summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-08-07igb: add delay to allow igb loopback test to succeed on 8086:10c9Stefan Assmann
Some 8086:10c9 NICs have a problem completing the ethtool loopback test. The result looks like this: ethtool -t eth1 The test result is FAIL The test extra info: Register test (offline) 0 Eeprom test (offline) 0 Interrupt test (offline) 0 Loopback test (offline) 13 Link test (on/offline) 0 A bisect clearly points to commit a95a07445ee97a2fef65befafbadcc30ca1bd145. However that seems to only trigger the bug. While adding some printk the problem disappeared, so this might be a timing issue. After some trial and error I discovered that adding a small delay just before igb_write_phy_reg() in igb_integrated_phy_loopback() allows the loopback test to succeed. I was unable to figure out the root cause so far but I expect it to be somewhere in the following executing path igb_integrated_phy_loopback ->igb_write_phy_reg_igp ->igb_write_phy_reg_mdic ->igb_acquire_phy_82575 ->igb_acquire_swfw_sync_82575 The problem could only be observed on 8086:10c9 NICs so far and not all of them show the behaviour. I did not restrict the workaround to this type of NIC as it should do no harm to other igb NICs. With the patch below the loopback test succeeded 500 times in a row using a NIC that would otherwise fail. Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
2012-08-07e1000e: 82571 Tx Data Corruption during Tx hang recoveryTushar Dave
A bus trace shows that while executing e1000e_down, TCTL is cleared except for the PSP bit. This occurs while in the middle of fetching a TSO packet since the Tx packet buffer is full at that point. Before the device is reset, the e1000_watchdog_task starts to run from the middle (it was apparently pre-empted earlier, although that is not in the trace) and sets TCTL.EN. At that point, 82571 transmits the corrupted packet, apparently because TCTL.MULR was cleared in the middle of fetching a packet, which is forbidden. Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of clearing the entire register, so as not to change any settings in the middle of fetching a packet. Signed-off-by: Tushar Dave <tushar.n.dave@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
2012-08-07e1000e: NIC goes up and immediately goes downTushar Dave
Found that commit d478eb44 was a bad commit. If the link partner is transmitting codeword (even if NULL codeword), then the RXCW.C bit will be set so check for RXCW.CW is unnecessary. Ref: RH BZ 840642 Reported-by: Fabio Futigami <ffutigam@redhat.com> Signed-off-by: Tushar Dave <tushar.n.dave@intel.com> CC: Marcelo Ricardo Leitner <mleitner@redhat.com> CC: stable <stable@vger.kernel.org> [2.6.38+] Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
2012-08-07i.MX27: Fix emma-prp and csi clocks.Javier Martin
Naming of emma-prp related clocks for the i.MX27 is not correct. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2012-08-07drivers/gpio/gpio-langwell.c: fix error return codeJulia Lawall
Convert a 0 error return code to a negative one, as returned elsewhere in the function. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e,e1,e2,e3,e4,x; @@ ( if (\(ret != 0\|ret < 0\) || ...) { ... return ...; } | ret = 0 ) ... when != ret = e1 *x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...); ... when != x = e2 when != ret = e3 *if (x == NULL || ...) { ... when != ret = e4 * return ret; } // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-08-07gpio: samsung: Fix off-by-one bug in gpio addressesSean Paul
Move gpc4 to the end of the automatically processed gpio controllers so we don't taint the automatic offset calculation. This bug caused all controllers coming after gpc4 to map to the incorrect address. The result is <&gpd1 0 0 0 0> would actually map to GPIO 0 in gpd0. Signed-off-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org> Acked-by: Doug Anderson <dianders@chromium.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-08-07ARM: dts: imx: add alias for gpioShawn Guo
Add alias for gpio nodes, so that gpio driver can identify the port number and then specify a sensible gpio base rather than using the one dynamically allocated by gpio core. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-08-07gpio/mxc: specify gpio base for device tree probeShawn Guo
