| Age | Commit message (Collapse) | Author |
|---|
|
RTS polarity of rs485-enabled ports is currently initialized on uart
open via:
tty_port_open()
tty_port_block_til_ready()
tty_port_raise_dtr_rts() # if (C_BAUD(tty))
uart_dtr_rts()
uart_port_dtr_rts()
There's at least three problems here:
First, if no baud rate is set, RTS polarity is not initialized.
That's the right thing to do for rs232, but not for rs485, which
requires that RTS is deasserted unconditionally.
Second, if the DeviceTree property "linux,rs485-enabled-at-boot-time" is
present, RTS should be deasserted as early as possible, i.e. on probe.
Otherwise it may remain asserted until first open.
Third, even though RTS is deasserted on open and close, it may
subsequently be asserted by uart_throttle(), uart_unthrottle() or
uart_set_termios() because those functions aren't rs485-aware.
(Only uart_tiocmset() is.)
To address these issues, move RTS initialization from uart_port_dtr_rts()
to uart_configure_port(). Prevent subsequent modification of RTS
polarity by moving the existing rs485 check from uart_tiocmget() to
uart_update_mctrl().
That way, RTS is initialized on probe and then remains unmodified unless
the uart transmits data. If rs485 is enabled at runtime (instead of at
boot) through a TIOCSRS485 ioctl(), RTS is initialized by the uart
driver's ->rs485_config() callback and then likewise remains unmodified.
The PL011 driver initializes RTS on uart open and prevents subsequent
modification in its ->set_mctrl() callback. That code is obsoleted by
the present commit, so drop it.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2d2acaf3a69e89b7bf687c912022b11fd29dfa1e.1642909284.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 8d479237727c ("serial: amba-pl011: add RS485 support") sought to
keep RTS deasserted on set_mctrl if rs485 is enabled. However it did so
only if deasserted RTS polarity is high. Fix it in case it's low.
Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org # v5.15+
Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Jochen Mades <jochen@mades.net>
[lukas: copyedit commit message, add stable designation]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/85fa3323ba8c307943969b7343e23f34c3e652ba.1642909284.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
x_char is ignored by stm32_usart_start_tx() when xmit buffer is empty.
Fix start_tx condition to allow x_char to be sent.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When sending x_char in stm32_usart_transmit_chars(), driver can overwrite
the value of TDR register by the value of x_char. If this happens, the
previous value that was present in TDR register will not be sent through
uart.
This code checks if the previous value in TDR register is sent before
writing the x_char value into register.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cfb3 ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tty_port struct is part of the rpmsg_tty_port structure.
The issue is that the rpmsg_tty_port structure is freed on
rpmsg_tty_remove while it is still referenced in the tty_struct.
Its release is not predictable due to workqueues.
For instance following ftrace shows that rpmsg_tty_close is called after
rpmsg_tty_release_cport:
nr_test.sh-389 [000] ..... 212.093752: rpmsg_tty_remove <-rpmsg_dev_
remove
cat-1191 [001] ..... 212.095697: tty_release <-__fput
nr_test.sh-389 [000] ..... 212.099166: rpmsg_tty_release_cport <-rpm
sg_tty_remove
cat-1191 [001] ..... 212.115352: rpmsg_tty_close <-tty_release
cat-1191 [001] ..... 212.115371: release_tty <-tty_release_str
As consequence, the port must be free only when user has released the TTY
interface.
This path :
- Introduce the .destruct port tty ops function to release the allocated
rpmsg_tty_port structure.
- Introduce the .hangup tty ops function to call tty_port_hangup.
- Manages the tty port refcounting to trig the .destruct port ops,
- Introduces the rpmsg_tty_cleanup function to ensure that the TTY is
removed before decreasing the port refcount.
Fixes: 7c0408d80579 ("tty: add rpmsg driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20220104163545.34710-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a user API regression introduced with commit f76edd8f7ce0 ("tty:
cyclades, remove this orphan"), which removed a part of the API and
caused compilation errors for user programs using said part, such as
GCC 9 in its libsanitizer component[1]:
.../libsanitizer/sanitizer_common/sanitizer_platform_limits_posix.cc:160:10: fatal error: linux/cyclades.h: No such file or directory
160 | #include <linux/cyclades.h>
| ^~~~~~~~~~~~~~~~~~
compilation terminated.
make[4]: *** [Makefile:664: sanitizer_platform_limits_posix.lo] Error 1
As the absolute minimum required bring `struct cyclades_monitor' and
ioctl numbers back then so as to make the library build again. Add a
preprocessor warning as to the obsolescence of the features provided.
