summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-05-31drm/amd/display: Refactor clk_mgr functionsEric Yang
[Why] Some HW specific implementations can be pulled out into clk_mgr.c. [How] * Pull get_active_display_cnt out to clk_mgr. * Pull out shared logic in set_dispclk and set_dprefclk Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Fix type of pp_smu_wm_set_range structEric Yang
[why] Value read from SMU is 16 bits, not 32. [How] Fix type, and add wm_type enum in preparation for future interfaces. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: do not power on eDP power rail earlyAnthony Koo
[Why] Modern Standby may toggle display adapter state between D0 and D3 state unpredictably. But events that cause transition to D0 are not always resulting in a display light up scenario. Modern eDP panels should be able to power on panel logic quickly upon VDD going high. Based on spec, the T3 time between VDD on and HPD high can be between 0 and 80 ms. Doing any tricky sorts of optimization by powering on panel VDD early during D0 transition on can negatively impact other features due to unnecessary power drain and toggling when final system state does not intend for the panel to be lit up. We need OEMs to source higher end panels that have T3 time close to 0 if they want quick S3/Modern Standby resume times. [How] Remove panel VDD power on in init_hw Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: fix crash on setmode when mode is close to bw limitSu Sung Chung
[why] during It's possible to call dcn_validate_bandwidth with no plane. In that case, as we are only intersted in if output timing is supported or not, even if we cannot support native resolution, we still want to support lower resolution if it is valid [how] if there exist no surface, make viewport/rec_out size at max 1080p. It is already known that 1080p x 6(max # of pipes) is supported, so if we fail validation, it is because of the stream Signed-off-by: Su Sung Chung <Su.Chung@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: fix calculation of total_data_read_bandwidthSu Sung Chung
[why] by adding fast_validate flag, we are skipping some portion of dcn_validate_bandwidth code that is not necessary for mode validation. However we have a bug where it does not calculate v->total_data_read_bandwidth, which is one of the factors determines the result of the validation, and therefore report false positive during mode validation. [how] add calculation of v->total_data_read_bandwidth outside of the region that is guarded by fast_validate flag Signed-off-by: Su Sung Chung <Su.Chung@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: 3.2.32Aric Cyr
Signed-off-by: Aric Cyr <aric.cyr@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Move link functions from dc to dc_linkChris Park
[Why] link-specific functions should reside in dc_link.c [How] Move them there. Signed-off-by: Chris Park <Chris.Park@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Add min_dcfclk_mhz field to bb overridesJun Lei
Add min_dcfclk_mhz to bounding box overrides. Signed-off-by: Jun Lei <Jun.Lei@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: move clk_mgr files to right placeEric Yang
[Why] Better organization [How] Move clk_mgr files under dc/clk_mgr Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: disable PSR/ABM before destroy DMCU structPaul Hsieh
[Why] 1. DMCU is not running on some platform but driver still send ABM command. It may cause assert due to DMCU is not alive. 2. To make sure PSR disable when driver disable [How] 1. Add dmcu_is_running in ABM struct, driver can check this flag to determine driver should send ABM command or not. 2. Send PSR disable command when destroy PSR Signed-off-by: Paul Hsieh <paul.hsieh@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Ensure DRR triggers in BPEryk Brol
[Why] In the previous implementation DRR event sometimes came in during FP2 region which is a keep-out zone. This would cause the frame not to latch until the next frame which resulted in heavy flicker. To fix this we need to make sure that it triggers in the BP. [How] 1. Remove DRR programming during flip 2. Setup manual trigger for DRR event and trigger it after surface programming is complete Signed-off-by: Eryk Brol <eryk.brol@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Add GSL source select registersKrunoslav Kovac
GSL is a form of locking that can be used to synchronize pipes in a pipe-split configurations when async flip is used. Add the registers here. Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Disable audio stream only if it's currently enabledEryk Brol
