-dev-rev-b: Fix MDIO over clocking
arm: dts: imx6qdl-udoo: fix rgmii phy-mode for ksz9031 phy
Link: https://lore.kernel.org/r/20201116090702.GM5849@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.10
- Add missing audio clock on RZ/G2H.
* tag 'renesas-fixes-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a774e1: Add missing audio_clk_b
Link: https://lore.kernel.org/r/20201113151229.3924165-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-11-15
Anant Thazhemadam contributed two patches for the AF_CAN that prevent potential
access of uninitialized member in can_rcv() and canfd_rcv().
The next patch is by Alejandro Concepcion Rodriguez and changes can_restart()
to use the correct function to push a skb into the networking stack from
process context.
Zhang Qilong's patch fixes a memory leak in the error path of the ti_hecc's
probe function.
A patch by me fixes mcba_usb_start_xmit() function in the mcba_usb driver, to
first fill the skb and then pass it to can_put_echo_skb().
Colin Ian King's patch fixes a potential integer overflow on shift in the
peak_usb driver.
The next two patches target the flexcan driver, a patch by me adds the missing
"req_bit" to the stop mode property comment (which was broken during net-next
for v5.10). Zhang Qilong's patch fixes the failure handling of
pm_runtime_get_sync().
The next seven patches target the m_can driver including the tcan4x5x spi
driver glue code. Enric Balletbo i Serra's patch for the tcan4x5x Kconfig fix
the REGMAP_SPI dependency handling. A patch by me for the tcan4x5x driver's
probe() function adds missing error handling to for devm_regmap_init(), and in
tcan4x5x_can_remove() the order of deregistration is fixed. Wu Bo's patch for
the m_can driver fixes the state change handling in
m_can_handle_state_change(). Two patches by Dan Murphy first introduce
m_can_class_free_dev() and then make use of it to fix the freeing of the can
device. A patch by Faiz Abbas add a missing shutdown of the CAN controller in
the m_can_stop() function.
* tag 'linux-can-fixes-for-5.10-20201115' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: m_can_stop(): set device to software init mode before closing
can: m_can: Fix freeing of can device from peripherials
can: m_can: m_can_class_free_dev(): introduce new function
can: m_can: m_can_handle_state_change(): fix state change
can: tcan4x5x: tcan4x5x_can_remove(): fix order of deregistration
can: tcan4x5x: tcan4x5x_can_probe(): add missing error checking for devm_regmap_init()
can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI
can: flexcan: fix failure handling of pm_runtime_get_sync()
can: flexcan: flexcan_setup_stop_mode(): add missing "req_bit" to stop mode property comment
can: peak_usb: fix potential integer overflow on shift of a int
can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb()
can: ti_hecc: Fix memleak in ti_hecc_probe
can: dev: can_restart(): post buffer from the right context
can: af_can: prevent potential access of uninitialized member in canfd_rcv()
can: af_can: prevent potential access of uninitialized member in can_rcv()
====================
Link: https://lore.kernel.org/r/20201115174131.2089251-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd3430d ("s390/dasd: fix handling of internal requests")
Cc: <stable@vger.kernel.org> #4.16
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add HD Audio PCI ID and HDMI codec vendor ID for Intel Alder Lake.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201116141955.2091240-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The following warning is reported if lock debugging is enabled.
DEBUG_LOCKS_WARN_ON(1)
WARNING: CPU: 1 PID: 1 at kernel/locking/lockdep.c:4617 lockdep_init_map_waits+0x141/0x222
...
Call Trace:
__kernfs_create_file+0x7a/0xd8
sysfs_add_file_mode_ns+0x135/0x189
sysfs_create_file_ns+0x70/0xa0
acpi_fan_probe+0x547/0x621
platform_drv_probe+0x67/0x8b
...
Dynamically allocated sysfs attributes need to be initialized to avoid
the warning.
Fixes: d19e470b6605 ("ACPI: fan: Expose fan performance state information")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
pci_dev::physfn is only available when CONFIG_PCI_ATS is set. The recent
fix for the irqdomain rework missed that dependency which makes the build
fail when CONFIG_PCI_ATS=n.
Add the necessary #ifdeffery.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: ff828729be44 ("iommu/vt-d: Cure VF irqdomain hickup")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joerg Roedel <joro@8bytes.org>
|