Currently, unlike the non-DT probe where the gpio base is specified with pdev->id, the DT probe uses the base dynamically allocated by gpio core, which uses a completely different numbering scheme. This causes two issues to user space applications which access sysfs entry /sys/class/gpio/gpioN. * It breaks the compatibility with user space applications between non-DT and DT kernels. * It's not intuitive and sometimes hard for users to map the Linux gpio number to the actual hardware pin. Use alias to identify the gpio port/bank, and then the gpio base can be specified with port id to solve above issues. If alias is not defined in device tree, the base number dynamically allocated by gpio core will be used. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-08-07gpio/mxc: remove redundant shadow variables initializationShawn Guo
With commit 3e11f7b (gpio/generic: initialize basic_mmio_gpio shadow variables properly) in place, the shadow variables initialization is being done in generic driver bgpio_init call. Remove the redundant shadow variables initialization from gpio-mxc driver. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-08-07ALSA: hda - add dock support for Thinkpad X230Felix Kaechele
As with the ThinkPad Models X230 Tablet and T530 the X230 needs a qurik to correctly set up the pins for the dock port. Signed-off-by: Felix Kaechele <felix@fetzig.org> Cc: <stable@vger.kernel.org> [v3.2+] Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-08-06net: ipv6: fix TCP early demuxEric Dumazet
IPv6 needs a cookie in dst_check() call. We need to add rx_dst_cookie and provide a family independent sk_rx_dst_set(sk, skb) method to properly support IPv6 TCP early demux. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06net: Use PTR_RET rather than if(IS_ERR(.. [1]Thomas Meyer
The semantic patch that makes this change is available in scripts/coccinelle/api/ptr_ret.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/ Signed-off-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06net_sched: act: Delete estimator in error path.Hiroaki SHIMODA
Some action modules free struct tcf_common in their error path while estimator is still active. This results in est_timer() dereference freed memory. Add gen_kill_estimator() in ipt, pedit and simple action. Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06ip: fix error handling in ip_finish_output2()Vasiliy Kulikov
__neigh_create() returns either a pointer to struct neighbour or PTR_ERR(). But the caller expects it to return either a pointer or NULL. Replace the NULL check with IS_ERR() check. The bug was introduced in a263b3093641fb1ec377582c90986a7fd0625184 ("ipv4: Make neigh lookups directly in output packet path."). Signed-off-by: Vasily Kulikov <segoon@openwall.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06llc: free the right skbSorin Dumitru
We are freeing skb instead of nskb, resulting in a double free on skb and a leak from nskb. Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06ixp4xx_eth: fix ptp_ixp46x build failureArnaud Patard (Rtp)
When building with ixp4xx_eth and ptp_ixp46x as module, one is getting the following error: ERROR: "ixp46x_phc_index" [drivers/ptp/ptp_ixp46x.ko] undefined! This has been introduced by commit 509a7c25729feab353502e1b544c614772a1d49a. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06drivers/atm/iphase.c: fix error return codeJulia Lawall
Convert a 0 error return code to a negative one, as returned elsewhere in the function. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier ret; expression e,e1,e2,e3,e4,x; @@ ( if (\(ret != 0\|ret < 0\) || ...) { ... return ...; } | ret = 0 ) ... when != ret = e1 *x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...); ... when != x = e2 when != ret = e3 *if (x == NULL || ...) { ... when != ret = e4 * return ret; } // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06tcp_output: fix sparse warning for tcp_wfreeSilviu-Mihai Popescu
Fix sparse warning: * symbol 'tcp_wfree' was not declared. Should it be static? Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06drivers/net/phy/mdio-mux-gpio.c: drop devm_kfree of devm_kzalloc'd dataJulia Lawall
devm_kfree should not have to be explicitly used. The semantic patch that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,d; @@ x = devm_kzalloc(...) ... ?-devm_kfree(d,x); // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06batman-adv: select an internet gateway if none was chosenMarek Lindner
