| Age | Commit message (Collapse) | Author |
|---|
|
Some devices may need the clocks running, even while paused.
Add support for this use case.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-5-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
So far, the formatters have been reset/enabled using the .prepare()
callback. This was done in this callback because walking the formatters use
a mutex. A mutex is used because formatter handling require dealing
possibly slow clock operation.
With the support of non-atomic, .trigger() callback may be used which also
allows to properly enable and disable formatters on start but also
pause/resume.
This solve a random shift on TDMIN as well repeated samples on for TDMOUT.
Fixes: d60e4f1e4be5 ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-4-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Non atomic operations need to be performed in the trigger callback
of the TDM interfaces. Those are BEs but what matters is the nonatomic
flag of the FE in the DPCM context. Just set nonatomic for everything so,
at least, what is done is clear.
Fixes: 7864a79f37b5 ("ASoC: meson: add axg sound card support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With the AXG audio subsystem, there is a possible random channel shift on
TDM capture, when the slot number per lane is more than 2, and there is
more than one lane used.
The problem has been there since the introduction of the axg audio support
but such scenario is pretty uncommon. This is why there is no loud
complains about the problem.
Solving the problem require to make the links non-atomic and use the
trigger() callback to start FEs and BEs in the appropriate order.
This was tried in the past and reverted because it caused the block irq to
sleep while atomic. However, instead of reverting, the solution is to call
snd_pcm_period_elapsed() in a non atomic context.
Use the bottom half of a threaded IRQ to do so.
Fixes: 6dc4fa179fb8 ("ASoC: meson: add axg fifo base driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240426152946.3078805-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes the following Coccinelle/coccicheck warning reported by
string_choices.cocci:
opportunity for str_plural(zorro_num_autocon)
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20240412215704.204403-4-thorsten.blum@toblux.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The via-macii ADB driver calls request_irq() after disabling hard
interrupts. But disabling interrupts isn't necessary here because the
VIA shift register interrupt was masked during VIA1 initialization.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/419fcc09d0e563b425c419053d02236b044d86b0.1710298421.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
We can use the DEFINE_RES_MEM_NAMED() macro and resource_contains()
helper instead of reimplementing them in the code. No functional change
intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230831121623.36293-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm64 DeviceTree updates for v6.10
Support for Sony Xperia 1V, on the SM8550 platform, is added.
On IPQ8074, UART6 is described and unused gpios from QPIC are removed.
Backlight and touchscreen are described on Samsung Grand Prime devices.
RGB LED is added to Sony Xperia "Yoshino" devices, on which the
volume-up key definition is corrected as well.
Light Pulse Generator node is added to PM6150L PMIC, and blocks related
to USB Type-C on PM6150 are added.
On QCS6490 Rb3Gen2 UFS storage, USB Type-C management, a couple of
remoteprocs and both USB Type-C and native DisplayPort are enabled.
For the related IDP display is enabled, and the PMIC volume and power
buttons are described.
The inline crypto engine is added for SC7280, and an additional turbo
frequency is added to the MDP.
USB Type-C port management is introduce for the QRB2210 RB1. WiFi
firmware-name qualifier is added to both RB1 and RB2 boards.
The LMH node is added for the QCM2290, to configure the thresholds as
well as provide thermal pressure input.
The regulator range is adjusted for SD-card IO on SA8155P ADP, to allow
UHS modes.
The unused DCC is disabled on SC7180, and unused PMIC gpio block is
disabled on Trogdor.
For Lenovo Flex 5G, on SC8180X, the GPU firmware path is aligned with
agreed upon firmware structure. The frequency of the I2C bus for
touchpad is brought up to mitigate missing events. A number of
additional cleanups are introduced.
For SC8280XP GICv3 ITS is wired up for PCIe. EAS properties ad
introduced. A PS_HOLD-based restart node is introduced and acts as a
fallback if other mechanisms are unavailable to restart the board.
QFPROM is described, missing LMH interrupts for thermal pressure are
added. The TCSR download mode register is added, to allow configuring
if download mode should be entered on a crash.
USB Type-C handling is introduce for Fairphone FP3 as well.
On SM6350 crypto engine and DisplayPort controllers are introduced.
WiFi is enabled on the SM8150 Hardware Development Kit (HDK)
USB PD properties are added on Xiaomi Mi Pad 5 Pro devices.
Interconnect paths are added for UFS on SM8350, to ensure the bus is
voted for when the controller is operating.
On SM8550 the DMA coherency properties are corrected for SMMU and a few
consumers. Missing DWC3 quirks are added and the SNPS PHY parameters are
adjusted. Fastrpc banks are marked non-secure as needed.
The GPU description is introduced on SM8650, and enabled on the QRD. A
missing reserved-memory node is added, as is a few missing fastrpc
compute banks, and the non-secure-domain flag for other banks.
On X1 Elite SPMI support is added, together with PMIC definitons. The
link properties for DP3 are corrected, and audio-related resets are
introduced. SoundWire properties are corrected.
Nodes describing the PCIe bridge under the host controller is added
for a bunch of platforms.
The GPIO carrying orientation information for USB Type-C is added across
Fairphone 5, Lenovo Flex 5G, Lenovo Thinkpad X13s, SM8350 and SM845
HDKs.
A few dtbTool-specific compatibles for msm8916 is dropped from the
bindings.
A number of DeviceTree binding validation issues are corrected.