References:
[1] GCC PR sanitizer/100379, "cyclades.h is removed from linux kernel
header files", <https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100379>
Fixes: f76edd8f7ce0 ("tty: cyclades, remove this orphan")
Cc: stable@vger.kernel.org # v5.13+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Maciej W. Rozycki <macro@embecosm.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.20.2201260733430.11348@tpp.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564688493F7DD9B9C610827C45E9@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add power reset for bluetooth via enable-gpios in h5_btrtl_open function.
While testing the RTL8822CS SDIO WiFi/BT adapter, it was found that in
some cases the kernel could not initialize BT firmware. However,
manually resetting the adapter via gpio (off/on sequence) allows it to
start correctly.
Apparently, when the system starts, the adapter is in an undefined state
(including unknown gpio state after starting uboot). A forced reset helps
to initialize the adapter in most cases. It has been found experimentally
that 100 ms is sufficient for a reset.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add a variation of RTL8822CS with hci_ver = 0x08. This is fully similar
to RTL8822CS with hci_ver = 0x0a observed on the Tanix TX6 Android
set-top box and JetHome JetHub H1.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Rudi Heitbaum <rudi@heitbaum.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If blk_mq_request_issue_directly() failed from
blk_insert_cloned_request(), the request will be accounted start.
Currently, blk_insert_cloned_request() is only called by dm, and such
request won't be accounted done by dm.
In normal path, io will be accounted start from blk_mq_bio_to_request(),
when the request is allocated, and such io will be accounted done from
__blk_mq_end_request_acct() whether it succeeded or failed. Thus add
blk_account_io_done() to fix the problem.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220126012132.3111551-1-yukuai3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 5021d709b31b8a14317998a33cbc78be0de9ab30.
The patch is still a bit buggy, and this breaks some other hardware
types. It needs to be resubmitted in a non-buggy way, and make sure the
other hardware types also continue to work properly.
Fixes: 5021d709b31b ("tty: serial: Use fifo in 8250 console driver")
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/Ye/1+Z8mEzbKbrqG@linutronix.de
Link: https://lore.kernel.org/r/a1ac6254-f79e-d131-fa2a-c7ad714c6d4a@nvidia.com
Cc: Wander Lairson Costa <wander@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This check misses checking for platform_get_irq()'s call and may passes
the negative error codes to devm_request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling devm_request_irq() with invalid IRQ #s.
Fixes: 454fa271bc4e ("spi: Add Meson SPICC driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220126110447.24549-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
CDNSP driver read not initialized cdns->otg_v0_regs
which lead to segmentation fault. Patch fixes this issue.
Fixes: 2cf2581cd229 ("usb: cdns3: add power lost support for system resume")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220111090737.10345-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In uniphier_spi_remove(), there is a wrong code to get private data from
the platform device, so the driver can't be removed properly.
The driver should get spi_master from the platform device and retrieve
the private data from it.
Cc: <stable@vger.kernel.org>
Fixes: 5ba155a4d4cc ("spi: add SPI controller driver for UniPhier SoC")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1640148492-32178-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The corresponding API for clk_prepare is clk_unprepare, other than
clk_disable_unprepare.
Fix this by changing clk_disable_unprepare to clk_unprepare.
Fixes: 5762ab71eb24 ("spi: Add support for Armada 3700 SPI Controller")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20211206101931.2816597-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a build error observed with ARCH=arm DEFCONFIG=allmodconfig build.
drivers/usb/gadget/udc/at91_udc.h:174:42: error: format '%d' expects argument of type 'int', but argument 3 has type 'struct gpio_desc *' [-Werror=format=]
Fixes: 4a555f2b8d31 ("usb: gadget: at91_udc: Convert to GPIO descriptors")
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220119020849.25732-1-miles.chen@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code that looked up the USB3 PHY was ignoring all errors other than
EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and
simplify the code by using devm_phy_optional_get and dev_err_probe so
that a missing PHY is not treated as an error and unexpected errors
are handled properly.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.
Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Crashed at i.mx8qm platform when suspend if enable remote wakeup
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 244 Comm: kworker/u12:6 Not tainted 5.15.5-dirty #12
Hardware name: Freescale i.MX8QM MEK (DT)
Workqueue: events_unbound async_run_entry_fn
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : xhci_disable_hub_port_wake.isra.62+0x60/0xf8
lr : xhci_disable_hub_port_wake.isra.62+0x34/0xf8
sp : ffff80001394bbf0
x29: ffff80001394bbf0 x28: 0000000000000000 x27: ffff00081193b578
x26: ffff00081193b570 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00081193a29c x22: 0000000000020001 x21: 0000000000000001
x20: 0000000000000000 x19: ffff800014e90490 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000002 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000960 x9 : ffff80001394baa0
x8 : ffff0008145d1780 x7 : ffff0008f95b8e80 x6 : 000000001853b453
x5 : 0000000000000496 x4 : 0000000000000000 x3 : ffff00081193a29c
x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff000814591620
Call trace:
xhci_disable_hub_port_wake.isra.62+0x60/0xf8
xhci_suspend+0x58/0x510
xhci_plat_suspend+0x50/0x78
platform_pm_suspend+0x2c/0x78
dpm_run_callback.isra.25+0x50/0xe8
__device_suspend+0x108/0x3c0
The basic flow:
1. run time suspend call xhci_suspend, xhci parent devices gate the clock.
2. echo mem >/sys/power/state, system _device_suspend call xhci_suspend
3. xhci_suspend call xhci_disable_hub_port_wake, which access register,
but clock already gated by run time suspend.
This problem was hidden by power domain driver, which call run time resume before it.
But the below commit remove it and make this issue happen.
commit c1df456d0f06e ("PM: domains: Don't runtime resume devices at genpd_prepare()")
This patch call run time resume before suspend to make sure clock is on
before access register.
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Testeb-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220110172738.31686-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.
The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently when gadget enumerates in super speed plus, the isoc
endpoint request buffer size is not calculated correctly. Fix
this by checking the gadget speed against USB_SPEED_SUPER_PLUS
and update the request buffer size.
Fixes: 90c4d05780d4 ("usb: fix various gadgets null ptr deref on 10gbps cabling.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1642820602-20619-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.
The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.
Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Russell King says:
====================
net: stmmac/xpcs: modernise PCS support
This series updates xpcs and stmmac for the recent changes to phylink
to better support split PCS and to get rid of private MAC validation
functions.
This series is slightly more involved than other conversions as stmmac
has already had optional proper split PCS support.
The first six patches of this series were originally posted on 16th
December for CFT, and Wong Vee Khee reported his Intel Elkhart Lake
setup was fine the first six these. However, no tested-by was given.
The patches:
1) Provide a function to query the xpcs for the interface modes that
are supported.
2) Populates the MAC capabilities and switches stmmac_validate() to use
phylink_get_linkmodes(). We do not use phylink_generic_validate() yet
as (a) we do not always have the supported interfaces populated, and
(b) the existing code does not restrict based on interface. There
should be no functional effect from this patch.
3) Populates phylink's supported interfaces from the xpcs when the xpcs
is configured by firmware and also the firmware configured interface
mode. Note: this will restrict stmmac to only supporting these
interfaces modes - stmmac maintainers need to verify that this
behaviour is acceptable.
4) stmmac_validate() tail-calls xpcs_validate(), but we don't need it to
now that PCS have their own validation method. Convert stmmac and
xpcs to use this method instead.
5) xpcs sets the poll field of phylink_pcs to true, meaning xpcs
requires its status to be polled. There is no need to also set the
phylink_config.pcs_poll. Remove this.
6) Switch to phylink_generic_validate(). This is probably the most
contravertial change in this patch set as this will cause the MAC to
restrict link modes based on the interface mode. From an inspection
of the xpcs driver, this should be safe, as XPCS only further
restricts the link modes to a subset of these (whether that is
correct or not is not an issue I am addressing here.) For
implementations that do not use xpcs, this is a more open question
and needs feedback from stmmac maintainers.
