| Age | Commit message (Collapse) | Author |
|---|
|
When boost is set for CPUs using acpi-cpufreq, the policy is not
updated which can cause boost to be incorrectly not reported.
Fixes: 218a06a79d9a ("cpufreq: Support per-policy performance boost")
Link: https://patch.msgid.link/20240626204723.6237-2-mario.limonciello@amd.com
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Suggested-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The behavior introduced in commit f37a4d6b4a2c ("cpufreq: Fix per-policy
boost behavior on SoCs using cpufreq_boost_set_sw()") sets up the boost
policy incorrectly when boost has been enabled by the platform firmware
initially even if a driver sets the policy up.
This is because policy_has_boost_freq() assumes that there is a frequency
table set up by the driver and that the boost frequencies are advertised
in that table. This assumption doesn't work for acpi-cpufreq or
amd-pstate. Only use this check to enable boost if it's not already
enabled instead of also disabling it if alreayd enabled.
Fixes: f37a4d6b4a2c ("cpufreq: Fix per-policy boost behavior on SoCs using cpufreq_boost_set_sw()")
Link: https://patch.msgid.link/20240626204723.6237-1-mario.limonciello@amd.com
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Suggested-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
reclaim
There is a potential parallel list adding for retrying in
btrfs_reclaim_bgs_work and adding to the unused list. Since the block
group is removed from the reclaim list and it is on a relocation work,
it can be added into the unused list in parallel. When that happens,
adding it to the reclaim list will corrupt the list head and trigger
list corruption like below.
Fix it by taking fs_info->unused_bgs_lock.
[177.504][T2585409] BTRFS error (device nullb1): error relocating ch= unk 2415919104
[177.514][T2585409] list_del corruption. next->prev should be ff1100= 0344b119c0, but was ff11000377e87c70. (next=3Dff110002390cd9c0)
[177.529][T2585409] ------------[ cut here ]------------
[177.537][T2585409] kernel BUG at lib/list_debug.c:65!
[177.545][T2585409] Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI
[177.555][T2585409] CPU: 9 PID: 2585409 Comm: kworker/u128:2 Tainted: G W 6.10.0-rc5-kts #1
[177.568][T2585409] Hardware name: Supermicro SYS-520P-WTR/X12SPW-TF, BIOS 1.2 02/14/2022
[177.579][T2585409] Workqueue: events_unbound btrfs_reclaim_bgs_work[btrfs]
[177.589][T2585409] RIP: 0010:__list_del_entry_valid_or_report.cold+0x70/0x72
[177.624][T2585409] RSP: 0018:ff11000377e87a70 EFLAGS: 00010286
[177.633][T2585409] RAX: 000000000000006d RBX: ff11000344b119c0 RCX:0000000000000000
[177.644][T2585409] RDX: 000000000000006d RSI: 0000000000000008 RDI:ffe21c006efd0f40
[177.655][T2585409] RBP: ff110002e0509f78 R08: 0000000000000001 R09:ffe21c006efd0f08
[177.665][T2585409] R10: ff11000377e87847 R11: 0000000000000000 R12:ff110002390cd9c0
[177.676][T2585409] R13: ff11000344b119c0 R14: ff110002e0508000 R15:dffffc0000000000
[177.687][T2585409] FS: 0000000000000000(0000) GS:ff11000fec880000(0000) knlGS:0000000000000000
[177.700][T2585409] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[177.709][T2585409] CR2: 00007f06bc7b1978 CR3: 0000001021e86005 CR4:0000000000771ef0
[177.720][T2585409] DR0: 0000000000000000 DR1: 0000000000000000 DR2:0000000000000000
[177.731][T2585409] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:0000000000000400
[177.742][T2585409] PKRU: 55555554
[177.748][T2585409] Call Trace:
[177.753][T2585409] <TASK>
[177.759][T2585409] ? __die_body.cold+0x19/0x27
[177.766][T2585409] ? die+0x2e/0x50
[177.772][T2585409] ? do_trap+0x1ea/0x2d0
[177.779][T2585409] ? __list_del_entry_valid_or_report.cold+0x70/0x72
[177.788][T2585409] ? do_error_trap+0xa3/0x160
[177.795][T2585409] ? __list_del_entry_valid_or_report.cold+0x70/0x72
[177.805][T2585409] ? handle_invalid_op+0x2c/0x40
[177.812][T2585409] ? __list_del_entry_valid_or_report.cold+0x70/0x72
[177.820][T2585409] ? exc_invalid_op+0x2d/0x40
[177.827][T2585409] ? asm_exc_invalid_op+0x1a/0x20
[177.834][T2585409] ? __list_del_entry_valid_or_report.cold+0x70/0x72
[177.843][T2585409] btrfs_delete_unused_bgs+0x3d9/0x14c0 [btrfs]
There is a similar retry_list code in btrfs_delete_unused_bgs(), but it is
safe, AFAICS. Since the block group was in the unused list, the used bytes
should be 0 when it was added to the unused list. Then, it checks
block_group->{used,reserved,pinned} are still 0 under the
block_group->lock. So, they should be still eligible for the unused list,
not the reclaim list.