* tag 'qcom-arm64-for-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (110 commits)
dt-bindings: arm: qcom: Add Samsung Galaxy S5 China (kltechn)
arm64: dts: qcom: qrb4210-rb1: add firmware-name qualifier to WiFi node
arm64: dts: qcom: qrb2210-rb1: add firmware-name qualifier to WiFi node
arm64: dts: qcom: ipq6018: Add PCIe bridge node
arm64: dts: qcom: ipq8074: Add PCIe bridge node
arm64: dts: qcom: msm8996: Add PCIe bridge node
arm64: dts: qcom: sc8180x: Add PCIe bridge node
arm64: dts: qcom: qcs404: Add PCIe bridge node
arm64: dts: qcom: sc7280: Add PCIe bridge node
arm64: dts: qcom: msm8998: Add PCIe bridge node
arm64: dts: qcom: sc8280xp: Add PCIe bridge node
arm64: dts: qcom: sa8775p: Add PCIe bridge node
arm64: dts: qcom: sm8650: Add PCIe bridge node
arm64: dts: qcom: sm8550: Add PCIe bridge node
arm64: dts: qcom: sm8450: Add PCIe bridge node
arm64: dts: qcom: sm8350: Add PCIe bridge node
arm64: dts: qcom: sm8150: Add PCIe bridge node
arm64: dts: qcom: sdm845: Add PCIe bridge node
arm64: dts: qcom: sm8250: Add PCIe bridge node
arm64: dts: qcom: sdm845-db845c: make pcie0_3p3v_dual always-on
...
Link: https://lore.kernel.org/r/20240427175951.1439887-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/dt
Qualcomm Arm32 DeviceTree updates for v6.10
The QCA8074 PHY package found in IPQ4019 is properly described.
The Sony Xperia Z2 Tablet is cleaned up and improved, vibrator support
is added, upon support for Sony Xperia Z3 is added.
Also based on MSM8974, support for Samsung Galaxy S5 China is introduced.
The WiFi board type is added for these "klte" Samsung devices, to select
appropriate NVRAM firmware file.
Based on MSM8226, support for Motorola Moto G (2013) is added.
Nodes representing the PCIe bridges under existing controllers are added
for APQ8064, IPQ4019, IPQ8064, and SDX55.
A number of fixes throughout to improve compliance with DeviceTree
bindings.
* tag 'qcom-arm32-for-6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (22 commits)
ARM: dts: qcom: msm8974: Add DTS for Samsung Galaxy S5 China (kltechn)
ARM: dts: qcom: msm8974-klte-common: Pin WiFi board type
ARM: dts: qcom: msm8974: Split out common part of samsung-klte
ARM: dts: qcom: sdx55: Add PCIe bridge node
ARM: dts: qcom: apq8064: Add PCIe bridge node
ARM: dts: qcom: ipq4019: Add PCIe bridge node
ARM: dts: qcom: ipq8064: Add PCIe bridge node
ARM: dts: qcom: msm8974-sony-shinano: Enable vibrator
ARM: dts: qcom: ipq4019: add QCA8075 PHY Package nodes
ARM: dts: qcom: Add support for Motorola Moto G (2013)
dt-bindings: arm: qcom: Add Motorola Moto G (2013)
ARM: dts: qcom: msm8974: Add empty chosen node
ARM: dts: qcom: msm8974: Add @0 to memory node name
ARM: dts: qcom: Add Sony Xperia Z3 smartphone
ARM: dts: qcom: msm8974-sony-castor: Split into shinano-common
ARM: dts: qcom: msm8916: idle-state compatible require the generic idle-state
ARM: dts: qcom: include cpu in idle-state node names
ARM: dts: qcom: msm8974pro-castor: Rename wifi node name
ARM: dts: qcom: msm8974pro-castor: Add debounce-interval for keys
ARM: dts: qcom: msm8974pro-castor: Remove camera button definitions
...
Link: https://lore.kernel.org/r/20240427163625.1432458-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
- new boards: RG35XX 2024, RG35XX-Plus, RG35XX-H
* tag 'sunxi-dt-for-6.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h700: Add RG35XX-H DTS
arm64: dts: allwinner: h700: Add RG35XX-Plus DTS
arm64: dts: allwinner: h700: Add RG35XX 2024 DTS
dt-bindings: arm: sunxi: document Anbernic RG35XX handheld gaming device variants
Link: https://lore.kernel.org/r/20240427133006.GA146501@jernej-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
arm64: tegra: Changes for v6.10-rc1
Adds the Security Engine devices found on Tegra234 and fixes RTC aliases
by referencing them by label rather than path so that errors can be
detected more easily.
* tag 'tegra-for-6.10-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add Tegra Security Engine DT nodes
arm64: tegra: Correct Tegra132 I2C alias
Link: https://lore.kernel.org/r/20240426180519.3972626-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
ARM: tegra: Changes for v6.10-rc1
Adds support for EMC frequency scaling on PAZ100 devices with RAM code 1
and cleans up deprecated device tree properties.
* tag 'tegra-for-6.10-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: tegra20-ac97: Replace deprecated "gpio" suffix
ARM: tegra: paz00: Add emc-tables for ram-code 1
Link: https://lore.kernel.org/r/20240426180519.3972626-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/dt
dt-bindings: Changes for v6.10-rc1
Included is one change that adds the dma-coherent flag to the device
tree json-schema for host1x on Tegra194 and Tegra234.
* tag 'tegra-for-6.10-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: display: tegra: Allow dma-coherent on Tegra194 and later
Link: https://lore.kernel.org/r/20240426180519.3972626-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use the subreq_counter in netfs_io_request to allocate subrequest
debug_index values in read ops as well as write ops.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
|
|
Make the netfs_io_request::subreq_counter, used to generate values for
netfs_io_subrequest::debug_index, into an atomic_t so that it can be called
from the retry thread at the same time as the app thread issuing writes.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
|
|
Remove the deprecated use of PG_private_2 in netfslib.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
cc: Matthew Wilcox (Oracle) <willy@infradead.org>
cc: linux-cachefs@redhat.com
cc: linux-fsdevel@vger.kernel.org
cc: linux-mm@kvack.org
|
|
Remove the PG_fscache alias for PG_private_2 and use the latter directly.
Use of this flag for marking pages undergoing writing to the cache should
be considered deprecated and the folios should be marked dirty instead and
the write done in ->writepages().