[Why] Previously there were 2 consecutive calls being made to disable audio stream. The first one disabled the audio stream, and the second one went through and also tried to disable the audio stream causing BACO entry issues due to the ASIC appearing busy. [How] 1. Add a status field to the audio struct which stores enabled/disabled info 2. In the calls to enable/disable audio stream check if we're already in the desired state before executing the function Signed-off-by: Eryk Brol <eryk.brol@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: assign new stream id in dc_copy_streamWenjing Liu
[why] stream id should uniquely identify an instance of stream. the copy constructor should be treated as a new stream instance. [how] assign a new stream id in this copy constructor. Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Move CLK_BASE_INNER macroEric Yang
This macro is specificly used by RV1. Move it to the appropriate location. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Implement CM dealpha and bias interfacesGary Kattan
Add vtable entries for de-alpha and bias color management interfaces. Move piece-wise transfer function registers to a helper list for future reuse. Signed-off-by: Gary Kattan <gary.kattan@amd.com> Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: Don't use ROM for output TF if GAMMA_CS_TFM_1DHugo Hu
We can’t use hardcoded SRGB ROM for output TF if we have GAMMA_CS_TFM_1D (unless we know 1D LUT is identity), so we never want to return here early. We apply the LUT part of ColorTransform3x4 only in apply_lut_1d() which is called near the end of that function. Signed-off-by: Hugo Hu <hugo.hu@amd.com> Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amd/display: make clk mgr soc specificEric Yang
[Why] First step of refactoring clk mgr to better handle different ways of handling clock operations. Clock operation policies are soc specific and not just DCN vesion specific. It is not a hw resource, should not be in the resource pool. [How] Change clock manager creation to be based on HW internal ID, rename clock manager members to be more clear. Move clock manager out of resource. Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amdgpu:Fix the unpin warning about csb bufferEmily Deng
As it will destroy clear_state_obj, and also will unpin it in the gfx_v9_0_sw_fini, so don't need to call amdgpu_bo_free_kernel in gfx_v9_0_sw_fini, or it will have unpin warning. Signed-off-by: Emily Deng <Emily.Deng@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/amdgpu: ras injection use gpu addressxinhui pan
injection need a valid gpu address. Signed-off-by: xinhui pan <xinhui.pan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-05-31drm/bridge: sii902x: Implement HDMI audio supportJyri Sarha
Implement HDMI audio support by using ASoC HDMI codec. The commit implements the necessary callbacks and configuration for the HDMI codec and registers a virtual platform device for the codec to attach. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/ef6895d016554b1e0c8b388d4993bcd6a3699341.1558964241.git.jsarha@ti.com
2019-05-31dt-bindings: display: sii902x: Add HDMI audio bindingsJyri Sarha
The sii902x chip family supports also HDMI audio. Add binding for describing the necessary i2s and mclk wiring for it. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/f790277fabc45f987f90075dd842368705226a84.1558964241.git.jsarha@ti.com
2019-05-31dt-bindings: display: sii902x: Remove trailing white spaceJyri Sarha
Remove trailing white space from sii902x display bridge binding. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/f1f2ef82c4e8ecea920c408bd4e569f5ed27d20a.1558964241.git.jsarha@ti.com
2019-05-31drm/bridge: sii902x: pixel clock unit is 10kHz instead of 1kHzJyri Sarha
The pixel clock unit in the first two registers (0x00 and 0x01) of sii9022 is 10kHz, not 1kHz as in struct drm_display_mode. Division by 10 fixes the issue. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1a2a8eae0b9d6333e7a5841026bf7fd65c9ccd09.1558964241.git.jsarha@ti.com
2019-05-31drm/bridge: sii902x: Set output mode to HDMI or DVI according to EDIDJyri Sarha
Set output mode to HDMI or DVI according to EDID HDMI signature. Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/c42838073b83185a5cf9949caab3c70ee093b791.1558964241.git.jsarha@ti.com
2019-05-31drm/bridge: sii902x: add input_bus_flagsTomi Valkeinen
The driver always sets InputBusFmt:EDGE to 0 (falling edge). Add drm_bridge_timings's input_bus_flags to reflect that the bridge samples on falling edges. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Jyri Sarha <jsarha@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/deb02a1fd508c514472a4e660092f301e6681361.1558964241.git.jsarha@ti.com
2019-05-31dt-bindings: tc358767: add HPD supportTomi Valkeinen
Add DT property for defining the pin used for HPD. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: devicetree@vger.kernel.org Cc: Rob Herring <robh@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-25-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: add IRQ and HPD supportTomi Valkeinen