The reason it is safe there it's because because we're holding
space_info->groups_sem in write mode.
That means no other task can allocate from the block group, so while we
are at deleted_unused_bgs() it's not possible for other tasks to
allocate and deallocate extents from the block group, so it can't be
added to the unused list or the reclaim list by anyone else.
The bug can be reproduced by btrfs/166 after a few rounds. In practice
this can be hit when relocation cannot find more chunk space and ends
with ENOSPC.
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Suggested-by: Johannes Thumshirn <Johannes.Thumshirn@wdc.com>
Fixes: 4eb4e85c4f81 ("btrfs: retry block group reclaim without infinite loop")
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Delete extra blank lines inside of test_selftest().
Signed-off-by: Zhu Jun <zhujun2@cmss.chinamobile.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240627031905.7133-1-zhujun2@cmss.chinamobile.com
|
|
We used bpf_prog_pack to aggregate bpf programs into huge page to
relieve the iTLB pressure on the system. We can apply it to bpf
trampoline, as Song had been implemented it in core and x86 [0]. This
patch is going to use bpf_prog_pack to RV64 bpf trampoline. Since Song
and Puranjay have done a lot of work for bpf_prog_pack on RV64,
implementing this function will be easy.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Björn Töpel <bjorn@rivosinc.com> #riscv
Link: https://lore.kernel.org/all/20231206224054.492250-1-song@kernel.org [0]
Link: https://lore.kernel.org/bpf/20240622030437.3973492-4-pulehui@huaweicloud.com
|
|
We get the size of the trampoline image during the dry run phase and
allocate memory based on that size. The allocated image will then be
populated with instructions during the real patch phase. But after
commit 26ef208c209a ("bpf: Use arch_bpf_trampoline_size"), the `im`
argument is inconsistent in the dry run and real patch phase. This may
cause emit_imm in RV64 to generate a different number of instructions
when generating the 'im' address, potentially causing out-of-bounds
issues. Let's emit the maximum number of instructions for the "im"
address during dry run to fix this problem.
Fixes: 26ef208c209a ("bpf: Use arch_bpf_trampoline_size")
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240622030437.3973492-3-pulehui@huaweicloud.com
|
|
For trampoline using bpf_prog_pack, we need to generate a rw_image
buffer with size of (image_end - image). For regular trampoline, we use
the precise image size generated by arch_bpf_trampoline_size to allocate
rw_image. But for struct_ops trampoline, we allocate rw_image directly
using close to PAGE_SIZE size. We do not need to allocate for that much,
as the patch size is usually much smaller than PAGE_SIZE. Let's use
precise image size for it too.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Björn Töpel <bjorn@rivosinc.com> #riscv
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20240622030437.3973492-2-pulehui@huaweicloud.com
|
|
Coverity points out that after calling btf__new_empty_split() the wrong
value is checked for error.
Fixes: 58e185a0dc35 ("libbpf: Add btf__distill_base() creating split BTF with distilled base BTF")
Reported-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240629100058.2866763-1-alan.maguire@oracle.com
|
|
Introduce e2e selftest for bpf_xdp_flow_lookup kfunc through
xdp_flowtable utility.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/b74393fb4539aecbbd5ac7883605f86a95fb0b6b.1719698275.git.lorenzo@kernel.org
|
|
Introduce bpf_xdp_flow_lookup kfunc in order to perform the lookup
of a given flowtable entry based on a fib tuple of incoming traffic.
bpf_xdp_flow_lookup can be used as building block to offload in xdp
the processing of sw flowtable when hw flowtable is not available.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/bpf/55d38a4e5856f6d1509d823ff4e98aaa6d356097.1719698275.git.lorenzo@kernel.org
|
|
This adds a small internal mapping table so that a new bpf (xdp) kfunc
can perform lookups in a flowtable.
