| Age | Commit message (Collapse) | Author |
|---|
|
Prior to this patch:
~# cat /proc/interrupts
...
40: 123 0 GIC-0 72 Level altera_uart
41: 9 0 GIC-0 73 Level altera_uart
After this patch:
~# cat /proc/interrupts
...
40: 6 0 GIC-0 72 Level ff200100.fpga-uart0
41: 28 0 GIC-0 73 Level ff200200.fpga-uart1
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20231217195601.236002-1-antonynpavlov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add "SER_RS485_MODE_RS422" flag to struct serial_rs485, so that serial
port can switch interface into RS422 if supported by using ioctl command
"TIOCSRS485".
By treating RS422 as a mode of RS485, which means while enabling RS422
there are two flags need to be set (SER_RS485_ENABLED and
SER_RS485_MODE_RS422), it would make things much easier. For example
some places that checks for "SER_RS485_ENABLED" won't need to be rewritten.
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Link: https://lore.kernel.org/r/20231201071554.258607-3-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch replaces the bit shift code with "_BITUL()" macro inside
"serial_rs485" struct.
Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@moxa.com>
Link: https://lore.kernel.org/r/20231201071554.258607-2-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename the variable size to temp and change its data type from
unsigned int to u64 to avoid type casting in multiplication. Remove the
intermediate variable frame_time and use temp instead to accommodate
the nanoseconds(ns). port->frame_time is an unsigned int, therefore an
explicit cast is used to improve readability. Having said this unsigned
int is sufficinet to hold frame time duration in nanoseconds for all
the standard baudrates.
Consider 9600 baud, it takes 1/9600 seconds for one bit, for a total of
10 bits (start, 8-bit data, stop) 10/9600=1.04 ms for 1 byte transfer,
frame_time here is 1041667ns. As baudrate increases frame_time
decreases, say for 115200 baud it is 86806ns.
To avoid costly 64-bit arithmetic we do not upconvert the type for
variable frame_time as overflow happens for extremely low baudrates
which are impractical and are not used in real-world applications.
Signed-off-by: Vamshi Gajjela <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20231109063417.3971005-3-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function uart_fifo_timeout() returns an unsigned long value, which
is the number of jiffies. Therefore, change the variable timeout in the
function uart_poll_timeout() from int to unsigned long.
Change the return type of the function uart_poll_timeout() from int to
unsigned long to be consistent with the type of timeout values.
Signed-off-by: Vamshi Gajjela <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20231109063417.3971005-2-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure that the number of XHCI secondary interrupters defined for a DWC3
based implementation is limited to 8. XHCI in general can potentially
support up to 1024 interrupters.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240102214549.22498-16-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the definition for how many interrupts the XHCI host controller should
allocate. XHCI can potentially support up to 1024 interrupters, which
implementations may want to limit.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240102214549.22498-15-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Modify the XHCI drivers to accommodate for handling multiple event rings in
case there are multiple interrupters. Add the required APIs so clients are
able to allocate/request for an interrupter ring, and pass this information
back to the client driver. This allows for users to handle the resource
accordingly, such as passing the event ring base address to an audio DSP.
There is no actual support for multiple MSI/MSI-X vectors.
[export xhci_initialize_ring_info() -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240102214549.22498-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is usbdrv_wrap in struct usb_driver and usb_device_driver, it
contains device_driver and for_devices. for_devices is used to
distinguish between device drivers and interface drivers.
Like the is_usb_device(), it tests the type of the device. We can test
that if the probe of device_driver is equal to usb_probe_device in
is_usb_device_driver(), and then the struct usbdrv_wrap is no longer
needed.
Clean up struct usbdrv_wrap, use device_driver directly in struct
usb_driver and usb_device_driver. This makes the code cleaner.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240104032822.1896596-1-yajun.deng@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the quirk property "rx-fifo-depth" to work around Gen1 isoc-in
transfer issue which send out unexpected ACK even after device
already finished the burst transfer with a short patcket, specially
for a 4K camera device.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-3-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For Gen1 isoc-in transfer, host still send out unexpected ACK after device
finish the burst with a short packet, this will cause an exception on the
connected device, such as, a usb 4k camera.
It can be fixed by setting rxfifo depth less than 4k bytes, prefer to use
3k here, the side-effect is that may cause performance drop about 10%,
including bulk transfer.
Fixes: 926d60ae64a6 ("usb: xhci-mtk: modify the SOF/ITP interval for mt8195")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For Gen1 isoc-in endpoint on controller before about SSUSB IPM v1.6.0, it
still send out unexpected ACK after receiving a short packet in burst
transfer, this will cause an exception on connected device, specially for
a 4k camera.