7) Convert to use mac_select_pcs() rather than phylink_set_pcs() to set
the PCS - the intention is to eventually remove phylink_set_pcs()
once there are no more users of this.
v2: fix signoff and temporary warning in patch 4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert stmmac to use the mac_select_pcs() interface rather than using
phylink_set_pcs(). The intention here is to unify the approach for PCS
and eventually to remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert stmmac to use phylink_generic_validate() now that we have the
MAC capabilities and supported interfaces filled in, and we have the
PCS validation handled via the PCS operations.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Phylink will use PCS polling whenever the PCS's poll member is set, so
setting phylink_config.pcs_poll as well is redundant.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
stmmac explicitly calls the xpcs driver to validate the ethtool
linkmodes. This is no longer necessary as phylink now supports
validation through a PCS method. Convert both drivers to use this
new mechanism.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fill in phylink's supported_interfaces bitmap with the PHY interface
modes which can be used to talk to the PHY.
We indicate that the PHY interface mode passed in platform data is
always supported, as this is the initial mode passed into phylink.
When there is no PCS specified, we assume that this is the only mode
that is supported - indeed, the driver appears not to support dynamic
switching of interface types at present.
When a xpcs is present, it defines the PHY interface modes that the
stmmac driver can support. Request the supported interfaces from the
xpcs driver, and pass them to phylink.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the MAC speed, duplex and pause capabilities to the phylink_config
structure, and switch stmmac_validate() to use phylink_get_linkmodes()
to generate the mask of supported ethtool link modes.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function to the xpcs driver to retrieve the supported PHY
interface modes, which can be used by drivers to fill in phylink's
supported_interfaces mask.
We validate the interface bit index to ensure that it fits within the
bitmap as xpcs lists PHY_INTERFACE_MODE_MAX in an entry.
Tested-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> # Intel EHL Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
mlxsw: Add RJ45 ports support
We are in the process of qualifying a new system that has RJ45 ports as
opposed to the transceiver modules (e.g., SFP, QSFP) present on all
existing systems.
This patchset adds support for these ports in mlxsw by adding a couple of
missing BaseT link modes and rejecting ethtool operations that are
specific to transceiver modules.
Patchset overview:
Patches #1-#3 are cleanups and preparations.
Patch #4 adds support for two new link modes.
Patches #5-#6 query and cache the port module's type (e.g., QSFP, RJ45)
during initialization.
Patches #7-#9 forbid ethtool operations that are invalid on RJ45 ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Transceiver module reset through 'rst' field in PMAOS register is not
supported on RJ45 ports, so module reset should be rejected.
Therefore, before trying to access this field, validate the port module
type that was queried during initialization and return an error to user
space in case the port module type is RJ45 (twisted pair).
Output example:
# ethtool --reset swp11 phy
ETHTOOL_RESET 0x40
Cannot issue ETHTOOL_RESET: Invalid argument
$ dmesg
mlxsw_spectrum 0000:03:00.0 swp11: Reset module is not supported on port module type
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PMMP (Port Module Memory Map Properties) and MCION (Management Cable IO
and Notifications) registers are not supported on RJ45 ports, so setting
and getting power mode should be rejected.
Therefore, before trying to access those registers, validate the port
module type that was queried during initialization and return an error
to user space in case the port module type is RJ45 (twisted pair).
Set output example:
# ethtool --set-module swp1 power-mode-policy auto
netlink error: mlxsw_core: Power mode is not supported on port module type
netlink error: Invalid argument
Get output example:
$ ethtool --show-module swp11
netlink error: mlxsw_core: Power mode is not supported on port module type
netlink error: Invalid argument
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MCIA (Management Cable Info Access) register is not supported on RJ45
ports, so getting module EEPROM should be rejected.
Therefore, before trying to access this register, validate the port
module type that was queried during initialization and return an error
to user space in case the port module type is RJ45 (twisted pair).