As-is, xdp program has access to the device pointer, but no way to do a
lookup in a flowtable -- there is no way to obtain the needed struct
without questionable stunts.
This allows to obtain an nf_flowtable pointer given a net_device
structure.
In order to keep backward compatibility, the infrastructure allows the
user to add a given device to multiple flowtables, but it will always
return the first added mapping performing the lookup since it assumes
the right configuration is 1:1 mapping between flowtables and net_devices.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/bpf/9f20e2c36f494b3bf177328718367f636bb0b2ab.1719698275.git.lorenzo@kernel.org
|
|
Check that all fields of a V2 algorithm header fit into the available
firmware data buffer.
The wmfw V2 format introduced variable-length strings in the algorithm
block header. This means the overall header length is variable, and the
position of most fields varies depending on the length of the string
fields. Each field must be checked to ensure that it does not overflow
the firmware data buffer.
As this ia bugfix patch, the fixes avoid making any significant change to
the existing code. This makes it easier to review and less likely to
introduce new bugs.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e7673 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240627141432.93056-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the payload length check in cs_dsp_load() and cs_dsp_coeff_load()
to be done before the block is processed.
The check that the length of a block payload does not exceed the number
of remaining bytes in the firwmware file buffer was being done near the
end of the loop iteration. However, some code before that check used the
length field without validating it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e7673 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240627141432.93056-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Return an error from cs_dsp_power_up() if a block header is longer
than the amount of data left in the file.
The previous code in cs_dsp_load() and cs_dsp_load_coeff() would loop
while there was enough data left in the file for a valid region. This
protected against overrunning the end of the file data, but it didn't
abort the file processing with an error.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e7673 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240627141432.93056-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the checking that firmware file buffer is large enough for the
wmfw header, to prevent overrunning the buffer.
The original code tested that the firmware data buffer contained
enough bytes for the sums of the size of the structs
wmfw_header + wmfw_adsp1_sizes + wmfw_footer
But wmfw_adsp1_sizes is only used on ADSP1 firmware. For ADSP2 and
Halo Core the equivalent struct is wmfw_adsp2_sizes, which is
4 bytes longer. So the length check didn't guarantee that there
are enough bytes in the firmware buffer for a header with
wmfw_adsp2_sizes.
This patch splits the length check into three separate parts. Each
of the wmfw_header, wmfw_adsp?_sizes and wmfw_footer are checked
separately before they are used.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: f6bc909e7673 ("firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs")
Link: https://patch.msgid.link/20240627141432.93056-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
My earlier fix missed an incorrect function prototype that shows up on
native 32-bit builds:
In file included from fs/notify/fanotify/fanotify_user.c:14:
include/linux/syscalls.h:248:25: error: conflicting types for 'sys_fanotify_mark'; have 'long int(int, unsigned int, u32, u32, int, const char *)' {aka 'long int(int, unsigned int, unsigned int, unsigned int, int, const char *)'}
1924 | SYSCALL32_DEFINE6(fanotify_mark,
| ^~~~~~~~~~~~~~~~~
include/linux/syscalls.h:862:17: note: previous declaration of 'sys_fanotify_mark' with type 'long int(int, unsigned int, u64, int, const char *)' {aka 'long int(int, unsigned int, long long unsigned int, int, const char *)'}
On x86 and powerpc, the prototype is also wrong but hidden in an #ifdef,
so it never caused problems.
Add another alternative declaration that matches the conditional function
definition.
Fixes: 403f17a33073 ("parisc: use generic sys_fanotify_mark implementation")
Cc: stable@vger.kernel.org
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
syzbot reported a general protection fault caused by a null pointer
dereference in coalesce_fill_reply(). The issue occurs when req_base->dev
is null, leading to an invalid memory access.
This panic occurs if dumping coalesce when no device name is specified.