This is a regression introduced by: 2265c141086474bbae55a5bb3afa1ebb78ccaa7c ("batman-adv: gateway election code refactoring") Reported-by: Nicolás Echániz <nicoechaniz@codigosur.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Acked-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06mISDN: Bugfix for layer2 fixed TEI modeKarsten Keil
If a fixed TEI is used, the initial state of the layer 2 statmachine need to be 4 (TEI assigned). This was true only for Point to Point connections, but not for the other fixed TEIs. It was not found before, because usually only the TEI 0 is used as fixed TEI for PtP mode, but if you try X31 packet mode connections with SAPI 16, TEI 1, it did fail. Signed-off-by: Karsten Keil <keil@b1-systems.de> Cc: <stable@vger.kernel.org> # 3.5.x Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-06Bluetooth: add support for atheros 0489:e057Peng Chen
Add support for the AR3012 chip found on Fioxconn. usb-devices shows: T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 44 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e057 Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06iwlwifi: disable greenfield transmissions as a workaroundJohannes Berg
There's a bug that causes the rate scaling to get stuck when it has to use single-stream rates with a peer that can do GF and SGI; the two are incompatible so we can't use them together, but that causes the algorithm to not work at all, it always rejects updates. Disable greenfield for now to prevent that problem. Cc: stable@vger.kernel.org Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Tested-by: Cesar Eduardo Barros <cesarb@cesarb.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-06rt61pci: fix NULL pointer dereference in config_lna_gainStanislaw Gruszka
We can not pass NULL libconf->conf->channel to rt61pci_config() as it is dereferenced unconditionally in rt61pci_config_lna_gain() subroutine. Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=44361 Cc: stable@vger.kernel.org Reported-and-tested-by: <dolohow@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-06cfg80211: process pending events when unregistering net deviceDaniel Drake
libertas currently calls cfg80211_disconnected() when it is being brought down. This causes an event to be allocated, but since the wdev is already removed from the rdev by the time that the event processing work executes, the event is never processed or freed. http://article.gmane.org/gmane.linux.kernel.wireless.general/95666 Fix this leak, and other possible situations, by processing the event queue when a device is being unregistered. Thanks to Johannes Berg for the suggestion. Signed-off-by: Daniel Drake <dsd@laptop.org> Cc: stable@vger.kernel.org Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-08-06Bluetooth: Fix socket not getting freed if l2cap channel create failsJaganath Kanakkassery
If l2cap_chan_create() fails then it will return from l2cap_sock_kill since zapped flag of sk is reset. Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: smp: Fix possible NULL dereferenceAndrei Emeltchenko
smp_chan_create might return NULL so we need to check before dereferencing smp. Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: Set name_state to unknown when entry name is emptyRam Malovany
When the name of the given entry is empty , the state needs to be updated accordingly. Cc: stable@vger.kernel.org Signed-off-by: Ram Malovany <ramm@ti.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: Fix using a NULL inquiry cache entryRam Malovany
If the device was not found in a list of found devices names of which are pending.This may happen in a case when HCI Remote Name Request was sent as a part of incoming connection establishment procedure. Hence there is no need to continue resolving a next name as it will be done upon receiving another Remote Name Request Complete Event. This will fix a kernel crash when trying to use this entry to resolve the next name. Cc: stable@vger.kernel.org Signed-off-by: Ram Malovany <ramm@ti.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: Fix using NULL inquiry entryRam Malovany