Note that PG_private_2 itself should be considered deprecated and up for
future removal by the MM folks too.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
cc: Matthew Wilcox (Oracle) <willy@infradead.org>
cc: Ilya Dryomov <idryomov@gmail.com>
cc: Xiubo Li <xiubli@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
cc: Shyam Prasad N <sprasad@microsoft.com>
cc: Tom Talpey <tom@talpey.com>
cc: Bharath SM <bharathsm@microsoft.com>
cc: Trond Myklebust <trond.myklebust@hammerspace.com>
cc: Anna Schumaker <anna@kernel.org>
cc: netfs@lists.linux.dev
cc: ceph-devel@vger.kernel.org
cc: linux-cifs@vger.kernel.org
cc: linux-nfs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
cc: linux-mm@kvack.org
|
|
When dirty data is being written to the cache, setting/waiting on/clearing
the fscache flag is always done in tandem with setting/waiting on/clearing
the writeback flag. The netfslib buffered write routines wait on and set
both flags and the write request cleanup clears both flags, so the fscache
flag is almost superfluous.
The reason it isn't superfluous is because the fscache flag is also used to
indicate that data just read from the server is being written to the cache.
The flag is used to prevent a race involving overlapping direct-I/O writes
to the cache.
Change this to indicate that a page is in need of being copied to the cache
by placing a magic value in folio->private and marking the folios dirty.
Then when the writeback code sees a folio marked in this way, it only
writes it to the cache and not to the server.
If a folio that has this magic value set is modified, the value is just
replaced and the folio will then be uplodaded too.
With this, PG_fscache is no longer required by the netfslib core, 9p and
afs.
Ceph and nfs, however, still need to use the old PG_fscache-based tracking.
To deal with this, a flag, NETFS_ICTX_USE_PGPRIV2, now has to be set on the
flags in the netfs_inode struct for those filesystems. This reenables the
use of PG_fscache in that inode. 9p and afs use the netfslib write helpers
so get switched over; cifs, for the moment, does page-by-page manual access
to the cache, so doesn't use PG_fscache and is unaffected.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
cc: Matthew Wilcox (Oracle) <willy@infradead.org>
cc: Eric Van Hensbergen <ericvh@kernel.org>
cc: Latchesar Ionkov <lucho@ionkov.net>
cc: Dominique Martinet <asmadeus@codewreck.org>
cc: Christian Schoenebeck <linux_oss@crudebyte.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Ilya Dryomov <idryomov@gmail.com>
cc: Xiubo Li <xiubli@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
cc: Shyam Prasad N <sprasad@microsoft.com>
cc: Tom Talpey <tom@talpey.com>
cc: Bharath SM <bharathsm@microsoft.com>
cc: Trond Myklebust <trond.myklebust@hammerspace.com>
cc: Anna Schumaker <anna@kernel.org>
cc: netfs@lists.linux.dev
cc: v9fs@lists.linux.dev
cc: linux-afs@lists.infradead.org
cc: ceph-devel@vger.kernel.org
cc: linux-cifs@vger.kernel.org
cc: linux-nfs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
cc: linux-mm@kvack.org
|
|
Update i_blocks when i_size is updated when we finish making a write to the
pagecache to reflect the amount of space we think will be consumed.
This maintains cifs commit dbfdff402d89854126658376cbcb08363194d3cd ("smb3:
update allocation size more accurately on write completion") which would
otherwise be removed by the cifs part of the netfs writeback rewrite.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
cc: linux-mm@kvack.org
|
|
If traceprobe_parse_probe_arg_body() failed to allocate 'parg->fmt',
it jumps to the label 'out' instead of 'fail' by mistake.In the result,
the buffer 'tmp' is not freed in this case and leaks its memory.
Thus jump to the label 'fail' in that error case.
Link: https://lore.kernel.org/all/20240427072347.1421053-1-lumingyindetect@126.com/
Fixes: 032330abd08b ("tracing/probes: Cleanup probe argument parser")
Signed-off-by: LuMingYin <lumingyindetect@126.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
We found below OOB crash:
[ 33.452494] ==================================================================
[ 33.453513] BUG: KASAN: stack-out-of-bounds in refresh_cpu_vm_stats.constprop.0+0xcc/0x2ec
[ 33.454660] Write of size 164 at addr c1d03d30 by task swapper/0/0
[ 33.455515]
[ 33.455767] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 6.1.25-mainline #1
[ 33.456880] Hardware name: Generic DT based system
[ 33.457555] unwind_backtrace from show_stack+0x18/0x1c
[ 33.458326] show_stack from dump_stack_lvl+0x40/0x4c
[ 33.459072] dump_stack_lvl from print_report+0x158/0x4a4
[ 33.459863] print_report from kasan_report+0x9c/0x148
[ 33.460616] kasan_report from kasan_check_range+0x94/0x1a0
[ 33.461424] kasan_check_range from memset+0x20/0x3c
[ 33.462157] memset from refresh_cpu_vm_stats.constprop.0+0xcc/0x2ec
[ 33.463064] refresh_cpu_vm_stats.constprop.0 from tick_nohz_idle_stop_tick+0x180/0x53c
[ 33.464181] tick_nohz_idle_stop_tick from do_idle+0x264/0x354
[ 33.465029] do_idle from cpu_startup_entry+0x20/0x24
[ 33.465769] cpu_startup_entry from rest_init+0xf0/0xf4
[ 33.466528] rest_init from arch_post_acpi_subsys_init+0x0/0x18
[ 33.467397]
[ 33.467644] The buggy address belongs to stack of task swapper/0/0
[ 33.468493] and is located at offset 112 in frame:
[ 33.469172] refresh_cpu_vm_stats.constprop.0+0x0/0x2ec
[ 33.469917]
[ 33.470165] This frame has 2 objects:
[ 33.470696] [32, 76) 'global_zone_diff'
[ 33.470729] [112, 276) 'global_node_diff'
[ 33.471294]
[ 33.472095] The buggy address belongs to the physical page:
[ 33.472862] page:3cd72da8 refcount:1 mapcount:0 mapping:00000000 index:0x0 pfn:0x41d03
[ 33.473944] flags: 0x1000(reserved|zone=0)
[ 33.474565] raw: 00001000 ed741470 ed741470 00000000 00000000 00000000 ffffffff 00000001
[ 33.475656] raw: 00000000
[ 33.476050] page dumped because: kasan: bad access detected
[ 33.476816]
[ 33.477061] Memory state around the buggy address:
[ 33.477732] c1d03c00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 33.478630] c1d03c80: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 00
[ 33.479526] >c1d03d00: 00 04 f2 f2 f2 f2 00 00 00 00 00 00 f1 f1 f1 f1
[ 33.480415] ^
[ 33.481195] c1d03d80: 00 00 00 00 00 00 00 00 00 00 04 f3 f3 f3 f3 f3
[ 33.482088] c1d03e00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
[ 33.482978] ==================================================================
We find the root cause of this OOB is that arm does not clear stale stack
poison in the case of cpuidle.