Fixes: f750dfe825b9 ("ethtool: provide customized dim profile management")
Reported-by: syzbot+e77327e34cdc8c36b7d3@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=e77327e34cdc8c36b7d3
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Apart from the regular dts fixes for wrong addresses, missing
or wrong properties, this reverts the previous move away from
cd-gpios to the mmc-controller's internal card-detect.
With this change applied, it was reported that boards could not
detect card anymore, so this go reverted of course.
* tag 'v6.10-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add sound-dai-cells for RK3368
arm64: dts: rockchip: Fix the i2c address of es8316 on Cool Pi 4B
arm64: dts: rockchip: fix PMIC interrupt pin on ROCK Pi E
arm64: dts: rockchip: make poweroff(8) work on Radxa ROCK 5A
Revert "arm64: dts: rockchip: remove redundant cd-gpios from rk3588 sdmmc nodes"
ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi node
arm64: dts: rockchip: Fix the value of `dlg,jack-det-rate` mismatch on rk3399-gru
arm64: dts: rockchip: set correct pwm0 pinctrl on rk3588-tiger
arm64: dts: rockchip: Rename LED related pinctrl nodes on rk3308-rock-pi-s
arm64: dts: rockchip: Fix SD NAND and eMMC init on rk3308-rock-pi-s
arm64: dts: rockchip: Fix rk3308 codec@ff560000 reset-names
arm64: dts: rockchip: Fix the DCDC_REG2 minimum voltage on Quartz64 Model B
Link: https://lore.kernel.org/r/10237789.nnTZe4vzsl@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
in rare cases, e.g. for injecting a machine check we do intercept all
load PSW instructions via ICTL_LPSW. With facility 193 a new variant
LPSWEY was added. KVM needs to handle that as well.
Fixes: a3efa8429266 ("KVM: s390: gen_facilities: allow facilities 165, 193, 194 and 196")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Message-ID: <20240628163547.2314-1-borntraeger@linux.ibm.com>
|
|
On the OMAPL138, the SPI reference clock is provided by the Power and
Sleep Controller (PSC). The PSC's datasheet says that 'some peripherals
have special programming requirements and additional recommended steps
you must take before you can invoke the PSC module state transition'. I
didn't find more details in documentation but it appears that PSC needs
the SPI to clear the POWERDOWN bit before disabling the clock. Indeed,
when this bit is set, the PSC gets stuck in transitions from enable to
disable state.
Clear the POWERDOWN bit when releasing driver's resources
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20240624071745.17409-1-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue into main
Tony nguyen says:
====================
Intel Wired LAN Driver Updates 2024-06-28 (MAINTAINERS, ice)
This series contains updates to MAINTAINERS file and ice driver.
Jesse replaces himself with Przemek in the maintainers file.
Karthik Sundaravel adds support for VF get/set MAC address via devlink.
Eric checks for errors from ice_vsi_rebuild() during queue
reconfiguration.
Paul adjusts FW API version check for E830 devices.
Piotr adds differentiation of unload type when shutting down AdminQ.
Przemek changes ice_adapter initialization to occur once per physical
card.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth into main
bluetooth pull request for net:
- Ignore too large handle values in BIG
- L2CAP: sync sock recv cb and release
- hci_bcm4377: Fix msgid release
- ISO: Check socket flag instead of hcon
- hci_event: Fix setting of unicast qos interval
- hci: disallow setting handle bigger than HCI_CONN_HANDLE_MAX
- Add quirk to ignore reserved PHY bits in LE Extended Adv Report
- hci_core: cancel all works upon hci_unregister_dev
- btintel_pcie: Fix REVERSE_INULL issue reported by coverity
- qca: Fix BT enable failure again for QCA6390 after warm reboot
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This accounts for the existence of two Steam Deck revisions
instead of a single revision
Signed-off-by: Matthew Schwartz <mattschwartz@gwu.edu>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240628205822.348402-3-mattschwartz@gwu.edu
|
|
Valve's Steam Deck Galileo revision has a 800x1280 OLED panel
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: John Schoenick <johns@valvesoftware.com>
Signed-off-by: Matthew Schwartz <mattschwartz@gwu.edu>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240628205822.348402-2-mattschwartz@gwu.edu
|
|
Michael Chan says:
====================
bnxt_en: PTP updates for net-next
The first 5 patches implement the PTP feature on the new BCM5760X
chips. The main new hardware feature is the new TX timestamp
completion which enables the driver to retrieve the TX timestamp
in NAPI without deferring to the PTP worker.