Add a quirk property "rx-fifo-depth" to work around this hardware issue,
prefer to use 3k bytes;
The side-effect is that it may cause performance drop about 10%, including
bulk transfer.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The PNoC clock is a clock for the entire PNoC bus, managed from
within the interconnect driver. Attaching it to MSS was a total hack.
Get rid of it and take the liberty to make the clock-names entries
more readable.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-9-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The AGGRE2 clock is a clock for the entire AGGRE2 bus, managed from
within the interconnect driver. Attaching it to SLPI was a total hack.
Get rid of it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-8-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The AGGRE2 clock is a clock for the entire AGGRE2 bus, managed from
within the interconnect driver. Attaching it to SLPI was a total hack.
Get rid of it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-7-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.
These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-6-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.
These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-5-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.
These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-4-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.
These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-3-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some nodes are abusingly referencing some of the internal bus clocks,
that were recently removed in Linux (because the original implementation
did not make much sense), managing them as if they were the only devices
on an NoC bus.
These clocks are now handled from within the icc framework and are
no longer registered from within the CCF. Remove them.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-2-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SDM660 was abusingly referencing one of the internal bus clocks, that
were recently dropped from Linux (because the original implementation
did not make much sense), circumventing the interconnect framework.
Drop it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-1-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For wakeup to work, driver needs to enable interrupts that depict what is
happening on the DP/DM lines. On QUSB targets, this is identified by
qusb2_phy whereas on SoCs using Femto PHY, separate {dp,dm}_hs_phy_irq's
are used instead.
The implementation incorrectly names qusb2_phy interrupts as "hs_phy_irq".
Clean this up so that driver would be using only qusb2/(dp & dm) for wakeup
purposes.
For devices running older kernels, this won't break any functionality
because the interrupt configurations in QUSB2 PHY based SoCs is done
by configuring QUSB2PHY_INTR_CTRL register in PHY address space and it was
never armed properly right from the start.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231227091951.685-3-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The high speed related interrupts present on QC targets are as follows:
1. dp/dm irq's
These IRQ's directly reflect changes on the DP/DM pads of the SoC. These
are used as wakeup interrupts only on SoCs with non-QUSB2 targets with
exception of SDM670/SDM845/SM6350.
2. qusb2_phy irq
SoCs with QUSB2 PHY do not have separate DP/DM IRQs and expose only a
single IRQ whose behavior can be modified by the QUSB2PHY_INTR_CTRL
register. The required DPSE/DMSE configuration is done in
QUSB2PHY_INTR_CTRL register of phy address space.
3. hs_phy_irq
This is completely different from the above two and is present on all
targets with exception of a few IPQ ones. The interrupt is not enabled by
default and its functionality is mutually exclusive of qusb2_phy on QUSB
targets and DP/DM on femto phy targets.
The DTs of several QUSB2 PHY based SoCs incorrectly define "hs_phy_irq"
when they should have been "qusb2_phy_irq". On Femto phy targets, the
"hs_phy_irq" mentioned is either the actual "hs_phy_irq" or "pwr_event",
neither of which would never be triggered directly are non-functional
currently. The implementation tries to clean up this issue by addressing
the discrepencies involved and fixing the hs_phy_irq's in respective DT's.
Classify SoC's into four groups based on whether qusb2_phy interrupt
or {dp/dm}_hs_phy_irq is used for wakeup in high speed and whether the
SoCs have hs_phy_irq present in them or not. The ss_phy_irq is optional
interrupt because there are mutliple SoC's which either support only High
Speed or there are multiple controllers within same Soc and the secondary
controller is High Speed only capable.
This breaks ABI on targets running older kernels, but since the interrupt
definitions are given wrong on many targets and to establish proper rules
for usage of DWC3 interrupts on Qualcomm platforms, DT binding update is
necessary. The bindings put pwr_event as the first interrupt and ss_phy as
the last. Since all SoCs have the pwr_event (HS) interrupt, but not all
controllers have the SS PHY interrupt, this would prevent, to some extent,
expressing that the SS PHY is optional by keeping it last in the binding
schema and making sure that minItems = maxItems - 1.
No new targets have been added to schema. Only the existing ones have been
re-ordered.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231227091951.685-2-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In 6.7-rc1, there was a netif_device_detach call added to the
gether_disconnect function. This clears the __LINK_STATE_PRESENT bit of
the netif device and suppresses pings (ICMP messages) and TCP connection
requests from the connected host. If userspace temporarily disconnects
the gadget, such as by temporarily removing configuration in the gadget
configfs interface, network activity should continue to be processed
when the gadget is re-connected. Mirror the netif_device_detach call
with a netif_device_attach call in gether_connect to fix re-connecting
gadgets.