Add support for interrupt and hotplug handling. Both are optional. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-24-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: add GPIO & interrupt registersTomi Valkeinen
Add GPIO and interrupt related registers for HPD work. Mark INTSTS_G and GPIOI as volatile. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-23-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: read display_props in get_modes()Tomi Valkeinen
We need to know the link bandwidth to filter out modes we cannot support, so we need to have read the display props before doing the filtering. To ensure we have up to date display props, call tc_get_display_props() in the beginning of tc_connector_get_modes(). Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-22-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: copy the mode data, instead of storing the pointerTomi Valkeinen
In tc_bridge_mode_set callback, we store the pointer to the given drm_display_mode, and use the mode later. Storing a pointer in such a way looks very suspicious to me, and I have observed odd issues where the timings were apparently (at least mostly) zero. Do a copy of the drm_display_mode instead to ensure we don't refer to freed/modified data. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-21-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: remove tc_connector_best_encoderTomi Valkeinen
drm_connector_helper_funcs.best_encoder is only needed when the connector can have more than one encoder, and that is never the case here. So remove tc_connector_best_encoder. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-20-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: use bridge mode_validTomi Valkeinen
We have tc_connector_mode_valid() to filter out videomdoes that the tc358767 cannot support. As it is a bridge limitation, change the code to use drm_bridge_funcs's mode_valid instead. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-19-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: remove check for video mode in link enableTomi Valkeinen
tc_main_link_enable() checks if videomode has been set, and fails if there's no videomode. As tc_main_link_enable() no longer depends on the videomode, we can drop the check. Also, while tc_stream_enable() does depend on the videomode, we can expect that a mode has been set before drm_bridge_funcs.enable is called, so we don't need the check there either. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-18-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: clean-up link trainingTomi Valkeinen
The current link training code does unnecessary retry-loops, and does extra writes to the registers. It is easier to follow the flow and ensure it's similar to Toshiba's documentation if we deal with LT inside tc_main_link_enable() function. This patch adds tc_wait_link_training() which handles waiting for the LT phase to finish, and does the necessary LT register setups in tc_main_link_enable, without extra loops. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-17-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: cleanup LT result checkTomi Valkeinen
The driver has a loop after ending link training, where it reads the DPCD link status and prints an error if that status is not ok. The loop is unnecessary, as far as I can understand from DP specs, so let's remove it. We can also print the more specific errors to help debugging. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-16-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: use more reliable seq when finishing LTTomi Valkeinen
At the end of the link training, two steps have to be taken: 1) tc358767's LT mode is disabled by a write to DP0_SRCCTRL, and 2) Remove LT flag in DPCD 0x102. Toshiba's documentation tells to first write the DPCD, then modify DP0_SRCCTRL. In my testing this often causes issues, and the link disconnects right after those steps. If I reverse the steps, it works every time. There's a chance that this is DP sink specific, though, but as my testing shows this sequence to be much more reliable, let's change it. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-15-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: remove unnecessary msleepTomi Valkeinen
For some reason the driver has a msleep(100) after writing to DP_PHY_CTRL. Toshiba's documentation doesn't suggest any delay is needed, and I have not seen any issues with the sleep removed. Drop it, as msleep(100) is a rather big one. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-14-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: ensure DP is disabled before LTTomi Valkeinen