The last 5 patches increase the number of TX PTP packets in-flight
from 1 to 4 on the older BCM5750X chips. On these older chips, we
need to call firmware in the PTP worker to retrieve the timestamp.
We use an arry to keep track of the in-flight TX PTP packets.
v2: Patch #2: Fix the unwind of txr->is_ts_pkt when bnxt_start_xmit() aborts.
Patch #4: Set the SKBTX_IN_PROGRESS flag for timestamp packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we require the spinlock to protect ptp->txts_prod, change
ptp->tx_avail to non-atomic and protect it under the same spinlock.
Add a new helper function bnxt_ptp_get_txts_prod() to decrement
ptp->tx_avail under spinlock and return the producer.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Start accepting up to 4 TX TS requests on BCM5750X (P5) chips.
These PTP TX packets will be queued in the ptp->txts_req[] array
waiting for the TX timestamp to complete. The entries in the
array will be managed by a producer and consumer index. The
producer index is updated under spinlock since multiple TX rings
can try to send PTP packets at the same time.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the function bnxt_stamp_tx_skb() to return 0 for suceess
or -EAGAIN if the timestamp is still pending in firmware. The
calling PTP aux worker will reschedule based on the return code.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current 5750X PTP code paths, there is always at most one TX
SKB requested for timestamp and we won't accept another one until we
have retrieved the timestamp or it has timed out. Remove the
unnecessary check in bnxt_get_tx_ts_p5() for a pending SKB and change
the function to void.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the older 5750X (P5) chips, we currently support only 1 TX PTP
packet in-flight waiting for the timestamp. Refactor the
datastructures to prepare to support up to 4 TX PTP packets.
Combine all fields required for PTP TX timestamp query into one
structure. An array of this structure will be added in follow-on
patches to support multiple outstanding TX timestamps.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM5760X firmware will advertise direct 64-bit PHC registers access
for the driver from BAR0.
Make the necessary changes in handling HWRM_PORT_MAC_PTP_QCFG's
response and PHC register mapping for 5760X chips.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new BCM5760X chips will return the timestamp of TX packets in a
new completion. Add logic in __bnxt_poll_work() to handle this
completion type to retrieve the timestamp. This feature eliminates
the limit on the number of in-flight PTP TX packets.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver's current logic will always free all the TX SKBs up to
txr->tx_hw_cons within NAPI. In the next patches, we'll be adding
logic to handle TX timestamp completion and we may need to hold
some remaining TX SKBs if we don't have the timestamp completions
yet.
Modify __bnxt_poll_work_done() to clear each event bit separately to
allow bnapi->tx_int() to decide whether to clear BNXT_TX_CMP_EVENT or
not. bnapi->tx_int() will not clear BNXT_TX_CMP_EVENT if some TX
SKBs are held waiting for TX timestamps. Note that legacy chips will
never hold any SKBs this way. The SKB is always deferred to the PTP
worker slow path to retrieve the timestamp from firmware. On the new
P7 chips, the timestamp is returned by the hardware directly and we
can retrieve it directly from NAPI.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the unused is_gso field and add the is_ts_pkt field to struct
bnxt_sw_tx_bd. This field will mark the TX BD that has requested
HW TX timestamp. The field needs to be cleared if the timestamp packet
is later aborted. This field will be useful when processing the
new TX timestamp completion from the hardware in the next patches.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new BCM5760X chips will generate this new TX timestamp completion
when a TX packet's timestamp has been taken right before transmission.
The driver logic to retrieve the timestamp will be added in the next
few patches.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Octeontx2 hardware uses Near Data Cache(NDC) block to cache
contexts in it so that access to LLC/DRAM can be avoided.