Examples for output when trying to get EEPROM module:
Using netlink:
# ethtool -m swp1
netlink error: mlxsw_core: EEPROM is not equipped on port module type
netlink error: Invalid argument
Using IOCTL:
# ethtool -m swp1
Cannot get module EEPROM information: Invalid argument
$ dmesg
mlxsw_spectrum 0000:03:00.0 swp1: EEPROM is not equipped on port module type
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query and store port module's type during initialization so that it
could be later used to determine if certain configurations are allowed
based on the type.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Port Module Type Mapping (PMTP) register. It will be used by
subsequent patches to query port module types and forbid certain
configurations based on the port module's type.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of a process for supporting a new system with RJ45 connectors,
100BaseT and 1000BaseT link modes need to be supported.
Add support for these two link modes by adding the two corresponding
bits in PTYS (Port Type and Speed) register.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patches will forbid querying the port module's EEPROM info when
its type is RJ45 as in this case no transceiver module can ever be
connected to the port.
Add netdev argument to mlxsw_env_get_module_info() so it could be used
to print an error to the kernel log via netdev_err().
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of modules can be resolved from the first argument, so do not
pass it.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the 'err' variable and simply return.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent bug report outlined that the way GICv4.1 is handled across
kexec is pretty bad. We can end-up in a situation where ITSs share
memory (this is the case when SVPET==1) and reprogram the base
registers, creating a situation where ITSs that are part of a given
affinity group see different pointers. Which is illegal. Boo.
In order to restore some sanity, reset the BASERn registers to 0
*before* probing any ITS. Although this isn't optimised at all,
this is only a once-per-boot cost, which shouldn't show up on
anyone's radar.
Cc: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211216190315.GA14220@lpieralisi
Link: https://lore.kernel.org/r/20220124133809.1291195-1-maz@kernel.org
|
|
This reverts commit 9bb7b689274b67ecb3641e399e76f84adc627df1.
This caused a regression reported to Red Hat.
Fixes: 9bb7b689274b ("drm/ast: Support 1600x900 with 108MHz PCLK")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120040527.552068-1-airlied@gmail.com
|
|
Backmerging drm/drm-fixes into drm-misc-fixes for v5.17-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
The current implementation of HTB offload doesn't support some
parameters. Instead of ignoring them, actively return the EINVAL error
when they are set to non-defaults.
As this patch goes to stable, the driver API is not changed here. If
future drivers support more offload parameters, the checks can be moved
to the driver side.
Note that the buffer and cbuffer parameters are also not supported, but
the tc userspace tool assigns some default values derived from rate and
ceil, and identifying these defaults in sch_htb would be unreliable, so
they are still ignored.
Fixes: d03b195b5aa0 ("sch_htb: Hierarchical QoS hardware offload")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220125100654.424570-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit dee872e124e8 ("bpf: Populate kfunc BTF ID sets in struct btf")
breaks loading of some modules when CONFIG_DEBUG_INFO_BTF is not set.
register_btf_kfunc_id_set returns -ENOENT to the callers when
there is no module btf. Let's return 0 (success) instead to let
those modules work in !CONFIG_DEBUG_INFO_BTF cases.
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Fixes: dee872e124e8 ("bpf: Populate kfunc BTF ID sets in struct btf")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20220126001340.1573649-1-sdf@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Originally, the kernel strictly checked the size of the optval in
getsockopt(TCP_ZEROCOPY_RECEIVE) to be equal to sizeof(struct
tcp_zerocopy_receive). With c8856c0514549, this was changed to allow
optvals of different sizes.
The bpf code in the sockopt_sk test was still performing the strict size
check. This fix adapts the kernel behavior from c8856c0514549 in the
selftest, i.e., just check if the required fields are there.
Fixes: 9cacf81f81611 ("bpf: Remove extra lock_sock for TCP_ZEROCOPY_RECEIVE")
Signed-off-by: Felix Maurer <fmaurer@redhat.com>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/6f569cca2e45473f9a724d54d03fdfb45f29e35f.1643129402.git.fmaurer@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Andrii Nakryiko says:
====================
Another batch of simple deprecations. One of the last few, hopefully, as we
are getting close to deprecating all the planned APIs/features. See
individual patches for details.
v1->v2:
- rebased on latest bpf-next, fixed Closes: reference.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