Link training will sometimes fail if the DP link is enabled when tc_main_link_enable() is called. The driver makes sure the DP link is disabled when the DP output is disabled, and we never enable the DP without first disabling it, so this should never happen. However, as the HW behavior seems to be somewhat random if DP link has erroneously been left enabled, let's add a WARN_ON() for the case and set DP0CTL to 0. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-13-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: disable only video stream in tc_stream_disableTomi Valkeinen
Currently the code writes 0 to DP0CTL in tc_stream_disable(), which disables the whole DP link instead of just the video stream. We always disable the link and the stream together from tc_bridge_disable(), so this doesn't cause any issues. Nevertheless, fix this by only clearing VID_EN in tc_stream_disable to stop the video stream while keeping the link enabled. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-12-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: add link disable functionTomi Valkeinen
Currently we have tc_main_link_setup(), which configures and enabled the link, but we have no counter-part for disabling the link. Add tc_main_link_disable, and rename tc_main_link_setup to tc_main_link_enable. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-11-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: move PXL PLL enable/disable to stream enable/disableTomi Valkeinen
We set up the PXL PLL inside tc_main_link_setup. This is unnecessary, and makes tc_main_link_setup depend on the video-mode, which should not be the case. As PXL PLL is used only for the video stream (and only when using the HW test pattern), let's move the PXL PLL setup into tc_stream_enable. Also, currently the PXL PLL is only disabled if the driver if removed. Let's disable the PXL PLL when the stream is disabled. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-10-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: split stream enable/disableTomi Valkeinen
It is nicer to have enable/disable functions instead of set(bool enable) style function. Split tc_main_link_stream into tc_stream_enable and tc_stream_disable. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-9-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: move video stream setup to tc_main_link_streamTomi Valkeinen
The driver currently sets the video stream registers in tc_main_link_setup. One should be able to establish the DP link without any video stream, so a more logical place is to configure the stream in the tc_main_link_stream. So move them there. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-8-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: cleanup aux_link_setupTomi Valkeinen
The driver sets up AUX link at probe time, but, for some reason, also sets the main link's number of lanes using tc->link.base.num_lanes. This is not needed nor correct, as the number of lanes has not been decided yet. The number of lanes will be set later during main link setup. Modify aux_link_setup so that it does not use tc->link, and thus makes aux setup independent of the link probing. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-7-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: remove unused swing & preempTomi Valkeinen
swing and preemp fields are not used. Remove them. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-6-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: cleanup spread & scrambler_disTomi Valkeinen
Minor cleanups: - Use bool for boolean fields - Use DP_MAX_DOWNSPREAD_0_5 instead of BIT(0) - debug print down-spread and scrambler status Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-5-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: fix ansi 8b10b useTomi Valkeinen
DP always uses ANSI 8B10B encoding. Some monitors (old?) may not have the ANSI 8B10B bit set in DPCD, even if it should always be set. The tc358767 driver currently respects that flag, and turns the encoding off if the monitor does not have the bit set, which then results in the monitor not working. This patch makes the driver to always use ANSI 8B10B encoding, and drops the 'coding8b10b' field which is no longer used. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-4-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: reset voltage-swing & pre-emphasisTomi Valkeinen
We need to reset DPCD voltage-swing & pre-emphasis before starting the link training, as otherwise tc358767 will use the previous values as minimums. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-3-tomi.valkeinen@ti.com
2019-05-31drm/bridge: tc358767: fix tc_aux_get_status error handlingTomi Valkeinen
tc_aux_get_status() does not report AUX_TIMEOUT correctly, as it only checks the AUX_TIMEOUT if aux is still busy. Fix this by always checking for AUX_TIMEOUT. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-2-tomi.valkeinen@ti.com
generated by cgit (git 2.34.1) at 2025-09-11 00:43:03 +0000