If entry wasn't found in the hci_inquiry_cache_lookup_resolve do not resolve the name.This will fix a kernel crash when trying to use NULL pointer. Cc: stable@vger.kernel.org Signed-off-by: Ram Malovany <ramm@ti.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: Fix legacy pairing with some devicesSzymon Janc
Some devices e.g. some Android based phones don't do SDP search before pairing and cancel legacy pairing when ACL is disconnected. PIN Code Request event which changes ACL timeout to HCI_PAIRING_TIMEOUT is only received after remote user entered PIN. In that case no L2CAP is connected so default HCI_DISCONN_TIMEOUT (2 seconds) is being used to timeout ACL connection. This results in problems with legacy pairing as remote user has only few seconds to enter PIN before ACL is disconnected. Increase disconnect timeout for incomming connection to HCI_PAIRING_TIMEOUT if SSP is disabled and no linkey exists. To avoid keeping ACL alive for too long after SDP search set ACL timeout back to HCI_DISCONN_TIMEOUT when L2CAP is connected. 2012-07-19 13:24:43.413521 < HCI Command: Create Connection (0x01|0x0005) plen 13 bdaddr 00:02:72:D6:6A:3F ptype 0xcc18 rswitch 0x01 clkoffset 0x0000 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 2012-07-19 13:24:43.425224 > HCI Event: Command Status (0x0f) plen 4 Create Connection (0x01|0x0005) status 0x00 ncmd 1 2012-07-19 13:24:43.885222 > HCI Event: Role Change (0x12) plen 8 status 0x00 bdaddr 00:02:72:D6:6A:3F role 0x01 Role: Slave 2012-07-19 13:24:44.054221 > HCI Event: Connect Complete (0x03) plen 11 status 0x00 handle 42 bdaddr 00:02:72:D6:6A:3F type ACL encrypt 0x00 2012-07-19 13:24:44.054313 < HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2 handle 42 2012-07-19 13:24:44.055176 > HCI Event: Page Scan Repetition Mode Change (0x20) plen 7 bdaddr 00:02:72:D6:6A:3F mode 0 2012-07-19 13:24:44.056217 > HCI Event: Max Slots Change (0x1b) plen 3 handle 42 slots 5 2012-07-19 13:24:44.059218 > HCI Event: Command Status (0x0f) plen 4 Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 0 2012-07-19 13:24:44.062192 > HCI Event: Command Status (0x0f) plen 4 Unknown (0x00|0x0000) status 0x00 ncmd 1 2012-07-19 13:24:44.067219 > HCI Event: Read Remote Supported Features (0x0b) plen 11 status 0x00 handle 42 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 2012-07-19 13:24:44.067248 < HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3 handle 42 page 1 2012-07-19 13:24:44.071217 > HCI Event: Command Status (0x0f) plen 4 Read Remote Extended Features (0x01|0x001c) status 0x00 ncmd 1 2012-07-19 13:24:44.076218 > HCI Event: Read Remote Extended Features (0x23) plen 13 status 0x00 handle 42 page 1 max 1 Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00 2012-07-19 13:24:44.076249 < HCI Command: Remote Name Request (0x01|0x0019) plen 10 bdaddr 00:02:72:D6:6A:3F mode 2 clkoffset 0x0000 2012-07-19 13:24:44.081218 > HCI Event: Command Status (0x0f) plen 4 Remote Name Request (0x01|0x0019) status 0x00 ncmd 1 2012-07-19 13:24:44.105214 > HCI Event: Remote Name Req Complete (0x07) plen 255 status 0x00 bdaddr 00:02:72:D6:6A:3F name 'uw000951-0' 2012-07-19 13:24:44.105284 < HCI Command: Authentication Requested (0x01|0x0011) plen 2 handle 42 2012-07-19 13:24:44.111207 > HCI Event: Command Status (0x0f) plen 4 Authentication Requested (0x01|0x0011) status 0x00 ncmd 1 2012-07-19 13:24:44.112220 > HCI Event: Link Key Request (0x17) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.112249 < HCI Command: Link Key Request Negative Reply (0x01|0x000c) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.115215 > HCI Event: Command Complete (0x0e) plen 10 Link Key Request Negative Reply (0x01|0x000c) ncmd 1 status 0x00 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.116215 > HCI Event: PIN Code Request (0x16) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:48.099184 > HCI Event: Auth Complete (0x06) plen 3 status 0x13 handle 42 Error: Remote User Terminated Connection 2012-07-19 13:24:48.179182 > HCI Event: Disconn Complete (0x05) plen 4 status 0x00 handle 42 reason 0x13 Reason: Remote User Terminated Connection Cc: stable@vger.kernel.org Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: Fix possible deadlock in SCO codeGustavo Padovan