This patch refer to arch/arm64/kernel/sleep.S to resolve this issue.
From cited commit [1] that explain the problem
Functions which the compiler has instrumented for KASAN place poison on
the stack shadow upon entry and remove this poison prior to returning.
In the case of cpuidle, CPUs exit the kernel a number of levels deep in
C code. Any instrumented functions on this critical path will leave
portions of the stack shadow poisoned.
If CPUs lose context and return to the kernel via a cold path, we
restore a prior context saved in __cpu_suspend_enter are forgotten, and
we never remove the poison they placed in the stack shadow area by
functions calls between this and the actual exit of the kernel.
Thus, (depending on stackframe layout) subsequent calls to instrumented
functions may hit this stale poison, resulting in (spurious) KASAN
splats to the console.
To avoid this, clear any stale poison from the idle thread for a CPU
prior to bringing a CPU online.
From cited commit [2]
Extend to check for CONFIG_KASAN_STACK
[1] commit 0d97e6d8024c ("arm64: kasan: clear stale stack poison")
[2] commit d56a9ef84bd0 ("kasan, arm64: unpoison stack only with CONFIG_KASAN_STACK")
Signed-off-by: Boy Wu <boy.wu@mediatek.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 5615f69bc209 ("ARM: 9016/2: Initialize the mapping of KASan shadow memory")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
- added multicolor LED node for pinephone
- marked pinephone LEDs to retain status in suspend
- DT cleanups & fixes
- fixed A64 GPU frequency at 432 MHz
- added H616 NMI node
- new boards: PocketBook 614 Plus, Tanix TX1
* tag 'sunxi-dt-for-6.10-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: h616: Add NMI device node
arm64: dts: allwinner: Add Tanix TX1 support
dt-bindings: arm: sunxi: document Tanix TX1 name
ARM: dts: sun5i: Add PocketBook 614 Plus support
dt-bindings: arm: sunxi: Add PocketBook 614 Plus
arm64: dts: allwinner: h616: Fix I2C0 pins
arm64: dts: allwinner: a64: Run GPU at 432 MHz
arm: dts: allwinner: drop underscore in node names
arm64: dts: allwinner: Orange Pi: delete node by phandle
arm64: dts: allwinner: drop underscore in node names
arm64: dts: allwinner: Pine H64: correctly remove reg_gmac_3v3
arm64: dts: allwinner: pinephone: add multicolor LED node
arm64: dts: allwinner: pinephone: Retain LEDs state in suspend
Link: https://lore.kernel.org/r/20240426164510.GA101219@jernej-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.10 (take two)
- Add external interrupt (IRQC) support for the RZ/Five SoC,
- Add SPI (MSIOF), external interrupt (INTC-EX), and IOMMU support for
the R-Car V4M SoC,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a779h0: Link IOMMU consumers
arm64: dts: renesas: r8a779h0: Add IPMMU nodes
arm64: dts: renesas: r8a779h0: Add INTC-EX node
arm64: dts: renesas: r8a779h0: Add MSIOF nodes
arm64: dts: renesas: rzg3s-smarc-som: Enable eMMC by default
riscv: dts: renesas: rzfive-smarc-som: Drop deleting interrupt properties from ETH0/1 nodes
arm64: dts: renesas: r9a07g043: Move interrupt-parent property to common DTSI
riscv: dts: renesas: r9a07g043f: Add IRQC node to RZ/Five SoC DTSI
arm64: dts: renesas: s4sk: Fix ethernet0 alias
Link: https://lore.kernel.org/r/cover.1714116737.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Guillaume Nault says:
====================
vxlan: Fix vxlan counters.
Like most virtual devices, vxlan needs special care when updating its
netdevice counters. This is done in patch 1. Patch 2 just adds a
missing VNI counter update (found while working on patch 1).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VXLAN stores per-VNI statistics using vxlan_vnifilter_count().
These statistics were not updated when arp_reduce() failed its
pskb_may_pull() call.
Use vxlan_vnifilter_count() to update the VNI counter when that
happens.
Fixes: 4095e0e1328a ("drivers: vxlan: vnifilter: per vni stats")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VXLAN devices update their stats locklessly. Therefore these counters
should either be stored in per-cpu data structures or the updates
should be done using atomic increments.
Since the net_device_core_stats infrastructure is already used in
vxlan_rcv(), use it for the other rx_dropped and tx_dropped counter
updates. Update the other counters atomically using DEV_STATS_INC().
Fixes: d342894c5d2f ("vxlan: virtual extensible lan")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the PTP programmable gpios to implement also PTP_PF_EXTTS
function. The pins can be configured to capture both of rising
and falling edge. Once the event is seen, then an interrupt is
generated and the LTC is saved in the registers.