It is recommended in HRM to sync the NDC contents before
releasing/resetting LF resources. Hence implement NDC_SYNC
mailbox and sync contexts during driver teardown.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call phylink_ethtool_ksettings_get() for get_link_ksettings method and
ethtool_op_get_link() for get_link method.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next into main
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
Patch #1 to #11 to shrink memory consumption for transaction objects:
struct nft_trans_chain { /* size: 120 (-32), cachelines: 2, members: 10 */
struct nft_trans_elem { /* size: 72 (-40), cachelines: 2, members: 4 */
struct nft_trans_flowtable { /* size: 80 (-48), cachelines: 2, members: 5 */
struct nft_trans_obj { /* size: 72 (-40), cachelines: 2, members: 4 */
struct nft_trans_rule { /* size: 80 (-32), cachelines: 2, members: 6 */
struct nft_trans_set { /* size: 96 (-24), cachelines: 2, members: 8 */
struct nft_trans_table { /* size: 56 (-40), cachelines: 1, members: 2 */
struct nft_trans_elem can now be allocated from kmalloc-96 instead of
kmalloc-128 slab.
Series from Florian Westphal. For the record, I have mangled patch #1
to add nft_trans_container_*() and use if for every transaction object.
I have also added BUILD_BUG_ON to ensure struct nft_trans always comes
at the beginning of the container transaction object. And few minor
cleanups, any new bugs are of my own.
Patch #12 simplify check for SCTP GSO in IPVS, from Ismael Luceno.
Patch #13 nf_conncount key length remains in the u32 bound, from Yunjian Wang.
Patch #14 removes unnecessary check for CTA_TIMEOUT_L3PROTO when setting
default conntrack timeouts via nfnetlink_cttimeout API, from
Lin Ma.
Patch #15 updates NFT_SECMARK_CTX_MAXLEN to 4096, SELinux could use
larger secctx names than the existing 256 bytes length.
Patch #16 adds a selftest to exercise nfnetlink_queue listeners leaving
nfnetlink_queue, from Florian Westphal.
Patch #17 increases hitcount from 255 to 65535 in xt_recent, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
tcp_metrics: add netlink protocol spec in YAML
Add a netlink protocol spec for the tcp_metrics generic netlink family.
First patch adjusts the uAPI header guards to make it easier to build
tools/ with non-system headers.
v1: https://lore.kernel.org/all/20240626201133.2572487-1-kuba@kernel.org
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a protocol spec for tcp_metrics, so that it's accessible via YNL.
Useful at the very least for testing fixes.
In this episode of "10,000 ways to complicate netlink" the metric
nest has defines which are off by 1. iproute2 does:
struct rtattr *m[TCP_METRIC_MAX + 1 + 1];
parse_rtattr_nested(m, TCP_METRIC_MAX + 1, a);
for (i = 0; i < TCP_METRIC_MAX + 1; i++) {
// ...
attr = m[i + 1];
This is too weird to support in YNL, add a new set of defines
with _correct_ values to the official kernel header.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_metrics' header lacks the customary _UAPI in the header guard.
This makes YNL build rules work less seamlessly.
We can easily fix that on YNL side, but this could also be
problematic if we ever needed to create a kernel-only tcp_metrics.h.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I don't see anything checking that TCP_METRICS_ATTR_SADDR_IPV4
is at least 4 bytes long, and the policy doesn't have an entry
for this attribute at all (neither does it for IPv6 but v6 is
manually validated).
Reviewed-by: Eric Dumazet <edumazet@google.com>
Fixes: 3e7013ddf55a ("tcp: metrics: Allow selective get/del of tcp-metrics based on src IP")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek RTL8211F Ethernet PHY supports 3 LED pins which are used to
indicate link status and activity. Add minimal LED controller driver
supporting the most common uses with the 'netdev' trigger.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For MTL+ platforms we use PICA chips for Type-C support and
hence mg programming is not needed.
Fixes issue with drm warn of TC port not being in legacy mode.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625111840.597574-1-mika.kahola@intel.com
(cherry picked from commit aaf9dc86bd806458f848c39057d59e5aa652a399)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Explicitly set the 'family' driver_info struct member for leafimx.
Previously, the correct operation relied on KVASER_LEAF being the first
defined value in enum kvaser_usb_leaf_family.
Fixes: e6c80e601053 ("can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20240628194529.312968-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fixes from Niklas Cassel:
- Add NOLPM quirk for for all Crucial BX SSD1 models.
Considering that we now have had bug reports for 3 different BX SSD1
variants from Crucial with the same product name, make the quirk more
inclusive, to catch more device models from the same generation.
- Fix a trivial NULL pointer dereference in the error path for
ata_host_release().
- Create a ata_port_free(), so that we don't miss freeing ata_port
struct members when freeing a struct ata_port.