sco_chan_del() only has conn != NULL when called from sco_conn_del() so just move the code from it that deal with conn to sco_conn_del(). [ 120.765529] [ 120.765529] ====================================================== [ 120.766529] [ INFO: possible circular locking dependency detected ] [ 120.766529] 3.5.0-rc1-10292-g3701f94-dirty #70 Tainted: G W [ 120.766529] ------------------------------------------------------- [ 120.766529] kworker/u:3/1497 is trying to acquire lock: [ 120.766529] (&(&conn->lock)->rlock#2){+.+...}, at: [<ffffffffa00b7ecc>] sco_chan_del+0x4c/0x170 [bluetooth] [ 120.766529] [ 120.766529] but task is already holding lock: [ 120.766529] (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}, at: [<ffffffffa00b8401>] sco_conn_del+0x61/0xe0 [bluetooth] [ 120.766529] [ 120.766529] which lock already depends on the new lock. [ 120.766529] [ 120.766529] [ 120.766529] the existing dependency chain (in reverse order) is: [ 120.766529] [ 120.766529] -> #1 (slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}: [ 120.766529] [<ffffffff8107980e>] lock_acquire+0x8e/0xb0 [ 120.766529] [<ffffffff813c19e0>] _raw_spin_lock+0x40/0x80 [ 120.766529] [<ffffffffa00b85e9>] sco_connect_cfm+0x79/0x300 [bluetooth] [ 120.766529] [<ffffffffa0094b13>] hci_sync_conn_complete_evt.isra.90+0x343/0x400 [bluetooth] [ 120.766529] [<ffffffffa009d447>] hci_event_packet+0x317/0xfb0 [bluetooth] [ 120.766529] [<ffffffffa008aa68>] hci_rx_work+0x2c8/0x890 [bluetooth] [ 120.766529] [<ffffffff81047db7>] process_one_work+0x197/0x460 [ 120.766529] [<ffffffff810489d6>] worker_thread+0x126/0x2d0 [ 120.766529] [<ffffffff8104ee4d>] kthread+0x9d/0xb0 [ 120.766529] [<ffffffff813c4294>] kernel_thread_helper+0x4/0x10 [ 120.766529] [ 120.766529] -> #0 (&(&conn->lock)->rlock#2){+.+...}: [ 120.766529] [<ffffffff81078a8a>] __lock_acquire+0x154a/0x1d30 [ 120.766529] [<ffffffff8107980e>] lock_acquire+0x8e/0xb0 [ 120.766529] [<ffffffff813c19e0>] _raw_spin_lock+0x40/0x80 [ 120.766529] [<ffffffffa00b7ecc>] sco_chan_del+0x4c/0x170 [bluetooth] [ 120.766529] [<ffffffffa00b8414>] sco_conn_del+0x74/0xe0 [bluetooth] [ 120.766529] [<ffffffffa00b88a2>] sco_disconn_cfm+0x32/0x60 [bluetooth] [ 120.766529] [<ffffffffa0093a82>] hci_disconn_complete_evt.isra.53+0x242/0x390 [bluetooth] [ 120.766529] [<ffffffffa009d747>] hci_event_packet+0x617/0xfb0 [bluetooth] [ 120.766529] [<ffffffffa008aa68>] hci_rx_work+0x2c8/0x890 [bluetooth] [ 120.766529] [<ffffffff81047db7>] process_one_work+0x197/0x460 [ 120.766529] [<ffffffff810489d6>] worker_thread+0x126/0x2d0 [ 120.766529] [<ffffffff8104ee4d>] kthread+0x9d/0xb0 [ 120.766529] [<ffffffff813c4294>] kernel_thread_helper+0x4/0x10 [ 120.766529] [ 120.766529] other info that might help us debug this: [ 120.766529] [ 120.766529] Possible unsafe locking scenario: [ 120.766529] [ 120.766529] CPU0 CPU1 [ 120.766529] ---- ---- [ 120.766529] lock(slock-AF_BLUETOOTH-BTPROTO_SCO); [ 120.766529] lock(&(&conn->lock)->rlock#2); [ 120.766529] lock(slock-AF_BLUETOOTH-BTPROTO_SCO); [ 120.766529] lock(&(&conn->lock)->rlock#2); [ 120.766529] [ 120.766529] *** DEADLOCK *** Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06Bluetooth: btusb: Add vendor specific ID (0a5c:21f4) BCM20702A0Manoj Iyer
Patch adds support for BCM20702A0 device id (0a5c:21f4). usb-devices after patch was applied: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=21f4 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=E4D53DF154D6 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) usb-devices before patch was applied: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0a5c ProdID=21f4 Rev=01.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=E4D53DF154D6 C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none) I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none) Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Tested-by: Chris Gagnon <chris.gagnon@canonical.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06ARM: integrator: use clk_prepare_enable() for timerLinus Walleij
The Integrator timer is using the clock framework to get the timer frequency, but missed to prepare the clock before enabling. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-08-06Merge branch 'mxs/fixes-for-3.6' of ↵Arnd Bergmann
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes * 'mxs/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6: ARM: mxs: always build ocotp ARM: mxs: Remove MMAP_MIN_ADDR setting from mxs_defconfig ARM: mx28: Fix registers range ARM: mx23: Fix registers range
2012-08-06Merge branch 'imx/fixes-for-3.6' of ↵Arnd Bergmann