On lan8814 only GPIO 3 can be configured for this.
This was tested using:
ts2phc -m -l 7 -s generic -f ts2phc.cfg
Where the configuration was the following:
---
[global]
ts2phc.pin_index 3
[eth0]
---
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Luiz Angelo Daros de Luca says:
====================
net: dsa: realtek: fix LED support for rtl8366
This series fixes the LED support for rtl8366. The existing code was not
tested in a device with switch LEDs and it was using a flawed logic.
The driver now keeps the default LED configuration if nothing requests a
different behavior. This may be enough for most devices. This can be
achieved either by omitting the LED from the device-tree or configuring
all LEDs in a group with the default state set to "keep".
The hardware trigger for LEDs in Realtek switches is shared among all
LEDs in a group. This behavior doesn't align well with the Linux LED
API, which controls LEDs individually. Once the OS changes the
brightness of a LED in a group still triggered by the hardware, the
entire group switches to software-controlled LEDs, even for those not
metioned in the device-tree. This shared behavior also prevents
offloading the trigger to the hardware as it would require an
orchestration between LEDs in a group, not currently present in the LED
API.
The assertion of device hardware reset during driver removal was removed
because it was causing an issue with the LED release code. Devres
devices are released after the driver's removal is executed. Asserting
the reset at that point was causing timeout errors during LED release
when it attempted to turn off the LED.
To: Linus Walleij <linus.walleij@linaro.org>
To: Alvin Šipraga <alsi@bang-olufsen.dk>
To: Andrew Lunn <andrew@lunn.ch>
To: Florian Fainelli <f.fainelli@gmail.com>
To: Vladimir Oltean <olteanv@gmail.com>
To: David S. Miller <davem@davemloft.net>
To: Eric Dumazet <edumazet@google.com>
To: Jakub Kicinski <kuba@kernel.org>
To: Paolo Abeni <pabeni@redhat.com>
To: Rob Herring <robh+dt@kernel.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
To: Conor Dooley <conor+dt@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Changes in v2:
- Fixed commit message formatting
- Added GROUP to LED group enum values. With that, moved the code that
disables LED into a new function to keep 80-collumn limit.
- Dropped unused enable argument in rb8366rb_get_port_led()
- Fixed variable order in rtl8366rb_setup_led()
- Removed redundant led group test in rb8366rb_{g,s}et_port_led()
- Initialize ret as 0 in rtl8366rb_setup_leds()
- Updated comments related to LED blinking and setup
- Link to v1: https://lore.kernel.org/r/20240310-realtek-led-v1-0-4d9813ce938e@gmail.com
Changes in v1:
- Rebased on new relatek DSA drivers
- Improved commit messages
- Added commit to remove the reset assert during .remove
- Link to RFC: https://lore.kernel.org/r/20240106184651.3665-1-luizluca@gmail.com
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit introduces LED drivers for rtl8366rb, enabling LEDs to be
described in the device tree using the same format as qca8k. Each port
can configure up to 4 LEDs.
If all LEDs in a group use the default state "keep", they will use the
default behavior after a reset. Changing the brightness of one LED,
either manually or by a trigger, will disable the default hardware
trigger and switch the entire LED group to manually controlled LEDs.
Once in this mode, there is no way to revert to hardware-controlled LEDs
(except by resetting the switch).
Software triggers function as expected with manually controlled LEDs.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The necessity of asserting the reset on removal was previously
questioned, as DSA's own cleanup methods should suffice to prevent
traffic leakage[1].
When a driver has subdrivers controlled by devres, they will be
unregistered after the main driver's .remove is executed. If it asserts
a reset, the subdrivers will be unable to communicate with the hardware
during their cleanup. For LEDs, this means that they will fail to turn
off, resulting in a timeout error.
[1] https://lore.kernel.org/r/20240123215606.26716-9-luizluca@gmail.com/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch family supports four LEDs for each of its six ports. Each
LED group is composed of one of these four LEDs from all six ports. LED
groups can be configured to display hardware information, such as link
activity, or manually controlled through a bitmap in registers
RTL8366RB_LED_0_1_CTRL_REG and RTL8366RB_LED_2_3_CTRL_REG.
After a reset, the default LED group configuration for groups 0 to 3
indicates, respectively, link activity, link at 1000M, 100M, and 10M, or
RTL8366RB_LED_CTRL_REG as 0x5432. These configurations are commonly used
for LED indications. However, the driver was replacing that
configuration to use manually controlled LEDs (RTL8366RB_LED_FORCE)
without providing a way for the OS to control them. The default
configuration is deemed more useful than fixed, uncontrollable turned-on
LEDs.
The driver was enabling/disabling LEDs during port_enable/disable.
However, these events occur when the port is administratively controlled
(up or down) and are not related to link presence. Additionally, when a
port N was disabled, the driver was turning off all LEDs for group N,
not only the corresponding LED for port N in any of those 4 groups. In
such cases, if port 0 was brought down, the LEDs for all ports in LED
group 0 would be turned off. As another side effect, the driver was
wrongly warning that port 5 didn't have an LED ("no LED for port 5").
Since showing the administrative state of ports is not an orthodox way
to use LEDs, it was not worth it to fix it and all this code was
dropped.
The code to disable LEDs was simplified only changing each LED group to
the RTL8366RB_LED_OFF state. Registers RTL8366RB_LED_0_1_CTRL_REG and
RTL8366RB_LED_2_3_CTRL_REG are only used when the corresponding LED
group is configured with RTL8366RB_LED_FORCE and they don't need to be
cleaned. The code still references an LED controlled by
RTL8366RB_INTERRUPT_CONTROL_REG, but as of now, no test device has
actually used it. Also, some magic numbers were replaced by macros.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of (struct rt6_info *)dst casts, we can use :
#define dst_rt6_info(_ptr) \
container_of_const(_ptr, struct rt6_info, dst)
Some places needed missing const qualifiers :
ip6_confirm_neigh(), ipv6_anycast_destination(),
ipv6_unicast_destination(), has_gateway()
v2: added missing parts (David Ahern)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch simply add SND_PCI_QUIRK for HP Laptop 15-da3001TU to fixed
mute led of laptop.