- Fix a trivial double free in the error path for ata_host_alloc().
- Ensure that we remove the libata "remapped NVMe device count" sysfs
entry on .probe() error.
* tag 'ata-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: ahci: Clean up sysfs file on error
ata: libata-core: Fix double free on error
ata,scsi: libata-core: Do not leak memory for ata_port struct members
ata: libata-core: Fix null pointer dereference on error
ata: libata-core: Add ATA_HORKAGE_NOLPM for all Crucial BX SSD1 models
|
|
.probe() (ahci_init_one()) calls sysfs_add_file_to_group(), however,
if probe() fails after this call, we currently never call
sysfs_remove_file_from_group().
(The sysfs_remove_file_from_group() call in .remove() (ahci_remove_one())
does not help, as .remove() is not called on .probe() error.)
Thus, if probe() fails after the sysfs_add_file_to_group() call, the next
time we insmod the module we will get:
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:04.0/remapped_nvme'
CPU: 11 PID: 954 Comm: modprobe Not tainted 6.10.0-rc5 #43
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
sysfs_warn_dup.cold+0x17/0x23
sysfs_add_file_mode_ns+0x11a/0x130
sysfs_add_file_to_group+0x7e/0xc0
ahci_init_one+0x31f/0xd40 [ahci]
Fixes: 894fba7f434a ("ata: ahci: Add sysfs attribute to show remapped NVMe device count")
Cc: stable@vger.kernel.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240629124210.181537-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
If e.g. the ata_port_alloc() call in ata_host_alloc() fails, we will jump
to the err_out label, which will call devres_release_group().
devres_release_group() will trigger a call to ata_host_release().
ata_host_release() calls kfree(host), so executing the kfree(host) in
ata_host_alloc() will lead to a double free:
kernel BUG at mm/slub.c:553!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 11 PID: 599 Comm: (udev-worker) Not tainted 6.10.0-rc5 #47
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014
RIP: 0010:kfree+0x2cf/0x2f0
Code: 5d 41 5e 41 5f 5d e9 80 d6 ff ff 4d 89 f1 41 b8 01 00 00 00 48 89 d9 48 89 da
RSP: 0018:ffffc90000f377f0 EFLAGS: 00010246
RAX: ffff888112b1f2c0 RBX: ffff888112b1f2c0 RCX: ffff888112b1f320
RDX: 000000000000400b RSI: ffffffffc02c9de5 RDI: ffff888112b1f2c0
RBP: ffffc90000f37830 R08: 0000000000000000 R09: 0000000000000000
R10: ffffc90000f37610 R11: 617461203a736b6e R12: ffffea00044ac780
R13: ffff888100046400 R14: ffffffffc02c9de5 R15: 0000000000000006
FS: 00007f2f1cabe980(0000) GS:ffff88813b380000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2f1c3acf75 CR3: 0000000111724000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
<TASK>
? __die_body.cold+0x19/0x27
? die+0x2e/0x50
? do_trap+0xca/0x110
? do_error_trap+0x6a/0x90
? kfree+0x2cf/0x2f0
? exc_invalid_op+0x50/0x70
? kfree+0x2cf/0x2f0
? asm_exc_invalid_op+0x1a/0x20
? ata_host_alloc+0xf5/0x120 [libata]
? ata_host_alloc+0xf5/0x120 [libata]
? kfree+0x2cf/0x2f0
ata_host_alloc+0xf5/0x120 [libata]
ata_host_alloc_pinfo+0x14/0xa0 [libata]
ahci_init_one+0x6c9/0xd20 [ahci]
Ensure that we will not call kfree(host) twice, by performing the kfree()
only if the devres_open_group() call failed.
Fixes: dafd6c496381 ("libata: ensure host is free'd on error exit paths")
Cc: stable@vger.kernel.org
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20240629124210.181537-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
libsas is currently not freeing all the struct ata_port struct members,
e.g. ncq_sense_buf for a driver supporting Command Duration Limits (CDL).
Add a function, ata_port_free(), that is used to free a ata_port,
including its struct members. It makes sense to keep the code related to
freeing a ata_port in its own function, which will also free all the
struct members of struct ata_port.
Fixes: 18bd7718b5c4 ("scsi: ata: libata: Handle completion of CDL commands using policy 0xD")
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240629124210.181537-8-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