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes * 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6: ARM: dts: imx: fix gpio interrupts property ARM: dts: imx53-ard: add regulators for lan9220 ARM: imx: enable emi_slow_gate clock for imx5 ARM: imx6q-sabrelite: Setup CLKO IOMUX Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-08-06drm/i915: make rc6 in sysfs functions conditionalHunt Xu
Commit 0136db586c028f71e7cc21cc183064ff0d5919c8 merges rc6 information into the power group. However, when compiled with CONFIG_PM not set, modprobing i915 would taint since power_group_name is defined as NULL. This patch makes these rc6 in sysfs functions conditional upon the definition of the CONFIG_PM macro to avoid the above-mentioned problem. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45181 Cc: stable@vger.kernel.org Tested-by: Kris Karas <bugs-a12@moonlit-rail.com> Signed-off-by: Hunt Xu <mhuntxu@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-08-06iommu/amd: Fix ACS path checkingAlex Williamson
SR-IOV can create buses without a bridge. There may be other cases where this happens as well. In these cases skip to the parent bus and continue testing devices there. Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
2012-08-06iommu/intel: Fix ACS path checkingAlex Williamson
SR-IOV can create buses without a bridge. There may be other cases where this happens as well. In these cases skip to the parent bus and continue testing devices there. Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
2012-08-06iommu/amd: Fix pci_request_acs() call-placeJoerg Roedel
The pci_request_acs() function needs to be called before PCI probing to be effective. So move it to another call-place to ensure that. Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
2012-08-06MAINTAINERS: update entry for Linus WalleijLinus Walleij
I prefer to use the Linaro mail address for the MAINTAINERS entry due to heavy mail traffic. Take this opportunity to update the wildcards, including removing the stmpe* drivers from the ux500 entry since these are not specific to that machine. Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-08-06ALSA: hda - Fix regression of HDMI codec probingTakashi Iwai
The commit c4bfe94a causes a regression on some codecs at probing. Since this was just a workaround to shut up a kernel warning, it'd be better to revert and fix properly. So we ended up with re-adding the cleanup callback. Tested-and-reported-by: Matt Horan <matt@matthoran.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-08-06ALSA: hda - add dock support for Thinkpad T430sPhilipp A. Mohrenweiser
Add a model/fixup string "lenovo-dock", for Thinkpad T430s, to allow sound in docking station. Tested on Lenovo T430s with ThinkPad Mini Dock Plus Series 3 Cc: stable@kernel.org Signed-off-by: Philipp A. Mohrenweiser <phiamo@googlemail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2012-08-06drm/i915: Workaround hang with BSD and forcewake on SandyBridgeChris Wilson
For reasons that are not apparent to anybody, 990bbdadaba (drm/i915: Group the GT routines together in both code and vtable) breaks the use of the BitStream Decoder ring on SandyBridge. The active ingredient of that patch is the conversion from a udelay(10) to a udelay(1) in the busy-wait loop of waiting for the forcewake acknowledge. If we restore that udelay(10) or insert another udelay(1) afterwards (or any wait longer than 250ns) everything works again. An alternative is also to remove any delay from the busy-wait loop. Given that in the atomic sections we want to complete the wait as quick as possible to avoid blocking the CPU for too long, it makes sense to remove the delay altogether and simply spin on the exit condition until it completes. So we replace the udelay(1) with cpu_relax(). Papers over regression from commit 990bbdadabaa51828e475eda86ee5720a4910cc3 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Mon Jul 2 11:51:02 2012 -0300 drm/i915: Group the GT routines together in both code and vtable Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51738 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-08-06drm/i915: Make intel_panel_get_backlight static.Stéphane Marchesin
This function isn't used outside of intel_panel.c, so make it static. Signed-off-by: Stéphane Marchesin <marcheu@chromium.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-08-05i915: don't map imported dma-bufs for dmar.Dave Airlie