Signed-off-by: Aman Dhoot <amandhoot12@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CAMTp=B+3NG65Z684xMwHqdXDJhY+DJK-kuSw4adn6xwnG+b5JA@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When the host page size was more than 4 times larger than the FW page
size, this macro evaluated to zero resulting in zero-sized arrays.
Use DIV_ROUND_UP() to ensure the correct behavior.
Reported-by: 20240228012313.5934-1-yaolu@kylinos.cn
Closes: https://lore.kernel.org/dri-devel/20240228012313.5934-1-yaolu@kylinos.cn
Link: https://lore.kernel.org/dri-devel/20240228012313.5934-1-yaolu@kylinos.cn
Fixes: 927f3e0253c1 ("drm/imagination: Implement MIPS firmware processor and MMU support")
Cc: stable@vger.kernel.org
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
|
|
Add Grand Ridge (ATOM_CRESTMONT) to hpm_cpu_ids, so that MSR 0x54 can be
used.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240422212222.3881606-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Convert the incoming page to a folio and use it throughout, saving
several calls to compound_head(). Also use 'pos' for file position
rather than the ambiguous 'offset' and convert 'length' to type size_t
in case we get some truly ridiculous sized folios in the future. This
function should now be large-folio safe, but I may have missed
something.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
New boards: ArmSom Sige7, GameForce Chi,Forlinx FET3588-C with OK3588-C
baseboard, Protonic MECSBC, Wolfvision PF5.
The panthor driver for Mali Valhall GPUs landed, so a number of boards
enable their gpu (Cool Pi, Theobroma-Systems boards, QuartzPro64,
Rock5b, EVB1)
Also the USBDP phy driver landed, allowing the usb3 dual-role controllers
to be used on EVB1, Rock 5A and 5B, Indiedroid-Nova, Theobroma-Systems
Tiger and Jaguar.
A lot new peripherals for the Khadas Edge 2 (rtc, uart, sfc, adc, ir,
usb, pcie, tf-card, pmic); PCIe3 support on Jaguar, audio support for
the rk3308 and cache descriptions for rk356x and rk3328.
Corrected model names for boards from Radxa, Pine64, Powkiddy, Anberic
and general more dt cleanups.
* tag 'v6.10-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (64 commits)
arm64: dts: rockchip: add dual-role usb3 hosts to rk3588 Tiger-Haikou
arm64: dts: rockchip: add usb-id extcon on rk3588 tiger
arm64: dts: rockchip: fix comment for upper usb3 port
arm64: dts: rockchip: fix pcie-refclk frequency on rk3588 tiger
arm64: dts: rockchip: correct gpio_pwrctrl1 typos on rk3588(s) boards
arm64: dts: rockchip: Correct the model names for Pine64 boards
dt-bindings: arm: rockchip: Correct the descriptions for Pine64 boards
arm64: dts: rockchip: Add ArmSom Sige7 board
dt-bindings: arm: rockchip: Add ArmSoM Sige7
dt-bindings: vendor-prefixes: add ArmSoM
arm64: dts: rockchip: add PCIe3 support on rk3588-jaguar
arm64: dts: rockchip: move uart2 pinmux to dtsi on rk3588-tiger
arm64: dts: rockchip: Add USB-C Support for rk3588s-indiedroid-nova
arm64: dts: rockchip: correct the model name for Radxa ROCK 3A
dt-bindings: arm: rockchip: correct the model name for Radxa ROCK 3A
arm64: dts: rockchip: Correct the model names for Radxa ROCK 5 boards
dt-bindings: arm: rockchip: Correct the descriptions for Radxa boards
arm64: dts: rockchip: add lower USB3 port to rock-5b
arm64: dts: rockchip: add upper USB3 port to rock-5a
arm64: dts: rockchip: add USB3 to rk3588-evb1
...
Link: https://lore.kernel.org/r/15361932.O9o76ZdvQC@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Function gfs2_freeze_unlock() is always called with &sdp->sd_freeze_gh
as its argument, so clean up the code by passing in sdp instead.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
This patch elaborates on the use of PC by expanding the PC acronym,
explaining the units, and the relative position to which the offset
applies.
Signed-off-by: Dave Thaler <dthaler1968@googlemail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Vernet <void@manifault.com>
Link: https://lore.kernel.org/bpf/20240426231126.5130-1-dthaler1968@gmail.com
|
|
Petr Machata says:
====================
mlxsw: Improve events processing performance
Amit Cohen writes:
Spectrum ASICs only support a single interrupt, it means that all the
events are handled by one IRQ (interrupt request) handler.
Currently, we schedule a tasklet to handle events in EQ, then we also use
tasklet for CQ, SDQ and RDQ. Tasklet runs in softIRQ (software IRQ)
context, and will be run on the same CPU which scheduled it. It means that
today we have one CPU which handles all the packets (both network packets
and EMADs) from hardware.
The existing implementation is not efficient and can be improved.
Measuring latency of EMADs in the driver (without the time in FW) shows
that latency is increased by factor of 28 (x28) when network traffic is
handled by the driver.
Measuring throughput in CPU shows that CPU can handle ~35% less packets
of specific flow when corrupted packets are also handled by the driver.
There are cases that these values even worse, we measure decrease of ~44%
packet rate.
This can be improved if network packet and EMADs will be handled in
parallel by several CPUs, and more than that, if different types of traffic
will be handled in parallel. We can achieve this using NAPI.
This set converts the driver to process completions from hardware via NAPI.