Link: https://gitlab.com/postmarketOS/pmaports/-/tree/6002e51b7090aeeb42947e0ca7ec22278d7227d0/main/postmarketos-base-ui/rootfs-usr-lib-NetworkManager-dispatcher.d-50-tethering.sh
Cc: stable <stable@kernel.org>
Fixes: f49449fbc21e ("usb: gadget: u_ether: Replace netif_stop_queue with netif_device_detach")
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Tested-by: Duje Mihanović <duje.mihanovic@skole.hr>
Link: https://lore.kernel.org/r/20231218164532.411125-2-mailingradian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.
The exact condition is seen with the following sequence:
1. USB bus reset is issued by the host
2. Shortly after, or concurrently, a USB PD DR SWAP request is received
(sink->source)
3. USB bus reset event handler runs and issues
dwc3_stop_active_transfers(), and pending transfer are stopped
4. DWC3 usage_count decremented to 0, and runtime idle occurs while
dwc->connected == true, returns -EBUSY
5. DWC3 disconnect event seen, dwc->connected set to false due to DR
swap handling
6. No runtime idle after this point
Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.
Fixes: fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240103214946.2596-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When CONFIG_USB_OTG is not set, mxs_phy_is_otg_host() will always return
false. This behaviour is wrong. Since phy.last_event will always be set
for either host or device mode. Therefore, CONFIG_USB_OTG condition
can be removed.
Fixes: 5eda42aebb76 ("usb: phy: mxs: fix getting wrong state with mxs_phy_is_otg_host()")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the chipidea driver introduce extcon for id and vbus, it's able
to wakeup from another irq source, in case the system with extcon ID
cable, wakeup from usb ID cable and device removal, the usb device
disconnect irq may come firstly before the extcon notifier while system
resume, so we will get 2 "wakeup" irq, one for usb device disconnect;
and one for extcon ID cable change(real wakeup event), current driver
treat them as 2 successive wakeup irq so can't handle it correctly, then
finally the usb irq can't be enabled. This patch adds a check to bypass
further usb events before controller resume finished to fix it.
Fixes: 1f874edcb731 ("usb: chipidea: add runtime power management support")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20231228110753.1755756-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some platform using ChipIdea IP may keep 32KHz wakeup clock always
on without usb driver intervention. And some may need driver to handle
this clock. For now only i.MX93 needs this wakeup clock. This patch will
get wakeup clock and keep it always on to make controller work properly.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20231228110753.1755756-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 3c5b006f3ee800b4bd9ed37b3a8f271b8560126e.
gadget_is_{super|dual}speed() API check UDC controller capitblity. It
should pass down highest speed endpoint descriptor to UDC controller. So
UDC controller driver can reserve enough resource at check_config(),
especially mult and maxburst. So UDC driver (such as cdns3) can know need
at least (mult + 1) * (maxburst + 1) * wMaxPacketSize internal memory for
this uvc functions.
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-5-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Supposed DMA cross 4k bounder problem should be fixed at DEV_VER_V2, but
still met problem when do ISO transfer if sg enabled.
Data pattern likes below when sg enabled, package size is 1k and mult is 2
[UVC Header(8B) ] [data(3k - 8)] ...
The received data at offset 0xd000 will get 0xc000 data, len 0x70. Error
happen position as below pattern:
0xd000: wrong
0xe000: wrong
0xf000: correct
0x10000: wrong
0x11000: wrong
0x12000: correct
...
To avoid DMA cross 4k bounder at ISO transfer, reduce burst len according
to start DMA address's alignment.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-4-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ISO basic transfer is
ITP(SOF) Package_0 Package_1 ... Package_n
CDNS3 DMA start dma transfer from memmory to internal FIFO when get SOF,
controller will transfer data to usb bus from internal FIFO when get IN
token.
According USB spec defination:
Maximum number of packets = (bMaxBurst + 1) * (Mult + 1)
Internal memory should be the same as (bMaxBurst + 1) * (Mult + 1). DMA
don't fetch data advance when ISO transfer, so only reserve
(bMaxBurst + 1) * (Mult + 1) internal memory for ISO transfer.