The exporter should have given us pages in the correct place, avoid the prepare object mapping phase on dmar systems. This fixes an oops on a GM45/R600 machine, when running the intel/radeon tests. Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-08-05drm/i915: remove unused variableDevendra Naga
the following warning was produced, drivers/gpu/drm/i915/i915_gem_context.c: In function ‘i915_switch_context’: drivers/gpu/drm/i915/i915_gem_context.c:454:6: warning: unused variable ‘ret’ [-Wunused-variable] fix up by removing it Signed-off-by: Devendra Naga <devendra.aaru@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-08-05drm/i915: Don't forget to apply SNB PIPE_CONTROL GTT workaround.Eric Anholt
If a buffer that was the target of a PIPE_CONTROL from userland was a reused one that hadn't been evicted which had not previously had this workaround applied, then the early return for a correct presumed_offset in this function meant we would not bind it into the GTT and the write would land somewhere else. Fixes reproducible failures with GL_EXT_timer_query usage in apitrace, and I also expect it to fix the intermittent OQ issues on snb that danvet's been working on. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48019 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=52932 Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Carl Worth <cworth@cworth.org> Tested-by: Carl Worth <cworth@cworth.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-08-05Merge branches 'timers-urgent-for-linus' and 'perf-urgent-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timers and perf fixes from Ingo Molnar: "Timers: - Fix another timekeeping bug Pef: - Make clean brace expansion fix for some shells, from Palmer Cox - Warn user just once per guest kernel when not finding kernel info, from David Ahern - perf test fix from Jiri Olsa - Fix error handling on event creation in perf top, from David Ahern - Fix check on perf_target__strnerror, from Namhyung Kim - Save the whole cmdline, from David Ahern There's this infrastructure change: - Prep work for the DWARF CFI post unwinder, so that it doesn't use perf_session in lots of places, just evlist/evsel is enough. which is a late infrastructure change that prepare for future feature work - we wanted it upstream to simplify the fixes/development patch flows." * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: time: Fix adjustment cleanup bug in timekeeping_adjust() * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf tools: Remove brace expansion from clean target perf kvm top: Limit guest kernel info message to once perf tools: Introduce intlist perf tools: Change strlist to use the new rblist perf tools: Introducing rblist perf kvm: Use strtol for walking guestmount directory perf tool: Save cmdline from user in file header vs what is passed to record perf top: Error handling for counter creation should parallel perf-record perf session: Remove no longer used synthesize_sample method perf evsel: Adopt parse_sample method from perf_event perf evlist: Introduce perf_evlist__parse_sample perf session: Use perf_evlist__id_hdr_size more extensively perf session: Use perf_evlist__sample_id_all more extensively perf session: Use perf_evlist__sample_type more extensively perf evsel: Precalculate the sample size perf target: Fix check on buffer size perf symbols: Fix array sizes for binary types arrays perf test: Fix parse events automated tests
2012-08-05Merge tag 'perf-core-for-mingo' of ↵Ingo Molnar
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent Pull perf/core fixes and some late updates from Arnaldo Carvalho de Melo: * Make clean brace expansion fix for some shells, from Palmer Cox * Warn user just once per guest kernel when not finding kernel info, from David Ahern * perf test fix from Jiri Olsa * Fix error handling on event creation in perf top, from David Ahern * Fix check on perf_target__strnerror, from Namhyung Kim * Save the whole cmdline, from David Ahern * Prep work for the DWARF CFI post unwinder, so that it doesn't uses perf_session in lots of places, just evlist/evsel is enough. Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
generated by cgit (git 2.34.1) at 2025-09-11 18:32:21 +0000