The idea is to add NAPI instance per CQ (which is mapped 1:1 to SDQ/RDQ),
which means that each DQ can be handled separately. we have DQ for EMADs
and DQs for each trap group (like LLDP, BGP, L3 drops, etc..). See more
details in commit messages.
An additional improvement which is done as part of this set is related to
doorbells' ring. The idea is to handle small chunks of Rx packets (which
is also recommended using NAPI) and ring doorbells once per chunk. This
reduces the access to hardware which is expensive (time wise) and might
take time because of memory barriers.
With this set we can see better performance.
To summerize:
EMADs latency:
+------------------------------------------------------------------------+
| | Before this set | Now |
|------------------|---------------------------|-------------------------|
| Increased factor | x28 | x1.5 |
+------------------------------------------------------------------------+
Note that we can see even measurements that show better latency when
traffic is handled by the driver.
Throughput:
+------------------------------------------------------------------------+
| | Before this set | Now |
|-------------|----------------------------|-----------------------------|
| Reduced | 35% | 6% |
| packet rate | | |
+------------------------------------------------------------------------+
Additional improvements are planned - use page pool for buffer allocations
and avoid cache miss of each SKB using napi_build_skb().
Patch set overview:
Patches #1-#2 improve access to hardware by reducing dorbells' rings
Patch #3-#4 are preaparations for NAPI usage
Patch #5 converts the driver to use NAPI
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum ASICs only support a single interrupt, that means that all the
events are handled by one IRQ (interrupt request) handler. Once an
interrupt is received, we schedule tasklet to handle events from EQ and
then schedule tasklets to handle completions from CQs. Tasklet runs in
softIRQ (software IRQ) context, and will be run on the same CPU which
scheduled it. That means that today we use only one CPU to handle all the
packets (both network packets and EMADs) from hardware.
This can be improved using NAPI. The idea is to use NAPI instance per
CQ, which is mapped 1:1 to DQ (RDQ or SDQ). NAPI poll method can be run
in kernel thread, so then the driver will be able to handle WQEs in several
CPUs. Convert the existing code to use NAPI APIs.
Add NAPI instance as part of 'struct mlxsw_pci_queue' and initialize it
as part of CQs initialization. Set the appropriate poll method and dummy
net device, according to queue number, similar to tasklet setup. For CQs
which are used for completions of RDQ, use Rx poll method and
'napi_dev_rx', which is set as 'threaded'. It means that Rx poll method
will run in kernel context, so several RDQs will be handled in parallel.
For CQs which are used for completions of SDQ, use Tx poll method and
'napi_dev_tx', this method will run in softIRQ context, as it is
recommended in NAPI documentation, as Tx packets' processing is short task.
Convert mlxsw_pci_cq_{rx,tx}_tasklet() to poll methods. Handle 'budget'
argument - ignore it in Tx poll method, as it is recommended to not limit
Tx processing. For Rx processing, handle up to 'budget' completions.
Return 'work_done' which is the amount of completions that were handled.
Handle the following cases:
1. After processing 'budget' completions, the driver still has work to do:
Return work-done = budget. In that case, the NAPI instance will be
polled again (without the need to be rescheduled). Do not re-arm the
queue, as NAPI will handle the reschedule, so we do not have to involve
hardware to send an additional interrupt for the completions that should
be processed.
2. Event processing has been completed:
Call napi_complete_done() to mark NAPI processing as completed, which
means that the poll method will not be rescheduled. Re-arm the queue,
as all completions were handled.
In case that poll method handled exactly 'budget' completions, return
work-done = budget -1, to distinguish from the case that driver still
has completions to handle. Otherwise, return the amount of completions
that were handled.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch will set the driver to use NAPI for event processing. Then
tasklet mechanism will be used only for EQ. Reorganize 'mlxsw_pci_queue'
to hold EQ and CQ attributes in a union. For now, add tasklet for both EQ
and CQ. This will be changed in the next patch, as 'tasklet_struct' will be
replaced with NAPI instance.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlxsw will use NAPI for event processing in a next patch. As preparation,
add two dummy net devices and initialize them.
NAPI instance should be attached to net device. Usually each queue is used
by a single net device in network drivers, so the mapping between net
device to NAPI instance is intuitive. In our case, Rx queues are not per
port, they are per trap-group. Tx queues are mapped to net devices, but we
do not have a separate queue for each local port, several ports share the
same queue.
Use init_dummy_netdev() to initialize dummy net devices for NAPI.
To run NAPI poll method in a kernel thread, the net device which NAPI
instance is attached to should be marked as 'threaded'. It is
recommended to handle Tx packets in softIRQ context, as usually this is
a short task - just free the Tx packet which has been transmitted.
Rx packets handling is more complicated task, so drivers can use a
dedicated kernel thread to process them. It allows processing packets from
different Rx queues in parallel. We would like to handle only Rx packets in
kernel threads, which means that we will use two dummy net devices
(one for Rx and one for Tx). Set only one of them with 'threaded' as it
will be used for Rx processing. Do not fail in case that setting 'threaded'
fails, as it is better to use regular softIRQ NAPI rather than preventing
the driver from loading.
Note that the net devices are initialized with init_dummy_netdev(), so
they are not registered, which means that they will not be visible to user.
It will not be possible to change 'threaded' configuration from user
space, but it is reasonable in our case, as there is no another
configuration which makes sense, considering that user has no influence
on the usage of each queue.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, for each CQE in CQ, we ring CQ doorbell, then handle RDQ and
ring RDQ doorbell. Finally we ring CQ arm doorbell - once per CQ tasklet.
The idea of ringing CQ doorbell before RDQ doorbell, is to be sure that
when we post new WQE (after RDQ is handled), there is an available CQE.
This was done because of a hardware bug as part of
commit c9ebea04cb1b ("mlxsw: pci: Ring CQ's doorbell before RDQ's").
There is no real reason to ring RDQ and CQ doorbells for each completion,
it is better to handle several completions and reduce number of ringings,
as access to hardware is expensive (time wise) and might take time because
of memory barriers.