Need save Mult and bMaxBurst information and set it into EP_CFG register,
otherwise only 1 package is sent by controller, other package will be
lost.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-3-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When IP version >= DEV_VER_V2, gadget:sg_supported is true. So uvc gadget
function driver will use sg to equeue data, first is 8bytes header, the
second is 1016bytes data.
cdns3_prepare_trb: ep2in: trb 0000000000ac755f, dma buf: 0xbf455000, size: 8, burst: 128 ctrl: 0x00000415 (C=1, T=0, ISP, CHAIN, Normal)
cdns3_prepare_trb: ep2in: trb 00000000a574e693, dma buf: 0xc0200fe0, size: 1016, burst: 128 ctrl: 0x00000405 (C=1, T=0, ISP, Normal)
But cdns3_ep_run_transfer() can't correctly handle this case, which only
support one TRB for ISO transfer.
The controller requires duplicate the TD for each SOF if priv_ep->interval
is not 1. DMA will read data from DDR to internal FIFO when get SOF. Send
data to bus when receive IN token. DMA always refill FIFO when get SOF
regardless host send IN token or not. If host send IN token later, some
frames data will be lost.
Fixed it by below major steps:
1. Calculate numembers of TRB base on sg_nums and priv_ep->interval.
2. Remove CHAIN flags for each end TRB of TD when duplicate TD.
3. The controller requires LINK TRB must be first TRB of TD. When check
there are not enough TRBs lefts, just fill LINK TRB for left TRBs.
.... CHAIN_TRB DATA_TRB, CHAIN_TRB DATA_TRB, LINK_TRB ... LINK_TRB
^End of TRB List
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231224153816.1664687-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The process book is arguably the most important documentation we have; the
top three trafficked pages on docs.kernel.org are found here. Make a
beginning effort to impose a more useful organization on this page to ease
developers into the community.
Acked-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
The max segment size is currently limited to the ethernet frame length of
the kernel which happens to be 1514 at this point in time. However the NCM
specification limits it to 64K for sixtenn bit NTB's. For peer to peer
connections, increasing the segment size gives better throughput.
Add support to configure this value before configfs symlink is created.
Also since the NTB Out/In buffer sizes are fixed at 16384 bytes, limit the
segment size to an upper cap of 8000 to allow at least a minimum of 2 MTU
sized datagrams to be aggregated.
Set the default MTU size for the ncm interface during function bind before
network interface is registered allowing MTU to be set in parity with
wMaxSegmentSize.
Update gadget documentation describing the new configfs property.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20231221153216.18657-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For device mode, if PM runtime autosuspend feature enabled, the
runtime power status of dwc3 may be suspended when run dwc3_resume(),
and dwc3 gadget would not be configured in dwc3_gadget_run_stop().
It would cause gadget connected failed if USB cable has been plugged
before PM resume. So move forward pm_runtime_set_active() to fix it.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Link: https://lore.kernel.org/r/20231206065939.16958-1-frank.wang@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Support configuration and use of bulk endpoints in the so-called EBC
mode described in the DBC_usb31 databook (appendix E)
Added a bit fifo_mode to usb_ep to indicate to the UDC driver that a
specific endpoint is to operate in the EBC (or equivalent) mode when
enabled
Added macros for bits 15 and 14 of DEPCFG parameter 1 to indicate EBC
mode and write back behaviour. These bits will be set to 1 when
configuring an EBC endpoint as described in the programming guide
Signed-off-by: Manan Aurora <maurora@google.com>
Link: https://lore.kernel.org/r/20231031034641.660606-1-maurora@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor tcpm_fw_get_caps to support the multiple pd capabilities got
from fwnode. For backward compatibility, the original single capability
is still applicable. The fetched data is stored in the newly defined
structure "pd_data" and there is an array "pd_list" to store the
pointers to them. A dedicated array "pds" is used to store the handles
of the registered usb_power_delivery instances.
Also implement the .pd_get and .pd_set ops which are introduced in
commit a7cff92f0635 ("usb: typec: USB Power Delivery helpers for ports
and partners"). Once the .pd_set is called, the current capability will
be updated and state machine will re-negotiate the power contract if
possible.
Signed-off-by: Kyle Tso <kyletso@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231216104630.2720818-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 662a60102c12 ("usb: typec: Separate USB Power Delivery from USB
Type-C") allows userspace to configure the PD of a port by selecting
different set of predefined PD capabilities. Define the PD capability
sets in DT for better configurability in device modules.
Define an optional child node "capabilities" to contain multiple USB
Power Delivery capabilities.
Define child nodes with pattern (e.g. caps-0, caps-1) under
"capabilities". Each node contains PDO data of a selectable Power
Delivery capability.
Also define common properties for source-pdos, sink-pdos, and
op-sink-microwatt that can be referenced.