A previous patch changed CQ tasklet to handle up to 64 Rx packets. With
this limitation, we can ring CQ and RDQ doorbells once per CQ tasklet.
The counters of the doorbells are increased by the amount of packets
that we handled, then the device will know for which completion to send
an additional event.
To avoid reordering CQ and RDQ doorbells' ring, let the tasklet to ring
also RDQ doorbell, mlxsw_pci_cqe_rdq_handle() handles the counter but
does not ring the doorbell.
Note that with this change there is no need to copy the CQE, as we ring CQ
doorbell only after Rx packet processing (which uses the CQE) is done.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can get many completions in one interrupt. Currently, the CQ tasklet
handles up to half queue size completions, and then arms the hardware to
generate additional events, which means that in case that there were
additional completions that we did not handle, we will get immediately an
additional interrupt to handle the rest.
The decision to handle up to half of the queue size is arbitrary and was
determined in 2015, when mlxsw driver was added to the kernel. One
additional fact that should be taken into account is that while WQEs
from RDQ are handled, the CPU that handles the tasklet is dedicated for
this task, which means that we might hold the CPU for a long time.
Handle WQEs in smaller chucks, then arm CQ doorbell to notify the hardware
to send additional notifications. Set the chunk size to 64 as this number
is recommended using NAPI and the driver will use NAPI in a next patch.
Note that for now we use ARM doorbell to retrigger CQ tasklet, but with
NAPI it will be more efficient as software will reschedule the poll
method and we will not involve hardware for that.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1394 OHCI driver generates packet data for the response subaction to the
request subaction to some local registers. In the case, the driver should
assign timestamp to them by itself.
This commit fulfills the timestamp for the subaction.
Cc: stable@vger.kernel.org
Fixes: dcadfd7f7c74 ("firewire: core: use union for callback of transaction completion")
Link: https://lore.kernel.org/r/20240429084709.707473-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
packet contents
Ensure that packet_buffer_get respects the user_length provided. If
the length of the head packet exceeds the user_length, packet_buffer_get
will now return 0 to signify to the user that no data were read
and a larger buffer size is required. Helps prevent user space overflows.
Signed-off-by: Thanassis Avgerinos <thanassis.avgerinos@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
Handle cases where the RMP table placement in the BIOS is not 2M aligned
and the kexec-ed kernel could try to allocate from within that chunk
which then causes a fatal RMP fault.
The kexec failure is illustrated below:
SEV-SNP: RMP table physical range [0x0000007ffe800000 - 0x000000807f0fffff]
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
...
BIOS-e820: [mem 0x0000004080000000-0x0000007ffe7fffff] usable
BIOS-e820: [mem 0x0000007ffe800000-0x000000807f0fffff] reserved
BIOS-e820: [mem 0x000000807f100000-0x000000807f1fefff] usable
As seen here in the e820 memory map, the end range of the RMP table is not
aligned to 2MB and not reserved but it is usable as RAM.
Subsequently, kexec -s (KEXEC_FILE_LOAD syscall) loads it's purgatory
code and boot_param, command line and other setup data into this RAM
region as seen in the kexec logs below, which leads to fatal RMP fault
during kexec boot.
Loaded purgatory at 0x807f1fa000
Loaded boot_param, command line and misc at 0x807f1f8000 bufsz=0x1350 memsz=0x2000
Loaded 64bit kernel at 0x7ffae00000 bufsz=0xd06200 memsz=0x3894000
Loaded initrd at 0x7ff6c89000 bufsz=0x4176014 memsz=0x4176014
E820 memmap:
0000000000000000-000000000008efff (1)
000000000008f000-000000000008ffff (4)
0000000000090000-000000000009ffff (1)
...
0000004080000000-0000007ffe7fffff (1)
0000007ffe800000-000000807f0fffff (2)
000000807f100000-000000807f1fefff (1)
000000807f1ff000-000000807fffffff (2)
nr_segments = 4
segment[0]: buf=0x00000000e626d1a2 bufsz=0x4000 mem=0x807f1fa000 memsz=0x5000
segment[1]: buf=0x0000000029c67bd6 bufsz=0x1350 mem=0x807f1f8000 memsz=0x2000
segment[2]: buf=0x0000000045c60183 bufsz=0xd06200 mem=0x7ffae00000 memsz=0x3894000
segment[3]: buf=0x000000006e54f08d bufsz=0x4176014 mem=0x7ff6c89000 memsz=0x4177000
kexec_file_load: type:0, start:0x807f1fa150 head:0x1184d0002 flags:0x0
Check if RMP table start and end physical range in the e820 tables are
not aligned to 2MB and in that case map this range to reserved in all
the three e820 tables.
[ bp: Massage. ]
Fixes: c3b86e61b756 ("x86/cpufeatures: Enable/unmask SEV-SNP CPU feature")
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/df6e995ff88565262c2c7c69964883ff8aa6fc30.1714090302.git.ashish.kalra@amd.com
|
|
In __pci_register_driver(), the pci core overwrites the dev_groups field of
the embedded struct device_driver with the dev_groups from the outer
struct pci_driver unconditionally.
Set dev_groups in the pci_driver to make sure it is used.
This was broken since the introduction of pvpanic-pci.
Fixes: db3a4f0abefd ("misc/pvpanic: add PCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Fixes: ded13b9cfd59 ("PCI: Add support for dev_groups to struct pci_driver")
Link: https://lore.kernel.org/r/20240411-pvpanic-pci-dev-groups-v1-1-db8cb69f1b09@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new API helper e820__range_update_table() with which to update an
arbitrary e820 table. Move all current users of
e820__range_update_kexec() to this new helper.
[ bp: Massage. ]
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/b726af213ad55053f8a7a1e793b01bb3f1ca9dd5.1714090302.git.ashish.kalra@amd.com
|