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20231205030114.1349089-2-kyletso@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231216104630.2720818-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xhci retaining bogus hardware states cause usb disconnect devices
connected before hibernation(s4) and refer to the commit 'f3d478858be
("usb: ohci-platform: fix usb disconnect issue after s4")' which set
flag "hibernated" as true when resume-from-hibernation and that the
drivers will reset the hardware to get rid of any existing state and
make sure resume from hibernation re-enumerates everything for xhci.
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
Link: https://lore.kernel.org/r/20231228071113.1719-1-zhuyinbo@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently for dwc3_usb31 controller, if maximum_speed is limited to
super-speed in DT, then device mode is limited to SS, but host mode
still works in SSP.
The documentation for max-speed property is as follows:
"Tells USB controllers we want to work up to a certain speed.
Incase this isn't passed via DT, USB controllers should default to
their maximum HW capability."
It doesn't specify that the property is only for device mode.
There are cases where we need to limit the host's maximum speed to
SuperSpeed only. Use this property for host mode to contrain host's
speed to SuperSpeed.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231219041559.15789-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current implementation blocks the running operations when Plug-out and
Plug-In is performed continuously, process gets stuck in
dwc3_thread_interrupt().
Code Flow:
CPU1
->Gadget_start
->dwc3_interrupt
->dwc3_thread_interrupt
->dwc3_process_event_buf
->dwc3_process_event_entry
->dwc3_endpoint_interrupt
->dwc3_ep0_interrupt
->dwc3_ep0_inspect_setup
->dwc3_ep0_stall_and_restart
By this time if pending_list is not empty, it will get the next request
on the given list and calls dwc3_gadget_giveback which will unmap request
and call its complete() callback to notify upper layers that it has
completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET,
whereas it should be -ESHUTDOWN based on condition if not dwc->connected
is true.
Cc: <stable@vger.kernel.org>
Fixes: d742220b3577 ("usb: dwc3: ep0: giveback requests on stall_and_restart")
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20231222094704.20276-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A freezable kernel thread can enter frozen state during freezing by
either calling try_to_freeze() or using wait_event_freezable() and its
variants. So for the following snippet of code in a kernel thread loop:
wait_event_interruptible_timeout();
try_to_freeze();
We can change it to a simple wait_event_freezable_timeout() and
then eliminate a function call.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Link: https://lore.kernel.org/r/20231218074730.1898699-1-haokexin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use gpu_metrics_v1_5 for SMUv13.0.6 to fill
gpu metric info
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add new gpu_metrics_v1_5 to acquire vcn/jpeg activity
& pcie nak error counters
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Expose sysfs entry mem_busy_percent for GC version
9.4.3 APU system
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
without PSR
The check for sending the vsc infopacket to the display was gated behind
PSR (Panel Self Refresh) being enabled.
The vsc infopacket also contains the colorimetry (specifically the
container color gamut) information for the stream on modern DP.
PSR is typically only supported on mobile phone eDP displays, thus this
was not getting sent for typical desktop monitors or TV screens.
This functionality is needed for proper HDR10 functionality on DP as it
wants BT2020 RGB/YCbCr for the container color space.
Cc: stable@vger.kernel.org
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Xaver Hugl <xaver.hugl@gmail.com>
Cc: Melissa Wen <mwen@igalia.com>
Fixes: 15f9dfd545a1 ("drm/amd/display: Register Colorspace property for DP and HDMI")
Tested-by: Simon Berz <simon@berz.me>
Tested-by: Xaver Hugl <xaver.hugl@kde.org>
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's no longer required.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2318
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This was included in gpu_info firmware, move it into the
driver for consistency with other nv1x parts.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2318
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfs updates from David Howells:
A few follow-up fixes for the netfs work for this cycle.
* tag 'netfs-lib-20240104' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Fix proc/fs/fscache symlink to point to "netfs" not "../netfs"
netfs: Rearrange netfs_io_subrequest to put request pointer first
9p: Use length of data written to the server in preference to error
9p: Do a couple of cleanups
9p: Fix initialisation of netfs_inode for 9p
cachefiles: Fix __cachefiles_prepare_write()
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Current EP0 dequeue path will share the same as other EPs. However, there
are some special considerations that need to be made for EP0 transfers:
- EP0 transfers never transition into the started_list
- EP0 only has one active request at a time
In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to. While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command. If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.
In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed. However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.
Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled. This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.
Fixes: fcd2def66392 ("usb: dwc3: gadget: Refactor dwc3_gadget_ep_dequeue")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231206201814.32664-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
